NX301113

PRODUCT DATASHEET SynJet® LED Cooler R87-46 SynJet cooling technology provides the most reliable thermal management solution available. This LED cooler has been developed by Nuventix for cooling downlight and spotlight modules and arrays. • • • • • • Cools up to 38 W 4 Reliable 100K Hours Lifetime Energy Efficient 5 Yr Warranty Small Form Factor Quiet Acoustics Specifications 1 Thermal & Acoustic SynJet Setting 2 Θs-a Al 3 4 TDP (W) ΔT = 30° / 40°C SPL 5 (dBA) Wire Connections Mid Performance 0.84 36 / 48 25 Red to +VDC Black & Blue to Ground Standard Performance 0.92 33 / 43 22 Red to +VDC Black only to Ground Silent Performance 1.03 29 / 39 19 Red to +VDC Black & Purple to Ground PWM at 100% duty cycle 0.79 38 / 51 27 Red to +VDC Black only to Ground Blue to PWM Signal Heatsink Only 2.41 12 N/A N/A N/A Electrical SynJet Setting 2 Mid Standard Silent PWM at 100% duty cycle Current (mA) Voltage (VDC) +/- 10% Imin 5 20 Iavg 150 95 65 160 6 6 Ipeak 300 190 130 320 Pavg (mW) 750 475 325 800 Current (mA) Voltage (VDC) +/- 10% Imin 12 10 Iavg 67 50 40 82 Ipeak 134 100 80 164 Pavg (mW) 800 600 480 980 Environmental All Settings Operating Temperature Storage Temperature Storage Altitude Operating Relative Humidity Weight Reliability Regulatory Compliance Min -40 -50 5 Max 70 75 15K 95 335 100K Units °C °C m % g hrs Conditions Air temperature surrounding cooler Air temperature surrounding cooler Above sea level Non-condensing SynJet with Al heat sink L10 @ 60°C RoHS, UL, FCC Part 15 Class B, CE Mechanical - SynJet Cooling Solution shown with Configurable heat sink 1 All values are typical at 25ºC unless otherwise stated. The Level Select model should be used for discrete performance settings. Follow the instructions in the Product Design Guide for adjusting settings. Thermal resistance values are given as reference only and are measured in free air without airflow obstructions. Thermal resistance is measured from the bottom middle of the heat sink to ambient air measured at the inlet to the SynJet, with a heat source at least 4.1cm2 using the 60 W reference heat sink. Actual thermal performance may vary by application and final product design should be tested to assure proper thermal performance. 4 Thermal Design Power is based on a 30ºC or 40ºC temperature rise of heat sink mounting surface above ambient temperature around cooler. 5 Sound Pressure Level is measured at 1 meter distance per ISO 7779. 6 The SynJet has a time varying current. The current waveform is sinusoidal and the average current (Iavg) is used to calculate the average power consumption (Pavg) at nominal input voltage (VDC). See the Electrical section in the Product Design Guide for a detailed explanation. 2 3 4635 Boston Lane Austin, TX 78735 Phone: 512-382-8100 www.nuventix.com MKTG-DOC-000152 Revision A01 Jan 2013 r1 PRODUCT DATASHEET All dimensions are nominal and in mm unless otherwise stated. See product drawings for more detail. SynJet Wire Harness Connector Pinout Pin 1 2 Wire Color Red Black Symbol +VDC GND 3 Purple CTRL2 4 Blue CTRL1 Description 5 V or 12 V depending on model Ground Input for Level Select model Status signal for PWM model Input for Level Select model PWM input for PWM model IMPORTANT: SynJets should be completely wired to the power supply before the power supply is energized. The power supply should be turned off before the SynJet Cooler is disconnected. SynJet Coolers are not designed for “hot swap” or “hot plug” applications. Part Numbers Part Number Description Notes NX201100 NX201101 NX201102 NX201103 NX301103 NX301109 NX301110 NX301111 SynJet, ZFlow 87, PWM, 5V, Black SynJet, ZFlow 87, Level Select, 5V, Black SynJet, ZFlow 87, PWM, 12V, Black SynJet, ZFlow 87, Level Select, 12V, Black Heatsink, R87-46, Configurable, Black Heatsink, R87-46, Bridgelux RS, Black Heatsink, R87-46, Xicato XSM, Vossloh Schwabe Luga Shop, Black Heatsink, R87-46, Citizen CLL030, CLL050, Ledil, Black Heatsink, R87-46, Osram Soleriq, Ledil, Sharp Megazenigata, Molex, Black Heatsink, R87-46, Philips Luxeon K, Black Wire Harness, 4-Wire, 150 mm Length Wire Harness, 4-Wire, 600 mm Length Use with PWM input to control performance setting Configurable to discrete performance settings Use with PWM input to control performance setting Configurable to discrete performance settings Contact sales for other heatsink options Contact sales for other heatsink options Contact sales for other heatsink options Contact sales for other heatsink options NX301112 NX301113 WALLS-C4150-001 WALLS-C4600-001 Contact sales for other heatsink options Contact sales for other heatsink options Contact sales for other wire harness options Contact sales for other wire harness options Nuventix reserves the right to make changes to the products or information contained herein without notice. No liability is assumed as a result of their use or applications. For additional information, please contact Nuventix directly. 4635 Boston Lane Austin, TX 78735 Phone: 512-382-8100 www.nuventix.com MKTG-DOC-000152 Revision A01 Jan 2013 r1