Dual Low Offset, Low Power
Operational Amplifier
OP200
Data Sheet
PIN CONNECTIONS
Low input offset voltage: 75 μV maximum
Low offset voltage drift, over −55°C < TA < +125°C
0.5 μV/°C maximum
Low supply current (per amplifier): 725 μA maximum
High open-loop gain: 5000 V/mV minimum
Low input bias current: 2 nA maximum
Low noise voltage density: 11 nV/√Hz at 1 kHz
Stable with large capacitive loads: 10 nF typical
–IN A 1
16 OUT A
+IN A 2
15 NC
NC 3
14 NC
V– 4
13 V+
NC 5
12 NC
+IN B 6
11 NC
–IN B 7
10 OUT B
NC 8
9
NC
NC = NO CONNECT
00322-001
FEATURES
OUT A
1
–IN A
2
+IN A
3
V–
4
OP200
A
B
8
V+
7
OUT B
6
–IN B
5
+IN B
00322-002
Figure 1. 16-Lead SOIC (S-Suffix)
Figure 2. 8-Lead PDIP (P-Suffix)
8-Lead CERDIP (Z-Suffix)
GENERAL DESCRIPTION
The OP200 is the first monolithic dual operational amplifier
to offer OP77 type precision performance. Available in the
industry standard 8-lead pinout, the OP200 combines precision
performance with the space and cost savings offered by a dual
amplifier.
The OP200 features an extremely low input offset voltage of
less than 75 μV with a drift below 0.5 μV/°C, guaranteed over
the full military temperature range. Open-loop gain of the OP200
exceeds 5,000,000 into a 10 kΩ load; input bias current is under
2 nA; CMRR is over 120 dB; and PSRR is below 1.8 μV/V. On-chip
Zener zap trimming is used to achieve the extremely low input
offset voltage of the OP200 and eliminates the need for offset
pulling.
Rev. G
Power consumption of the OP200 is low, with each amplifier
drawing less than 725 μA of supply current. The total current
drawn by the dual OP200 is less than one-half that of a single
OP07, yet the OP200 offers significant improvements over this
industry-standard op amp. The voltage noise density of the OP200,
11 nV/√Hz at 1 kHz, is half that of most competitive devices.
The OP200 is an ideal choice for applications requiring multiple
precision op amps and where low power consumption is critical.
For a quad precision op amp, see the OP400.
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©1978–2017 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
OP200
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Applications Information .............................................................. 12
Pin Connections ............................................................................... 1
Dual Low Power Instrumentation Amplifier ......................... 12
General Description ......................................................................... 1
Precision Absolute Value Amplifier ......................................... 12
Revision History ............................................................................... 2
Precision Current Pump ............................................................ 12
Specifications..................................................................................... 4
Dual 12-Bit Voltage Output DAC ............................................ 13
Electrical Characteristics ............................................................. 4
Dual Precision Voltage Reference ............................................ 13
Absolute Maximum Ratings ............................................................ 7
Programmable High Resolution Window Comparator ........ 14
Thermal Resistance ...................................................................... 7
Outline Dimensions ....................................................................... 15
ESD Caution .................................................................................. 7
Ordering Guide .......................................................................... 16
Typical Performance Characteristics ............................................. 8
REVISION HISTORY
3/2017—Rev. F to Rev. G
Changes to Figure 21 ...................................................................... 10
10/2015—Rev. E to Rev. F
Changes to General Description .................................................... 1
Changes to Ordering Guide .......................................................... 16
9/2012—Rev. D to Rev. E
Changed Table 2 Conditions from VS = 15 V to VS = ±15 V ...... 4
Updated Outline Dimensions ....................................................... 15
Changes to Ordering Guide .......................................................... 16
2/2009—Rev. C to Rev. D
Change to Large Signal Voltage Gain, Table 2 .............................. 4
Changes to Ordering Guide .......................................................... 16
8/2008—Rev. B to Rev. C
Updated Format .................................................................. Universal
Changes to Features Section............................................................ 1
Changes to Table 1 and Table 2 ....................................................... 4
Changes to Table 3 and Table 4 ....................................................... 5
Deleted Table 7; Renumbered Sequentially................................... 5
Changes to Figure 15.........................................................................9
Changes to Figure 21...................................................................... 10
Changes to Figure 30 and Figure 31 ............................................ 12
Changes to Programmable High Resolution Window
Comparator Section, Figure 33, and Figure 34 .......................... 13
Changes to Figure 35...................................................................... 14
Updated Outline Dimensions ....................................................... 15
Changes to Ordering Guide .......................................................... 16
2/2004—Rev. A to Rev. B.
OP200F Deleted .................................................................. Universal
Changes to Ordering Guide .............................................................5
Changes to Figure 4 ...........................................................................8
Updated Outline Dimension ........................................................ 11
4/2002—Rev. 0 to Rev. A.
Edits to Features.................................................................................1
Edits to General Description ...........................................................1
Edits to Ordering Information ........................................................1
Edits to Pin Connections ..................................................................1
Edits to Absolute Maximum Ratings ..............................................2
Edits to Package Type .......................................................................2
Rev. G | Page 2 of 16
Data Sheet
OP200
V+
BIAS
OUT
VOLTAGE
LIMITING
NETWORK
–IN
V–
Figure 3. Simplified Schematic (One of Two Amplifiers Shown)
Rev. G | Page 3 of 16
00322-003
+IN
OP200
Data Sheet
SPECIFICATIONS
ELECTRICAL CHARACTERISTICS
VS = ±15 V, TA = 25°C, unless otherwise noted.
Table 1.
Parameter
INPUT CHARACTERISTICS
Input Offset Voltage
Long-Term Input Voltage Stability
Input Offset Current
Input Bias Current
Input Noise Voltage
Input Noise Voltage Density 1
Input Noise Current
Input Noise Current Density
Input Resistance Differential Mode
Input Resistance Common Mode
Large Signal Voltage Gain
1
Symbol
Conditions
OP200A/OP200E
Min
Typ
Max
VOS
IOS
IB
en p-p
en
in p-p
in
RIN
RINCM
AVO
25
0.1
0.05
0.1
0.5
22
11
15
0.4
10
125
VCM = 0 V
VCM = 0 V
0.1 Hz to 10 Hz
fO = 10 Hz
fO = 1000 Hz
0.1 Hz to 10 Hz
fO = 10 Hz
VO = ±10 V
RL = 10 kΩ
RL = 2 kΩ
5000
2000
Min
75
80
0.1
0.05
0.1
0.5
22
11
15
0.4
10
125
1.0
2.0
36
18
12,000
3700
OP200G
Typ
Max
3000
1500
200
3.5
5.0
Unit
μV
μV/mo
nA
nA
μV p-p
nV/√Hz
nV/√Hz
pA p-p
pA/√Hz
MΩ
GΩ
7000
3200
M/mV
M/mV
OP200A
Typ
Max
Unit
45
0.2
0.15
0.9
125
0.5
2.5
5.0
μV
μV/°C
nA
nA
Sample tested.
VS = ±15 V, −55°C ≤ TA ≤ +125°C for OP200A, unless otherwise noted.
Table 2.
Parameter
INPUT CHARACTERISTICS
Input Offset Voltage
Average Input Offset Voltage Drift
Input Offset Current
Input Bias Current
Large Signal Voltage Gain
Input Voltage Range 1
Common-Mode Rejection Ratio
Capacitive Load Stability
POWER SUPPLY
Power Supply Rejection Ratio
Supply Current Per Amplifier
OUTPUT CHARACTERISTICS
Output Voltage Swing
1
Symbol
VOS
TCVOS
IOS
IB
AVO
IVR
CMRR
Conditions
VCM = 0 V
VCM = 0 V
VO = 10 V
RL = 10 kΩ
RL = 2 kΩ
VCM = ±12 V
AV = 1
PSRR
ISY
VS = 3 V to 18 V
No load
VO
RL = 10 kΩ
RL = 2 kΩ
Min
3000
1000
±12
115
9000
2700
±12.5
130
8
0.2
600
±12
±11
Guaranteed by CMRR test.
Rev. G | Page 4 of 16
±12.4
±12
V/mV
V/mV
V
dB
nF
3.2
775
μV/V
μA
V
V
Data Sheet
OP200
VS = ±15 V, TA = 25°C, unless otherwise noted.
Table 3.
