47-10320

NOTES: REVISIONS THIRD ANGLE PROJ. REV 1. INITIAL TOOL SETTING RQUIREMENTS: DESCRIPTION A WITH DIES FIRMLY AFFIXED IN TOOL ON THE DIE MOUNTING SURFACES, CLOSE THE TOOL FULLY (UNTIL THE RATCHET RELEASES) WITH 25-35 LBS,HAND FORCE THE DIES MUST BE 'BUTTED' (TOUCHING BOTH FRONT & REAR SURFACES). THE RATCHET ADJUSTER WHEEL SHOULD BE POSITIONED IN THE CENTER INDENT (+/- ONE INDENT POSITION) DATE RELEASE TO MFG. 05-Dec-14 ECO 2809 2. DO NOT SCALE THIS DRAWING. 3. REMOVE ALL BURRS, BREAK SHARP EDGES AND CORNERS 0.005 MAXIMUM, UNLESS OTHERWISE SPECIFIED. DIE SET 47-20253 SHOWN 4. UNLESS OTHERWISE SPECIFIED, ALL DIMENSIONS ARE AFTER PLATING. 5. THE DIE SETS MAY BE PURCHASED SEPARATELY (P/N PER TABLE BELOW). 6. PACKAGING: A. QUANTITY: B. PACKAGE MARKING: PART NUMBER (TOOL & DIE SET) 47-10070 SINGLE PACK AMPHENOL RF 47-10XXX (SEE TABLE) DATE CODE DIE SET PART NUMBER 47-20000 DIE SET OPENINGS IN INCHES (MM) (UNLESS OTHERWISE NOTED, ALL OPENINGS ARE HEXAGONAL) 0.068(1.73) 0.213(5.41) 0.255(6.48) - - - - 47-10150 47-20004 0.068(1.73) 0.128(3.25) 0.178(4.52) - 47-10090 47-20003 0.080(2.03) 0.100(2.54) 0.429(10.90) - 0.068(1.73) 0.255(6.48) 0.324(8.23) 0.190(4.82) 0.213(5.40) 47-10160 47-10230 47-10110 47-10120 47-10063 47-10100 47-10180 47-10200 47-10210 47-10220 47-10240 47-10250 47-10260 47-10270 47-10280 47-10290 47-10300 47-10310 47-10320 47-20008 47-20029 47-20001 47-20002 47-20245 47-20026 47-20025 47-20024 47-20027 47-20028 47-20030 47-20247 47-20249 47-20250 47-20251 47-20252 0.178(4.52) 0.100(2.54) 0.429(10.90) 0.042(1.07) 0.068(1.73) 0.042(1.07) 0.042(1.07) 0.255(6.48) 0.052(1.32) 0.178(4.52) 0.068(1.73) 0.320(8.13) 0.068(1.73) 0.324(8.23) 0.116(2.95) 0.429(10.90) 0.042(1.07) 0.068(1.73) 0.178(4.52) 0.106(2.70) 0.068(1.73) 0.042(1.07) 0.052(1.32) 0.052(1.32) 0.213(5.41) 0.213(5.41) 0.178(4.52) - 0.213(5.40) 0.350(8.88) - 0.100(2.54) 0.068(1.73) 0.114(2.90) 0.130(3.30) - 0.278(7.08) 0.429(10.90) 0.263(6.68) - 0.278(7.06) - - - 0.068(1.73) 0.068(1.73) - - 0.052(1.32) 0.100(2.54) - 0.255(6.48) 0.255(6.48) 0.255(6.48) - 0.213(5.41) - - - - 0.128(3.25) 0.178(4.52) - - - - - - - - 0.042 (1.07) SQ. 0.068(1.73) 0.178(4.52) 0.278(7.06) 0.255(6.48) - 0.324(8.23) 0.319(8.10) 0.255(6.48) 0.042(1.07) - 0.075(1.90) - 47-20254 47-20255 47-10350 47-20257 47-20256 0.178(4.52) 0.052(1.32) 0.429(10.90) 0.105(2.67) 0.187(4.75) 0.068(1.73) 0.075(1.90) 0.128(3.25) 0.042(1.07) 0.255(6.48) - 0.324(8.23) 0.151(3.84) UNLESS OTHERWISE SPECIFIED, DIMENSIONS ARE IN METRIC AND TOLERANCES ARE: