HS-2604

HS-2604 EDEN Embedded Engine Board •Half Size•All-in-One•CRT/Panel•133MHz FSB• •ATA/33/66/100•Three LAN•RS-232/422/485• •4COM•PC/104•IrDA•USB•DOC• •WDT•H/W Monitor•Single +5V• •Industrial Embedded Single Board computer• Copyright Disclaimers The accuracy of contents in this manual has passed thorough checking and review before publishing. BOSER Technology Co., Ltd., the manufacturer and publisher, is not liable for any infringements of patents or other rights resulting from its use. The manufacturer will not be responsible for any direct, indirect, special, incidental or consequential damages arising from the use of this product or documentation, even if advised of the possibility of such damage(s). This manual is copyrighted and BOSER Technology Co., Ltd. reserves all documentation rights. Unauthorized reproduction, transmission, translation, and storage of any form and means (i.e., electronic, mechanical, photocopying, recording) of this document, in whole or partly, is prohibited, unless granted permission by BOSER Technology Co., Ltd. BOSER Technology Co., Ltd. reserves the right to change or improve the contents of this document without due notice. BOSER Technology Co., Ltd. assumes no responsibility for any errors or omissions that may appear in this manual, nor does it make any commitment to update the information contained herein. Trademarks Trademarks BOSER is a registered trademark of BOSER Technology Co., Ltd. ISB is a registered trademark of BOSER Technology Co., Ltd. VIA is a registered trademark of VIA Technologies, Inc. AMI is a registered trademark of AMI Software, Inc. All other trademarks, products and or product names mentioned herein are mentioned for identification purposes only, and may be trademarks and/or registered trademarks of their respective companies or owners. © Copyright 2004 BOSER Technology Co., Ltd. All Rights Reserved. Edition 1.3, October 04, 2004 Table of Contents Chapter 1 General Description ..................................1 1.1 Major Features ....................................................................... 2 1.2 Specifications ........................................................................ 3 1.3 Board Dimensions................................................................. 4 Chapter 2 Chapter 3 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 3.10 3.11 3.12 3.13 3.14 3.15 3.16 3.17 3.18 3.19 3.20 3.21 3.22 Unpacking ..................................................5 Hardware Installation ..............................7 2.1 Opening the Delivery Package............................................. 5 2.2 Inspection............................................................................... 5 Before Installation ................................................................. 7 Board Layout ......................................................................... 8 Jumper List ............................................................................ 9 Connector List ....................................................................... 9 Configuring the CPU ........................................................... 10 System Memory ................................................................... 10 DiskOnChip Address Setting .......................................... 10 VGA Controller .................................................................... 12 PCI E-IDE Drive Connector................................................. 14 Floppy Disk Drive Connector ............................................. 15 Serial Port Connectors ....................................................... 16 Parallel Connector............................................................... 18 Ethernet Connector............................................................. 19 IrDA Connector.................................................................... 20 USB Connector.................................................................... 20 CMOS Data Clear................................................................. 20 Power and Fan Connectors................................................ 21 Keyboard/Mouse Connectors ............................................ 21 System Front Panel Connectors........................................ 22 Watchdog Timer .................................................................. 23 Mini PCI Connector ............................................................. 25 PC/104 Connectors ............................................................. 27 Chapter 4 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 4.10 4.11 4.12 4.13 4.14 4.15 4.16 AMI BIOS Setup ..................................... 29 Starting Setup...................................................................... 29 Using Setup ......................................................................... 30 Main Menu............................................................................ 31 Standard CMOS Setup ........................................................ 32 Advanced CMOS Setup ...................................................... 33 Advanced Chipset Setup.................................................... 34 Power Management Setup ................................................. 35 PCI / Plug and Play Setup................................................... 36 Peripheral Setup.................................................................. 37 Hardware Monitor Setup..................................................... 38 Auto-Detect Hard Disks ...................................................... 38 Change Supervisor/User Password .................................. 39 Auto Configuration with Optimal Settings ....................... 40 Auto Configuration with Fail Safe Settings ...................... 41 Save Settings and Exit........................................................ 42 Exit Without Saving............................................................. 43 Chapter 5 Software Utilities..................................... 45 5.1 IDE Driver Installation ......................................................... 45 5.2 VGA Driver Installation ....................................................... 50 5.3 LAN Driver Installation........................................................ 56 Safety Instructions Integrated circuits on computer boards are sensitive to static electricity. To avoid damaging chips from electrostatic discharge, observe the following precautions: Do not remove boards or integrated circuits from their anti-static packaging until you are ready to install them. Before handling a board or integrated circuit, touch an unpainted portion of the system unit chassis for a few seconds. This helps to discharge any static electricity on your body. Wear a wrist-grounding strap, available from most electronic component stores, when handling boards and components. Fasten the ALLIGATOR clip of the strap to the end of the shielded wire lead from a grounded object. Please wear and connect the strap before handle the HS-2604 to ensure harmlessly discharge any static electricity through the strap. Please use an anti-static pad when putting down any components or parts or tools outside the computer. You may also use an anti-static bag instead of the pad. Please inquire from your local supplier for additional assistance in finding the necessary anti-static gadgets. NOTE: DO NOT TOUCH THE BOARD OR ANY OTHER SENSITIVE COMPONENTS WITHOUT ALL NECESSARY ANTI-STATIC PROTECTION. Chapter 1 General Description The HS-2604 is a 100/133MHz FSB VIA VT8606 chipset-based board designed for Mini PCI Local Bus VIA C3 EDEN 400/667MHz Embedded CPU. These features combine and make the HS-2604 an ideal all-in-one industrial single board computer. Additional features include an enhanced I/O with CRT/Panel, three LAN, and 4COM ports interfaces. Its onboard ATA/33/66/100 to IDE drive interface architecture allows the HS-2604 to support data transfers of 33, 66 or 100MB/sec. to one IDE drive connection. Designed with the VIA VT8606 core logic chipset, the board supports VIA C3 EDEN 400/667MHz Embedded CPU. The VIA VT8606 integrated S3 3D supporting CRT/Panel displays up to 1920 x 1440. System memory is also sufficient with the one SO-DIMM socket that can support up to 256MB. Additional onboard connectors include an advanced USB and IrDA ports providing faster data transmission, a DOS-compatible DiskOnChip socket with a maximum capacity of 288MB. And two external RJ-45 connectors and one 10-pin header for 10/100 Based Ethernet use. 1 To ensure the reliability in an unmanned or standalone system, the Watchdog Timer (WDT) onboard HS-2604 is designed with pure hardware that does not need the arithmetical functions of a real-time clock chip. If any program causes unexpected halts to the system, the onboard Watchdog Timer (WDT) will automatically reset the CPU or generate an interrupt to resolve such condition. 1.1 Major Features The HS-2604 comes with the following features: VIA C3 EDEN 400/667MHz Embedded CPU VIA VT8606/VT82C686B system chipset Supports 100/133MHz FSB One SO-DIMM socket with a max. capacity of 256MB SMC 37C669, VIA VT82C686B super I/O chipset Fast PCI ATA/33/66/100 IDE controller Three RS-232 and one RS-232/422/485 serial ports PC/104 Bus connector VIA VT8606 CRT/Panel display controller Three RealTek RTL8100 10/100 Based LAN DiskOnChip socket supporting memory size of up to 288MB Two USB connectors Supports Hardware Monitor function Supports Single +5V power in 2 1.2 Specifications CPU: VIA C3 EDEN 400/667MHz embedded CPU Bus Interface: Mini PCI Local Bus Memory: One SO-DIMM socket supporting up to 256MB Chipset: VIA VT8606/VT82C686B I/O Chipset: SMC 37C669, VIA VT82C686B VGA: VIA VT8606 integrated S3 3D supporting CRT/Panel displays up to 1920 x 1440 IDE: Two IDE disk drives supporting ATA/33/66/100 and with transfer rates of up to 33/66/100MB/sec. FDD: Supports up to two floppy disk drives Parallel: One enhanced bi-directional parallel port supporting SPP/ECP/EPP LAN: Three RealTek RTL8100 10/100 Based LAN Serial Port: 16C550 UART-compatible RS-232/422/485 x 1 and RS-232 x 3 serial ports with 16-byte FIFO PC/104: PC/104 connector for 16-bit ISA Bus IrDA: One IrDA TX/RX header USB: Two USB connectors Keyboard/Mouse: PS/2 6-pin Mini DIN or 6-pin connector DiskOnChip: DiskOnChip socket supporting memory sizes of up to 288MB BIOS: AMI PnP Flash BIOS Watchdog Timer: Sets 1, 2, 10, 20, 110, 220 seconds, activity trigger with Reset or NMI CMOS: Battery backup Power: Single +5V/3.2A power in Operating Temperature: -20 ~ +60°C (EDEN 400MHz) Hardware Monitor: VIA VT82C686B Board Size: 14.5 x 10.2 cm 3 1.3 Board Dimensions 4 Chapter 2 Unpacking 2.1 Opening the Delivery Package The HS-2604 is packed in an anti-static bag. The board has components that are easily damaged by static electricity. Do not remove the anti-static wrapping until proper precautions have been taken. Safety Instructions in front of this manual describe anti-static precautions and procedures. 2.2 Inspection After unpacking the board, place it on a raised surface and carefully inspect the board for any damage that might have occurred during shipment. Ground the board and exercise extreme care to prevent damage to the board from static electricity. Integrated circuits will sometimes come out of their sockets during shipment. Examine all integrated circuits, particularly the BIOS, processor, memory modules, ROM-Disk, and keyboard controller chip to ensure that they are firmly seated. The HS-2604 delivery package contains the following items: HS-2604 Board x 1 Utility CD Disk x 1 IDE flat cable x 1 FDD flat cable x 1 Printer cable x 1 10-pin VGA cable x 1 One PS/2 KB/MS Transfer cable x 1 One Ethernet cable x 1 One RS-232 COM Port cable x 4 8-pin USB split type cable x 1 2-pin Power cable x 1 Jumper Bag x 1 User’s Manual 5 It is recommended that you keep all the parts of the delivery package intact and store them in a safe/dry place for any unforeseen event requiring the return shipment of the product. In case you discover any missing and/or damaged items from the list of items, please contact your dealer immediately. 6 Chapter 3 Hardware Installation This chapter provides the information on how to install the hardware using the HS-2604. This chapter also contains information related to jumper settings of switch, watchdog timer, and the DiskOnChip address selection etc. 3.1 Before Installation After confirming your package contents, you are now ready to install your hardware. The following are important reminders and steps to take before you begin with your installation process. 1. Make sure that all jumper settings match their default settings and CMOS setup correctly. Refer to the sections on this chapter for the default settings of each jumper. Go through the connections of all external devices and make sure that they are installed properly and configured correctly within the CMOS setup. Refer to the sections on this chapter for the detailed information on the connectors. Keep the manual and diskette in good condition for future reference and use. 2. 3. 7 3.2 Board Layout 8 3.3 Jumper List Default Setting Setting Page 23 20 10 23 16 16 12 Jumper JP1 WDT Active Type Setting: Disabled Open JP2 Clear CMOS: Normal Operation Short 1-2 JP4(1-4) DOC Address Select: D000 Short 1-2, 3-4 Short 5-6, 7-8, JP4(5-10) WDT Timer Select: 1sec. 9-10 RS-422/485 Receiver JP5 Open Enabled/Disabled Select: Disabled COM2 Use RS-232 or RS-422/485: Open JP6 RS-232 JP7 Panel Voltage: +3.3V Short 1-2 3.4 Connector List Definition 5-pin ATX Power In Connector PC/104 40-pin Connector PC/104 64-pin Connector 2-pin Power In Connector Floppy Connector RS-422/485 Connector (5x2 header) Dual RJ-45 Connector Parallel Connector PS/2 6-pin Mini DIN KB/MS Connector 6-pin KB/MS Connector COM 3 Connector (5x2 header) COM 1 Connector (DB9) COM 1 Connector (5x2 header) COM 2 Connector (5x2 header) COM 4 Connector (5x2 header) USB Connector IrDA Connector 50-pin Panel Connector CRT Connector (5x2 header) LVDS Connector IDE Connector LAN Connector (5x2 header) SO-DIMM Socket Connector CN1 CN2 CN3 CN4 CN6 CN7 CN8 CN9 CN10 CN11 CN12 CN13 CN14 CN15 CN16 CN17 CN19 CN20 CN21 CN22 CN23 CN24 DM1 Page 21 27 27 21 15 16 19 18 21 21 16 16 16 16 16 20 20 12 12 12 14 19 10 . . . More on next page . . . 9 Connector FN1 JP3 PC1 U1 Definition Fan Connector Front Panel Connector Mini PCI Connector TM DiskOnChip Socket Page 21 22 25 10 3.5 Configuring the CPU The HS-2604 embedded with a VIA C3 EDEN 400/667MHz CPU. User don’t need to adjust the frequently and check speed of VIA C3 EDEN CPU. 3.6 System Memory DiskOnChip Address Setting The HS-2604 provides one SO-DIMM socket at locations DM1. The maximum capacity of the onboard memory is 256MB. 3.7 The DiskOnChip function allows the system to boot or operate without a FDD or a HDD. DiskOnChip modules may be formatted as drive C or A. With DiskOnChip, user may also execute DOS commands such as FORMAT, SYS, COPY, XCOPY, DISCOPY and DISKCOMP etc. The U1 location onboard the HS-2604 is the DiskOnChip module socket. Jumper JP4(1-4) assigns the starting memory address of the installed module. If you have another memory device that has a similar memory capacity with that of the DOC in your system, please set both at different memory address mapping to avoid the mapping area conflicts. Failing to do so will not make the HS-2604 and the additional memory device function properly. JP4(1-4): DiskOnChip Address Select Address D000 D800 E000 PINS 1-2 Short Open Short PINS 3-4 Short Short Open 10 3.7.1 Installing DiskOnChip Modules When installing a DiskOnChip module onto your board, please take note of the following: 1. Orient yourself properly with the location of the DiskOnChip socket. Try to locate the pin 1 location on your socket. Pin numbers are usually printed on either the component side or the solder side of your board. 2. Locate the Pin 1 location on your DiskOnChip module. More often than not, Pin 1 can be found on the lower right corner of the chip. Please refer to the diagram for the exact location. 3. Once you have figured out where the pin 1 locations are on both chip and socket, align the module’s pins on an upright angle against the socket. Using both thumbs, gently press the module into the socket until all the pins are secured to their designations. Disk OnC hip Pin 1 Location 4. The installation is now complete and your module is now ready for use. NOTE: If you encounter difficulty installing your DiskOnChip module, please consult a qualified technician or engineer to perform the installation. 3.7.2 Removing DiskOnChip Modules When removing a DiskOnChip module from its socket, please take note of the following: 1. Loosen the contact of the module from its socket using a screwdriver. 11 2. Insert the screwdriver’s flat head into a gap on either end of the socket. Do not insert the screwdriver head on either side where the pins are located. Doing so might damage the pins in the process. 3. Slowly lift the screwdriver handle upwards. This will disengage the module from its socket. NOTE: If you encounter difficulty removing your DiskOnChip module, please consult a qualified technician or engineer to remove it for you. 3.8 VGA Controller The HS-2604 provides three connection methods of a VGA device. CN21 offers a single standard CRT connector (5x2 header) while CN20 is the 50-pin panel connector and CN22 is the LVDS interface connector onboard reserved for flat panel installation. CN21: CRT Connector (5x2 header) PIN Description PIN Description 1 3 5 7 9 Red Green Blue HSYNC VSYNC 2 4 6 8 10 GND GND GND SDA SCL Red 1 Green 3 Blue HSYNC VSYNC 5 7 9 2 GND 4 GND 6 GND 8 SDA 10 SCL CN22: LVDS Interface Connector PIN Description PIN Description 1 3 5 7 9 11 VCC3 Y0 Y2 Y4 Y6 GND 2 4 6 8 10 12 VCC3 Y1 Y3 Y5 Y7 GND VCC3 Y0 Y2 Y4 Y6 GND 11 12 1 2 VCC3 Y1 Y3 Y5 Y7 GND NOTE: LVDS cable should be produced very carefully. Y1 & Y2 have to be fabricated in twister pair (Y2 & Y3, Y4 & Y5, Y6 & Y7 and so on) otherwise the signal won’t be stable. Please set the proper voltage of your panel using JP7 before proceeding on installing it. 12 CN20: 50-pin Panel Connector PIN. Description PIN Description 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 N/C GND Note 3.3V / 5V ENAVEE PD0 PD2 PD4 PD6 PD8 PD10 PD12 PD14 PD16 PD18 PD20 PD22 PD24 SHFCLK DE GND P26 P28 P30 P32 P34 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 N/C GND ENAVDD GND PD1 PD3 PD5 PD7 PD9 PD11 PD13 PD15 PD17 PD19 PD21 PD23 PD25 FLM LP ENABKL P27 P29 P31 P33 P35 N/C GND 3.3V/5V ENAVEE PD0 PD2 PD4 PD6 PD8 PD10 PD12 PD14 PD16 PD18 PD20 PD22 PD24 SHFCLK DE GND P26 P28 P30 P32 P34 49 50 1 2 N/C GND ENAVDD GND PD1 PD3 PD5 PD7 PD9 PD11 PD13 PD15 PD17 PD19 PD21 PD23 PD25 FLM LP ENABKL P27 P29 P31 P33 P35 NOTE: Please set the proper voltage of your panel using JP7 before proceeding on installing it. The HS-2604 has an onboard jumper that selects the working voltage of the flat panel connected to the system. Jumper JP7 offers two voltage settings for the user. JP7: Panel Voltage Select Options 3.3 V 5V Settings Short 1-2 Short 2-3 1 GND +3.3V VCC 3 13 3.9 PCI E-IDE Drive Connector CN23 is a standard 44-pin 2.0mm pitch connector daisy-chain driver connector serves the PCI E-IDE drive provisions onboard the HS-2604. A maximum of two ATA/33/66/100 IDE drives can connect to the HS-2604 via CN23. CN23: IDE Connector PIN 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 PDD8 PDD9 GND Description Reset DATA 7 DATA 6 DATA 5 DATA 4 DATA 3 DATA 2 DATA 1 DATA 0 GND PDREQ IOW# IOR# PIORDY RPDACKInterrupt RPDA1RPDA0RPCS1HDD Active LED VCC GND PDD10 PDD11 PDD12 PDD13 PDD14 PDD15 GND ’ PIN 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 Description GND DATA 8 DATA 9 DATA 10 DATA 11 DATA 12 DATA 13 DATA 14 DATA 15 N/C GND GND GND PR1PD1GND N/C PATA66 RPDA2RPCS3GND VCC N/C -PDCS3 PDA2 PD33 GND GND GND GND GND VCC VCC N/C N/C 2 1 PIORDY -PDDACK HDD ACTIVE GND -PDIOW -PDIOR PDDREQ IRQ14 PDD7 PDD6 PDD5 PDD4 PDD3 PDD2 PDD1 PDD0 -IDERST -PDCS1 PDA1 PDA0 GND N/C 44 43 14 3.10 Floppy Disk Drive Connector The HS-2604 uses a standard 34-pin header connector, CN6, for floppy disk drive connection. A total of two FDD drives may be connected to CN6 at any given time. CN6: FDD Connector PIN 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 Description GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND PIN 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 Description DRVDEN0 N/C DRVDEN1 INDEX# MTR0# DS1# DS0# MTR1# DIR# STEP# WDATA# WGATE# TRAK00# WRTPRT# RDATA# HDSEL# DSKCHG# DSKCHG# 34 33 GND WRTPRT# GND DRVDEN0 DRVDEN1 TRAK00# WGATE# WDATA# ’ RDATA# GND u 2 1 GND GND GND GND GND GND GND GND GND GND GND GND GND GND HDSEL# INDEX# MTR0# MTR1# STEP# DS1# DS0# DIR# N/C 15 3.11 Serial Port Connectors The HS-2604 offers two NS16C550 compatible UARTs with Read/Receive 16-byte FIFO serial ports and four internal 10-pin headers and one RS-422/485 connector. CN14: COM1 Connector (5x2 Header) PIN Description PIN Description 1 3 5 7 9 DCD1 RXD1 TXD1 DTR1 GND 2 4 6 8 10 DSR1 RTS1 CTS1 RI1 N/C DCD1 1 RXD1 3 TXD1 DTR1 GND 5 7 9 2 DSR1 4 RTS1 6 CTS1 8 RI1 10 N/C CN15: COM2 Connector (5x2 Header) PIN Description PIN Description 1 3 5 7 9 DCD2 RXD2 TXD2 DTR2 GND 2 4 6 8 10 DSR2 RTS2 CTS2 RI2 N/C DCD2 1 RXD2 3 TXD2 DTR2 GND 5 7 9 2 DSR2 4 RTS2 6 CTS2 8 RI2 10 N/C CN12: COM3 Connector (5x2 Header) PIN Description PIN Description 1 3 5 7 9 DCD3 RXD3 TXD3 DTR3 GND 2 4 6 8 10 DSR3 RTS3 CTS3 RI3 N/C DCD3 1 RXD3 3 TXD3 DTR3 GND 5 7 9 2 DSR3 4 RTS3 6 CTS3 8 RI3 10 N/C 16 CN16: COM4 Connector (5x2 Header) PIN Description PIN Description 1 3 5 7 9 DCD4 RXD4 TXD4 DTR4 GND 2 4 6 8 10 DSR4 RTS4 CTS4 RI4 N/C DCD4 1 RXD4 3 TXD4 DTR4 GND 5 7 9 2 DSR4 4 RTS4 6 CTS4 8 RI4 10 N/C CN7: RS-422/485 Connector (5x2 Header, COM2) PIN Description PIN Description 1 3 5 7 9 TXRX+ GND RTS+ CTS2 4 6 8 10 TX+ RXRTSCTS+ N/C TX- 1 RX+ 3 GND RTS+ CTS5 7 9 2 TX+ 4 RX6 RTS8 CTS+ 10 N/C NOTE: The terminal resistance of RX & TX is set in 180Ω. Options Always Enable Enable by “-RTS“ Signal Always Disabled JP5: RS-422/485 Receiver Enabled/Disabled Select Settings Short 1-2 Short 3-4 Open 3 4 1 2 JP6: COM2 use RS-232 or RS-422/485 Select Options RS-232 RS-422/485 Settings Open Short 1 2 NOTE: RS-422/485 port use COM2. RS-232 of COM2 cannot be used while RS-422/485 enable. 17 CN13: COM1 Connector (DB9) PIN Description PIN 1 2 3 4 5 DCD1 RXD1 TXD1 DTR1 GND 6 7 8 9 Descriptio n DSR1 RTS1 CTS1 RI1 GND DRT1 TXD1 RXD1 DCD1 5 9 RI1 CTS1 RTS1 DSR1 1 6 3.12 Parallel Connector CN9 is a standard 26-pin flat cable connector deigned to accommodate parallel port connection onboard the HS-2604. CN9: Parallel Connector PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 Description Strobe DATA 0 DATA 1 DATA 2 DATA 3 DATA 4 DATA 5 DATA 6 DATA 7 Acknowledge Busy Paper Empty Printer Select Printer Select LN# Auto Form Feed PIN 14 15 16 17 18 19 20 21 22 23 24 25 26 Description Auto Form Feed ERROR# Initialize Printer Select LN# GND GND GND GND GND GND GND GND GND ERROR# Initialize GND GND GND GND GND GND GND GND Paper Empty GND 26 13 Printer Select 14 1 DATA0 DATA1 DATA2 DATA3 DATA4 DATA5 DATA6 DATA7 Strobe Acknowledge Busy 18 3.13 Ethernet Connector The HS-2604 provides one external dual RJ-45 interface connector. Please refer to the following for its pin information. And one 10-pin internal connector at CN24. CN8: Dual RJ-45 Connector PIN Description PIN Description 1 2 3 4 5 6 7 8 1RX+ 1TX+ 1TX+ 1TX1RX+ R/C GND R/C GND 1RXR/C GND R/C GND R/C GND R/C GND 9 10 11 12 13 14 15 16 2RX+ 2TX+ 2TX+ 2TX2RX+ R/C GND R/C GND 2RXR/C GND R/C GND R/C GND R/C GND 15 16 2RXVDD3 1 3RX+ 3 Link LED RX LED 3TX+ 5 7 9 1 2 7 8 9 10 R/C GND R/C GND 1TX- 1RX- 2TX- CN24: LAN Connector (5x2 Header) PIN Description PIN Description 1 3 5 7 9 VDD3 3RX+ Link LED RX LED 3TX+ 2 4 6 8 10 TX LED 3RXR/C GND R/C GND 3TX2 TX LED 4 3RX6 R/C GND 8 R/C GND 10 3TX- NOTE: CN24 is the 3rd LAN connector. R/C GND R/C GND 19 3.14 IrDA Connector CN19 is a 5-pin internal IR communication connector for connection of an IrDA device. CN19: IrDA Connector PIN 1 2 3 4 5 Description VCC N/C IRRX GND IRTX 1 2 3 4 5 GND 3.15 USB Connector The HS-2604 provides one 8-pin connectors, at locations CN17, for two USB connections to the HS-2604. CN17: USB Connector USBD0+ USBD0- 1 3 5 7 VCC USBD1USBD1+ GND 2 4 6 8 VCC USBD0USBD0+ GND 2 1 USBD1USBD1+ GND VCC GND 8 7 3.16 CMOS Data Clear The HS-2604 has a Clear CMOS jumper on JP2. JP2: Clear CMOS Options Normal Operation Clear CMOS Settings Short 1-2 Short 2-3 1 VCC3 VBAT GND VCC PIN Description PIN Description IRRX IRTX VCC N/C 3 IMPORTANT: Before you turn on the power of your system, please set JP2 to Short 1-2 for normal operation. 20 3.17 Power and Fan Connectors HS-2604 provides one 5-pin power connectors at CN1. And one 2-pin power in at CN4. CN1: 5-pin ATX Power In Connector PS_ON GND 5VSB +12V 1 3 5 GND +12V VCC 2 4 PS_ON 5VSB 1 VCC 5 PIN Description PIN Description CN4: 2-pin Power In Connector PIN Description 1 2 VCC GND 1 VCC GND 2 FN1: Fan Connector PIN 1 2 3 Description Fan Speed +5V GND 3 GND +5V Fan Speed 1 Connector FN1 onboard HS-2604 is a 3-pin fan power output connector. And HS-2604 supports +5V Fan only. 3.18 Keyboard/Mouse Connectors The HS-2604 offers two possibilities for keyboard/mouse connections. The connections are via CN10 for an external PS/2 type keyboard or via CN11 for an internal 6-pin cable converter to an AT keyboard. 21 CN10: PS/2 6-pin Mini DIN Keyboard Connector PIN 1 2 3 4 5 6 Description Keyboard Data Mouse Data GND +5V Keyboard Clock Mouse Clock Keyboard Clock 5 3 GND 1 Data Keyboard Mouse Clock 6 2 Mouse Data 4 +5V CN11: 6-pin Keyboard Connector PIN 1 2 3 4 5 6 Description Keyboard Clock Keyboard Data Mouse Data GND +5V Mouse Clock 1 2 3 4 5 6 Keyboard Clock Keyboard Data 3.19 System Front Panel Connectors The HS-2604 has one LED at location JP3 that indicates the power-on status. This visual feature of the IDE LED may also be connected to an external IDE LED, Speaker, Reset Switch, Power LED, EXT SMI, Power Button, and SLP Button via connector JP3(13-15), JP3(1-3-5-7), JP3(9-11), JP3(2-4), JP3(6-8), JP3(10-12), JP3(14-16). JP3: System Front Panel Connector PIN Description 1 3 5 7 9 11 13 15 +5V GND N/C Speaker GND Reset 330Ω Pull +5V HDD LED PIN 2 4 6 8 10 12 14 16 Description 330Ω Pull +5V GND EXT SMI GND PW Bottom GND SLP Bottom GND 22 Mouse Clock Mouse Data GND +5V Connector JP3 Orientation 1 SPEAKER 3 5 7 RST_SW HD_LED 9 11 2 4 6 8 10 12 PWR LED EXT_SMI PWR button SLP button 13 14 15 16 3.20 Watchdog Timer There are three access cycles of Watch-Dog Timer as Enable, Refresh and Disable are the three access cycles of Watchdog Timer. The Enable cycle proceeds via READ PORT 443H whereas the Disable cycle proceeds via READ PORT 045H. A continued Enable cycle after a first Enable cycle means Refresh. Once the Enable cycle is active, a Refresh cycle is requested before the time-out period. This restarts counting of the WDT period. When the time counting goes over the period preset of WDT, it will assume that the program operation is abnormal. A System Reset signal to re-start or a NMI cycle to the CPU transpires when such error happens. Jumper JP1 is used to select the function of Watchdog Timer. JP1: Watchdog Timer Active Type Setting Options Active NMI System Reset Disabled Watchdog Timer Settings Short 1-2 Short 2-3 Open 1 3 JP4(5-10): WDT Timeout Period Select Period 1 sec 2 sec 10 sec 20 sec 110 sec 220 sec PINS 5-6 Short Open Short Open Short Open PINS 7-8 PINS 9-10 Short Short Open Open Short Short Short Short Short Short Open Open 23 The Watchdog Timer is disabled after the system Power-On. It can be enabled via an Enable cycle and reading the control port (443H), or via a Refresh cycle and reading the control port (443H), or via a Disable cycle and reading the disable control port (045H). After an Enable cycle of WDT, user must immediately execute a Refresh cycle to WDT before its period setting comes to an end every 1, 2, 10, 20, 110 or 220 seconds. If the Refresh cycle does not activate before WDT period cycle, the onboard WDT architecture will issue a Reset or NMI cycle to the system. There are three I/O ports that control the Watchdog Timer. 443H 443H 045H I/O Read I/O Read I/O Read The Enable cycle The Refresh cycle The Disable cycle The following sample program shows how to Enable, Disable and Refresh the Watchdog Timer: WDT_EN_RF WDT_DIS WT_Enable EQU EQU PUSH PUSH MOV IN POP POP RET PUSH PUSH MOV IN POP POP RET PUSH PUSH MOV IN POP POP RET 0443H 0045H AX DX DX,WDT_EN_RF AL,DX DX AX AX DX DX,WDT_ET_RF AL,DX DX AX AX DX DX,WDT_DIS AL,DX DX AX ; keep AX DX ; enable the WDT ; get back AX, DX WT_Refresh ; keep AX, DX ; refresh the WDT ; get back AX, DX WT_DISABLE ; disable the WDT ; get back AX, DX 24 3.21 Mini PCI Connector HS-2604 supports a Mini PCI connector. The peripheral component with standard Type1 Mini PCI can be used. For particular requirement, please refer to “BOSER Mini PCI series product” on website or contact with us. PC1: Mini PCI Connector Pin Information PIN 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 53 55 57 59 61 Description INTB# 3.3V INTA# GND CLK GND REQ# 3.3V AD[31] AD[29] GND AD[27] AD[25] REQ1 C/BE[3]# AD[23] GND AD[21] AD[19] GND AD[17] C/BE[2]# IRDY# 3.3V N/C SERR# GND PERR# C/BE[1]# AD[14] GND PIN 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 62 Description 5V INTD# INTC# N/C RST# 3.3V GNT# GND PME# GNT1 AD[30] 3.3V AD[28] AD[26] AD[24] AD[21] GND AD[22] AD[20] PAR AD[18] AD[16] GND FRAME# TRDY# STOP# 3.3V DEVSEL# GND AD[15] AD[13] . . . More on next page . . . 25 PIN 63 65 67 69 71 73 75 77 79 81 83 85 87 89 91 93 95 97 99 Description AD[12] AD[10] GND AD[8] AD[7] 3.3V AD[5] REQ2 AD[3] 5V AD[1] GND AC_SYNC AC_SDATA_IN AC_BIT_CLK AC_CODEC_ID1# MOD_AUDIO_MON AUDIO_GND SYS_AUDIO_OUT PIN 64 66 68 70 72 74 76 78 80 82 84 86 88 90 92 94 96 98 100 Description AD[11] GND AD[9] C/BE[0]# 3.3V AD[6] AD[4] AD[2] AD[0] GNT2 GNT3 GND M66EN AC_SDATA_OUT AC_CODEC_IDO# AC_RESET# REQ3 GND SYS_AUDIO_IN 2 100 1 Mini PCI Socket pin orientation 99 26 3.22 PC/104 Connectors The PC/104 expansion bus offers provisions to connect all types of PC/104 modules. With the PC/104 bus being known as the new generation of industrial embedded 16-bit PC standard bus, thousands of PC/104 modules from multiple venders can be easily installed onboard. The detailed pin assignment of the PC/104 expansion bus connectors CN2 and CN3 are listed on the following tables: NOTE： The PC/104 connector allows direct plugging or stack-through piling of PC/104 modules without requiring the PC/104 mounting kit. CN2: PC/104 40-pin Connector PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Description PIN Description GND -MEMCS16 -IOSC16 IRQ10 IRQ11 IRQ12 IRQ15 IRQ14 -DACK0 DRQ0 -DACK5 DRQ5 -DACK6 DRQ6 -DACK7 DRQ7 +5V -MASTER GND GND 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 GND -SBHE LA23 LA22 LA21 LA20 LA19 LA18 LA17 -MEMR -MEMW SD8 SD9 SD10 SD11 SD12 SD13 SD14 SD15 N/C Connector diagram rotated 90 degrees clockwise from original position 1 21 20 40 27 CN3: PC/104 64-pin Connector PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 Description PIN Description -IOCHECK SD7 SD6 SD5 SD4 SD3 SD2 SD1 SD0 IOCHRDY AEN SA19 SA18 SA17 SA16 SA15 SA14 SA13 SA12 SA11 SA10 SA9 SA8 SA7 SA6 SA5 SA4 SA3 SA2 SA1 SA0 GND 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 GND RESETDRV +5V IRQ9 -5V N/C -12V N/C +12V GND -SMEMW -SMEMR -IOW -IOR -DACK3 DRQ3 -DACK1 DRQ1 -REFRESH SYSCLK IRQ7 IRQ6 IRQ5 IRQ4 IRQ3 -DACK2* TC BALE +5V OSC N/C GND Connector diagram rotated 90 degrees clockwise from original position 1 33 32 64 28 Chapter 4 AMI BIOS Setup The HS-2604 uses AMI BIOS for the system configuration. The AMI BIOS setup program is designed to provide the maximum flexibility in configuring the system by offering various options that could be selected for end-user requirements. This chapter is written to assist you in the proper usage of these features. 4.1 Starting Setup The AMI BIOS is immediately activated when you first power on the computer. The BIOS reads the system information contained in the CMOS and begins the process of checking out the system and configuring it. When it finishes, the BIOS will seek an operating system on one of the disks and then launch and turn control over to the operating system. While the BIOS is in control, the Setup program can be activated in one of two ways: 1. By pressing immediately after switching the system on, or 2. By pressing the key when the following message appears briefly at the bottom of the screen during the POST (Power On Self Test). Press DEL to enter SETUP. If the message disappears before you respond and you still wish to enter Setup, restart the system to try again by turning it OFF then ON or pressing the "RESET" button on the system case. You may also restart by simultaneously pressing , , and keys. If you do not press the keys at the correct time and the system does not boot, an error message will be displayed and you will again be asked to... PRESS F1 TO CONTINUE, DEL TO ENTER SETUP 29 4.2 Using Setup In general, you use the arrow keys to highlight items, press to select, use the and keys to change entries, press for help and press to quit. The following table provides more detail about how to navigate in the Setup program using the keyboard. Up arrow Down arrow Left arrow Right arrow Esc key Move to previous item Move to next item Move to the item in the left hand Move to the item in the right hand Main Menu -- Quit and not save changes into CMOS Status Page Setup Menu and Option Page Setup Menu -Exit current page and return to Main Menu Increase the numeric value or make changes Decrease the numeric value or make changes Increase the numeric value or make changes Decrease the numeric value or make changes General help, only for Status Page Setup Menu and Option Page Setup Menu Change color from total 16 colors. F2 to select color forward, (Shift) F2 to select color backward Calendar, only for Status Page Setup Menu Reserved Restore the previous CMOS value from CMOS, only for Option Page Setup Menu Load the default CMOS value from BIOS default table, only for Option Page Setup Menu Load the default Reserved Reserved Save all the CMOS changes, only for Main Menu PgUp key PgDn key + key - key F1 key (Shift)F2 key F3 key F4 key F5 key F6 key F7 key F8 key F9 key F10 key 4.2.1 Getting Help Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for the highlighted item. To exit the Help Window press or the F1 key again. 30 4.3 Main Menu Once you enter the AMI BIOS CMOS Setup Utility, the Main Menu will appear on the screen. The Main Menu allows you to select from several setup functions and two exit choices. Use the arrow keys to select among the items and press to enter the sub-menu. AMIBIOS HIFLEX SETUP UTILITY – VERSION x.xx (C)2001 American Megatrends, Inc. All Rights Reserved Standard CMOS Setup Advanced CMOS Setup Advanced Chipset Setup Power Management Setup PCI / Plug and Play Setup Peripheral Setup Hardware Monitor Setup Auto-Detect Hard Disks Change User Password Change Supervisor Password Auto Configuration with Optimal Settings Auto Configuration with Fail Safe Settings Save Settings and Exit Exit Without Saving Standard CMOS setup for changing time, date, hard disk type, etc. ESC:Exit :Sel F2/F3: Color F10: Save & Exit NOTE: A brief description of the highlighted choice appears at the bottom of the screen. 31 4.4 Standard CMOS Setup The Standard Setup is used for the basic hardware system configuration. The main function is for Data/Time and Floppy/Hard Disk Drive settings. Please refer to the following screen for the setup. When the IDE hard disk drive you are using is larger than 528MB, you must set the HDD mode to LBA mode. Please use the IDE Setup Utility in BIOS SETUP to install the HDD correctly. AMIBIOS SETUP – STANDARD CMOS SETUP (C)2001 American Megatrends, Inc. All Rights Reserved Date (mm/dd/yyyy) : Thu Jan 03, 2002 Time (hh/mm/ss) : 19:04:12 Floppy Drive A: Floppy Drive B: 1.44MB, 3.5” Not Installed Size Cyln Head WPcom Sec LBA Blk PIO 32Bit Mode Mode Mode Mode Base Memory : 639 KB Extd Memory : 119 MB Type Pri Master : Auto Pri Slave : Auto Sec Master : Not Install Sec Slave : Not Install Boot Sector Virus Protection : Month: Jan - Dec Day: 01 - 30 Year: 1980 - 2099 Disabled ESC:Exit :Sel PgUp/PgDn: Modify F1:Help F2/F3:Color 32 4.5 Advanced CMOS Setup This section allows you to configure your system for the basic operation. You have the opportunity to select the system’s default speed, boot-up sequence, keyboard operation, shadowing and security. AMIBIOS SETUP – STANDARD CMOS SETUP (C)2001 American Megatrends, Inc. All Rights Reserved Quick Boot 1st Boot Device 2nd Boot Device 3rd Boot Device Try Other Boot Devices S.M.A.R.T. for Hard Disks BootUp Num-Lock Floppy Drive Swap Floppy Drive Seek PS/2 Mouse Support Primary Display Password Check Boot To OS/2 CPU MicroCode Updation CPU Serial Number L1 Cache L2 Cache System BIOS Cacheable C000,32k Shadow C800,16k Shadow CC00,16k Shadow D000,16k Shadow D400,16k Shadow D800,16k Shadow DC00,16k Shadow Enabled Floppy IDE-0 CD-ROM Yes Disabled On Disabled Disabled Enabled VGA/EGA Setup No Enabled Disabled Enabled Enabled Enabled Cache Disabled Disabled Disabled Disabled Disabled Disabled Available Options: Disabled Enabled ESC:Exit :Sel PgUp/PgDn: Modify F1:Help F2/F3:Color 33 4.6 Advanced Chipset Setup This section allows you to configure the system based on the specific features of the installed chipset. This chipset manages bus speeds and the access to the system memory resources, such as DRAM and the external cache. It also coordinates the communications between the conventional ISA and PCI buses. It must be stated that these items should never be altered. The default settings have been chosen because they provide the best operating conditions for your system. You might consider and make any changes only if you discover that the data has been lost while using your system. AMIBIOS SETUP – ADVANCED CHIPSET SETUP (C)2001 American Megatrends, Inc. All Rights Reserved ******** DRAM Timing ******** Configure SDRAM Timing by SPD DRAM Frequency SDRAM CAS# Latency DRAM Bank Interleave Memory Hole AGP Mode AGP Fast Write AGP Comp. Driving Manual AGP Comp. Driving AGP Aperture Size AGP Master 1 W/S Write AGP Master 1 W/S Read Search for MDA Resources PCI Delay Transaction ISA Bus Clock USB Controller USB Device Legacy Support Port 64/60 Emulation ATX Power Supply Enabled Auto 3 Enabled Disabled 4x Disabled Auto CB 64MB Disabled Disabled Yes Enabled PCI CLK/4 USB Port 0 & 1 Disabled Disabled Enabled Available Options: Disabled Enabled ESC:Exit :Sel PgUp/PgDn: Modify F1:Help F2/F3:Color 34 4.7 Power Management Setup The Power Management Setup allows user to configure the system for saving energy in a most effective way while operating in a manner consistent with his own style of computer use. AMIBIOS SETUP – POWER MANAGEMENT SETUP (C)2001 American Megatrends, Inc. All Rights Reserved ACPI Aware O/S ACPI Standby State USB Device Wakeup From S3-S5 Re-Call VGA BIOS at S3 Resuming Power Management / APM Video Power Down Mode Hard Disk Power Down Mode Standby Time Out (Minute) Suspend Time Out (Minute) Throttle Slow Clock Ratio Display Activity IRQ3 IRQ4 IRQ5 IRQ7 IRQ9 IRQ10 IRQ11 IRQ12 IRQ13 IRQ14 IRQ15 System Thermal Thermal Active Temperature Thermal Slow Clock Ratio Power Button Function Restore on AC / Power Loss Resume On Ring Resume On LAN Resume On PME# Resume On KBC Wake-Up Key Wake-Up Password Resume On PS/2 Mouse Resume On RTC Alarm RTC Alarm Date RTC Alarm Hour RTC Alarm Minute RTC Alarm Second No Auto Disabled Disabled Disabled Disabled Disabled Disabled Disabled 50%~56.25% Ignore Monitor Monitor Ignore Monitor Ignore Ignore Ignore Ignore Ignore Monitor Ignore Disabled 65°C / 149°F 50%~56.25% On / Off Last State Disabled Disabled Disabled Disabled N/A N/A Disabled Disabled 15 12 30 30 Available Options: No Yes ESC:Exit :Sel PgUp/PgDn: Modify F1:Help F2/F3:Color 35 4.8 PCI / Plug and Play Setup This section describes configuring the PCI bus system. PCI, or Personal Computer Interconnect, is a system that allows I/O devices to operate at speeds nearing the speed the CPU itself uses when communicating with its own special components. This section covers some very technical items and it is strongly recommended that only experienced users should make any changes to the default settings. AMIBIOS SETUP – PCI / PLUG AND PLAY SETUP (C)2001 American Megatrends, Inc. All Rights Reserved Plug and Play Aware O/S Clear NVRAM OnChip VGA Frame Buffer Size PCI Latency Timer (PCI Clocks) Primary Graphics Adapter Boot Screen Select LCD Panel Type DMA Channel 0 DMA Channel 1 DMA Channel 3 DMA Channel 5 DMA Channel 6 DMA Channel 7 IRQ3 IRQ4 IRQ5 IRQ7 IRQ9 IRQ10 IRQ11 IRQ14 IRQ15 No No 8MB 32 On Chip AGP Auto 640 x 480 PnP PnP PnP PnP PnP PnP PCI/PnP PCI/PnP PCI/PnP PCI/PnP PCI/PnP PCI/PnP PCI/PnP PCI/PnP PCI/PnP Available Options: No Yes ESC:Exit :Sel PgUp/PgDn: Modify F1:Help F2/F3:Color 36 4.9 Peripheral Setup The IDE hard drive controllers can support up to two separate hard drives. These drives have a master/slave relationship that is determined by the cabling configuration used to attach them to the controller. Your system supports two IDE controllers--a primary and a secondary--so you can install up to four separate hard disks. PIO means Programmed Input/Output. Rather than having the BIOS issue a series of commands to affect the transfer to or from the disk drive, PIO allows the BIOS to tell the controller what it wants and then let the controller and the CPU perform the complete task by them. This is much simpler and more efficient (also faster). AMIBIOS SETUP – PERIPHERAL SETUP (C)2001 American Megatrends, Inc. All Rights Reserved OnBoard FDC OnBoard Serial Port 1 OnBoard Serial Port 2 Serial Port2 Mode Duplex Mode OnBoard Prarllel Port Parallel Port Mode EPP Version Parallel Port DMA Channel Parallel Port IRQ OnBoard Serial Port3 Serial Port3 IRQ OnBoard Serial Port4 Serial Port4 Mode Serial Port4 IRQ OnBoard IDE Auto 3F8/COM1 2F8/COM2 Normal N/A 378 ECP N/A 3 7 3E8/COM3 10 2E8/COM4 Normal 11 Both Available Options: Disabled Primary Secondary Both ESC:Exit :Sel PgUp/PgDn: Modify F1:Help F2/F3:Color 37 4.10 Hardware Monitor Setup AMIBIOS SETUP – HARDWARE MONITOR SETUP (C)2001 American Megatrends, Inc. All Rights Reserved *** System Hardware Monitor *** Chassis Intrusion TSENS1 Temperature CPU Fan Speed Vcore + 2.500V +3.300V +5.000V Disabled Available Options: Disabled Enabled Reset 2.5V 3.39V 4.996V ESC:Exit :Sel PgUp/PgDn: Modify F1:Help F2/F3:Color 4.11 Auto-Detect Hard Disks This option detects the parameters of an IDE hard disk drive, and automatically enters them into the Standard CMOS Setup screen. Up to four IDE drives can be detected, with parameters for each appearing in sequence inside a box. To accept the displayed entries, press the “Y” key; to skip to the next drive, press the “N” key. If you accept the values, the parameters will appear listed beside the drive letter on the screen. AMIBIOS HIFLEX SETUP UTILITY – VERSION x.xx (C)2001 American Megatrends, Inc. All Rights Reserved Standard CMOS Setup Advanced CMOS Setup Advanced Chipset Setup Power Management Setup PCI / Plug and Play Setup Peripheral Setup Hardware Monitor Setup Auto-Detect Hard Disks Change User Password Change Supervisor Password Auto Configuration with Optimal Settings Auto Configuration with Fail Safe Settings Save Settings and Exit Exit Without Saving Standard CMOS setup for changing time, date, hard disk type, etc. ESC:Exit :Sel F2/F3: Color F10: Save & Exit 38 4.12 Change Supervisor/User Password AMIBIOS HIFLEX SETUP UTILITY – VERSION x.xx (C)2001 American Megatrends, Inc. All Rights Reserved Standard CMOS Setup Advanced CMOS Setup Advanced Chipset Setup Power Management Setup Enter new supervisor password: _ Change Supervisor Password Auto Configuration with Optimal Settings Auto Configuration with Fail Safe Settings Save Settings and Exit Exit Without Saving Standard CMOS setup for changing time, date, hard disk type, etc. ESC:Exit :Sel F2/F3: Color F10: Save & Exit You can set either supervisor or user password, or both of then. The differences between are: supervisor password: can enter and change the options of the setup menus. user password: just can only enter but do not have the right to change the options of the setup menus. When you select this function, the following message will appear at the center of the screen to assist you in creating a password. ENTER PASSWORD: Type the password, up to eight characters in length, and press . The password typed now will clear any previously entered password from CMOS memory. You will be asked to confirm the password. Type the password again and press . You may also press to abort the selection and not enter a password. To disable a password, just press when you are prompted to enter the password. A message will confirm the password will be disabled. Once the password is disabled, the system will boot and you can enter Setup freely. 