Parameter
INPUT CHARACTERISTICS
Input Voltage Range 1
Common-Mode Rejection Ratio
Channel Separation 2
Input Capacitance
Capacitive Load Stability
POWER SUPPLY
Power Supply Rejection Ratio
Supply Current Per Amplifier
OUTPUT CHARACTERISTICS
Output Voltage Swing
DYNAMIC PERFORMANCE
Slew Rate
Gain Bandwidth Product
1
2
Symbol
Conditions
OP200A/OP200E
Min
Typ
Max
Min
IVR
CMRR
CS
CIN
VCM = ±12 V
VO = 20 V p-p, fO = 10 Hz
±12
120
123
±12
110
123
AV = 1, no oscillations
±13
135
145
3.2
10
PSRR
ISY
VS = ±3 V to ±18 V
No load
0.4
570
VO
RL= 10 kΩ
RL = 2 kΩ
SR
GBP
1.8
725
OP200G
Typ
Max
±13
130
145
3.2
10
0.6
570
Unit
V
dB
dB
pF
nF
5.6
725
μV/V
μA
±12
±11
±12.6
±12.2
±12
±11
±12.6
±12.2
V
V
0.1
0.15
500
0.1
0.15
500
V/μs
kHz
AV = 1
Guaranteed by CMRR test.
Guaranteed but not 100% tested.
VS = ±15 V, −40°C ≤ TA ≤ +85°C, unless otherwise noted.
Table 4.
Parameter
INPUT CHARACTERISTICS
Input Offset Voltage
Average Input Offset Voltage Drift
Input Offset Current
Input Bias Current
Large-Signal Voltage Gain
Input Voltage Range 1
Common-Mode Rejection Ratio
Capacitive Load Stability
POWER SUPPLY
Power Supply Rejection Ratio
Supply Current Per Amplifier
OUTPUT CHARACTERISTICS
Output Voltage Swing
1
Symbol
VOS
TCVOS
IOS
IB
AVO
IVR
CMRR
Conditions
VCM = 0 V
VCM = 0 V
VO = ±10 V
RL= 10 kΩ
RL = 2 kΩ
VCM = ±12 V
AV = 1, no oscillations
PSRR
ISY
VS = ±3 V to ±18 V
No load
VO
RL = 10 kΩ
RL = 2 kΩ
Min
3000
1500
±12
115
Rev. G | Page 5 of 16
Max
35
0.2
0.08
03
100
0.5
2.5
5.0
10,000
3200
±12.5
130
10
0.15
600
±12
±11
Guaranteed by CMRR test.
OP200E
Typ
±12.4
±12
Min
OP200G
Typ
Max
110
0.6
0.1
0.5
2000
1000
±12
105
3.2
775
5000
2500
±12.5
130
10
0.3
600
±12
±11
300
2.0
6.0
10.0
±12.4
±12.2
Unit
μV
μV/°C
nA
nA
V/mV
V/mV
V
dB
nF
10.0
775
μV/V
μA
V
V
OP200
Data Sheet
1/2
OP200
V1 20V p-p @ 10Hz
50Ω
50Ω
1/2
OP200
00322-004
CHANNEL SEPARATION = 20 log
V2
V1
V2/1000
Figure 4. Channel Separation Test Circuit
1/2
OP200
10kΩ
1/2
OP200
eOUT TO SPECTRUM
ANALYZER
eOUT (nV/√Hz) = √2 × eOUT (nV/√Hz) × 101
Figure 5. Noise Test Schematic
Rev. G | Page 6 of 16
00322-005
100Ω
Data Sheet
OP200
ABSOLUTE MAXIMUM RATINGS
THERMAL RESISTANCE
Table 5.
Parameter
Supply Voltage
Differential Input Voltage
Input Voltage
Output Short-Circuit Duration
Storage Temperature Range
Lead Temperature (Soldering, 60 sec)
Junction Temperature Range (TJ)
Operating Temperature Range
OP200A
OP200E, OP200G
Table 6.
Rating
±20 V
±30 V
Supply voltage
Continuous
−65°C to +150°C
300°C
−65°C to +150°C
Package Type
8-Lead CERDIP (Z Suffix)
8-Lead Plastic DIP (P Suffix)
16-Lead SOIC (S Suffix)
1
θJC
16
37
27
Unit
°C/W
°C/W
°C/W
θJA is specified for worst-case mounting conditions, that is, θJA is specified for
device in socket for CERDIP and PDIP packages; θJA is specified for device
soldered to printed circuit board for SOIC package.
ESD CAUTION
−55°C to +125°C
−40°C to +85°C
θJA1
148
96
92
Stresses at or above those listed under Absolute Maximum Ratings
may cause permanent damage to the product. This is a stress
rating only; functional operation of the product at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Operation beyond
the maximum operating conditions for extended periods may
affect product reliability.
Rev. G | Page 7 of 16
OP200
Data Sheet
TYPICAL PERFORMANCE CHARACTERISTICS
VS = ±15V
INPUT OFFSET CURRENT (pA)
2
250
1
200
150
100
0
0
1.0
2.0
3.0
4.0
0
–75
5.0
00322-009
50
00322-006
CHANGE IN OFFSET VOLTAGE (µV)
300
TA = 25°C
VS = ±15V
–50
–25
Figure 6. Warm-Up Drift
100
125
0.8
INPUT BIAS CURRENT (nA)
40
30
20
0.6
0.4
0.2
00322-007
10
–50
–25
0
25
50
75
100
0
–15
125
00322-010
INPUT OFFSET VOLTAGE (µV)
75
TA = 25°C
VS = ±15V
50
–10
–5.0
0
5.0
Figure 7. Input Offset Voltage vs. Temperature
140
COMMON-MODE REJECTION (dB)
2
1
0
–1
00322-008
–2
0
25
50
75
100
120
100
80
60
40
20
0
125
TA = 25°C
VS = ±15V
00322-011
VS = ±15V
–25
15
Figure 10. Input Bias Current vs. Common-Mode Voltage
3
–50
10
COMON-MODE VOLTAGE (V)
TEMPERATURE (°C)
INPUT BIAS CURRENT (nA)
50
1.0
VS = ±15V
–3
–75
25
Figure 9. Input Offset Current vs. Temperature
60
0
–75
0
TEMPERATURE (°C)
TIME (Minutes)
1
10
100
1k
10k
FREQUENCY (Hz)
TEMPERATURE (°C)
Figure 11. Common-Mode Rejection vs. Frequency
Figure 8. Input Bias Current vs. Temperature
Rev. G | Page 8 of 16
100k
Data Sheet
OP200
1.18
10
00322-012
TOTAL SUPPLY CURRENT (mA)
VOLTAGE NOISE DENSITY (nV/√Hz)
TA = 25°C
VS = ±15V
1
10
100
TWO AMPLIFIERS
TA = 25°C
1.16
1.14
1.12
1.10
1.08
00322-015
100
1.06
±2
1k
±6
FREQUENCY (Hz)
Figure 12. Voltage Noise Density vs. Frequency
1.16
TWO AMPLIFIERS
VS = ±15V
00322-013
TOTAL SUPPLY CURRENT (mA)
CURRENT NOISE DENSITY (fA/√Hz)
10
±18
Figure 15. Total Supply Current vs. Supply Voltage
TA = 25°C
VS = ±15V
1
±14
100
1.15
1.14
1.13
1.12
1.11
–75
1k
00322-016
1000
100
±10
SUPPLY VOLTAGE (V)
–50
–25
FREQUENCY (Hz)
0
25
50
75
100
125
TEMPERATURE (°C)
Figure 13. Current Noise Density vs. Frequency
Figure 16. Total Supply Current vs. Temperature
0
2
4
6
8
NEGATIVE SUPPLY
120
100
80
60
POSITIVE SUPPLY
40
20
00322-017
00322-014
NOISE VOLTAGE (400nV/DIV)
POWER SUPPLY REJECTION (nA)
140
TA = 25°C
0
0.1
10
1
10
100
1k
10k
FREQUENCY (Hz)
TIME (SEC)
Figure 14. 0.1 Hz to 10 Hz Noise
Figure 17. Power Supply Rejection vs. Frequency
Rev. G | Page 9 of 16
100k
OP200
Data Sheet
100
TA = 25°C
VS = ±15V
80
CLOSED-LOOP GAIN (dB)
0.6
0.5
0.4
0.3
60
40
20
0
AV = 1000
AV = 100
AV = 10
AV = 1
–20
0.1
–75
00322-018
0.2
–50
–25
0
25
50
75
100
00322-021
POWER SUPPLY REJECTION (µV/V)
0.7
–40
1
125
10
100
1k
10k
FREQUENCY (Hz)
TEMPERATURE (°C)
30
6000
TA = 25°C
VS = ±15V
VS = ±15V
RL = 2kΩ
5000
25
V p-p AT 1%
DISTORTION
OUTPUT SWING (V)
4000
3000
2000
15
10
00322-019
–50
–25
0
25
50
TEMPERATURE (°C)
75
100
00322-022
5
1000
0
–75
20
0
10
125
100
1k
1
AV = 100
0
60
PHASE
90
40
GAIN
20
135
180
0
–20
10
100
1k
10k
100k
00322-020
80
PHASE SHIFT (Degrees)
