PT08E14-18S-027

AMPHENOL CORPORATION Amphenol Industrial Phone: 888-364-9011 191 Delaware Avenue Sidney, NY 13838-1395 www.amphenol-industrial.com Notice: Specifications are subject to change without notice. Contact your nearest Amphenol Corporation Sales Office for the latest specifications. All statements, information and data given herein are believed to be accurate and reliable but are presented without guarantee, warranty, or responsibility of any kind expressed or implied. Statements or suggestions concerning possible use of our products are made without representation or warranty that any such use is free of patent infringement and are not recommendations to infringe any patent. The user should not assume that all safety measures are indicated or that other measures may not be required. Specifications are typical and may not apply to all connectors. HKA 1-2016 Amphenol® 97 Series Connectors are UL recognized and CSA recognized. Amphenol ® PT Series Miniature Cylindrical Connectors 12-070-17 www.amphenol-industrial.com Amphenol® 97 Series Connectors are UL recognized and CSA recognized. Table of Contents Introduction, Amphenol® Miniature Cylindrical Page General Information, Design Flexibility . . . . . . . . . . . . . . . . . . . 1, 2 Connector Selection Guide . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Insert availability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4, 5 Alternate positioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Insert arrangement patterns . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-10 PT, SP, MS/PT Proprietary/MIL-DTL-26482, Series 1 Bayonet Coupling, Solder Contacts General Information, Specifications, Service Class . . . . . . . . . . . 11, 12 PT00 (MS3110), SP00 wall mounting receptacle . . . . . . . . . . . . . . 13 PT01 (MS3111) cable connecting receptacle . . . . . . . . . . . . . . . . 14 PT02 (MS3112) SP02 box mounting receptacle . . . . . . . . . . . . . . 15 PT06 (MS3116) SP06 straight plug . . . . . . . . . . . . . . . . . . . . . 16 PT07 (MS3114) SP07 jam nut receptacle . . . . . . . . . . . . . . . . . . 17 PT08E, SP08E 90 degree plug . . . . . . . . . . . . . . . . . . . . . . .  18 PT Connectors with Printed Circuit Board Contacts box mount receptacle, jam nut receptacle . . . . . . . . . . . . . . . . .  19 PTB, SPB thru bulkhead receptacle . . . . . . . . . . . . . . . . . . . . . 20 General Information, Specifications - PT hermetic . . . . . . . . . . . . . 21 PTIH (MS3113H) hermetic solder mounting receptacle . . . . . . . . . . . 22 PT02H hermetic box mounting receptacle . . . . . . . . . . . . . . . . . 23 PT07H (MS3114H) hermetic jam nut receptacle . . . . . . . . . . . . . . 24 PT, SP, MS/PT how to order . . . . . . . . . . . . . . . . . . . . . . . . . 25 PT-SE, SP-SE, MS/PT-SE Proprietary/MIL-DTL-26482, Series 1 If more information is needed concerning the con­nectors covered in this publication, or if there are special application needs, please contact: Amphenol Corporation Amphenol Industrial Operations 191 Delaware Avenue Sidney, New York 13838-1395 Telephone: 888-364-9011 Fax: 520-397-7169 Please go to the Amphenol websites to view, download and save this catalog and most all of Amphenol interconnection product literature. www.amphenol-industrial.com Some miniature connector styles are available in RoHS Compliant versions. Please contact Amphenol Industrial Operations for more information. Bayonet Coupling, Crimp Contacts General Information, Specifications, Service Class . . . . . . . . . . . 26, 27 PT00SE (MS3120), SP00SE wall mounting receptacle . . . . . . . . . . . 28 MF00SE (MS3128) wall mounting receptacle . . . . . . . . . . . . . . . . 29 PT01SE (MS3121) SP01SE cable connecting receptacle . . . . . . . . . 30 PT02SE (MS3122) SP02SE box mounting receptacle . . . . . . . . . . . 31 MF02SE (MS3127) box mounting receptacle . . . . . . . . . . . . . . . . 32 PT06SE (MS3126), SP06SE straight plug . . . . . . . . . . . . . . . . . 33 PT07SE (MS3124) SP07SE jam nut receptacle . . . . . . . . . . . . . . 34 PT08SE, SP08SE 90 degree plug . . . . . . . . . . . . . . . . . . . . . 35 PT-SE, SP-SE, MS/PT-SE how to order . . . . . . . . . . . . . . . . . . 36 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37-40 Glands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Application tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Contacts, Power and Thermocouple Crimp . . . . . . . . . . . . . . . . . . . . 43 Contacts, Shielded Coax . . . . . . . . . . . . . . . . . . . . . . . . . . . 44-48 Mounting Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Other Amphenol Miniature Cylindrical Connectors . . . . . . . . . . . . . . . . 50 Proprietary/MIL-DTL-26482 Series 1 connectors covered in this catalog are widely used in gen­eral duty and environmental applications, both industrial and military. Markets that use this family of connectors include: • Instrumentation • Monitoring Equipment • Machine Tool, Factory Automation • Communications • Geophysical • Industrial Controls and Robotics • Oil and Petrochemical Industries • Rail/Mass Transit • Military/Aerospace Amphenol operates Quality Systems that are cer­tified to ISO9001: 2008 by third party registrars. NOTE: The connector products in this brochure were formerly known as Bendix® products. These products are now manufactured and sold under the Amphenol® brand name. The name “Amphenol” will replace the name “Bendix” on products and literature in the future. NOTE: The Miniature MIL-DTL-26482, Series 2 connectors PTS-DR and MS/PTS-DR (formerly in this catalog) are no longer supplied with these designations. Amphenol now supplies the Amphenol®/Matrix® MIL-DTL-26482, Series 2. (Military numbers include MS3470 - MS3472, MS3474, - MS3476). Amphenol ® Miniature Cylindrical Connectors Proprietary/MIL-DTL-26482, Series 1 Amphenol® Miniature Cylindrical connectors offer twice the number of contacts in just half the size of a Standard connector. These miniature connectors, are available in several series, each with varying design characteristics and customer options to meet cost con­siderations and provide maximum design flexibility. There are two styles within the family that are MS approved and qualified to MIL-DTL-26482, Series 1, and in addition there are several proprietary styles. Common features of all styles: • All are for general duty applications and environmental sealing is achieved with the grommet and clamp design. • Operating temperature is from –55°C to +125°; Operating voltage to 1000 VAC (RMS) at sea level. • Pin and socket contacts are machined from low loss copper alloy and gold plated to eliminate contact corrosion and provide an indefinite shelf life. • All have resilient inserts which provide high dielectric strength and moisture barrier. • A variety of shell finishes (including non-cadmium) and a variety of backend accessories are available within the styles. Bayonet Coupling with Solder Contact Termination PT Solder jam nut receptacle and mated straight plug PT, MS/PT (solder) • MS and proprietary versions • Factory installed solder contacts • 3 point bayonet coupling and 5 key/keyway mating. • Intermateable with all miniature series connectors. • MS/PT meets MIL-DTL-26482 Series 1, service classes E, F and P. • MS/PT is UL recognized. SP (solder) • SP Series is a modification of the PT with same features except a wider flange for back panel mounting Options • 7 shell styles with 60 insert patterns • Hermetic seal (glass fusion) recepta­cle styles available • Pressurized thru bulkhead recepta­cle style available • Pre-installed coax solder contacts are available • Printed circuit board contacts are available Bayonet Coupling with Crimp Contact Termination PT Solder wall mount receptacle PT-SE, MS/PT-SE (crimp) • MS and proprietary versions • Crimp rear insertable/front release contact termination. (closed entry socket insert prevents probe damage). • 3 point bayonet coupling and 5 key/keyway mating. • Intermateable with all miniature series connectors. • MS/PT-SE meets MIL-DTL-26482 Series 1, service classes E, F, P. SP-SE (crimp) • Modification of the PT-SE with wider flange for back panel mounting PT-SE Crimp wall mount receptacle and mated straight plug 1 Options • 6 shell styles with 47 insert patterns • Coax and thermocouple contacts are available Amphenol ® Miniature Cylindrical design flexibility The large family of miniature proprietary and MS style connectors provides for many optional features and designs. In addition to the choices of bayonet or threaded shells, solder or crimp termination within the style variations, there are additional options that are shown here. Hermetics Hermetically sealed receptacles have fused compression glass sealed inserts which provide envionrmental moisture sealing. There are three hermetic styles within the PT bayonet series. Coaxial Contacts Amphenol Miniature connectors can incorporate shielded coax contacts. Size 8 and 12 crimp coax contacts are available in PT-SE, SP-SE, MS/PT-SE. Factory installed size 8 and 12 solder type coax contacts are available in PT, SP,MS/PT connectors. See coax contact information pages at the end of this catalog. PT Connector with Hermetic Seal Insert and Coax Contacts PT Connector with PC Tail Contacts Printed Circuit Board Tail Contacts PT bayonet connectors in box mounting receptacle and jam nut receptacle styles are avail­able with printed circuit board contacts. Standard PCB tails for MIL-DTL-26482 connectors have gold plating, .0050 inches over nickel. See page 20 and call Amphenol for further infor­mation. Flex Circuitry Flex termination assemblies for attaching cylindrical connectors to printed circuit boards are available through the Amphenol division ACT, Advanced Circuit Technology. Flex can be used with miniature 26482 connectors and it can be designed to meet specific length, current carrying capacity and to fit the precise geometric shape of the connector to board package. Flex circuity plugs into a printed circuit board and creates a self-locking terminal pad which eliminates the need for an additional interconnect to the PCB. PT Connector with Flex Filter Protection Amphenol offers the FPT Series which combines the miniature PT series with an EMI filter. Designed to provide EMI protection for sensitive circuits, each circuit is individually filtered within the con­nector, eliminating the need for costly and bulky exterior network filters. Filter contacts are available in MF, HF, VHF, and UHF ranges and are intermateable and intermountable with MIL-DTL-26482 con­nectors. For further information see catalog 12-120, Amphenol EMI Filter Transient Protection Connectors. PT Connector with EMI Filter Protection Overmolded Cable Overmold seals and cables can be designed for almost any industrial application. A variety of materials are available: neoprene, hypalon and others; and a variety of lengths can be designed to meet customer specifications. Overmold seals to the rear of the connector and to the cable jacket providing moisture sealing. PT Connector with Overmolded Cable 2 Amphenol ® Miniature Cylindrical connector selection guide The accompanying chart is provided to assist the user in selecting the appropriate type of miniature connector to meet the application requirements. Further information can be found in specific sections of this catalog. Solder CHARACTERISTICS Intermateable† Contacts PT MS/PT SP o o o o o • • • • • • • • • • • • • • • **• • **• • • • Solder Crimp MS/ PT-SE • • Crimp RI/FR Contact Retention System Non-Removable Coupling Bayonet Standard Finishes†† Olive Drab Cadmium (003) Removable Anodic Coated (005) Temperature Range Resilient Dielectric (–55°C to +125°C) Wide Mounting Flange Hermetic Seal • • • • • • • • • • • • • • *• • *• • *• • • • • • *• • • • • PT-SE SHELL STYLE AVAILABILITY Wall Mounting Receptacle “00” Cable Connecting Receptacle “01” *** Box Mounting Receptacle “02” Straight Plug “06” Jam Nut Receptacle “07” Thru-bulkhead Receptacle “TB” Solder Mount Receptacle “I” 90° Plug “08” RI/FR  =  Rear Insertion/Front Releasable † o intermates with o †† Optional finishes available. See “how to order” sections. * Available in hermetic version ** Dual mounting holes *** This connector style is sometimes referred to as a cable connecting “plug.” It does, however, mate with either a straight or 90 degree plug. 3 *• • • • • • • • Amphenol ® Miniature Cylindrical insert availability Solder Termination Insert Arrangement MS/PT   6-1 Crimp Termination PT SP Hermetic PT MS-PT MS/PT-SE PT-SE SP-SE Contact Size Coax Total Contacts 20 16 12 12 8 Service Rating X X X* 1 1 I   8-2 X X X X 2 2 I   8-3 X X X X 3 3 I   8-4 X X X X 4 4 I   8-33 X X X X 3 3 I   8-98 X X 3 3 10-2 X X 2 10-5 X X X* X X X X X 10-6 X 10-70 X I 2 5 5 6 6 I I I 1 10-98 X X X X* 12-3 X X X X 12-4 X 6 X 1 6 3 I 3 II 4 I X X X* 12-8 X X X X* X 8 8 I 12-10 X X X X X 10 10 I 12-14 X X 14 14 I 12-98 X X 10 10 14-2 X X 2 S S X X X X X 5 14-4 14-5 X 14-8 4 Coax I 2 4 II 4 I 5 II X X 8 6 14-12 X X X X X 12 8 4 I 14-15 X X X X X 15 14 1 I 14-18 X X X X* X 18 18 14-19 X X X X X 19 19 X* 5 1 14-22 14-71 P X 14-91 HV S X 14-AA 4 X* X X X 16-8 X X X X 16-23 X X X 16-26 X X X X X 16-70 X 16-76††† 16-99 X 18-5 3 2 I I 4 3 4 8 X 23 22 X 26 26 15 14 X* 14 8 21 X X 23 X X* 5 18-8 X X X X X 11 18-30 X X X X* X 30    *Not available in MS version   **Flashover voltage 5,000 VAC (RMS)   ***1500 VAC (RMS) S designates Socket insert only. I II 1 I I 1 2 1 N/A 5 *** I 5 8 29 I 8 8 18-11 1 ** 4 X I 3 X X I II I 11 II 1 I P designates Pin insert only.    †Size 12 contacts for #10 wire   ††Not presently tooled †††Contacts must be ordered separately 4 Amphenol ® Miniature Cylindrical insert availability, cont. Solder Termination Insert Arrangement MS/PT 18-32 X Crimp Termination PT SP Hermetic PT MS-PT X X X 18-71 Contact Size Coax MS/PT-SE PT-SE SP-SE Total Contacts X 32 X* 9 18-72 X X 14 18-75 X X 4 X X 18-76 20 16 12 18-91 HV I 8 10 6 X* 6 6 X 16 1 Coax, II 4 Coax 4 N/A 3 8 Service Rating 1 II 2 Coax, I ** 20-16 X X X 20-24 X X X 24 24 I X X 25 25 I 20-25 20-26 X 8 32 4 18-80 12 16 X X 26 20 20-27 X X X 27 27 20-39 X X X X X 39 37 20-41 X X X X X 41 41 14 10 7 7 20-70 20-90 HV X X 22-7 X X X X X X X X 22-34 X 22-36 22-21 6 I I 2 I I 4 Coax Hi-Voltage X* 7 X 21 X* 25 X 32 32 I X 34 34 I X X 36 36 X 22-25 22-32 II 7 Coax 21 II 25 I I 22-41 X X X X X 41 27 22-55 X X X X X 55 55 X X 19 13 6 I, Coax 9 2 7 I, Coax 19 12 22-70 22-71 22-72 X X 22-78††† X* 22-96 X 24-61 24-71 X X X X X 4 51 47 X 61 61 49 45 6 1    *Not available in MS version   **Flashover voltage 5,000 VAC (RMS)   ***1500 VAC (RMS) N/A 7 Coax II 31 X* 24-79 3 7† 31 X I 7 X 24-51 I 7 X* 24-31 14 I 4 I I 2 2 N/A 5 Coax    †Size 12 contacts for #10 wire   ††Not presently tooled †††Contacts must be ordered separately 5 Amphenol ® Miniature Cylindrical alternate positioning A B A B Position W Position X Views looking into front face of pin insert or rear of socket insert. Insert Rotation Shell Size 6 8 8 8 8 8 10 10 10 10 10 12 12 12 12 12 12 14 14 14 14 14 14 14 14 14 14 14 14 16 16 16 16 16 16 18 18 Insert Arrangement   6-1   8-2*   8-3   8-4*   8-33*   8-98 10-2 10-5* 10-6* 10-70 10-98* 12-3* 12-4* 12-8 12-10* 12-14 12-98* 14-2 14-4* 14-5* 14-8 14-12* 14-15* 14-18* 14-19* 14-22 14-71 14-91HV 14-AA* 16-8* 16-23 16-26* 16-70 16-76 16-99* 18-5 18-8 – 58 60 45 90 – 45 45 90 – 90 – 38 90 60 – 61 58 45 40 48 43 17 15 30 45 – – 45 54 158 60 41 – 66 55 180 Position Y Position Z Insert Rotation Degrees W A B A To avoid cross-plugging problems in applications requiring the use of more than one miniature cylindrical connector of the same size and arrangement, alternate insert rotations are available as indicated in the accompanying chart. As shown in the diagram at right, the front face of the pin insert is rotated within the shell in a clockwise direction from the normal shell key. The socket insert would be rotated counterclockwise the same number of degrees in respect to the normal shell key. B Alternate Positioning X – 122 210 97 – – 90 151 – – 180 – – 112 155 – 135 122 – 92 162 90 110 90 165 – – 60 – 152 270 – 122 – 156 97 – Y – – – 184 – – 315 180 – – 240 180 – 203 270 – 189 – – 184 189 – 155 180 315 – – – – 180 – 275 216 – 223 263 – Shell Size Z – – – – – – – 270 – – 270 – – 292 295 – 340 – – 273 312 – 234 270 – – – – – 331 – 338 286 – 340 315 – 18 18 18 18 18 18 18 18 18 20 20 20 20 20 20 20 20 20 22 22 22 22 22 22 22 22 22 22 22 22 22 24 24 24 24 24 Insert Arrangement 18-11* 18-30* 18-32* 18-71 18-72 18-75 18-76 18-80 18-91HV 20-16* 20-24 20-25 20-26 20-27 20-39* 20-41* 20-70 20-90 22-7 22-21* 22-25 22-32 22-34 22-36 22-41 22-55* 22-70 22-71 22-72 22-78 22-96* 24-31 24-51 24-61* 24-71 24-79 Degrees W 62 180 85 18 53 45 – 45 90 238 70 72 13 72 63 45 63 45 19 16 60 72 62 72 39 30 30 33 42 19 19 90 22 90 39 – X 119 193 138 108 102 – – 90 180 318 145 144 107 144 144 126 135 135 41 135 125 145 142 144 135 142 82 191 200 41 41 225 171 180 131 – Y 241 285 222 127 213 – – 135 240 333 215 216 210 216 252 225 222 225 – 175 211 215 218 216 264 226 218 236 277 – – 255 313 270 205 – Z 340 350 265 215 293 – – 160 270 347 290 288 322 288 333 – 335 315 – 349 336 288 298 288 – 314 312 270 339 – – – – 324 281 – *  Available in Hermetic Class 6 Amphenol ® Miniature Cylindrical insert arrangements front face of pin inserts illustrated C A B D A B A B C A C C B A B B A Insert Arrangement 6-1 8-2 8-3 8-4 8-33 8-98 10-2 Service Rating I I I I I I I Number of Contacts 1 2 3 4 3 3 2 Contact Size 20 20 20 20 20 20 16 E D C D A A E B E B C A F A F D B C A C G D B H E C B A F B C D Insert Arrangement 10-5 10-6 10-70 10-98 12-3 12-4 12-8 Service Rating I I Coax I II I I Number of Contacts 5 6 1 6 3 4 8 Contact Size 20 20 8 Coax 20 16 16 20 H A B G K F A J C D J E D B E K N A C F H L M P A H G R F K B C J E D D A C B A E D B C H B F D G C E Insert Arrangement 12-10 12-14 12-98 14-2 14-4 14-5 14-8 Service Rating I I I II I II I Number of Contacts 10 14 10 2 4 5 6 2 Contact Size 20 20 20 12 12 16 20 12 H G J A B M K F E L C D K J L A M R H B N C D P G F E K J T H L A M N U S G R F P E C D A M L B N K J P V U R T H S G F A B C B E D E D D A A B C C B C Insert Arrangement 14-12 14-15 14-18 14-19 14-22 14-71 14-91HV Flashover Service Rating I I I I I I 5,000 VAC (RMS) Number of Contacts 8 4 14 1 18 19 1 4 3 1 3 Contact Size 20 16 20 16 20 20 20 12 16 8 Coax 20 7 Amphenol ®® Miniature Cylindrical Cylindrical Amphenol  insert arrangements front face of pin inserts illustrated A A D L H C C E 14-AA 16-8 Number of Contacts 4 8 I Contact Size A N J L P H P B N C M D M G L E Number of Contacts Contact Size 16-76 8 5 20 12* 2 Coax* 21 20 Y K I W X J 16-23 H E J E G 20 N/A 20 V E D A H F C B K H C 1 12 Coax J B B D L 14 G E D K 16-70 26 16 C R M F I 1 B N F 16-26 A C U L G C F G I L E V H G D c Z F G 20 T H V 22 W J U W H E 16-99 Flashover 1.500 VAC (RMS) 1 J B Z X K F Service Rating Y S M T A P C U b A A R C B T N a D 16 K Z A R S P B S X II 12 A R Y K D Insert Arrangement Service Rating Insert Arrangement M B F B P N G 16 D E 18-5 18-8 18-11 5 8 11 II 2 F D I 12 II 12 16 *Contact Positions Optional R P S A d B T c U e b N Z L K Insert Arrangement V f g a M E W X Y F G H J P D N M Number of Contacts 29 Contact Size I 20 A V f c g h b a K Z H J C C E F E 32 8 20 Contact Size 4 A G C F E B B D D E Number of Contacts N/A B F Service Rating E 20 12 Coax A C Insert Arrangement 10 8 Coax H B D 18-72 1 16 C N F 18-71 II, Coax A C G D A D B M H F G D A L J P I 16 K G 18-32 1 B J D X Y A H B W j 18-30 Service Rating U e d L T S R C 18-75 Coax 4 8 Coax 18-76 3 II 18-80 1 12 Coax 8 Coax 89 I, Coax 6 20 2 8 Coax C 18-91 HV Flashover 5,000 VAC (RMS) 6 20 Amphenol ®® Miniature Cylindrical Cylindrical Amphenol  insert arrangements front face of pin inserts illustrated L A K L B M K N S C J H D H G F a T G S 20-25 Number of Contacts 16 24 25 I 16 N b L c X K R P F H 20-27 Number of Contacts 27 i g k Z m q d e M L b c H J K U D F g R f P N 20-39 37 20 I 20 p e d F 10 C P X D U J 20-90 Number of Contacts J F 7 21 25 8 Coax N M A P a B j g Z K C d D e f Y T P N k H W G V F E X h M e F N G Z L K J H V g m d M k c L b K Y Z a G H J 22-34 22-36 Number of Contacts 32 34 36 Contact Size I 20 20 10 9 I 20 U E T B C a E c t q d g G e H f R P F p r h D b n s S F A m i D X Z k j V W j l W C h 22-32 I X B Insert Arrangement Service Rating Y A n Y a 16 U f W g j P D f l R C E b U X V T S B U e c I 16 d R S c h II A T S R L J 22-25 20 b G H 22-21 Coax Contact Size E 22-7 Hi-Voltage 7 D U E G Insert Arrangement a V F H Service Rating C T W K T B S Z b L S D C D Y C A R M R 4 8 Coax N B V K E Coax 20 X E D N 20-70 W L G E C G A B B M J K A L H H P A 6 12 G b c L N M B G P F 20 A F a 41 F G m q E Z I 16 E F J I J D 20-41 2 D H Y K C Y n M b X 20 t r c Z C 20-26 B X W 20 k s h S G j i T E A W V C a n p f I Contact Size B Y r h N G Insert Arrangement Service Rating S E U V W J D T d Y T A X j a K 20 W V U C S Z M B a B L I 20 A R P M H J 20-24 Contact Size F G K 20-16 II P A V T N U a Insert Arrangement Service Rating R E Z V D S D T b C E F U C Y L R B S X W M P Z P N B Y U E N X V J P R W A R A M J N M L 22-41 27 20 I 14 16 K Amphenol ®® Miniature Cylindrical Cylindrical Amphenol  insert arrangements front face of pin inserts illustrated k R m j N i B V n X q BB HH y FF DD h L w v f e Insert Arrangement 22-55 Number of Contacts 55 Service Rating E T K N G R H E F 22-70 13 20 2 8 Coax N B F Y K a J b g c d C H Insert Arrangement 22-78 22-96 24-31 Number of Contacts 7 7 31 Coax 8 Coax W v GG s r U q T PP MM EE p S LL DD n R P CC BB m k N M 24-61 Number of Contacts 61 W E F g z G h AA Insert Arrangement Contact Size f y H i j J u d f m x S R K L D E k P v w j N M h i L 45 20 20 N/A 2 16 E C B H J K 24-71 I A F g G n T 20 F e p U 47 D AA BB 24-79 2 1 8 Coax Coax 20 Symbol 5 8 Coax Contact Legend Contact Size 20 16 12 HV 12 Coax 8 Coax 11 10 P h i m j k I 4 H J K L M N G g w n F f 24-51 C c BB z x R E e v CC S B b z y r q V A t s X D e x KK Y C d JJ NN a Z B D d AA DD 16 # 10 wire C c y I 12 for w HH FF V Service Rating II B p T F D D u q E U G t r U T u s V D S A b t W C R e W X 3 8 Coax a Z Q f X C 16 Y P V E E N/A 4 20 B Z E X M D F A L G c N 12 8 Coax M A C 22-72 7 20 A b P 22-71 I, Coax 6 G a T D I, Coax B Z U G C G F Y L V E R H A Contact Size B S J G D P S 20 Service Rating K B C V J I Contact Size A J F H J K U L b c d D a t u g M H B F Z s EE x M Y r CC GG A A C W p AA z P A U T S 12 Coax Amphenol ® PT, SP, MS/PT Proprietary/MIL-DTL-26482, Series 1 bayonet coupling and solder termination wall mounting receptacle cable connecting receptacle* Amphenol® solder contact miniature cylindrical connectors meet the most critical application needs. Design versatility combined with high reliability performance makes these series of Miniature Cylindrical Connectors ideal for environ­mental sealing or pressurized applications. The MS/PT Series is qualified to MIL-DTL-26482, Series 1 and has all the outstanding design characteristics and quality of the PT Series. The SP Series is a modification of the PT, providing special shells with a wide mounting flange for back panel mounting. A corrosion resistant electrically conductive finish of cadmium plate with an olive drab chromate after-treatment is used on the PT and MS/PT. The SP is given a durable non-conductive hard anodic “Alumilite”® coating which provides abrasion protection and resis­tance to corrosion. **NEW** 500 hour corrosion resistance, RoHS compliant harsh environment conductive plating. Gray Zinc over an Electroless Nickel (Gray ZnNi) base, with a Light Gun Metal Gray appearance. box mounting receptacle Shell components for these series are aluminum. The dependable 5 key/keyway polarization with bayonet lock coupling assures pos­itive mating with no chance of cross plugging. Spring tension pro­vided by a wave washer in the coupling nut ensures maintenance of interfacial seal between mating halves. Both the insert and main joint gasket are molded from resilient neoprene. This provides excellent moisture sealing at the gasket and superior electrical isolation of the contact in the insert. straight plug jam nut receptacle Both pins and sockets are machined from a copper alloy and are gold plated. This gold plating eliminates contact corrosion and offers an indefinite shelf life. Socket contacts for these series are a closed entry design. A breakaway style plug is available in the PT solder series. Hermetics receptacles are available in PT and MS/PT solder series. Receptacles with printed circuit board contacts are also available. PT Solder is UL recognized under file #E115497, Vol. 1, Sec. 5. The PT, SP and MS/PT Series are intermateable and intermount­able with all existing Miniature Cylindrical Series connectors. Refer to pages 4-10 for insert arrangement availability. PT, SP, MS/PT Table 1: CONTACT DATA/CONNECTOR RATINGS Contact Specifications thru bulkhead receptacle Contact Size Test Current Maximum Millivolt Drop† Solder Well Diameter Solder Well Depth .046 +.004 –.000 .125 +.031 –.000 20 7.5 55 16 13.0 50 12 23.0 42 .078 +.005 –.003 +.004 .116 –.002 .188 +.031 –.000 +.031 .188 –.000 Service Rating Recommended Operating AC Voltage at Sea Level Sea Level 50,000 ft. 70,000 ft. 110,000 ft. I 600 1,500 500 375 200 II 1,000 2,300 750 500 200 Service Rating 11 Test Voltage AC (RMS), 60 cps † Silver plated wire per MILDTL-26482 * This connector style is sometimes referred to as a cable connecting “plug.” It does, however, mate with a straight or 90 degree plug. PT, SP Service Classes PT and SP connectors are available in the service classes listed below. Each class, with the exception of hermetic, offers one or more means of terminating or supporting a cable or wire bundle. “A” “A” general duty General duty; back shell is threaded for con­ duit attachment of MS3057 cable clamp “A” (SR) General duty, with strain relief clamp for cable or wire bundle support “C” “E” Pressurized receptacle; less than 1 cu. in. per hour leakage at 30 psi over a tempera­ture range of  –65°F to +257°F Environmental resistant connectors - sup­ plied with a multi-holed grommet and clamp­ ing nut for moisture-proofing individual open wires “E” (SR), MS / “F” strain relief “E” (SR) Environmental resistant strain relief clamp and grommet for moisture proofing individual wires; provides added wire bundle support “P” Translucent nylon boot for retaining cus­ tomer-applied potting compounds; held in place by a threaded ring “P” (SR) Strain relief clamp suitable for retaining cus­ tomer applied potting compounds, with pro­ vision for wire support “PG” “H”* “E”, MS / “E” open wire seal Compressing cable gland for moisture proofing jacketed cables. Hermetically sealed with compression glass inserts (see pages 22-25) Style with printed circuit board contacts- see page 20. MS/PT Service Classes “P”, MS / “P” potting boot The MS/PT Miniature connector is available in the fol­lowing certified service classes: “E” Environmental resistant connectors - sup­ plied with a multi-holed grommet and clamp­ ing nut for moisture-proofing individual open wires “F” “J” “P” Grommet seal with strain relief clamp Compressing clamp and neoprene gland for moisture proofing multi-conductor jacketed cable and strain relief. Telescoping sleeves (MS 3420A) can be used to adapt to cables smaller than minimum close-down. “PG” cable gland seal Translucent nylon boot for retaining cus­ tomer-applied potting compounds; held in place by a threaded ring 12 PT00 (MS3110) SP00 wall mounting receptacle S R PT .120 ± .005 Dia. (.147 ± .005 Dia., size 24) SP .150 ± .005 Dia. (TP) M 4 Holes R S L Q A (TP) “PG” Cable Gland Seal K TERMINATION ASSEMBLIES “A” General Duty/ “C” Pressurized“ L L Z “A” (SR), “E” (SR), “P” (SR), MS / “F” Strain Relief “E” Open Wire Seal L V “P” Potting Boot N L L D PT00PG-XX-XXX N GDH N D PT00A-XX-XXX (SR) SP00A-XX-XXX (SR) PT00E-XX-XXX (SR) SP00E-XX-XXX (SR) PT00P-XX-XXX (SR) SP00P-XX-XXX (SR) MS3110F-XX-XXX To complete part number see how to order on page 25. n (MMC) located within  .0025 of (TP) Receptacle Front View R S (TP) Max. PT SP PT SP .469 .594 .719 .812 .906 .969 1.062 1.156 1.250 1.375 .641 .734 .812 .938 1.031 1.125 1.203 1.297 1.375 1.500 .688 .812 .938 1.031 1.125 1.219 1.312 1.438 1.562 1.688 .953 1.047 1.125 1.250 1.344 1.438 1.516 1.672 1.750 1.875 A +.001 –.005 .348 .473 .590 .750 .875 1.000 1.125 1.250 1.375 1.500 K +.020 –.010 PT SP .493 .493 .493 .493 .493 .493 .493 .650 .650 .683 6 8 10 12 14 16 18 20 22 24 – 6-32 6-32 6-32 6-32 6-32 8-32 8-32 8-32 8-32 D Min. – .240 .302 .428 .552 .615 .740 .740 .928 .990 G Max. – .125 .188 .312 .375 .500 .625 .625 .750 .800 H Max. – .812 .875 1.000 1.125 1.188 1.438 1.438 1.625 1.719 L Max. – 1.922 1.922 1.922 1.922 2.047 2.078 2.344 2.344 2.406 PT00E-XX-XXX SP00E-XX-XXX MS3110E-XX-XXX N Max. – .550 .675 .803 .920 1.047 1.165 1.290 1.418 1.543 PT00P-XX-XXX SP00P-XX-XXX MS3110P-XX-XXX PURC N D RELEASED / Dec . 21 2015, 2:09:12 PM MS3110J-XX-XXX Receptacle Side View M +.010 Q    –.000 L Thread Max. PT SP Class 2A .524 .906 .524 .906 .524 .906 .524 .906 .524 .906 .524 .906 .524 .906 .650 1.125 .650 1.125 .683 1.188 Class “A” (SR), “E” (SR), “P” (SR), MS / “F” Shell C Size Thread “J” Cable Seal XL PT00A-XX-XXX SP00A-XX-XXX PT00C-XX-XXX 6 8 10 12 14 16 18 20 22 24 D C .375 MIN Shell Size N N .431 .431 .431 .431 .431 .431 .431 .556 .556 .589 Class “E”, MS / “E” L Max. 1.266 1.266 1.266 1.266 1.266 1.266 1.266 1.516 1.516 1.578 N Max. .440 .560 .685 .813 .930 1.057 1.175 1.301 1.430 1.555 .462 .462 .462 .462 .462 .462 .462 .556 .556 .589   .3125-32 NEF   .4375-28 UNEF   .5625-24 NEF   .6875-24 NEF   .8125-20 UNEF   .9375-20 UNEF 1.0625-18 NEF 1.1875-18 NEF 1.3125-18 NEF 1.4375-18 NEF Class “P”, MS / “P” D Min. .192 .317 .434 .548 .673 .798 .899 1.024 1.149 1.274 All dimensions for reference only. 13 L Max. 1.438 1.438 1.438 1.438 1.438 1.438 1.438 1.656 1.656 1.717 N Max. .484 .608 .734 .858 .984 1.110 1.234 1.360 1.484 1.610 Z Max. PT SP .468 .468 .468 .468 .468 .468 .531 .531 .531 .498 Class “A”, “C” D Min. N Max. .438 .175 1.553 .462 .438 .297 1.553 .590 .438 .421 1.553 .717 .438 .546 1.553 .834 .438 .663 1.553 .970 .438 .787 1.553 1.088 .438 .879 1.553 1.216 .531 1.014 1.703 1.332 .531 1.134 1.703 1.460 .498 1.259 1.765 1.585 Class “J” D N Closed Free Max. – .168 .205 .338 .416 .550 .600 .635 .670 .740 L Max. – .230 .312 .442 .539 .616 .672 .747 .846 .894 – .547 .675 .812 .940 1.067 1.194 1.322 1.449 1.576 XL Max. – 2.271 2.271 2.411 2.599 2.943 3.172 3.610 3.766 3.985 V Thread Class A   .3750-32 NEF   .5000-28 UNEF   .6250-24 NEF   .7500-20 UNEF   .8750-20 UNEF 1.0000-20 UNEF 1.1875-18 NEF 1.1875-18 NEF 1.4375-18 NEF 1.4375-18 NEF Class “PG” B Thread – M12x1.5-6H M16x1.5-6H M16x1.5-6H M18x1.5-6H M22x1.5-6H M25x1.5-6H M25x1.5-6H M32x1.5-6H M32x1.5-6H L Max. – .936 .936 .936 .936 .936 .936 1.180 1.180 1.180 PT01 (MS3111) cable connecting receptacle L S Y S Q M A “PG” Cable Gland Seal K TERMINATION ASSEMBLIES “A” General Duty “A” (SR), “E” (SR), “P” (SR), MS / “F” Strain Relief L N Z “E” Open Wire Seal L V L “P” Potting Boot N L L PT01PG-XX-XXX D GD H N N N D “J” Cable Seal XL C .375 MIN PURCHA PT01A-XX-XXX (SR) PT01E-XX-XXX (SR) PT01P-XX-XXX (SR) MS3111F-XX-XXX PT01A-XX-XXX PT01E-XX-XXX MS3111E-XX-XXX PT01P-XX-XXX MS3111P-XX-XXX N Recept. Front View 6 8 10 12 14 16 18 20 22 24 S ±.020 .688 .812 .938 1.031 1.125 1.219 1.312 1.438 1.562 1.688 Y ±.020 .812 .938 1.062 1.156 1.250 1.344 1.438 1.562 1.688 1.812 A +.001 –.005 .348 .473 .590 .750 .875 1.000 1.125 1.250 1.375 1.500 K +.020 –.010 .494 .494 .494 .494 .494 .494 .494 .650 .650 .683 Class “A” (SR), “E” (SR), “P” (SR), MS / “F” Shell C Size Thread 6 8 10 12 14 16 18 20 22 24 – 6-32 6-32 6-32 6-32 6-32 8-32 8-32 8-32 8-32 D Min. – .240 .302 .428 .552 .615 .740 .740 .928 .990 G Max. – .125 .188 .312 .375 .500 .625 .625 .750 .800 H Max. – .812 .875 1.000 1.125 1.188 1.438 1.438 1.625 1.719 L Max. – 1.922 1.922 1.922 1.922 2.047 2.078 2.344 2.344 2.406 MS3111-XX-XXX Receptacle Side View M Q L +.016 Thread Max.  –.000 Class 2A .906 .906 .906 .906 .906 .906 .906 1.125 1.125 1.188 N Max. – .550 .675 .803 .920 1.047 1.165 1.290 1.418 1.543 .400 .400 .400 .400 .400 .400 .400 .535 .535 .568   .3125-32 NEF   .4375-28 UNEF   .5625-24 NEF   .6875-24 NEF   .8125-20 UNEF   .9375-20 UNEF 1.0625-18 NEF 1.1875-18 NEF 1.3125-18 NEF 1.4375-18 NEF Class “E”, MS / “E” L Max. 1.266 1.266 1.266 1.266 1.266 1.266 1.266 1.516 1.516 1.578 D RELEASED / Dec . 21 2015, 2:09:12 PM Note: This connector style is sometimes referred to as a cable connecting “plug”. It does, however, mate with either a straight or 90 degree plug. To complete part number see how to order on page 25. Shell Size D N Max. .440 .560 .685 .813 .930 1.057 1.175 1.301 1.430 1.555 Class “A”, Z Max. .948 .948 .948 .948 .948 .948 .948 1.166 1.166 1.166 Class “P”, MS / “P” D Min. .192 .317 .434 .548 .673 .798 .899 1.024 1.149 1.274 All dimensions for reference only. 14 L Max. 1.438 1.438 1.438 1.438 1.438 1.438 1.438 1.656 1.656 1.717 N Max. .484 .608 .734 .858 .984 1.110 1.234 1.360 1.484 1.610 D Min. .175 .297 .421 .546 .663 .787 .879 1.041 1.135 1.259 L Max. 1.553 1.553 1.553 1.553 1.553 1.553 1.553 1.703 1.703 1.765 Class “J” D N Closed Free Max. – .168 .205 .338 .416 .550 .600 .635 .670 .740 – .230 .312 .442 .539 .616 .672 .747 .846 .894 – .547 .675 .812 .940 1.067 1.194 1.322 1.449 1.576 N Max. .462 .590 .717 .834 .970 1.088 1.216 1.332 1.460 1.585 XL Max. – 2.271 2.271 2.411 2.599 2.943 3.172 3.610 3.766 3.985 V Thread Class A   .3750-32 NEF   .5000-28 UNEF   .6250-24 NEF   .7500-20 UNEF   .8750-20 UNEF 1.0000-20 UNEF 1.1875-18 NEF 1.1875-18 NEF 1.4375-18 NEF 1.4375-18 NEF Class “PG” B Thread – M12x1.5-6H M16x1.5-6H M16x1.5-6H M18x1.5-6H M22x1.5-6H M25x1.5-6H M25x1.5-6H M32x1.5-6H M32x1.5-6H L Max. – .936 .936 .936 .936 .936 .936 1.180 1.180 1.180 PT02 (MS3112) SP02 box mounting receptacle S R (TP) PT .120 ± .005 Dia. (.147 ± .005 Dia., size 24) L M SP .150 ± .005 Dia. R S (TP) 4 Holes A N K Z PT02A-XX-XXX SP02A-XX-XXX * PT02C-XX-XXX * SP02C-XX-XXX * PT02E-XX-XXX * SP02E-XX-XXX MS3112E-XX-XXX * PT02P-XX-XXX * SP02P-XX-XXX MS3112P-XX-XXX To complete part number see how to order on page 25. n (MMC) located within  .0025 of (TP) * The PT02 and SP02 box mounting receptacles are made only to complete a series; no provision is made for accessories or potting on the rear skirt. Receptacle Front View R (TP) Receptacle Side View K +.020 –.010 Shell Size PT SP PT SP A +.001 –.005 PT 6 .469 .641 .688 .953 .348 .493 S M +.010 –.000 SP L Max. PT .524 .825 .431 Z Max. SP N Dia. Max. PT SP .462 .323 .465 .438 8 .594 .734 .812 1.047 .473 .493 .524 .825 .431 .462 .449 .465 .438 10 .719 .812 .938 1.125 .590 .493 .524 .825 .431 .462 .573 .465 .438 12 .812 .938 1.031 1.250 .750 .493 .524 .825 .431 .462 .699 .465 .438 14 .906 1.031 1.125 1.344 .875 .493 .524 .825 .431 .462 .823 .465 .438 16 .969 1.125 1.219 1.438 1.000 .493 .524 .825 .431 .462 .949 .465 .438 18 1.062 1.203 1.312 1.516 1.125 .493 .524 .825 .431 .462 1.073 .465 .438 20 1.156 1.297 1.438 1.672 1.250 .650 .650 1.076 .556 .556 1.199 .526 .531 22 1.250 1.375 1.562 1.750 1.375 .650 .650 1.076 .556 .556 1.323 .526 .531 24 1.375 1.500 1.688 1.875 1.500 .683 .683 1.109 .589 .589 1.449 .493 .497 All dimensions for reference only. 15 PT06 (MS3116) SP06 straight plug S L J Z Q “PG” Cable Gland Seal “A” General Duty L “A” (SR), “E” (SR), “P” (SR), MS / “F” Strain Relief “E” Open Wire Seal L V N L TERMINATION ASSEMBLIES D “P” Potting Boot L L GDH N N N N D D PT06PG-XX-XXX SP06PG-XX-XXX PTG06PG-XX-XXX C .375 MIN “J” Cable Seal PT06A-XX-XXX (SR) SP06A-XX-XXX (SR) PTG06A-XX-XXX (SR) PT06E-XX-XXX (SR) SP06E-XX-XXX (SR) PTG06E-XX-XXX (SR) PT06P-XX-XXX (SR) SP06P-XX-XXX (SR) PTG06P-XX-XXX (SR) MS3116F-XX-XXX PT06A-XX-XXX SP06A-XX-XXX PTG06A-XX-XXX PT06E-XX-XXX SP06E-XX-XXX PTG06E-XX-XXX MS3116E-XX-XXX XL PT06P-XX-XXX SP06P-XX-XXX PTG06P-XX-XXX MS3116P-XX-XXX PURCHA N D RELEASED / Dec . 21 2015, 2:09:12 PM MS3116J-XX-XXX To complete part number see how to order on page 25. Shell Size  6  8 10 12 14 16 18 20 22 24* Plug Front View S Max. .625 .750 .859 1.013 1.156 1.281 1.319 1.531 1.656 1.776 J .353 .353 .353 .353 .353 .353 .353 .415 .415 .415 L Max. .906 .906 .906 .906 .906 .906 .906 1.062 1.062 1.125 Plug Side View Q Thread Class 2A Class “A” (SR), “E” (SR), “P” (SR), MS / “F” Shell C Size Thread 6 8 10 12 14 16 18 20 22 24 – 6-32 6-32 6-32 6-32 6-32 8-32 8-32 8-32 8-32 D Min. – .240 .302 .428 .552 .615 .740 .740 .928 .990 G Max. – .125 .188 .312 .375 .500 .625 .625 .750 .800 H Max. – .812 .875 1.000 1.125 1.188 1.438 1.438 1.625 1.719 L Max. – 1.922 1.922 1.922 1.922 2.047 2.078 2.344 2.344 2.406 N Max. – .550 .675 .803 .920 1.047 1.165 1.290 1.418 1.543 Z Max.   .3125-32 NEF   .4375-28 UNEF   .5625-24 NEF   .6875-24 NEF   .8125-20 UNEF   .9375-20 UNEF 1.0625-18 NEF 1.1875-18 NEF 1.3125-18 NEF 1.4375-18 NEF Class “E”, MS / “E” L Max. 1.266 1.266 1.266 1.266 1.266 1.266 1.266 1.516 1.516 1.578 N Max. .440 .560 .685 .813 .930 1.057 1.175 1.301 1.430 1.555 .594 .594 .594 .594 .594 .594 .594 .672 .672 .672 D Min. .175 .297 .421 .546 .663 .787 .879 1.014 1.135 1.259 Class “P”, MS / “P” D Min. .192 .317 .434 .548 .673 .798 .899 1.024 1.149 1.274 All dimensions for reference only. 16 L Max. 1.438 1.438 1.438 1.438 1.438 1.438 1.438 1.656 1.656 1.717 L Max. N Max. .484 .608 .734 .858 .984 1.110 1.234 1.360 1.484 1.610 1.609 1.609 1.609 1.609 1.609 1.609 1.609 1.656 1.656 1.750 Class “A” N Max. .462 .590 .717 .834 .970 1.088 1.216 1.332 1.460 1.587 Class “J” D N Closed Free Max. – .168 .205 .338 .416 .550 .600 .635 .670 .740 – .230 .312 .442 .539 .616 .672 .747 .846 .894 – .547 .675 .812 .940 1.067 1.194 1.322 1.449 1.576 XL Max. – 2.271 2.271 2.411 2.599 2.943 3.172 3.610 3.766 3.985 V Thread Class A   .3750-32 NEF   .5000-28 UNEF   .6250-24 NEF   .7500-20 UNEF   .8750-20 UNEF 1.0000-20 UNEF 1.1875-18 NEF 1.1875-18 NEF 1.4375-18 NEF 1.4375-18 NEF Class “PG” B Thread – M12x1.5-6H M16x1.5-6H M16x1.5-6H M18x1.5-6H M22x1.5-6H M25x1.5-6H M25x1.5-6H M32x1.5-6H M32x1.5-6H L Max. – .936 .936 .936 .936 .936 .936 1.180 1.180 1.180 PT07 (MS3114) SP07 jam nut receptacle S H M S “A” General Duty/ “C” Pressurized Receptacle PT07A-XX-XXX PT07C-XX-XXX J A R M Z N P Shell Size 6 8 10 12 14 16 18 20 22 24 H ±.016 .625 .750 .875 1.062 1.188 1.312 1.438 1.562 1.688 1.816 Shell C Size Thread  6  8 10 12 14 16 18 20 22 24* – 6-32 6-32 6-32 6-32 6-32 8-32 8-32 8-32 8-32 S .812 .938 1.062 1.250 1.375 1.500 1.625 1.812 1.938 2.062 .348 .473 .590 .750 .875 1.000 1.125 1.250 1.375 1.500 J Flat +.000 –.010 .405 .530 .655 .818 .942 1.066 1.191 1.316 1.441 1.566 Class “A” (SR), “P” (SR), MS / “F” D Max. G H L – .250 .312 .438 .562 .625 .750 .750 .938 1.000 – .125 .188 .312 .375 .500 .625 .625 .750 .800 – .781 .844 .969 1.094 1.156 1.406 1.406 1.594 1.594 – 1.062 1.062 1.062 1.062 1.188 1.188 1.250 1.250 1.250 .125 .125 .125 .125 .125 .125 .125 .156 .156 .156 M – .696 .696 .696 .696 .696 .696 .884 .884 .917 Receptacle Side View P Panel Thickness M .696 .696 .696 .696 .696 .696 .696 .884 .884 .917 C Thread – 6-32 6-32 6-32 6-32 6-32 8-32 8-32 8-32 8-32 Min. Max. .062 .062 .062 .062 .062 .062 .062 .062 .062 .062 .125 .125 .125 .125 .125 .125 .125 .250 .250 .250 D Max. – .250 .312 .438 .562 .625 .750 .750 .938 1.000 * Size 24 strain relief available in PT only.          All dimensions for reference only. 17 D N R PT07A-XX-XXX (SR) SP07A-XX-XXX (SR) PT07E-XX-XXX (SR) MS3114F-XX-XXX K +.011 –.010 – .125 .188 .312 .375 .500 .625 .625 .750 .800 P L PT07P-XX-XXX MS3114P-XX-XXX Class “E”, MS / “E” R Thread Class 2A UNEF Z   .4375-28   .5625-24   .6875-24   .8750-20 1.0000-20 1.1250-18 1.2500-18 1.3750-18 1.5000-18 1.6250-18 .231 .231 .231 .231 .231 .231 .231 .261 .261 .228 Class “E” (SR) G Z J A C L P To complete part number see how to order on page 25. A Dia. +.001 –.005 M GD H R L “P” Potting Boot Z J A PT07E-XX-XXX SP07E-XX-XXX MS3114E-XX-XXX Recept. Front View K “A” (SR), “E” (SR), “P” (SR), MS / “F” Strain Relief J A R P TERMINATION ASSEMBLIES “E” Open Wire Seal M Z H – .775 .837 .963 1.087 1.150 1.400 1.400 1.587 1.681 L – 1.029 1.029 1.029 1.029 1.161 1.161 1.224 1.224 1.320 M – .696 .696 .696 .696 .696 .696 .884 .884 .917 L Max. M .568 .568 .568 .568 .568 .568 .568 .630 .630 .660 D Max. .202 .327 .444 .558 .683 .808 .909 1.034 1.159 1.284 .696 .696 .696 .696 .696 .696 .696 .884 .884 .917 N Max. .604 .729 .854 .979 1.104 1.229 1.354 1.510 1.635 1.760 Class “P”, MS / “P” L +.010 –.026 M N .593 .593 .593 .593 .593 .593 .593 .718 .718 .718 .696 .696 .696 .696 .696 .696 .696 .884 .884 .917 .484 .608 .734 .858 .984 1.110 1.234 1.360 1.484 1.610 Z ±.040 .191 .191 .191 .191 .191 .191 .191 .221 .221 .188 Z .191 .191 .191 .191 .191 .191 .191 .221 .221 .188 PT08 E SP08 E 90 degree plug G “E” Open Wire Seal, “E” (SR) Strain Relief TERMINATION ASSEMBLIES “P” Potting Boot 75 degrees L L E A B PT08E-XX-XXX SP08E-XX-XXX PT08E-XX-XXX (SR) SP08E-XX-XXX (SR) H PT08P-XX-XXX SP08P-XX-XXX D K C To complete part number see how to order on page 25. All lockwire holes are  .044 Dia. Min. Plug Front View Plug Side View Class “E”, “E” (SR) B ±.031 C +.010 –.025 .796 .655 10 .921 12 1.046 14 Class “P” D ±.062 E +.047 –.025 L ±.057 A ±.025 H ±.015 K ±.015 L Max. .169 .941 .339 1.786 .469 .312 .438 1.656 .749 .170 1.191 .393 1.880 .547 .438 .562 1.781 .812 .264 1.191 .450 1.965 .625 .516 .688 1.843 1.171 .905 .310 1.254 .519 2.113 .734 .625 .781 1.953 16 1.297 1.030 .330 1.316 .583 2.315 .750 .656 .890 2.000 18 1.422 1.015 .444 1.562 .621 2.423 .781 .703 1.000 2.046 20 1.562 1.077 .510 1.625 .683 2.695 .859 .766 1.125 2.218 22 1.672 1.139 .515 1.719 .739 2.742 .906 .812 1.234 2.265 24 1.797 1.265 .656 1.751 .797 2.980 1.169 .918 1.374 2.624 Shell Size 8 G Dia. Max. All dimensions for reference only. 18 PT Connectors with Printed Circuit Board Contacts S R 4 HOLES .120 ± .005 Dia. (.147 ± .005 Dia., size 24) (TP) Box Mounting Receptacle (PT02) with PCB Contacts R S Shell Size 71-570121-XXX 6 71-570120-XXX 10 71-570122-XXX 8 12 14 16 18 20 22 24 R (TP) K +.021 –.010 L Max. M +.010 –.000 N Dia. Max. Z +.040 –.050 .594 .812 .473 .493 .825 .431 .449 .380 .688 .938 .969 1.219 1.000 1.438 1.250 1.062 71-570128-XXX 1.250 1.125 1.312 1.156 71-570129-XXX .590 1.031 71-570126-XXX 71-570127-XXX .348 .812 .906 71-570125-XXX Receptacle Side View A +.001 –.005 .719 71-570124-XXX 1.562 1.375 1.688 All dimensions for reference only. .750 .875 1.125 1.375 1.500 .493 .825 .493 .825 .493 .650 1.076 .683 1.109 .650 Jam Nut Receptacle (PT07) with PCB Contacts .431 1.073 .556 1.323 71-533721-XXX .750 6 71-533720-XXX 10 71-533722-XXX 8 12 14 16 18 20 22 24 .625 R 71-533725-XXX 1.312 71-533726-XXX 71-533727-XXX 71-533728-XXX 71-533729-XXX All dimensions for reference only. M ±.010 .938 .473 .530 .125 .696 1.375 1.062 71-533724-XXX S ±.010 K +.011 –.010 1.188 71-533723-XXX 1.438 1.562 1.688 1.816 1.250 .348 .590 .750 .875 .405 .655 .818 .942 1.500 1.000 1.066 1.812 1.250 1.316 1.625 1.938 2.062 .253 Z P K Receptacle Side View J Flat +.000 –.010 1.062 .286 .030 ± .001 A Dia. +.001 –.005 .875 .286 J A S .812 .380 1.449 M Receptacle Front View Shell Size .380 1.199 .589 All lockwire holes are  .044 Dia. Min. Order by applicable part number in chart below; add insert arrangement number. Refer to insert availability on pages 4-10. H +.017 –.016 .380 .949 .556 1.076 .380 .823 .431 .825 .380 .699 .431 .825 .380 .573 .431 .825 .493 .323 .431 .825 .493 .493 .431 S H Part Number* PT07 with PCB Contacts Z S +.011 –.010 .469 71-570123-XXX N K Receptacle Front View Part Number* PT02 with PCB Contacts .030 ± .001 A (TP) Order by applicable part number in chart below; add insert arrangement number. Refer to insert availability on pages 4-10. n (MMC) located within  .0025 of (TP) L M 1.125 1.375 1.500 1.191 1.441 1.566 .125 .125 .125 .125 .125 .125 .156 .156 .156 P Panel Thickness Min. Max. .062 .125 .696 .062 .696 .062 .696 .696 .696 .696 .884 .884 .917 .062 .062 .062 .062 .062 .062 .062 R Thread Class 2A Z +.025 –.035   .5625-24 UNEF .376 .125   .4375-28 UNEF .125   .6875-24 UNEF .125 .125 .125 .125 .250 .250 .250   .8750-20 UNEF 1.0000-20 UNEF 1.1250-18 UNEF 1.2500-18 UNEF 1.3750-18 UNEF 1.5000-18 UNEF 1.6250-18 UNEF .376 .376 .376 .376 .376 .376 .367 .367 .334 * For RoHS compliance connectors with PCB contacts change “71”- to:   “FL” designates conductive gray zinc nickel plating   “93” designates black zinc cobalt plating 19 PTB SPB thru bulkhead receptacle S R PTB .120 ± .005 Dia. (.147 ± .005 Dia., size 24) SPB .150 ± .005 Dia. (TP) R S 4 Holes P M L A A (TP) K * PTB-XX-XXX * SPB-XX-XXX   * To complete part number add desired arrangement number (refer to pages 4 and 5 for insert availability) and add “PS”; Example:  PTB-18-32PS. If a rotation is required, use PTB-18-32PS and add W, X, Y or Z. Example: PTB-18-32 PSW. The socket end of the insert always appears at the “P” dimension end of shell. n (MMC) located within  .0025 of (TP) Receptacle Front View R (TP) Receptacle Side View P Max. SPB A +.001 –.005 K +.016 –.000 L ±.005 M +.010 –.000 PTB SPB .953 .348 .625 1.050 .562 .125 .188 .812 1.047 .473 .625 1.050 .562 .125 .188 .812 .938 1.125 .590 .625 1.050 .562 .125 .188 .812 .938 1.031 1.250 .750 .625 1.050 .562 .125 .188 .906 1.031 1.125 1.344 .875 .625 1.050 .562 .125 .188 16 .969 1.125 1.219 1.438 1.000 .625 1.050 .562 .125 .188 18 1.062 1.203 1.312 1.516 1.125 .625 1.050 .562 .125 .188 20 1.156 1.297 1.438 1.672 1.250 .781 1.330 .688 .125 .312 22 1.250 1.375 1.562 1.750 1.375 .781 1.330 .688 .125 .312 24 1.375 1.500 1.688 1.875 1.500 .781 1.330 .688 .125 .312 S Shell Size PTB SPB PTB 6 .469 .641 .688 8 .594 .734 10 .719 12 14 All dimensions for reference only. 20 PT hermetic Three shell styles are available in the hermetic PT bayonet series: • PTIH (MS3113H) • PT02H • PT07H (MS3114H) These hermetic connectors are only available with solder cup or flat eyelet pin contacts in the MS/PT version. Socket contacts are available in some proprietary PT versions. Other design characteristics of the PT hermetic connector series are as fol­lows: Shell sizes: 8 through 24 (tin plated) solder mounting receptacle Contact count: 2 through 61. Refer to pages 4 and 5 for insert availability for hermetics. Current: 5.0 amp each #20 contact 10 amp each #16 contact 17 amp each #12 contact Contacts are tin plated for PT; gold is optional Dielectric Withstanding Voltage (sea level): 1500 volts (RMS) 60 cps, Service Rating I 2300 volts (RMS) 60 cps, Service Rating II Compression glass inserts, permanently lettered Helium Leakage: Less than 1.0 X 10-6 cc/sec. at 15 psi differential box mounting receptacle Physical Shock: 100 G’s Vibration: Exceeds MIL-E-5272 Procedure II Thermal Shock: No deterioration or failure after 5 cycles at –55°F to +257°F Intermateability: Mates with MS3116 and PT06 Refer to pages 4-10 for insert arrangement availability. jam nut receptacle 21 PTIH (MS3113H) hermetic solder mounting receptacle L G W A N .031 +.006 –.005 Z * PTIH-XX-XXX ** PTIY-XX-XXX ** MS3113H-XXCXXX † PTIH-XX-XXX (100) †† PTIY-XX-XXX (100) †† MS3113H-XXYXXX To complete part number see how to order on page 25. * Solder cup pin contacts without interfacial seal ** Solder cup pin contacts with interfacial seal † Flat eyelet pin contacts without interfacial seal †† Flat eyelet pin contacts with interfacial seal Recept. Front View G Dia. Max. A Dia. +.001 –.005 L +.025 –.016 N Dia. +.001 –.005 W +.011 –.010 Z Max. 6 .511 .348 .447 .438 .094 .386 8 .636 .473 .447 .562 .094 .386 10 .761 .590 .447 .672 .094 .386 12 .855 .750 .447 .781 .094 .386 14 .980 .875 .447 .906 .094 .386 16 1.105 1.000 .447 1.031 .094 .386 18 1.229 1.125 .447 1.156 .094 .386 20 1.323 1.250 .509 1.250 .094 .386 22 1.449 1.375 .509 1.375 .125 .418 24 1.574 1.500 .542 1.500 .125 .418 Shell Size Receptacle Side View All dimensions for reference only. 22 PT02H hermetic box mounting receptacle PT .120 ± .005 Dia. (.147 ± .005 Dia., size 24) S R (TP) L R S 4 Holes A (TP) N U W SP .150 ± .005 Dia. Z * PT02H-XX-XXX ** PT02Y-XX-XXX † PT02H-XX-XXX (100) †† PT02Y-XX-XXX (100) To complete part number see how to order on page 25. * Solder cup pin contacts without interfacial seal ** Solder cup pin contacts with interfacial seal † Flat eyelet pin contacts without interfacial seal †† Flat eyelet pin contacts with interfacial seal n (MMC) located within  .0025 of (TP) Receptacle Front View Receptacle Side View Shell Size R (TP) S ±.016 A Dia. +.001 –.005 K ±.015 L +.025 –.015 N Dia. +.001 –.005 U +.011 –.010 Z Max. 6 .469 .688 .348 .047 .494 .438 .062 .344 8 .594 .812 .473 .047 .494 .562 .062 .344 10 .719 .938 .590 .047 .494 .672 .062 .344 12 .812 1.031 .750 .047 .494 .781 .062 .344 14 .906 1.125 .875 .047 .494 .906 .062 .344 16 .969 1.219 1.000 .047 .494 1.031 .062 .344 18 1.062 1.312 1.125 .047 .494 1.156 .062 .344 20 1.156 1.438 1.250 .047 .556 1.250 .062 .344 22 1.250 1.562 1.375 .079 .556 1.375 .062 .377 24 1.375 1.688 1.500 .079 .588 1.500 .062 .377 All dimensions for reference only. 23 PT07H (MS3114H) hermetic jam nut receptacle S H M S A R Z P K * PT07H-XX-XXX ** PT07Y-XX-XXX ** MS3114H-XXCXXX † PT07H-XX-XXX (100) †† PT07Y-XX-XXX (100) †† MS3114H-XXYXXX To complete part number see how to order on page 25. * Solder cup pin contacts without interfacial seal ** Solder cup pin contacts with interfacial seal † Flat eyelet pin contacts without interfacial seal †† Flat eyelet pin contacts with interfacial seal Receptacle Front View Receptacle Side View Shell Size S +.016 H Hex +.017 –.016 A +.001 –.005 K +.043 –.016 M +.031 –.000 Max. Min. R Thread Class 2A 6 .812 .625 .348 .094 8 .938 .750 .473 .094 .696 .125 .062   .4375-28 UNEF .206 .696 .125 .062   .5625-24 NEF 10 1.062 .875 .590 .206 .094 .696 .125 .062   .6875-24 NEF 12 1.250 1.062 .206 .750 .094 .696 .125 .062   .8750-20 UNEF 14 1.375 .206 1.188 .875 .094 .696 .125 .062 1.0000-20 UNEF .206 16 18 1.500 1.312 1.000 .094 .696 .125 .062 1.1250-18 NEF .206 1.625 1.438 1.125 .094 .696 .125 .062 1.2500-18 NEF .206 20 1.812 1.562 1.250 .125 .884 .250 .062 1.3750-18 NEF .081 22 1.938 1.688 1.375 .125 .884 .250 .062 1.5000-18 NEF .081 24 2.062 1.812 1.500 .125 .917 .250 .062 1.6250-18 NEF .048 All dimensions for reference only. 24 P Panel Thickness Z Max. PT, SP, MS/PT how to order PT, SP To more easily illustrate ordering procedure, part number PT00A-20-41PW(SR) is shown as follows: PT 00 A - 20 - 41 P W (SR) 1 2 3 4 5 6 7 8 See code below: 1. Connector Type “PT” designates standard olive drab, electrically conductive cadmium plate bayonet lock connector with solder contacts “SP” designates electrically non-conductive, hard anodic coated bayonet lock connector with solder contacts and larger flange and mounting holes for back panel mounting “PTG” designates plug with grounding fingers 2. Shell Style “00” designates wall mounting receptacle “01” designates cable connecting receptacle** “02” designates box mounting receptacle “06” designates straight plug “07” designates jam nut receptacle “08” designates 90 degree plug cable support “B” designates thru bulkhead receptacle (pressurized) “I” designates solder mount receptacle (Hermetic only) 3. Service Classes “A” designates general duty back shell “C” designates pressurized receptacle “E” designates environmental resisting open wire seal with grommet and nut “P” designates assembly with potting boot “PG” designates adapter for cable gland for moisture proofing jacketed cables “H” designates hermetic* without interfacial seal “Y” designates hermetic* with interfacial seal 4. Shell Size “20” designates shell size. Shell sizes 6 through 24 available. 5. Insert Arrangement - Refer to pages 4-10 for insert availability. “20 - 41” designates insert arrangement. (The number following the hyphen is the number only that is used in the part number). 6. Contacts “P” designates pin contacts “S” designates socket contacts For ordering connectors with printed circuit board contacts, see pg. 19. 7. Insert Rotation - Refer to page 6. “W”, “X”, “Y”, “Z” designate that insert is rotated in its shell from “normal position. No letter required for normal (no rotation) position. 8. “SR” designates a strain relief clamp. Indicate optional finishes as follows: (003) olive drab cadmium plate (standard on “PT”) (100) Suffix added for flat eyelet pin contacts in hermetic versions OR RoHS Compliant finish suffix as follow: (005) (023) (025) (072) (424) (470) anodic coating - Alumilite® (standard on “SP”) electroless nickel black zinc cobalt plating conductive gray zinc nickel plating electroless nickel finish with strain relief black zinc cobalt plating with strain relief MS/PT MIL-DTL-26482, Series 1 Part number MS3110E20-41PW is shown as follows: MS 311 0 E 20 - 41 P W 1 2 3 4 5 6 7 8 For Hermetic connectors part number MS3113H20Y41PW is shown as follows: MS 311 3 H 20 Y 41 P W 1 2 3 4 5, 6 7 8 See code below: 1. “MS” designates Military Standard 2. Specification Number “311” designates basic family number for MIL-DTL-26482, Series 1 solder type 3. Shell Style “0” designates wall mounting receptacle “1” designates cable connecting receptacle** “2” designates box mounting receptacle “3” designates solder mount receptacle (hermetic only) “4” designates jam nut receptacle “6” designates straight plug 4. Service Class “E” designates environmental resisting connector “F” designates environmental resisting connectors with strain relief “J” designates clamp assembly for moisture proofing multi-jacketed cables, with strain relief “P” designates potted type with potting boot “H” designates hermetic 5. Shell Size “20” designates shell size. Shell sizes 8 through 24 available. 6. Insert Arrangement - Refer to pages 4-10 for insert availability. “20 - 41” designates arrangement. (The number fol­lowing the hyphen is the number only that is used in the part number). Hermetic version “20Y41” designates insert arrangement; specify “Y” for flat eyelet pin contacts, or “C” for solder cup pin contacts 7. Contact Configuration “P” designates pin contacts “S” designates socket contacts 8. Insert Rotation- Refer to page 6. “W”, “X”, “Y”, “Z” designate that insert is rotated in it shell from “normal” position. No letter require fo nor­mal (no rotation) position. * Hermetic connectors are supplied with tin plated shells. ** This connector style is sometimes referred to as a cable connect­ing “plug”. It does, however, mate with either a straight or 90 degree plug. 25 Amphenol   PT-SE, SP-SE, MS/PT-SE Proprietary/MIL-DTL-26482, Series 1 bayonet coupling and crimp termination Amphenol® SE crimp type miniature connectors provide performance and versatility needed for applications demanding high reliability and crimp removable contacts. These crimp contacts are rear insertable/front release and are held in position by an MS approved spring tower reten­tion system. The MS/PT-SE Series is qualified to MIL-DTL-26482, Series 1 and has all the outstanding design characteristics and quality of the PT Series. wall mounting receptacle The SP-SE Series is a modification of the PT-SE, providing special shells with a wide mounting flange for back panel mounting. A corrosion resistant electrically conductive finish of cadmium plate with an olive drab chromate after-treatment is used on the PT-SE and MS/PT-SE. The SP-SE is given a durable non-con­ ductive hard anodic “Alumilite”® coating which provides abra­sion protection and resistance to corrosion. cable connecting receptacle* **NEW** 500 hour corrosion resistance, RoHS compliant harsh environment conductive plating. Gray Zinc over an Electroless Nickel (Gray ZnNi) base, with a Light Gun Metal Gray appearance. Shell components for these series are aluminum. The depend­ able 5 key/keyway polarization with bayonet lock coupling assures positive mating with no chance of cross plugging. Spring tension provided by a wave washer in the coupling nut ensures maintenance of interfacial seal between mating halves. box mounting receptacle Both the insert and main joint gasket are molded from resilient neoprene. This provides excellent moisture sealing at the gas­ket and superior electrical isolation of the contact in the insert. Both pins and sockets are machined from a copper alloy and are gold plated. This gold plating eliminates contact corrosion and offers an indefinite shelf life. Socket contacts for these series are a closed entry design. straight plug Breakaway style plug is available in PT-SE crimp. The PT-SE, SP-SE and MS/PT-SE Series are intermateable and intermountable with all existing Miniature Cylindrical Series connectors. jam nut receptacle Refer to pages 4-10 for insert arrangement availability. * This connector style is sometimes referred to as a cable connecting “plug”. It does, however, mate with either a straight or 90 degree plug. 26 PT-SE. SP-SE, MS/PT-SE Contact Specifications Test Current Maximum Millivolt Drop† Crimp Well Diameter Minimum Well Depth 20 7.5 55 .049 ±.001 .267 16 13.0 49 .067 ±.001 .236 12 23.0 42 .100 ±.002 .236 Contact Size “SE”, MS / “E” open wire seal Service Rating Recommended Operating AC Voltage at Sea Level Sea Level 50,000 ft. I 600 1,500 500 375 200 II 1,000 2,300 750 500 200 Service Rating Test Voltage AC (RMS), 60 cps 70,000 110,000 ft. ft. † Silver plated wire per MIL-DTL-26482 PT-SE and SP-SE Service Classes PT-SE and SP-SE connectors are available in the three service classes listed below. “SE” “SE” (SR), MS / “F” strain relief clamp Open wire sealing - environmental resistant, with a nut and grommet for moisture proof­ing individual wires “SE” (SR) Strain relief clamp - environmental resistant strain relief clamp and grommet for moisture proofing individual wires; provides added wire bundle support “SP” Translucent nylon boot for retaining cus­tomer applied potting compounds; held in place by a threaded ring MS/PT-SE Service Classes MS-SE series connectors are available in the following certified service classes: “E” “F” “P” “SP”, MS / “P” potting boot Open wire sealing - environmental resisting connectors are supplied with a multi-hole grommet and clamping nut for moisture proofing individual open wires Environmental resistant strain relief clamp and grommet for moisture proofing individual wires; provides added wire bundle support Potting applications - these connectors are supplied with a translucent nylon boot for retention of customer applied potting com­ pound 27 PT00 SE (MS3120) SP00 SE wall mounting receptacle S R T Dia. 4 Holes (TP) R S (TP) TERMINATION ASSEMBLIES “SE” Open Wire Seal “SE” (SR), MS / “F” Strain Relief L L M A L K A N M “SP” Potting Boot G A N K D N M PT00SE-XX-XXX SP00SE-XX-XXX MS3120E-XX-XXX PT00SE-XX-XXX (SR) SP00SE-XX-XXX (SR) MS3120F-XX-XXX K PT00SP-XX-XXX SP00SP-XX-XXX To complete part number see how to order on page 36. n (MMC) located within  .005 of (TP) Receptacle Front View Shell Size 8 10 12 14 16 18 20 22 24 Shell Size 8 10 12 14 16 18 20 22 24 PT R (TP) .594 .719 .812 .906 .969 1.062 1.156 1.250 1.375 SP – .812 .938 1.031 1.125 1.203 1.297 1.375 1.500 PT .828 .954 1.047 1.141 1.234 1.328 1.453 1.578 1.703 Class “SE”, MS / “E” L N Dia. Max. Max 1.328 1.328 1.328 1.328 1.328 1.328 1.359 1.359 1.422 .560 .704 .825 .954 1.080 1.204 1.330 1.454 1.580 S Max. SP – 1.141 1.266 1.360 1.453 1.532 1.688 1.766 1.891 G Dia. .125 .188 .312 .375 .500 .625 .625 .750 .800 PT .120 .120 .120 .120 .120 .120 .120 .120 .147 T Dia. ± .005 SP – .150 .150 .150 .150 .150 .150 .150 .150 A Dia. +.001 –.005 .473 .590 .750 .875 1.000 1.125 1.250 1.375 1.500 Class “SE” (SR), MS / “F” L Max. 2.422 2.422 2.422 2.422 2.537 2.537 2.824 2.824 2.900 * Back panel mounting All dimensions for reference only. 28 N Max. .781 .844 .969 1.094 1.156 1.406 1.406 1.594 1.688 K ±.016 .062 .062 .062 .062 .062 .062 .094 .094 .094 Receptacle Side View M +.010 P* –.000 Max. Panel Thickness PT SP PT SP .431 .431 .431 .431 .431 .431 .556 .556 .589 D Dia. Max. – .444 .558 .683 .808 .909 1.034 1.159 1.284 – .462 .462 .462 .462 .462 .556 .556 .589 .094 .094 .094 .094 .094 .094 .219 .219 .219 Class “SP”, MS / “P” L Max. – 1.656 1.656 1.656 1.656 1.656 1.750 1.750 1.782 – .125 .125 .125 .125 .125 .219 .219 .219 N Dia. Max. – .734 .858 .984 1.110 1.234 1.360 1.484 1.610 MF00 SE (MS3128) wall mounting receptacle T¹ Dia. 4 Holes S R¹ (TP) R (TP) R R¹ (TP) (TP) S T Dia. 4 Holes TERMINATION ASSEMBLIES MS / “E” Open Wire Seal L L K M N A M MS / “F” Strain Relief A K MF00SE-XX-XXX MS3128E-XX-XXX GF N MF00SE-XX-XXX (SR) MS3128F-XX-XXX To complete part number see how to order on page 36. n (MMC) located within  .0025 of (TP) Receptacle Front View Shell Size Receptacle Side View Class MS / “E” Class MS / “F” T Dia. ±.005 T1 Dia. ±.005 A Dia. +.001 –.005 K ±.016 M +.010 –.000 L Max. N Max. F Min. G Dia. L Max. N Max. R R1 S Max. 10 .719 .812 1.141 .120 .150 .590 .062 .462 1.328 .685 .297 .188 1.906 .891 12 .812 .938 1.266 .120 .150 .750 .062 .462 1.328 .813 .422 .312 1.906 1.016 14 .906 1.031 1.360 .120 .150 .875 .062 .462 1.328 .930 .547 .375 1.906 1.141 16 .969 1.125 1.453 .120 .150 1.000 .062 .462 1.328 1.057 .609 .500 2.000 1.203 18 1.062 1.203 1.532 .120 .150 1.125 .062 .462 1.328 1.175 .734 .625 2.000 1.469 20 1.156 1.297 1.688 .120 .150 1.250 .094 .556 1.359 1.301 .734 .625 2.172 1.469 22 1.250 1.375 1.766 .120 .150 1.375 .094 .556 1.359 1.428 .922 .750 2.172 1.656 24 1.375 1.500 1.891 .147 .150 1.500 .094 .589 1.422 1.533 .984 .800 2.234 1.750 All dimensions for reference only. 29 PT01 SE (MS3121) SP01 SE cable connecting receptacle S S TERMINATION ASSEMBLIES “SE”, MS / “E” Open Wire Seal “SE” (SR), MS / “F” Strain Relief “SP”, MS / “P” Potting Boot L L A N A L K G K PT01SE-XX-XXX SP01SE-XX-XXX MS3121E-XX-XXX D N A N K PT01SE-XX-XXX (SR) SP01SE-XX-XXX (SR) MS3121F-XX-XXX PT01SP-XX-XXX SP01SP-XX-XXX MS3121P-XX-XXX Note: This connector style is sometimes referred to as a cable connecting “plug”. It does, however, mate with either a straight or 90 degree plug. To complete part number see how to order on page 36. Receptacle Front View Receptacle Side View Class “SE”, MS / “E” Class “SE” (SR), MS / “F” Shell Size S Max. A Dia. +.001 –.005 L Max. G Dia. 8 .812 .473 .094 1.522 .560 .125 2.422 10 .955 .590 .094 1.522 .685 .188 12 1.048 .750 .094 1.522 .813 .312 14 1.142 .875 .094 1.522 .930 16 1.236 1.000 .094 1.522 18 1.329 1.125 .094 20 1.455 1.250 .115 22 1.579 1.375 24 1.709 1.500 Class “SP”, MS / “P” D Dia. L Max. N Dia. Max. .828 – – – 2.422 .891 .444 1.656 .734 2.422 1.016 .558 1.656 .858 .375 2.422 1.141 .683 1.656 .984 1.057 .500 2.537 1.203 .808 1.656 1.110 1.522 1.175 .625 2.537 1.469 .909 1.656 1.234 1.709 1.301 .625 2.824 1.469 1.034 1.750 1.360 .115 1.709 1.428 .750 2.824 1.656 1.159 1.750 1.484 .115 1.709 1.555 .800 2.900 1.750 1.284 1.782 1.610 K ±.018 N Dia. Max. All dimensions for reference only. 30 L Max. N Max. PT02 SE (MS3122) SP02 SE box mounting receptacle S L R M (TP) R S (TP) K A T Dia. 4 Holes N D PT02SE-XX-XXX SP02SE-XX-XXX MS3122E-XX-XXX To complete part number see how to order on page 36. n (MMC) located within  .0025 of (TP) Receptacle Front View Receptacle Side View T Dia. ±.005 PT SP K ±.016 L Max. PT SP .473 .312 – .062 1.296 .431 – .438 .150 .590 .312 .219 .062 1.296 .431 .462 .562 .150 .750 .312 .219 .062 1.296 .431 .462 .688 .120 .150 .875 .312 .219 .062 1.296 .431 .462 .812 1.453 .120 .150 1.000 .312 .219 .062 1.296 .431 .462 .938 1.328 1.532 .120 .150 1.125 .312 .219 .062 1.296 .431 .462 1.062 1.297 1.453 1.688 .120 .150 1.250 .406 .344 .094 1.358 .556 .556 1.188 1.375 1.578 1.766 .120 .150 1.375 .406 .344 .094 1.358 .556 .556 1.312 1.500 1.703 1.891 .147 .150 1.500 .406 .344 .094 1.358 .589 .589 1.438 R Shell Size PT SP 8 .594 – 10 .719 12 .812 14 PT SP PT SP .828 – .120 – .812 .954 1.141 .120 .938 1.047 1.266 .120 .906 1.031 1.141 1.360 16 .969 1.125 1.234 18 1.062 1.203 20 1.156 22 1.250 24 1.375 A Dia. +.001 –.005 M +.010 –.000 N Dia. +.011 –.000 S Max. All dimensions for reference only. 31 D Max. MF02 SE (MS3127) box mounting receptacle T¹ Dia. 4 Holes S R¹ L (TP) M R (TP) R R¹ (TP) (TP) S K A T Dia. 4 Holes N D MF02SE-XX-XXX MS3127E-XX-XXX To complete part number see how to order on page 36. n (MMC) located within  .0025 of (TP) Receptacle Front View Shell Size N Dia. +.011 –.000 Receptacle Side View S Max. T ±.005 T1 ±.005 A Dia. +.001 –.005 D Max. K ±.016 L Max. M +.010 –.000 R R 10 .562 .719 .812 1.141 .120 .150 .590 .219 .062 1.266 .462 12 .688 .812 .938 1.266 .120 .150 .750 .219 .062 1.266 .462 14 .812 .906 1.031 1.360 .120 .150 .875 .219 .062 1.266 .462 16 .938 .969 1.125 1.453 .120 .150 1.000 .219 .062 1.266 .462 18 1.062 1.062 1.203 1.532 .120 .150 1.125 .219 .062 1.266 .462 20 1.188 1.156 1.297 1.688 .120 .150 1.250 .344 .094 1.328 .556 22 1.312 1.250 1.375 1.766 .120 .150 1.375 .344 .094 1.328 .556 24 1.438 1.375 1.500 1.891 .147 .150 1.500 .344 .094 1.328 .589 1 All dimensions for reference only. 32 PT06 SE (MS3126) SP06 SE straight plug S TERMINATION ASSEMBLIES “SE”, MS / “E” Open Wire Seal “SE” (SR), MS / “F” Strain Relief L “SP”, MS / “P” Potting Boot L L N G N Z pin contacts Z¹ socket contacts D N Z pin contacts Z¹ socket contacts PT06SE-XX-XXX SP06SE-XX-XXX PTG06SE-XX-XXX MS3126E-XX-XXX Z pin contacts Z¹ socket contacts PT06SE-XX-XXX (SR) SP06SE-XX-XXX (SR) PTG06SE-XX-XXX (SR) MS3126F-XX-XXX PT06SP-XX-XXX SP06SP-XX-XXX PTG06SP-XX-XXX MS3126P-XX-XXX To complete part number see how to order on page 36. Plug Front View Plug Side View Class “SE”, MS / “E” Class “SE” (SR), MS / “F” Class “SP”, MS / “P” Shell Size S Dia. Max. Z ±.045 Z1 ±.045 L Max. N Max. G Dia. L Max. N Max. D Dia. L Max. N Dia. Max.  8* .734 .640 .579 1.328 .540 .125 2.413 .828 .327 1.750 .578 10 .859 .640 .579 1.328 .685 .188 2.413 .891 .444 1.750 .734 12 1.031 .640 .579 1.328 .813 .312 2.413 1.016 .558 1.750 .858 14 1.156 .640 .579 1.328 .930 .375 2.413 1.141 .683 1.750 .984 16 1.281 .640 .579 1.328 1.057 .500 2.528 1.203 .808 1.750 1.110 18 1.391 .640 .579 1.328 1.175 .625 2.528 1.469 .909 1.750 1.234 20 1.531 .640 .579 1.297 1.301 .625 2.753 1.469 1.034 1.750 1.360 22 1.656 .640 .579 1.297 1.428 .750 2.753 1.656 1.159 1.750 1.484 24 1.777 .640 .579 1.359 1.533 .800 2.830 1.750 1.284 1.766 1.610 *  PT-SE, MS-SE and MS-SP only. All dimensions for reference only. 33 PT07 SE (MS3124) SP07 SE jam nut receptacle S H S TERMINATION ASSEMBLIES “SE”, MS / “E” Open Wire Seal M “SE” (SR), MS / “F” Strain Relief L M K R “SP”, MS / “P” Potting Boot L M K K N J A F N J A PT07SE-XX-XXX SP07SE-XX-XXX MS3124E-XX-XXX G N J A R P P L R P PT07SE-XX-XXX (SR) SP07SE-XX-XXX (SR) MS3124F-XX-XXX PT07SP-XX-XXX SP07SP-XX-XXX MS3124P-XX-XXX To complete part number see how to order on page 36. All lockwire holes are  .044 Dia. Min. Receptacle Front View Shell Size H Hex Max. Shell Size Class “SE”, MS / “E” L N Max. Max. 8 10 12 14 16 18 20 22 24 8 10 12 14 16 18 20 22 24 .767 .892 1.079 1.205 1.329 1.455 1.579 1.705 1.829 1.438 1.438 1.438 1.438 1.438 1.438 1.625 1.625 1.688 S Max. .954 1.078 1.266 1.391 1.516 1.641 1.828 1.954 2.078 .749 .874 .999 1.124 1.249 1.374 1.530 1.655 1.780 A Dia. +.001 –.005 .473 .590 .750 .875 1.000 1.125 1.250 1.375 1.500 F Min. .234 .297 .422 .547 .609 .734 .734 .922 .984 J Flat +.000 –.010 .530 .655 .818 .942 1.066 1.191 1.316 1.441 1.566 K +.011 –.010 .125 .125 .125 .125 .125 .125 .156 .156 .156 Receptacle Side View P Panel Thickness M ±.005 Min. Max. .696 .696 .696 .696 .696 .696 .884 .884 .917 Class “SE” (SR), MS / “F” G Dia. L Free Max. .125 .188 .312 .375 .500 .625 .625 .750 .800 1.922 1.922 1.922 1.922 2.000 2.000 2.172 2.172 2.234 All dimensions for reference only. 34 .062 .062 .062 .062 .062 .062 .062 .062 .062 N Max. .828 .891 1.016 1.141 1.203 1.469 1.469 1.656 1.750 .125 .125 .125 .125 .125 .125 .250 .250 .250 G Dia. R Thread Class 2A   .5625-24 UNEF   .6875-24 NEF   .8750-20 UNEF 1.0000-20 UNEF 1.1250-18 NEF 1.2500-18 NEF 1.3750-18 NEF 1.5000-18 NEF 1.6250-18 NEF Class “SP”, MS /”P” L N Dia. Max. Max. – .444 .558 .683 .808 .909 1.034 1.159 1.284 – 1.656 1.656 1.656 1.656 1.656 1.922 1.922 1.951 – .734 .858 .984 1.110 1.234 1.360 1.484 1.610 PT08 SE SP08 SE 90 degree plug G TERMINATION ASSEMBLIES “SE” Open Wire Seal, “SE” (SR) Strain Relief “SP” Potting Boot 75 degrees L L E A B PT08SE-XX-XXX SP08SE-XX-XXX PT08SE-XX-XXX (SR) SP08SE-XX-XXX (SR) H D K PT08SP-XX-XXX SP08SP-XX-XXX C To complete part number see how to order on page 36. All lockwire holes are  .044 Dia. Min. Plug Front View Plug Side View Class “SE”, “SE” (SR) G Dia. Max. B ±.031 C +.010 –.025 10 12 .921 .749 1.046 .812 14 16 1.171 1.297 18 1.422 20 Class “SP” D ±.062 E +.047 –.025 L Max. A ±.025 H ±.015 K ±.015 L Max. .170 1.191 .393 2.137 .547 .438 .562 2.031 .264 1.191 .450 2.222 .625 .516 .688 2.093 .905 .310 1.254 .519 2.370 .734 .625 .781 2.203 1.030 .330 1.316 .583 2.572 .750 .656 .890 2.250 1.015 .444 1.562 .621 2.680 .781 .703 1.000 2.296 1.562 1.077 .510 1.625 .683 2.753 .859 .766 1.125 2.343 22 1.672 1.139 .515 1.719 .739 2.799 .906 .812 1.234 2.390 24 1.797 1.250 .656 1.750 .787 3.037 1.181 .918 1.374 2.624 Shell Size All dimensions for reference only. 35 PT-SE, SP-SE, MS/PT-SE how to order PT-SE, SP-SE To more easily illustrate ordering procedure, part number PT00SE-2041PW(SR) is shown as follows: PT 00 SE - 20 - 41 P W (SR) 1 2 3 4 5 6 7 8 See code below: 1. Connector Type “PT” designates standard olive drab, electrically conductive cadmium plated, bayonet lock connector with crimp contacts “MF” designates standard olive drab, electrically conductive cadmium plated, bayonet lock connector with dual mounting holes, and crimp contacts “SP” designates electrically non-conductive, hard anodic coated, bayonet lock connector with larger flange and mounting holes for back panel mounting, and crimp contacts “PTG” designates plug with grounding fingers 2. Shell Style “00” designates wall mounting receptacle “01” designates cable connecting receptacle* “02” designates box mounting receptacle “06” designates straight plug “07” designates jam nut receptacle “08” designates 90 degree plug 3. Service Classes “SE” designates environmental crimp “SP” designates potted type crimp Both of the above are Amphenol proprietary versions of the MILDTL-26482, Series 1 crimp contact connector and offer 15 lbs. contact reten­tion for size 20 contacts; 25 lbs. for size 16 contacts. “PG” designates adapter for cable gland for moisture proofing jacketed cables 4. Shell Size “20” designates shell size. Shell sizes 8 through 24 available. 5. Insert Arrangement Refer to pages 4-10 for insert availability. “20  -  41” designates insert arrangement. (The number following the hyphen is the number only that is used in the part number). 6. Contacts “P” designates pin contacts “S” designates socket contacts 7. Insert Rotation Refer to page 6. “W”, “X”, “Y”, “Z” designate that insert is rotated in its shell from “normal” position. No letter required for normal (no rotation) position. 8. “SR” designates a strain relief clamp. Indicate optional finishes as follows: (003) olive drab cadmium plate (standard on “PT”) OR RoHS Compliant finish suffix as follow: (005) anodic coating - Alumilite® (standard on “SP”) (023) electroless nickel (025) black zinc cobalt plating (072) conductive gray zinc nickel plating (424) electroless nickel finish with strain relief (470) black zinc cobalt plating with strain relief 36 MS/PT-SE MIL-DTL-26482, Series 1 To more easily illustrate ordering procedure, part number MS3120E20-41PW is shown as follows: MS 312 0 E 20 – 41 P W 1 2 3 4 5 6 7 8 See code below: 1. “MS” designates Military Standard 2. Specification Number “312” designates basic family for MIL-DTL-26482, Series 1 crimp type 3. Shell Style “0” designates wall mounting receptacle “1” designates cable connecting receptacle* “2” designates box mounting receptacle “4” designates jam nut receptacle “6” designates straight plug “7” designates box mounting receptacle with dual mounting holes “8” designates wall mounting receptacle with dual mounting holes 4. Service Class “E” designates environmental resisting connector “F” designates environmental resisting connector with strain relief “P” designates potted type with potting boot 5. Shell Size “20” designates shell size. Shell sizes 8 through 24 available 6. Insert Arrangement Refer to pages 4-10 for insert availability. “20 - 41” designates insert arrangement. (The number follow­ing the hyphen is the number only that is used in the part number). 7. Contacts “P” designates pin contacts “S” designates socket contacts 8. Insert Rotation Refer to page 6. “W”, “X”, “Y”, “Z” designate that insert is rotated in its shell from the “normal” position. No letter required for normal (no rotation) position. * This connector style is sometimes referred to as a cable connecting “plug”. It does, however, mate with either a straight or 90 degree plug. PT & SP accessories – sealing plugs, flange gaskets, potting boots SEALING PLUGS – FOR PT & SP C B DIA Contact Size .135 +.030 –.025 A DIA 12 16 20 Amphenol® Part Number A Dia. ±.010 MS Number 10-405996-12 MS27488-12 10-405996-16 MS27488-16 10-405996-20 MS27488-20 B Dia. ±.005 .121 .083 .060 .171 .133 .090 C ±.010 .564 .564 .564 Color Code Yellow Blue Red How to Order: Order by 10- (Proprietary) or MS part number as shown in chart above. SEALING PLUG MS27488-XX 10-405996-XX MOUNTING FLANGE GASKETS – FOR PT & SP S F PT 10-101949 Shell Size R S  6  8 10 12 14 16 18 20 22 24 T R MOUNTING FLANGE GASKET 10-101949-XX 10-150949-XX R ±.010 S ±.010   .469   .594   .719   .813   .906   .969 1.063 1.156 1.250 1.375   .688   .812   .938 1.031 1.125 1.219 1.312 1.438 1.563 1.688 PT & SP 10-101949 10-150949 SP 10-150949 R ±.010   .641   .734   .812   .938 1.031 1.125 1.203 1.297 1.375 1.500 S ±.010   .953 1.047 1.125 1.250 1.344 1.438 1.516 1.672 1.750 1.875 F +.016 –.000   .375   .500   .625   .750   .875 1.000 1.125 1.250 1.375 1.500 T ±.008 .024 .024 .024 .024 .024 .024 .024 .024 .024 .024 How to Order: For PT:  10-101949-XX (complete order number with desired shell size). For SP:  10-150949-XX (complete order number with desired shell size). 75° POTTING BOOTS – FOR PT & SP B E D L 75° POTTING BOOT 10-101988-XX Shell Size  8 10 12 14 16 18 20 22 24 B Max.   .433   .493   .552   .643   .658   .689   .750   .794 1.070 D ±.015 .312 .438 .516 .625 .656 .703 .766 .812 .918 E ±.015   .438   .562   .688   .781   .890 1.000 1.125 1.234 1.374 How to Order: 10-101988-XX (complete order number with desired shell size). All dimensions for reference only. 37 L Max.   .766   .830   .861   .916   .936   .959 1.052 1.073 1.310 PT & SP accessories – clamps CLASS “E” STRAIN RELIEF CLAMP – FOR PT & SP Shell Size L B  8 10 12 14 16 18 20 22 24 D G C CLASS “E” STRAIN RELIEF CLAMP 10-101971-XX B Max. C Thread Class 2B   .550   .675   .803   .920 1.047 1.165 1.291 1.418 1.533 6-32 NC 6-32 NC 6-32 NC 6-32 NC 6-32 NC 8-32 NC 8-32 NC 8-32 NC 8-32 NC D Min. .240 .302 .428 .552 .615 .740 .740 .928 .928 G Max.   .812   .875 1.000 1.125 1.188 1.438 1.438 1.719 1.719   .930   .930   .930   .930 1.062 1.062 1.093 1.093 1.093 How to Order: 10-101971-XX  X Add desired Add desired finish suffix† shell size “3” designates olive drab cadmium “5” designates Alumilite® Not for use with jam nut style connectors. CLASSES “A” & “P” STRAIN RELIEF CLAMP – FOR PT & SP L Shell Size B  8 10 12 14 16 18 20 22 24 D G C CLASSES “A” & “P” STRAIN RELIEF CLAMP 10-101980-XX C Thread Class 2B B Max.   .540   .665   .793   .910 1.037 1.155 1.281 1.408 1.533 6-32 NC 6-32 NC 6-32 NC 6-32 NC 6-32 NC 8-32 NC 8-32 NC 8-32 NC 8-32 NC D Min. .240 .302 .428 .552 .614 .740 .740 .928 .938 G Max.   .812   .875 1.000 1.125 1.188 1.438 1.438 1.719 1.719 How to Order: 10-101980-XX  X Add desired Add desired finish suffix† shell size “3” designates olive drab cadmium “5” designates Alumilite® Not for use with jam nut style connectors. CLASS “A” CABLE CLAMPS – FOR PT & SP Shell Size V Thread B 10 12 14 16 18/20 22/24 Amphenol® Part Number 97-3057-1004 97-3057-1007 97-3057-1008 97-3057-1010 97-3057-1012 97-3057-1016 A ±.031   .795   .850   .920   .920   .927 1.015 B Max.   .842   .995 1.120 1.216 1.403 1.683 C Dia. Min. .3125 .4375 .5625 .6250 .7500 .9375 V Thread   .6250-24   .7500-20   .8750-20 1.0000-20 1.1875-18 1.4375-18 How to Order: Order by 97-3057-XXXX number listed above. Standard finish is olive drab zinc alloy. Consult Amphenol, Sidney, NY for alternate finishes. C L Max. A CLASS “A” CABLE CLAMP 97-3057-XXXX † Standard accessory finishes are “3” olive drab cadmium for PT and MS/PT types, “5” Alumilite® for SP types. Electroless nickel plating is also available on some items; consult Amphenol, Sid­ney, NY All dimensions for reference only. 38 L +.010 –.020   .843   .843   .843   .843   .975   .975 1.007 1.007 1.007 PT, SP, MS/PT accessories – protection caps RECEPTACLE PROTECTION CAPS – FOR PT, SP, MS/PT C B Shell Size L 6 8 10 12 14 16 18 20 22 24 G X X X RECEPTACLE PROTECTION CAP FOR PT, SP, MS/PT CONNECTORS 10-101960-XXX 10-101961-XXX MS3181-XXX (Cable Connecting (Wall Receptacle)   Receptacle) B Dia. +.010 –.000 .328 .454 .578 .703 .844 .969 1.094 1.219 1.343 1.453 C Dia. +.010 –.000 .454 .578 .703 .891 1.016 1.141 1.266 1.391 1.516 1.614 G Dia. Max. .577 .706 .816 1.000 1.128 1.257 1.367 1.496 1.624 1.747 L +.020 –.000 X Std. & MS RA, CA, NA .563 .563 .563 .563 .563 .563 .563 .563 .563 .603 3.000 3.000 3.000 3.500 3.500 3.500 3.500 4.000 4.000 4.000 X MS only RAL/CAL/NAL 5.000 5.000 5.000 5.000 5.000 5.000 5.000 5.000 5.000 5.000 How to Order Proprietary Receptacle Caps: Wall Receptacle Caps: 10-101960-  XX  X Cable Connecting Receptacle Caps: 10-101961-  XX  X Jam Nut Receptacle Caps: 10-101964-  XX  X 10-101964-XXX MS3181-XXX (Jam Nut Receptacle) Add desired shell size Add desired finish suffix† “FL” designates gray zinc nickel “3” designates olive drab cadmium “5” designates Alumilite® Proprietary caps are supplied with standard bead chains only (as shown in draw­ing at left). For other chain options, an MS version cap should be ordered. How to Order MS Version Receptacle Caps: Wall Receptacle Caps: MS3181-  XX Jam Nut Recept. Caps: MS3181-  XX Shell size -CA for sash chain -CAL for long sash chain -RA for rope chain -RAL for long rope chain -NA for sash chain -NAL for long sash chain MS versions are supplied with standard anodize finish only. For other finish options a proprietary cap should be ordered. PLUG PROTECTION CAPS – FOR PT, SP, MS/PT L Shell Size  6  8 10 12 14 16 18 20 22 24 N X PLUG PROTECTION CAP FOR PT, SP, MS/PT CONNECTORS MS3180-XXX 10-101957-XXX N Dia. +.001 –.005   .348   .473   .590   .750   .875 1.000 1.125 1.250 1.375 1.500 L Dia. +.025 –.015 .532 .532 .532 .532 .532 .532 .532 .594 .594 .627 X Std. & MS CA, RA 3.000 3.000 3.000 3.500 3.500 3.500 3.500 4.000 4.000 4.000 X MS only CAL/RAL 5.000 5.000 5.000 5.000 5.000 5.000 5.000 5.000 5.000 5.000 How to Order Proprietary Plug Caps: 10-101957-XX  X Add desired shell size † Standard accessory finishes are “3” olive drab cadmium for PT and MS/PT types, “5” Alumilite® for SP types. Electroless nickel plating is also available on some items; consult Amphenol, Sidney, NY Add desired finish suffix† “FL” designates gray zinc nickel “3” designates olive drab cadmium “5” designates Alumilite® Proprietary caps are supplied with standard bead chains only (as shown in draw­ing at left). For other chain options an MS version cap should be ordered. How to Order MS Version Plug Caps: MS3180-  XX -CA for sash chain -CAL for long sash chain Shell size -RA for rope chain All dimensions for reference only. 39 -RAL for long rope chain PT & SP accessories – dummy receptacles, “O” rings, plastic dust caps DUMMY RECEPTACLES – FOR PT, SP, MS/PT S S¹ R R¹ M R S R¹ S¹ Shell Size K  8 10 12 14 16 18 20 22 24 N DUMMY RECEPTACLE FOR PT, SP, MS/PT CONNECTORS MS3115-XXX 10-150921-XXX K ±.010 .062 .062 .062 .062 .062 .062 .062 .062 .062 M +.030 –.000 .462 .462 .462 .462 .462 .462 .556 .556 .589 N +.001 –.005   .473   .590   .750   .875 1.000 1.125 1.250 1.375 1.500 Proprietary Version R S ±.005 ±.010   .734   .812   .938 1.031 1.125 1.203 1.297 1.375 1.500 How to Order Proprietary Dummy Receptacles: Add desired shell size Shell Size  6  8 10 12 14 16 18 20 22 24 Plug Plastic Dust Cap 10-70500-8 10-70506-12 10-70500-12 10-70506-16 10-70506-18 10-70506-20 10-70506-22 10-70506-24 10-70524-1 10-70506-28 Add desired shell size FOR PT, SP Receptacle Plastic Dust Cap 10-70506-8S 10-70506-10 10-70506-12 10-70506-14 10-70506-16 10-70506-18 10-70506-20 10-79506-22 10-70506-24 10-70524-1 10-150921-XX  X Add desired finish suffix† “FL” designates gray zinc nickel “3” designates olive drab cadmium “5” designates Alumilite® How to Order MS Version Dummy Receptacles: PLASTIC DUST CAPS 1.047 1.125 1.250 1.344 1.438 1.516 1.672 1.750 1.875 MS3115-XX  X Add desired finish suffix† -A designates Alumilite® -L designates electroless nickel -W designates olive drab cadmium How to Order Plastic Dust Caps: To the basic order number add the dust cap size to match connector plug or receptacle shell size, as shown in the tables above. Example: 10-70506-12 would be the correct order number for a plastic dust cap for a PT00 receptacle, shell size 10. All dimensions for reference only. 40 MS Version R1 S1 (TP) (TP)   .594   .719   .812   .906   .969 1.062 1.156 1.250 1.375   .828   .954 1.047 1.141 1.234 1.328 1.453 1.578 1.703 PT accessories glands Nylon Cable Glands Nylon Cable Glands Nylon Glands Material: Cable Nylon 66 (UL Approved 94V-2) Material: Seal Ring: Material: Seal Ring: Thread Type: Seal Ring: Thread Type: Temp Range: ThreadRange: Type: Temp Temp Range: Current Colors: Current Colors: Current Colors: Nylon 66 (UL Approved Approved 94V-2) 94V-2) UL 94V-2(UL Nylon 66 (UL Approved Approved 94V-2) 94V-2) UL 94V-2(UL Metric , PG, NPT UL 94V-2(UL Approved 94V-2) Metric , PG, NPT Static: - 40°C ∼ +100°C Metric , PG, NPT - 40°C ∼ +100°C Static: Dynamic: - 20°C ∼ + 80°C Static: - 20°C 40°C ∼ ∼+ +100°C Dynamic: -+120°C 80°C Short Term: Dynamic: -+120°C 20°C ∼ + 80°C Short Term: Gray, Black Short Term: +120°C Gray, Black Gray, Black Nylon Cable Glands Nylon Cable Glands Max ”d” AIGO Part Cable Thread “A” Nylon Glands (mm) Max ”d” AIGO Part Thread “A” AIO-CSM12 AIGO Part AIO-CSM12 AIO-CSM16 AIO-CSM12 AIO-CSM16 AIO-CSM18 AIO-CSM16 AIO-CSM18 AIO-CSM20 AIO-CSM18 AIO-CSM20 AIO-CSM22 AIO-CSM20 AIO-CSM22 AIO-CSM24 AIO-CSM22 AIO-CSM24 AIO-CSM25 AIO-CSM24 AIO-CSM25 AIO-CSM30 AIO-CSM25 AIO-CSM30 AIO-CSM32 AIO-CSM30 AIO-CSM32 AIO-CSM33 AIO-CSM32 AIO-CSM33 AIO-CSM40 AIO-CSM33 AIO-CSM40 AIO-CSM50 AIO-CSM40 AIO-CSM50 AIO-CSM72 AIO-CSM50 AIO-CSM72 AIO-CSIN1/2 AIO-CSM72 AIO-CSIN1/2 AIO-CSIN3/4 AIO-CSIN1/2 AIO-CSIN3/4 AIO-CSIN5/4 AIO-CSIN3/4 AIO-CSIN5/4 AIO-CSIN3/2 AIO-CSIN5/4 AIO-CSIN3/2 AIO-CSGIN1/2 AIO-CSIN3/2 AIO-CSGIN1/2 AIO-CSGIN3/4 AIO-CSGIN1/2 AIO-CSGIN3/4 AIO-CSGIN1 AIO-CSGIN3/4 AIO-CSGIN1 AIO-CSGIN5/4 AIO-CSGIN1 AIO-CSGIN5/4 AIO-CSGIN3/2 AIO-CSGIN5/4 AIO-CSGIN3/2 AIO-CSGIN5/2 AIO-CSGIN3/2 AIO-CSGIN5/2 AIO-CSPG7 AIO-CSGIN5/2 AIO-CSPG7 AIO-CSPG9 AIO-CSPG7 AIO-CSPG9 AIO-CSPG11 AIO-CSPG9 AIO-CSPG11 AIO-CSPG13.5 AIO-CSPG11 AIO-CSPG13.5 AIO-CSPG16 AIO-CSPG13.5 AIO-CSPG16 AIO-CSPG21 AIO-CSPG16 AIO-CSPG21 AIO-CSPG29 AIO-CSPG21 AIO-CSPG29 AIO-CSPG36 AIO-CSPG29 AIO-CSPG36 AIO-CSPG42 AIO-CSPG36 AIO-CSPG42 AIO-CSPG42 Metal Cable Glands Metal Cable Glands Metal Glands Material:Cable Brass with Nickel; Brass with Tin/Nickel M12x1.5 M12x1.5 M16x1.5 M12x1.5 M16x1.5 M18 1.5 M16x1.5 M18 M20 1.5 M18 1.5 M20 M22 M20 1.5 M22 M24 M22 M24 1.5 M25x1.5 M24 1.5 M25x1.5 M30 2.0 M25x1.5 M30 2.0 M32 1.5 M30 2.0 M32 1.5 M33 M32 1.5 M33 2.0 M40 M33 2.0 M40 M50 1.5 M40 M50 1.5 M72 2.0 M50 1.5 M72 2.0 NPT1/2” M72 2.0 NPT1/2” NPT3/4” NPT1/2” NPT3/4” NPT1”1/4” NPT3/4” NPT1”1/4” NPT1”1/2” NPT1”1/4” NPT1”1/2” G1/2” NPT1”1/2” G1/2” G3/4” G1/2” G3/4” G1” G3/4” G1” G1”1/4” G1” G1”1/4” G1”1/2” G1”1/4” G1”1/2” G2”1/2” G1”1/2” G2”1/2” PG7 G2”1/2” PG7 PG9 PG7 PG9 PG11 PG9 PG11 PG13.5 PG11 PG13.5 PG16 PG13.5 PG16 PG21 PG16 PG21 PG29 PG21 PG29 PG36 PG29 PG36 PG42 PG36 PG42 PG42 Thread “A” (mm) 8 ”d” Max (mm) 8 Cable Range (mm) Cable Range 3(mm) – Range 6.5 Cable (mm) 34––6.5 8 Thread “L” (mm)“L” Thread (mm) 8 “L” Thread (mm) 8 8 10 8 10 12 10 12 14 12 14 14 18 14 18 18 25 18 25 25 32 25 32 38 32 38 57 38 57 12 57 12 18 12 18 32 18 32 32 12 32 12 18 12 18 25 18 25 28 25 28 32 28 32 57 32 57 6.5 57 6.5 8 6.5 8 10 8 10 12 10 12 14 12 14 18 14 18 25 18 25 32 25 32 38 32 38 38 354––6.5 8 10 8 54––12 10 6 5 ––12 10 6 10 14 6 ––12 10 14 10 13 – 14 18 10 – 18 14 13 13 – 25 18 18 13 – 25 18 18 18 – 32 25 22 18 – 38 25 22 32 32 22 32 – 32 38 51 57 32 38 51 57 6 ––12 51 57 6 ––12 13 18 6 ––12 13 18 22 32 13 – 32 18 22 22 32 6 ––12 22 32 6 ––12 13 18 6 ––12 13 18 18 25 13 – 28 18 18 25 21 18 – 32 25 21 28 22 21 – 57 28 22 32 51 22 32 51 57 3 ––6.5 51 57 34––6.5 8 354–––6.5 8 10 8 54––12 10 6 5 ––12 10 6 10 14 6 ––12 10 14 13 18 10 – 25 14 13 18 18 13 – 32 18 18 25 22 18 – 38 25 22 32 32 22 – 38 32 32 32 – 38 8 9 8 9 9 10 9 10 10 10 11 10 11 11 11 13 11 13 14 13 14 16 14 16 13.6 16 13.6 14.1 13.6 14.1 17.3 14.1 17.3 17.3 9 17.3 9 11 9 11 11 13 11 13 13 14 13 14 8 14 8 8 8 9 8 9 10 9 10 11 10 11 11 13 11 13 14 13 14 14 Material: Brass with Nickel; Clamping: UL approved PA6, Brass 94V-0with Tin/Nickel Material: Brass with Nickel; Brass with Tin/Nickel Clamping: UL approved 94V-0NBR, Seal Ring: UL 94V-2 (ULPA6, approved 94V-2;UL approved Clamping: UL approved PA6, 94V-0NBR, 94V-2;UL approved Seal Ring: UL 94V-2 (UL approved DOW CORNING RUBBER, 94V-0 Seal Ring: UL 94V-2 (UL approved NBR, 94V-2;UL approved DOW Thread Type: Metric,CORNING PG, NPT RUBBER, 94V-0 DOW CORNING RUBBER, 94V-0 Thread Type: Metric, PG, NPT Protective: IP68 (tighten with o-ring) Thread Type: Metric, PG, NPT Protective: (tighten with o-ring) Temp Range: IP68 - 40°C ∼ +100°C Protective: IP68 (tighten with o-ring) Temp - 40°C ∼ +100°C TorqueRange: Value (N-M) to tighten the fitting to the flexible cord: 6.25N-M Temp Range: - 40°C ∼ +100°C Torque Value (N-M) to tighten the fitting to to the the threaded flexible cord: Torque Value (N-M) to tighten the fitting hub:6.25N-M 4.17N-M Torque Value Value (N-M) (N-M) to to tighten tighten the the fitting fitting to to the the threaded flexible cord: 6.25N-M Torque Torque Value (N-M) of hex and capunder nuts: file 3.0-4.5 N-M hub: 4.17N-M M12, M16, M20 are UL recognized # E339605 Torque Value (N-M) to tighten the fitting tofile the#threaded hub: 4.17N-M M12, M16, M20 are UL recognized under E339605 M12, M16, M20 M20 are are UL UL recognized recognizedunder underfile file##E339605 E339605 M12, M16, Metal Cable Glands Metal Cable Glands Max ”d” Cable Range AIGO PartCable Thread “A” Metal Glands (mm) (mm) Max ”d” Cable Range Clamp ”H” Spanner "S" (mm) "S" (mm)”H” Spanner Clamp (mm) (mm) 20 ”H” Spanner 15 "S" Clamp (mm) (mm) 20 15 22 19 20 22 25 22 25 30 25 30 30 30 30 33 30 33 38 33 38 39 38 39 48 39 48 50 48 50 75 50 75 28 75 28 32 28 32 46 32 46 50 46 50 26 50 26 27 26 27 33 27 33 48 33 48 48 75 48 75 20 75 20 22 20 22 24 22 24 26 24 26 28 26 28 33 28 33 38 33 38 48 38 48 52 48 52 52 AIGO Part AIO-CSJM12 AIGO Part AIO-CSJM12 AIO-CSJM14 AIO-CSJM12 AIO-CSJM14 AIO-CSJM16 AIO-CSJM14 AIO-CSJM16 AIO-CSJM18 AIO-CSJM16 AIO-CSJM18 AIO-CSJM20 AIO-CSJM18 AIO-CSJM20 AIO-CSJM22 AIO-CSJM20 AIO-CSJM22 AIO-CSJM24 AIO-CSJM22 AIO-CSJM24 AIO-CSJM25 AIO-CSJM24 AIO-CSJM25 AIO-CSJM27 AIO-CSJM25 AIO-CSJM27 AIO-CSJM30 AIO-CSJM27 AIO-CSJM30 AIO-CSJM32 AIO-CSJM30 AIO-CSJM32 AIO-CSJM36 AIO-CSJM32 AIO-CSJM36 AIO-CSJM40 AIO-CSJM36 AIO-CSJM40 AIO-CSJM50 AIO-CSJM40 AIO-CSJM50 AIO-CSJM63 AIO-CSJM50 AIO-CSJM63 AIO-CSJM72 AIO-CSJM63 AIO-CSJM72 AIO-CSJM80 AIO-CSJM72 AIO-CSJM80 AIO-CSJM90 AIO-CSJM80 AIO-CSJM90 AIO-CSJIN1/2 AIO-CSJM90 AIO-CSJIN1/2 AIO-CSJIN3/4 AIO-CSJIN1/2 AIO-CSJIN3/4 AIO-CSJIN5/4 AIO-CSJIN3/4 AIO-CSJIN5/4 AIO-CSJIN3/2 AIO-CSJIN5/4 AIO-CSJIN3/2 AIO-CSJIN2 AIO-CSJIN3/2 AIO-CSJIN2 AIO-CSJIN5/2 AIO-CSJIN2 AIO-CSJIN5/2 AIO-CSJIN3 AIO-CSJIN5/2 AIO-CSJIN3 AIO-CSJGIN1/2 AIO-CSJIN3 AIO-CSJGIN1/2 AIO-CSJGIN3/4 AIO-CSJGIN1/2 AIO-CSJGIN3/4 AIO-CSJGIN1 AIO-CSJGIN3/4 AIO-CSJGIN1 AIO-CSJGIN5/4 AIO-CSJGIN1 AIO-CSJGIN5/4 AIO-CSJGIN3/2 AIO-CSJGIN5/4 AIO-CSJGIN3/2 AIO-CSJGIN2 AIO-CSJGIN3/2 AIO-CSJGIN2 AIO-CSJGIN5/2 AIO-CSJGIN2 AIO-CSJGIN5/2 AIO-CSJGIN3 AIO-CSJGIN5/2 AIO-CSJGIN3 AIO-CSJPG7 AIO-CSJGIN3 AIO-CSJPG7 AIO-CSJPG9 AIO-CSJPG7 AIO-CSJPG9 AIO-CSJPG11 AIO-CSJPG9 AIO-CSJPG11 AIO-CSJPGM16 AIO-CSJPG11 AIO-CSJPGM16 AIO-CSJPG13.5 AIO-CSJPGM16 AIO-CSJPG13.5 AIO-CSJPG16 AIO-CSJPG13.5 AIO-CSJPG16 AIO-CSJPG21 AIO-CSJPG16 AIO-CSJPG21 AIO-CSJPG36 AIO-CSJPG21 AIO-CSJPG36 AIO-CSJPG42 AIO-CSJPG36 AIO-CSJPG42 AIO-CSJPG48 AIO-CSJPG42 AIO-CSJPG48 AIO-CSJPG48 15 19 22 19 22 24 22 24 27 24 27 27 33 27 33 33 42 33 42 42 54 42 54 60 54 60 80 60 80 24 80 24 33 24 33 54 33 54 54 24 54 24 33 24 33 42 33 42 54 42 54 54 80 54 80 15 80 15 19 15 19 22 19 22 24 22 24 27 24 27 33 27 33 42 33 42 54 42 54 60 54 60 60 For additional information on other products available For additional information on other products available Grips & Cable Glands, Catalog 12-055. refer to our Cord For additional information on other products available refer to our Cord Grips & Cable Glands, Catalog 12-055. refer to our Cord Grips & Cable Glands, Catalog 12-055. 41 Thread “A” M12x1.5 Thread “A” M12x1.5 M14x1.5 M12x1.5 M14x1.5 M16x1.5 M14x1.5 M16x1.5 M18x1.5 M16x1.5 M18x1.5 M20x1.5 M18x1.5 M20x1.5 M22 1.5 M20x1.5 M22 M24 1.5 M22 1.5 M24 M25x1.5 M24 1.5 M25x1.5 M27 2.0 M25x1.5 M27 M30 2.0 M27 2.0 M30 M32 1.5 M30 2.0 M32 1.5 M36 M32 1.5 M36 2.0 M40 M36 2.0 M40 M50 1.5 M40 1.5 M50 M63 M50 1.5 M63 M72 2.0 M63 M72 2.0 M80 1.5 M72 2.0 M80 M90 M80 2.0 M90 NPT1/2” M90 2.0 NPT1/2” NPT3/4” NPT1/2” NPT3/4” NPT1”1/4” NPT3/4” NPT1”1/4” NPT1”1/2” NPT1”1/4” NPT1”1/2” NPT2” NPT1”1/2” NPT2” NPT2 1/2” NPT2” NPT2 1/2” NPT3” NPT2 1/2” NPT3” G1/2” NPT3” G1/2” G3/4” G1/2” G3/4” G1” G3/4” G1” G1”1/4” G1” G1”1/4” G1”1/2” G1”1/4” G1”1/2” G2” G1”1/2” G2” G2 1/2” G2” G2 1/2” G3” G2 1/2” G3” PG7 G3” PG7 PG9 PG7 PG9 PG11 PG9 PG11 M16x1.5 PG11 M16x1.5 PG13.5 M16x1.5 PG13.5 PG16 PG13.5 PG16 PG21 PG16 PG21 PG36 PG21 PG36 PG42 PG36 PG42 PG48 PG42 PG48 PG48 (mm) 6.5”d” Max (mm) 6.5 8 3(mm) – Range 6.5 Cable 3(mm) 4––6.5 8 Thread “L” (mm)“L” Thread (mm) 6.2 “L” Thread (mm) 6.2 5 6.5 8 9 8 9 10 9 10 12 10 12 14 12 14 14 18 14 18 18 18 25 18 25 25 32 25 32 38 32 38 44 38 44 52 44 52 60 52 60 70 60 70 12 70 12 18 12 18 32 18 32 32 44 32 44 52 44 52 70 52 70 12 70 12 18 12 18 25 18 25 32 25 32 32 44 32 44 52 44 52 70 52 70 6.5 70 6.5 8 6.5 8 10 8 10 10 12 10 12 14 12 14 18 14 18 32 18 32 38 32 38 44 38 44 44 36 4––6.5 8 9 4––10 8 9 56 9 56––12 10 6 5 ––12 10 6 10 14 6 ––12 10 14 10 13 – 14 18 10 – 18 14 13 13 – 18 13 – 25 18 18 13 – 25 18 18 18 22 – 25 32 18 – 38 25 22 32 32 22 – 44 32 32 38 37 32 – 52 38 37 44 46 37 44 46 52 – 52 60 46 52 – 52 60 62 70 52 60 62 70 6 ––12 62 70 6 ––12 13 18 6 ––12 13 18 22 32 13 – 32 18 22 22 37 – 32 44 22 – 52 32 37 44 46 37 – 70 44 46 52 62 46 52 62 70 6 ––12 62 70 6 ––12 13 18 6 ––12 13 18 18 25 13 – 32 18 18 25 22 18 – 32 25 22 22 – 44 32 37 22 – 52 32 37 44 46 37 46 – 44 52 62 70 46 52 62 70 3 ––6.5 62 70 34––6.5 8 354–––6.5 8 10 810 54–––10 6.2 5 6.2 10 6 ––10 12 6.2 10 6 –––12 10 14 6 ––12 10 14 13 18 10 – 32 14 13 18 22 13 – 38 18 22 32 32 22 – 44 32 32 38 37 32 – 44 38 37 37 – 44 6.2 5 6.3 5 6.3 7 6.3 7 8.3 7 8.3 8 8.3 8 8 7.8 7.8 8 7.8 8 8 10 8 10 10 10 11 10 11 12 11 12 16 12 16 20 16 20 20 13.6 20 13.6 14.1 13.6 14.1 17.3 14.1 17.3 17.3 17.7 17.3 17.7 23.7 17.7 23.7 26 23.7 26 8 26 8 8 10 8 10 10 10 12 10 12 16 12 16 20 16 20 6 20 6 7 6 7 7 6.5 7 6.5 8 6.5 8 8 8 10 8 10 11 10 11 12 11 12 12 Clamp ”H” Spanner "S" (mm)”H” Spanner (mm) "S" Clamp (mm) (mm) 15 ”H” Spanner 14 "S" Clamp (mm) (mm) 15 14 19 15 15 19 20 19 20 20 20 24 20 24 24 23 24 23 26 23 26 26 27 26 27 34 27 34 39 34 39 39 43 39 43 47 43 47 57 47 57 57 25 57 25 26 25 26 41 26 41 46 41 46 46 58 46 58 58 24 58 24 27 24 27 34 27 34 39 34 39 39 44 39 44 47 44 47 55 47 55 18 55 18 21 18 21 20 21 20 22 20 22 24 22 24 25 24 25 26 25 26 38 26 38 42 38 42 44 42 44 44 14 15 18 15 18 22 18 22 22 24 22 24 27 24 27 30 27 30 30 32 30 32 40 32 40 40 50 40 50 60 50 60 67 60 67 75 67 75 90 75 90 100 90 100 24 100 24 30 24 30 50 30 50 50 65 50 65 80 65 80 100 80 100 24 100 24 30 24 30 40 30 40 50 40 50 50 65 50 65 82 65 82 100 82 100 14 100 14 18 14 18 22 18 22 20 22 20 20 22 24 22 24 30 24 30 50 30 50 60 50 60 65 60 65 65 Application Tools “SE” The following data includes information pertaining to the application tools for crimping, insert­ing and removing size 20, 16, and 12 contacts incorporated in Amphenol® Miniature Cylindri­cal Connectors. All crimping tools included are the “full cycling” type, and when used as specified by the manu­facturer, provide reliable crimped wire to contact termination. Tool frames and turret heads are available from approved tool manufacturers; consult Amphe­nol, Sidney, NY for listings. Assembly instructions are available online at www.amphenol-industrial.com See the following: L-786 for SE assembly instructions L-555 for solder type instructions CRIMPING TOOLS FOR PT-SE, SP-SE, MS/PT-SE (MIL-DTL-26482, Series 1) Connectors MS Tool Part Number Contact Size Tool Frame Turret Head 20 M22520/1-01 M22520/1-02 16 M22520/1-01 M22520/1-02 12 M22520/1-01 M22520/1-02 INSERTION/REMOVAL TOOLS FOR PT-SE, SP-SE, MS/PT-SE (MIL-DTL-26482, Series 1) Connectors Insertion Tool Amphenol® Contact Contact Size Insertion Pliers Removal Tool Amphenol® Contact Insertion Tool MS Part Number Contact Insertion Tool Amphenol® Contact Removal Tool MS Part Number Contact Removal Tool 20 11-8107-20 11-7401-20 M81969/17-03 11-7880-20 M81969/19-07 16 11-8107-16 11-7401-16 M81969/17-04 11-7880-16 M81969/19-08 12 – – M81969/17-05 – M81969/19-09 42 Contacts - Power and Thermocouple Crimp for miniature cylindrical connectors The following tables provide part number information for crimp contacts used in Amphenol® Miniature Cylindrical Connectors. For additional infor­ mation, consult Amphenol, Sidney, NY. CRIMP CONTACTS for MIL-DTL-26482, Series 1 (PT-SE, SP-SE) Connectors Pins Contact Size Accommodates Wire Size MS Number Sockets Amphenol® Proprietary Number MS Number Amphenol® Proprietary Number 20 20, 22 & 24 AWG M39029/31-240 10-683787-20P M39029/32-259 10-731210-3D1 16 16, 18 & 20 AWG M39029/31-228 10-683788-16P M39029/32-247 10-679379-16D 12 12 & 14 AWG 20-16 16 AWG 10-330930-20F 10-807155-205 16-20 20 AWG 10-330932-16F 10-330933-16F 12-10 12 AWG 10-330938-12F 10-330939-12F M39029/31-235 10-807100-125 M39029/32-254 10-807103-125 THERMOCOUPLE CONTACTS for Miniature Connectors Size 16 Crimp Termination Pins Proprietary Part Number Sockets Proprietary Part Number SE SE Chromel 10-330940-21P 10-330940-21S Alumel 10-330940-22P 10-330940-22S Alumel 10-330940-2P 10-330940-2S Iron 10-330940-3P 10-330940-3S Constantan 10-330940-4P 10-330940-4S Material Chromel 20 Crimp Termination 10-330940-1P 10-330940-1S See L-776 for thermocouple contact termination instructions. These are online at www.amphenol-industrial.com For PCB contacts for miniature connectors, see page 20. 43 Coaxial Contacts for miniature cylindrical connectors Amphenol® Miniature Connectors can incorporate shielded coax contacts. The Miniature family is built around MIL-DTL-26482 specifications, with Milapproved and proprietary styles offered. Normal operating voltage for Minia­ture cylindricals with power only contacts is up to 1,000 VAC (RMS) at sea level. Table 1: Miniature Cylindricals offer these features for contact termination flexibility: • Several insert arrangements that can incorporate: • Size 8 & 12 Crimp Coax contacts for Crimp type • Size 8 & 12 Solder Coax contacts for Solder type • Wide selection of connector shell styles and sizes • Standard power contact options within the various connector styles include: solder type, crimp front release, crimp rear release • Coax contacts are designed to the same high performance standards as power contacts. Coax and power contacts may be intermixed with no deg­radation of connector reliability. • No mis-mating or cross-plugging with insert rotation and keyway polarization. Table 2: GENERAL ORDERING INFORMATION Amphenol Miniature Cylindricals are normally supplied with a full complement of power contacts, separately packaged. Coax contacts are ordered by part number as referenced in the part number charts on the following pages of this catalog, and are substituted for the power contacts at the time of the cable or equipment assembly. If the application is for coax only, the connector may be ordered less contacts and no power contacts will be supplied. Installation instructions for the coax contacts for Miniature Connectors are provided in Amphenol documents as follows: L-633 for solder type; L-613 for SE type. HOW TO ORDER: A. Select the coax contacts designed for the cable being used from the appli­cable charts in this catalog for each Miniature type (solder, SE). B. Select a connector insert from those shown on pages 4-5 which will accommodate the quantity and size of coaxial contacts needed plus any power contacts required. Note: Size 8S and 12S contacts are used with connector inserts through shell size 18 only. For larger connector shell sizes, use size 8L contacts. C. Determine the Miniature Cylindrical type, shell style, finish, service class and insert rotation required for your application. D. Consult Amphenol, Sidney NY with the pertinent cable, contact, insert arrangement and connector style choices for complete connector part number. 44 Solder Coax Contact for use in Miniature Solder Type Connectors Pin Crimp Coax Contact for use in Miniature Crimp SE Type Connectors Socket Crimp Coax Contact for use in Miniature Crimp SE Type Connectors Coaxial Contacts for miniature cylindrical connectors, cont. Amphenol Coaxial Contacts designed for use in Miniature Cylindrical Connectors ® offer the same durability advantages and design benefits for reliable interconnection as the Amphenol coax contacts used in high performance D38999 connectors. A variety of military and commercial shielded cables are accommodated within the miniature cylindrical series. Amphenol supplies coax contacts for solder and crimp SE connector styles. Other features of the coax for miniature cylindricals include: • Miniature coax design has an outside nut within the assembly for fast, reliable assembly of contact to cable. • All types feature solder style inner contacts and crimp style outer contacts for reliable cable termination TYPICAL MINIATURE CRIMP COAX SOCKET CONTACT has crimp socket outer contact with a solder pin inner contact • Miniature coax crimp type contacts are designed for use in Miniature crimp series connectors • Miniature coax solder type contacts are designed for use in Miniature solder series connectors. These come pre-installed into the solder connector. TYPICAL ELECTRICAL PERFORMANCE Size 8 and 12 Coax Contacts Contact Resistance: Center @ 1 Amp, 170 millivolts max. voltage drop @ 25°C Outer @ 12 Amps, 150 millivolts max. voltage drop @ 25°C Dielectric Withstanding Voltage: TYPICAL MINIATURE CRIMP COAX PIN CONTACT has crimp pin outer contact with a solder socket inner contact Size 8: 1,300 VAC Rms @ sea level Size 12: 1,000 VAC Rms @ sea level Size 8 & 12: 250 VAC Rms @ 50,000 ft. Insulation Resistance 5,000 megohms minimum @ 25°C Typical VSWR for size 8 & 12 PT-SE Types II & III only: 1.2 +  .12F (GHz) up to 10 GHz EXPLANATION OF TYPE CLASSIFICATIONS: PT-SE Type I is moisture seal design with internal O-ring. PT-SE Type II is 50 ohm impedance matched version. Contacts termi­nated to other than 50 ohm cables are therefore not matched. PT-SE Type III is 50 ohm contact, non-serviceable after assembly. Solders are non-impedance matched contacts. CONTACT FINISHES: Suffix    Finish 1 0.00020 min. silver over copper flash 2 0.00005 min. gold (Knoop hardness 130-200) over silver 3 0.00010 min. gold (Knoop hardness 130-200) over silver 4 0.00010 min. gold (Knoop hardness 130-200) over copper 5 0.00005 min. gold (Knoop hardness 130-200) over nickel E 0.00005 min. gold (Knoop hardness 90 max.) over copper F 0.00005 min. gold (Knoop hardness 130-200) over copper H 0.00010 min. gold (Knoop hardness 130-200) over copper 45 Coaxial Contacts for miniature cylindrical connectors, cont. solder (MIL-DTL-26482 Series 1 type) - application data MATING PIN DIA L H F G SOCKET L H F G MATING PIN DIA PIN NOTE: All contacts of the same size and the same inner and outer contact diameters (G & H) will mate with each other. SOLDER COAX CONTACTS For use in Miniature Solder Type Connectors: PT, SP, and MS/PT Styles Dimensional Data (See Drawings above) Contact Part Number Contact Size Cable G Dia. F H Across Dia. Flats ±0.001 ±0.004 Socket 21-33020-2 21-33019-2 8S 0.040 ± 0.001 0.219 0.280 1.114 1.115 21-33020-1 21-33019-1 8L 0.040 ± 0.001 0.219 0.280 1.176 1.177 21-33020-3 21-33019-3 8S 0.040 ± 0.001 0.219 0.280 1.114 1.115 RG-142B/U, Times MI51115 21-33020-7* 21-33019-7* 8S 0.040 ± 0.001 0.219 0.280 1.114 RG-161/U, RG-174A/U, RG-179B/U, RG-187A/U, RG-188A/U, RG-316/U 21-33020-32* 21-33019-32* 12S 0.0300 ± 0.0005 0.140 0.172 RG-59B/U, RG-62A/U, RG-62B/U, RG-210/U Pin Retainer Nut MIL-T-22910/7-1 MIL-C-22520/5-01 MIL-C-22520/10-01 Wrench Tool Tool Tool Socket Use with Die Part Use with Die Part Use with Die Part Number Number Number Pin RG-58C/U, RG-141A/U, RG-303/U Crimp Ferrule Tools L Length Ref. M22910/7-15 (B) M22520/5-05 (B) M22520/5-41 (B) M22910/7-18 (B) M22520/5-45 (B) 11-8676-3 1.115 M22910/7-16 (B) M22520/5-43 (B) 11-8676-2 1.092 1.093 M22910/7-12 (B) M22520/5-03 (A) M22520/5-08 (A) M22520/5-35 (B) M22520/10-05 (A) 11-8676-1 M22520/10-07 (B) 11-8676-2 RG-178B/U 21-33020-4 21-33019-4* 8S 0.040 ± 0.001 0.219 0.280 1.114 1.115 M22910/7-11 (B) M22520/5-03 (B) M22520/5-33 (B) M22520/10-05 (B) 11-8676-2 RG-196A/U 21-33020-31† 21-3306131*† 12S 0.0300 ± 0.0005 0.140 0.172 1.092 1.093 M22910/7-11 (B) M22520/5-03 (B) M22520/5-33 (B) M22520/10-05 (B) 11-8676-1 RG-180B/U, RG-195A/U, Raychem  5022D1312-9 21-33020-5* 21-33019-5* 8S 0.040 ± 0.001 0.219 0.280 1.114 1.115 M22910/7-15 (B) M22520/5-05 (B) M22520/5-41 (B) M22520/10-07 (B) 11-8676-2 Raychem  5021D1331-9 21-33020-6* 21-33019-6* 8S 0.040 ± 0.001 0.219 0.280 1.114 1.115 M22910/7-15 (B) M22520/5-05 (B) M22520/5-41 (B) M22520/10-07 (B) 11-8676-2 Thermatics  2929-29 21-33020-33 21-33061-33 12S 0.0200 ± 0.0005 0.140 0.172 1.092 1.093 M22910/7-13 (B) M22520/5-37 (B) NOTE: Contacts can be ordered by part numbers given in chart NOTE: Size 8S and 12S contacts are used with connector inserts through shell size 18 only. For larger connector shell sizes, use size 8L contacts. CONTACT FINISH: For all contacts in this series feature 0.000050 minimum gold (Knoop hardness 130-200). 11-8676-1 * Consult Amphenol, Sidney NY for availability CRIMPING TOOLS: Italicized letters in parenthesis that follow positioner part numbers indicate applicable die closure. Commercial equivalents with the same die closure dimension may be used. † 21-33020-31 and 21-33061-31 only mate with each other 46 Coaxial Contacts for miniature cylindrical connectors, cont. crimp SE (MIL-DTL-26482 Series 1 type) - application data L F L G H H MATING PIN DIA SOCKET G MATING PIN DIA F PIN NOTE: All contacts of the same size and the same inner and outer contact diameters (G & H) will mate with each other. SE CRIMP COAX CONTACTS For use in Miniature Crimp Type Connectors: PT-SE, SP-SE, and MS/PT-SE Styles Contact Part Number Cable RG-55B/U, RG-142A/U, RG-142B/U, RG-223/U RG-58C/U, RG-141A/U, RG-303/U RG-59B/U, RG-62A/U, RG-62B/U, RG-210/U RG-140/U, RG-302/U Finish Contact on Type Size Mating Parts Pin Socket 21-33012-21 21-33012-25 21-33011-21 21-33011-25 8 8 I II 2 21-33038-21 21-33038-25* 21-33037-21 21-33037-25 8 8 I II 4 8 8 I II ** 21-33138-21( )* 21-33137-21( )* 21-33138-25( )* 21-33137-25( )* 21-33012-22 21-33012-26 21-33011-22 21-33011-26 8 8 I II 2 21-33038-22* 21-33038-26* 21-33037-22 21-33037-26* 8 8 I II 4 8 8 I II ** 21-33138-22( )* 21-33137-22( ) 21-33138-26( )* 21-33137-26( )* 21-33012-36 21-33011-36 8 II 2 21-33038-36* 21-33037-36 8 II 4 21-33138-36( )* 21-33137-36( ) 8 II ** 21-33012-37* 21-33011-37* 8 II 2 21-33038-37* 21-33037-37* 8 II 4 21-33138-37( )* 21-33137-37( )* 8 II ** 21-33012-34 21-33012-30 21-33011-34 21-33011-30 8 8 I II 2 21-33038-34 21-33038-30 21-33037-34 21-33037-30 8 8 I II 4 21-33137-34( )* 21-33137-30( )* 8 8 I II ** 21-33011-1 21-33011-4 12 12 I II 2 21-33037-1* 21-33037-4* 12 12 I II 4 21-33138-1( )* 21-33137-1( ) 21-33138-4( )* 21-33137-4( )* 12 12 I II ** 21-33012-35 21-33011-35 8 I 2 21-33038-35 21-33037-35 8 I 4 RG-161/U, RG-174A/U, 21-33138-34( )* RG-179B/U, 21-33138-30( )* RG-187A/U, 21-33012-1 RG-188A/U, 21-33012-4 RG-316/U 21-33038-1* 21-33038-4 21-33138-35( )* 21-33137-35( )* RG-178B/U, RG-196A/U Dimensional Data (See Drawings above) 8 I ** 21-33012-3* 21-33012-5 21-33011-3* 21-33011-5 12 12 I II 2 21-33038-3* 21-33038-5 21-33037-3* 21-33037-5* 12 12 I II 4 12 12 I II ** 21-33138-3( )* 21-33137-3( )* 21-33138-5( )* 21-33137-5( )* G Dia. Installation Tools Crimp Ferrule Tools L Length Ref. F H Across MIL-T-22910/7-1 MIL-C-22520/5-01 MIL-C-22520/10-0 Dia. Flats Tool Tool Tool ±0.001 Pin Socket ±0.004 Use with Die Part Use with Die Part Use with Die Part Number Number Number Retainer Nut Wrench Insertion Removal 0.0355 M22520/5-05 (A) 0.218 0.280 1.156 1.144 M22910/7-17 (B) ±0.0010 M22520/5-19 (B) M22520/10-07 (A) 11-8676-2 11-8369-5 11-7880-8 11-8660-5 11-8154-1 0.0355 M22520/5-05 (B) 0.218 0.280 1.156 1.144 M22910/7-15 (B) ±0.0010 M22520/5-41 (B) M22520/10-07 (B) 11-8676-2 11-8369-4 11-7880-8 11-8660-4 11-8154-1 0.0355 0.218 0.280 1.156 1.144 M22910/7-18 (B) M22520/5-45 (B) ±0.0010 11-8676-3 11-8369-5 11-7880-8 11-8660-5 11-8154-1 0.0355 M22520/5-05 (A) 0.218 0.280 1.156 1.144 M22910/7-17 (B) ±0.0010 M22520/5-19 (B) M22520/10-07 (A) 11-8676-2 11-8369-5 11-7880-8 11-8660-5 11-8154-1 11-8676-2 11-7880-8 11-8154-1 0.0355 0.218 0.280 1.156 1.144 ±0.0010 M22520/5-03 (A) M22910/7-12 (B) M22520/5-08 (A) M22520/5-35 (B) 11-8369-2 11-8660-2 M22520/10-05 (A) 0.0200 0.128 0.172 1.092 1.072 ±0.0005 11-8676-1 11-7880-12 11-8154-2 0.0355 0.218 0.280 1.156 1.144 ±0.0010 11-8676-2 11-7880-8 11-8154-1 M22910/7-11 (B) 0.0200 0.128 0.172 1.092 1.072 ± 0.0005 NOTE: Contacts can be ordered by part numbers given in chart ** See finish options for SE crimp Miniature contacts listed on page 44. Replace the paren­thesis of the contact part number with the finish suffix number. However, you should con­sult Amphenol, Sidney, NY regarding the availability of all finish choices for each part number. * Consult Amphenol, Sidney NY for availability 47 M22520/5-03 (B) M22520/5-33 (B) 11-8369-1 11-8660-1 M22520/10-05 (A) 11-8676-1 11-7880-12 11-8154-2 CRIMPING TOOLS: Italicized letters in parenthesis that follow positioner part numbers indicate applicable die closure. Commercial equivalents with the same die closure dimen­sion may be used. CHART CONTINUES ON NEXT PAGE Coaxial Contacts for miniature cylindrical connectors, cont. crimp SE (MIL-MDL-26482 Series 1 type) - application data, cont. NOTE: All contacts of the same size and the same inner and outer contact diameters (G & H) will mate with each other. SE CRIMP COAX CONTACTS For use in Miniature Crimp Type Connectors: PT-SE, SP-SE, and MS/PT-SE Styles Dimensional Data Contact Part Number Cable Finish on Contact Type Size Mating Parts Pin Socket 21-33012-24 21-33012-46* 21-33011-24 21-33011-46* 8 8 I II 2 21-33038-24 21-33038-46* 21-33037-24 21-33037-46* 8 8 I II 4 21-33138-24( )* 21-33137-24( )* 21-33138-46( )* 21-33137-46( )* 8 8 I II ** Raychem  9527E1118, 21-33106-40( ) 21-33105-40( ) RG-180B/U, RG-195A/U 12 III ** RG-180B/U, RG-195A/U RG-188 or RG-316 Double Braid Thermax 50C-25ADS-1 21-33012-6* 21-33012-7* 21-33011-6* 21-33011-7* 12 12 I II 2 21-33038-6* 21-33038-7* 21-33037-6* 21-33037-7* 12 12 I II 4 21-33138-6( )* 21-33137-6( )* 21-33138-7( )* 21-33137-7( )* 12 12 I II ** 21-33012-44 21-33011-44 8 II 2 21-33038-44* 21-33037-44* 8 II 4 8 II ** 8 I 2 8 I 4 21-33138-44( )* 21-33137-44( )* 21-33012-28 21-33011-28 RG-195 21-33038-28* 21-33037-28* Double Braid 21-33138-28( )* 21-33137-28( )* 8 I ** 21-33011-23 21-33011-27 8 8 I II 2 21-33037-23* 21-33037-27 8 8 I II 4 21-33137-23( )* 21-33137-27( )* 8 8 I II ** 21-33012-31 21-33011-31 Raychem 21-33038-31 21-33037-31  9530D5314 21-33138-31( )* 21-33137-31( )* 8 I 2 8 I 4 8 I ** 21-33012-39 21-33011-39 Raychem 21-33038-39* 21-33037-39*  9527A1317 21-33138-39( )* 21-33137-39( )* 8 II 2 8 II 4 8 II ** 8 II 2 8 II 4 21-33012-23 21-33012-27 RG-122/U, 21-33038-23* Raychem 21-33038-27  5022E5111 21-33138-23( )* 21-33138-27( )* 21-33012-40* 21-33011-40 Raychem 21-33038-40* 21-33037-40*  7527A1318 21-33138-40* 21-33137-40( )* Westrex 21-33012-43 21-33011-43 199-49-1, 21-33038-43 21-33037-43 Tensolite 30850/87T-1 21-33138-43( )* 21-33137-43( )* 8 II ** 12 II 2 12 II 4 12 II ** G Dia. F H Across Dia. Flats ±0.001 ±0.004 0.0355 0.218 ± 0.0010 Installation Tools Crimp Ferrule Tools L Length Ref. Pin Retainer Nut MIL-T-22910/7-1 47MIL-C-22520/5-01 MIL-C-22520/10-0 Wrench Tool Tool Tool Socket Use with Die Part Use with Die Part Use with Die Part Number Number Number 0.280 1.156 1.144 M22520/7-15 (B) 0.0200 0.128 ± 0.0005 0.899 0.879 0.0200 0.128 ± 0.0005 0.172 1.092 1.072 M22520/5-05 (B) M22520/5-41 (B) M22520/10-07 (B) 11-8676-2 Daniels GS200 Tool with G2P330 or M22520/31-01 Tool with Positioner M22520/31-02 M22910/7-13 (B) Insertion Removal 11-8369-4 11-7880-8 11-8660-4 11-8154-1 11-8674- 11-7880-12 12 11-8154-2 11-8676-1 11-8369-2 11-7880-12 11-8660-2 11-8154-2 11-8676-2 11-8369-4 11-7880-8 11-8660-4 11-8154-1 M22520/5-37 (B) 0.0355 0.128 ± 0.0010 0.280 1.156 1.144 0.0355 0.128 ± 0.0010 0.280 1.156 1.144 M22910/7-16 (B) M22520/5-43 (B) 11-8676-2 11-8369-4 11-7880-8 11-8660-4 11-8154-1 0.0355 0.218 ± 0.0010 0.280 1.156 1.144 M22520/7-15 (B) M22520/5-05 (B) M22520/5-41 (B) M22520/10-07 (B) 11-8676-2 11-8369-4 11-7880-8 11-8660-4 11-8154-1 0.0355 0.218 ± 0.0010 0.280 1.156 1.144 M22910/7-15 (B) M22520/5-05 (B) M22520/5-41 (B) M22520/10-07 (B) 11-8676-2 11-8369-4 11-7880-8 11-8660-4 11-8154-1 0.0355 0.218 ± 0.0010 0.280 1.156 1.144 M22910/7-12 (B) M22520/5-03 (A) M22520/5-08 (A) M22520/5-35 (B) M22520/10-05 (A) 11-8676-2 11-8369-2 11-7880-8 11-8660-2 11-8154-1 0.0200 0.128 ± 0.0005 0.172 1.092 1.072 M22910/7-11 (B) M22520/5-03 (B) M22520/5-33 (B) M22520/10-05 (B) 11-8676-1 11-8369-1 11-7880-12 11-8660-1 11-8154-2 NOTE: Contacts can be ordered by part numbers given in chart ** See finish options for SE crimp Miniature contacts listed on page 44. Replace the paren­thesis of the contact part number with the finish suffix number. However, you should con­sult Amphenol, Sidney, NY regarding the availability of all finish choices for each part number. * Consult Amphenol, Sidney NY for availability CRIMPING TOOLS: Italicized letters in parenthesis that follow positioner part numbers indi­cate applicable die closure. Commercial equivalents with the same die closure dimension may be used. 48 Mounting Recommendations for miniature cylindrical connectors FLANGE MOUNTED CONNECTORS FLANGE MOUNTED CONNECTORS All flange mounting PT connectors use standard MS mounting dimensions. They cannot be back panel mounted due to coupling clearance. The PTB (thru-bulkhead) type con­nector must also be back panel mounted on one side. Flange gaskets are available for both series, see page 37. Shell Size 6 8 10 12 14 16 18 20 22 24 PT .469 .594 .719 .812 .906 .969 1.062 1.156 1.250 1.375 R (TP) SP .641 .734 .812 .938 1.031 1.125 1.203 1.297 1.375 – PT .323 .449 .573 .699 .823 .949 1.073 1.199 1.323 1.449 D Dia. R 2 R 2 6 8 10 12 14 16 18 20 22 24 .447 .572 .697 .884 1.007 1.134 1.259 1.384 1.507 1.634 B +.000 –.010 .420 .542 .669 .830 .955 1.084 1.208 1.333 1.459 1.575 F ±.010 .286 .331 .375 .442 .486 .530 .573 .641 .685 – P Panel Thickness Min. Max. .062 .062 .062 .062 .062 .062 .062 .062 .062 .062 .125 .125 .125 .125 .125 .125 .125 .250 .250 .250 F OUT PT PANEL CUT R FR B CUT-OUT FOR PT ONLY hermetic seal provided by the glass insert. Mounting data for box and jam nut receptacles is given above. Cut-out required for solder mounting receptacles (N) is given below. 6 8 10 12 14 16 18 20 22 24 .458 .582 .692 .801 .926 1.051 1.176 1.395 1.375 1.520 The finish of each of these hermetic receptacles is fused electro-deposited tin for easy solderability, and protected by a special lacquer for optimum shelf life. The lacquer will not interfere with any soldering operation. Low temperature solder should be used and the addition of a solder fillet at arrow points on drawing at right is rec­ ommended. Care must be taken that the operating temperature of the final assembly does not rise above the melt­ing point of tin (440° F). B F PIN LOCATION FOR PC ONLY CUT-OUT FOR PT ONLY SECTION PIN LOCATION FOR PC ONLY HERMETIC RECEPTACLES This series must be mounted in such a way as to preserve the N Max. F JAM NUT MOUNTINGS HERMETIC RECEPTACLE MOUNTINGS Shell Size SECTION CUT-OUT JAM NUT MOUNTINGS The jam nut design has become very popular because it allows bench wiring of harness assemblies. The labor saving often off­sets the added cost of the jam nut receptacle which is due to the self contained “O” ring and the extra nut. R +.010 –.000 No. 4 Screw No. for 4 PTScrew for PC & PT No. 6 Screw No. 6 Screw forSP SPand andfor for Size24 24PT PT Size D Dia. SP .439 .563 .680 .859 .984 1.108 1.233 1.358 1.483 – JAM NUT MOUNTINGS Shell Size 4 HOLES 4.120 HOLES Dia. for Shell Sizes 6-22 PT .120 Dia. for Shell Sizes 6-22 .147 PC &Dia. PTfor SizeDia. 24 PT .147 for .150 for SizeDia. 24 PT SP only .150 Dia. for SP only R (TP) N CUT-OUT 49 SOLDER RECEPTACLE JAM NUT BOX RECEPTACLE RECEPTACLE (See dimensions (See dimensions above) above) Other Amphenol Miniature Cylindrical Connectors Geophysical Miniature Cylindricals Designed for the Geophysical industry’s rugged environments, the Amphenol® RPT Series connector has custom features that provide reliability in extreme temperature and moisture condi­tions. The unique shell design provides stronger shells along with an anodized (nonconductive) finish for greater salt, corrosion and abrasion resistance. Coupling nuts are manufactured with round detent holes and are sold separately for greater customer flexibil­ity. See product data sheet #146. RJ Field Bayonet Cylindricals Amphenol PCD division provides MIL-DTL-26482 bayonet coupling cylindrical connectors with an RJ45 Ethernet interface*. These are designed for use in all levels of harsh environments from industrial to mil-aero applications providing IP67 protection from dust, fluids, vibration, shock and traction. The Amphenol® RJ Field allows the use of Ethernet Class D/Cat 5 and Cat 5e connections for 10 BaseT, 100 Base TX, or 1000 BaseT networks. It works with any standard RJ45 cordset with no extra tooling. It also offers rein­ forced EMI protection. Amphenol® RPT Miniature Cylindricals For more information go online to www.rjfield.com or ask for the Field Series brochure. * RJ Field Bayonet and other Field Series products are available through Amphenol PCD. These include RJF TV within MIL-DTL-38999 Series III threaded coupling connectors, and RJF 544 within ECTA push-pull plastic shell coupling. RJ Field Bayonet Cylindricals 50