100
TOTAL HARMONIC DISTORTION (%)
TA = 25°C
VS = ±15V
120
100k
Figure 22. Maximum Output Swing vs. Frequency
Figure 19. Open-Loop Gain vs. Temperature
140
10k
FREQUENCY (Hz)
1M
AV = 10
0.1
AV = 1
0.01
TA = 25°C
VS = ±15V
VOUT = 10V p-p
RL = 2kΩ
0.001
100
1k
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 23. Total Harmonic Distortion vs. Frequency
Figure 20. Open-Loop Gain and Phase Shift vs. Frequency
Rev. G | Page 10 of 16
00322-023
OPEN-LOOP GAIN (V/mV)
1M
Figure 21. Closed-Loop Gain vs. Frequency
Figure 18. Power Supply Rejection vs. Temperature
OPEN-LOOP GAIN (dB)
100k
10k
Data Sheet
OP200
50
TA = 25°C
VS = ±15V
45
40
FALLING
OVERSHOOT (%)
35
30
25
RISING
20
15
5
0
0
0.5
1.0
1.5
2.0
2.5
3.0
5.00V
CAPACITIVE LOAD (nF)
100µs
TA = 25°C
VS = ±15V
AV = +1
00322-027
00322-024
10
Figure 27. Large Signal Transient Response
Figure 24. Overshoot vs. Capacitive Load
29
TA = 25°C
VS = ±15V
27
26
SINKING
25
TA = 25°C
VS = ±15V
AV = +1
24
SOURCING
00322-025
23
22
0
1
2
3
4
5
20mV
TIME (Minutes)
Figure 25. Short-Circuit Current vs. Time
00322-028
SHORT-CIRCUIT CURRENT (mA)
28
5µs
Figure 28. Small Signal Transient Response
150
130
120
110
TA = 25°C
VS = ±15V
AV = +1
100
100
1k
10k
100k
20mV
FREQUENCY (Hz)
Figure 26. Channel Separation vs. Frequency
5µs
Figure 29. Small Signal Transient Response, CLOAD = 1 nF
Rev. G | Page 11 of 16
00322-029
90
10
00322-026
CHANNEL SEPARATION (dB)
140
OP200
Data Sheet
APPLICATIONS INFORMATION
The OP200 is inherently stable at all gains and is capable of
driving large capacitive loads without oscillating. Nonetheless,
good supply decoupling is highly recommended. Proper supply
decoupling reduces problems caused by supply line noise and
improves the capacitive load driving capability of the OP200.
DUAL LOW POWER INSTRUMENTATION
AMPLIFIER
A dual instrumentation amplifier that consumes less than 33 mW
of power per channel is shown in Figure 30. The linearity of the
instrumentation amplifier exceeds 16 bits in gains of 5 to 200 and is
better than 14 bits in gains from 200 to 1000. CMRR is above
115 dB (gain = 1000). Offset voltage drift is typically 0.2 μV/°C
over the military temperature range, which is comparable to the
best monolithic instrumentation amplifiers. The bandwidth of
the low power instrumentation amplifier is a function of gain
and is shown in Table 7.
PRECISION ABSOLUTE VALUE AMPLIFIER
The circuit in Figure 31 is a precision absolute value amplifier
with an input impedance of 10 MΩ. The high gain and low TCVOS
of the OP200 ensure accurate operation with microvolt input
signals. In this circuit, the input always appears as a commonmode signal to the op amps. The CMRR of the OP200 exceeds
120 dB, yielding an error of less than 2 ppm.
+15V
C2
0.1pF
R1
1kΩ
C1
30pF
2
1/2
OP200AZ
R2
2kΩ
00322-031
The maximum output current of the precision current pump
shown in Figure 32 is ±10 mA. Voltage compliance is ±10 V
with ±15 V supplies. Output impedance of the current transmitter exceeds 3 MΩ with linearity better than 16 bits.
8
1
R3
10kΩ
VOUT
2
7
4
R1
10kΩ
–15V
20kΩ
5kΩ
5kΩ
–
VIN
+
VOUT = 5 +
40,000
RG
VIN + VREF
00322-030
RG
2
1/2
OP200EZ
R5
100Ω
1
IOUT
3
+15V
R4
1kΩ
Figure 30. Dual Low Power Instrumentation Amplifier
The output signal is specified with respect to the reference
input, which is normally connected to analog ground. The
reference input can be used to offset the output from −10 V
to +10 V if required.
R1
10kΩ
8
7
5
1/2
OP200EZ
6
IOUT =
VIN
VIN
=
= 10mA/V
RS 100Ω
4
–15V
Figure 32. Precision Current Pump
Rev. G | Page 12 of 16
00322-032
VREF
D1
1N4148
4
6
20kΩ
VOUT
0V < VOUT < 10V
PRECISION CURRENT PUMP
1/2
OP200AZ
1/2
OP200AZ
7
Figure 31. Precision Absolute Value Amplifier
3
–
1/2
OP200AZ
–15V
+15V
5
6
5
C2
0.1pF
Bandwidth
150 kHz
67 kHz
7.5 kHz
500 Hz
+
VIN
1
3
VIN
Table 7. Gain Bandwidth
Gain
5
10
100
1000
D1
1N4148
8
R3
1kΩ
Data Sheet
OP200
DUAL 12-BIT VOLTAGE OUTPUT DAC
DUAL PRECISION VOLTAGE REFERENCE
The dual output DAC shown in Figure 33 is capable of providing
untrimmed 12-bit accurate operation over the entire military
temperature range. Offset voltage, bias current, and gain errors
of the OP200 contribute less than 1/10 of an LSB error at 12 bits
over the military temperature range.
A dual OP200 and a REF43, a 2.5 V reference, can be used to
build a ±2.5 V precision voltage reference. Maximum output
current from each reference is ±10 mA with load regulation
under 25 μV/mA. Line regulation is better than 15 μV/V and
output voltage drift is under 20 μV/°C. Output voltage noise
from 0.1 Hz to 10 Hz is typically 75 μV p-p. R1 and D1 ensure
correct startup.
5V
21
VDD
RFB A 3
DAC A
1/2
DAC8221
IOUT A 2
8
DAC8221
10V
REFERENCE
VOLTAGE
4
VREF A
2
1/2
OP200AZ
3
1
OUT A
4
V–
DAC DATA BUS
PIN 6 (MSB) TO PIN 17 (LSB)
RFB B 23
DAC B
1/2
DAC8221
22 VREF B
18
19
DAC
CONTROL
20
IOUT B 24
6
1/2
OP200AZ
7
OUT B
5
DAC A/DAC B
AGND 1
CS
WR
00322-033
DGND
5
Figure 33. Dual 12-Bit Voltage Output DAC
+5V
R1
22kΩ
D1
1N914
+2.5V
+5V
2
VOUT
REF43
TRIM
GND 4
6
5
2
3
8
1/2
OP200AZ
1
R3
10kΩ
4
–5V
6
5
1/2
OP200AZ
7
R4
5kΩ
–2.5V
Figure 34. Dual Precision Voltage Reference
Rev. G | Page 13 of 16
00322-034
VIN
R3
10kΩ
OP200
Data Sheet
range. A dual CMOS 12-bit DAC, the DAC8221, is used in the
voltage switching mode to set the upper and lower thresholds
(DAC A and DAC B, respectively).
PROGRAMMABLE HIGH RESOLUTION WINDOW
COMPARATOR
The programmable window comparator shown in Figure 35 is
easily capable of 12-bit accuracy over the full military temperature
15V
VIN
21
VDD
10V
REFERENCE
VOLTAGE
2 IOUT A
8
DAC A
1/2
DAC8221
VREF A
3
4
R1
10kΩ
2
1/2
OP200AZ
1
D1
1N4148
DAC DATA BUS
PIN 6 (MSB) TO PIN 17 (LSB)
15V–
R2
10kΩ
18
DAC
CONTROL
SIGNALS
19
20
IOUT B
DAC B
1/2
DAC8221
VREF B 22
D1
1N4148
5
6
1/2
OP200AZ
7
TTL OUT
R4
10kΩ
Q1
2N2222
DAC A/DAC B
CS
WR
DGND
5
AGND
00322-035
24
4
5V
R2
10kΩ
1
Figure 35. Programmable High Resolution Window Comparator
Rev. G | Page 14 of 16
Data Sheet
OP200
OUTLINE DIMENSIONS
0.005 (0.13)
MIN
8
0.055 (1.40)
MAX
5
0.310 (7.87)
0.220 (5.59)
1
4
0.100 (2.54) BSC
0.320 (8.13)
0.290 (7.37)
0.405 (10.29) MAX
0.060 (1.52)
0.015 (0.38)
0.200 (5.08)
MAX
0.150 (3.81)
MIN
0.200 (5.08)
0.125 (3.18)
0.023 (0.58)
0.014 (0.36)
0.070 (1.78)
0.030 (0.76)
SEATING
PLANE
15°
0°
0.015 (0.38)
0.008 (0.20)
CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 36. 8-Lead Ceramic Dual In-Line Package [CERDIP]
(Q-8)
Z-Suffix
Dimensions shown in inches and (millimeters)
0.400 (10.16)
0.365 (9.27)
0.355 (9.02)
8
1
5
4
0.280 (7.11)
0.250 (6.35)
0.240 (6.10)
0.100 (2.54)
BSC
0.060 (1.52)
MAX
0.210 (5.33)
MAX
0.015
(0.38)
MIN
0.150 (3.81)
0.130 (3.30)
0.115 (2.92)
SEATING
PLANE
0.022 (0.56)
0.018 (0.46)
0.014 (0.36)
0.325 (8.26)
0.310 (7.87)
0.300 (7.62)
0.195 (4.95)
0.130 (3.30)
0.115 (2.92)
0.015 (0.38)
GAUGE
PLANE
0.005 (0.13)
MIN
0.014 (0.36)
0.010 (0.25)
0.008 (0.20)
0.430 (10.92)
MAX
COMPLIANT TO JEDEC STANDARDS MS-001
CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
CORNER LEADS MAY BE CONFIGURED AS WHOLE OR HALF LEADS.
Figure 37. 8-Lead Plastic Dual In-Line Package [PDIP]
(N-8)
P-Suffix
Dimensions shown in inches and (millimeters)
Rev. G | Page 15 of 16
070606-A
0.070 (1.78)
0.060 (1.52)
0.045 (1.14)
OP200
Data Sheet
10.50 (0.4134)
10.10 (0.3976)
9
16
7.60 (0.2992)
7.40 (0.2913)
10.65 (0.4193)
10.00 (0.3937)
8
1.27 (0.0500)
BSC
0.30 (0.0118)
0.10 (0.0039)
COPLANARITY
0.10
0.75 (0.0295)
45°
0.25 (0.0098)
2.65 (0.1043)
2.35 (0.0925)
SEATING
PLANE
0.51 (0.0201)
0.31 (0.0122)
8°
0°
0.33 (0.0130)
0.20 (0.0079)
1.27 (0.0500)
0.40 (0.0157)
COMPLIANT TO JEDEC STANDARDS MS-013-AA
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
03-27-2007-B
1
Figure 38. 16-Lead Standard Small Outline Package [SOIC_W]
Wide Body
(RW-16)
S-Suffix
Dimensions shown in millimeters and (inches)
ORDERING GUIDE
Model 1
OP200AZ
OP200EZ
OP200GPZ
OP200GSZ
OP200GSZ-REEL
1
TA = 25°C VOS Max (µV)
75
75
200
200
200
Temperature Range
−55°C to +125°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
The OP200GPZ, OP200GSZ, and OP200GSZ-REEL are RoHS Compliant Parts.
©1978–2017 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D00322-0-3/17(G)
Rev. G | Page 16 of 16
Package Description
8-Lead CERDIP
8-Lead CERDIP
8-Lead PDIP
16-Lead SOIC_W
16-Lead SOIC_W
Package Option
Z-Suffix (Q-8)
Z-Suffix (Q-8)
P-Suffix (N-8)
S-Suffix (RW-16)
S-Suffix (RW-16)
工商网监
湘ICP备2023018690号