39 PASSWORD DISABLED. When a password has been enabled, you will be prompted to enter it every time you try to enter Setup. This prevents an unauthorized person from changing any part of your system configuration. Additionally, when a password is enabled, you can also require the BIOS to request a password every time your system is rebooted. This would prevent unauthorized use of your computer. You determine when the password is required within the BIOS Features Setup Menu and its Security option (see Section 3). If the Security option is set to “System”, the password will be required both at boot and at entry to Setup. If set to “Setup”, prompting only occurs when trying to enter Setup. 4.13 Auto Configuration with Optimal Settings When you press on this item you will get a confirmation dialog box with a message shown below. This option allows you to load/restore the BIOS default values permanently stored in the BIOS ROM. Pressing ‘Y’ loads the BIOS default values for the most stable, minimal-performance system operations. AMIBIOS HIFLEX SETUP UTILITY – VERSION x.xx (C)2001 American Megatrends, Inc. All Rights Reserved Standard CMOS Setup Advanced CMOS Setup Advanced Chipset Setup Power Management Setup Load high performance settings (Y/N) ? N Change Supervisor Password Auto Configuration with Optimal Settings Auto Configuration with Fail Safe Settings Save Settings and Exit Exit Without Saving Standard CMOS setup for changing time, date, hard disk type, etc. ESC:Exit :Sel F2/F3: Color F10: Save & Exit 40 4.14 Auto Configuration with Fail Safe Settings When you press on this item you get a confirmation dialog box with a message similar to the figure below. This option allows you to load/restore the default values to your system configuration, optimizing and enabling all high performance features. Pressing ‘Y’ loads the default values that are factory settings for optimal performance system operations. AMIBIOS HIFLEX SETUP UTILITY – VERSION x.xx (C)2001 American Megatrends, Inc. All Rights Reserved Standard CMOS Setup Advanced CMOS Setup Advanced Chipset Setup Power Management Setup Load failsafe settings (Y/N) ? N Change Supervisor Password Auto Configuration with Optimal Settings Auto Configuration with Fail Safe Settings Save Settings and Exit Exit Without Saving Standard CMOS setup for changing time, date, hard disk type, etc. ESC:Exit :Sel F2/F3: Color F10: Save & Exit 41 4.15 Save Settings and Exit Pressing on this item asks for confirmation: AMIBIOS HIFLEX SETUP UTILITY – VERSION x.xx (C)2001 American Megatrends, Inc. All Rights Reserved Standard CMOS Setup Advanced CMOS Setup Advanced Chipset Setup Power Management Setup Save current settings and exit (Y/N) ? Y Change Supervisor Password Auto Configuration with Optimal Settings Auto Configuration with Fail Safe Settings Save Settings and Exit Exit Without Saving Standard CMOS setup for changing time, date, hard disk type, etc. ESC:Exit :Sel F2/F3: Color F10: Save & Exit Pressing “Y” stores the selections made in the menus in CMOS – a special section of memory that stays on after you turn your system off. The next time you boot your computer, the BIOS configures your system according to the Setup selections stored in CMOS. After saving the values the system is restarted again. 42 4.16 Exit Without Saving Pressing on this item asks for confirmation: Quit without saving (Y/N)? Y This allows you to exit Setup without storing in CMOS any change. The previous selections remain in effect. This exits the Setup utility and restarts your computer. AMIBIOS HIFLEX SETUP UTILITY – VERSION x.xx (C)2001 American Megatrends, Inc. All Rights Reserved Standard CMOS Setup Advanced CMOS Setup Advanced Chipset Setup Power Management Setup Quit without saving (Y/N) ? N Change Supervisor Password Auto Configuration with Optimal Settings Auto Configuration with Fail Safe Settings Save Settings and Exit Exit Without Saving Standard CMOS setup for changing time, date, hard disk type, etc. ESC:Exit :Sel F2/F3: Color F10: Save & Exit Abandon all Data & Exit Setup 43 This page is intentionally left blank. 44 Chapter 5 Software Utilities This chapter contains the detailed information of IDE, VGA and LAN driver installation procedures. 5.1 IDE Driver Installation The utility disk that came with the delivery package contains an auto-run program that invokes the installation programs for the IDE, VGA and Audio drivers. The following describes the installation procedures of each driver. 1. Insert Utility CD Disk to your CD ROM. The main menu will pop up as shown below. 45 2. Press “VIA 4 IN 1” and to go Setup. 3. Once the Welcome screen appears on the screen, make sure to close any applications running and then click on the Next button. 46 4. When the Readme window pops on the screen, you may read the whole document including the license agreement or just press Yes to skip through and continue installation. 5. The 4 in 1 Setup dialog is now displayed. Select on Normally Install and then click on Next. 47 6. The next window lists all components detected in your system and asks you to select the ones requiring drivers. Tick on all items then proceed by clicking on the Next button below the screen. 7. The program starts to install the ATAPI driver when you click the Next button on the screen below. 8. When the ATAPI driver is completely installed. The utility then displays your DMA mode status and allows you to enable it. Tick on the box and press on the Next button to continue. 48 9. The following screen then gives you the choice of installing the AGP driver in standard o turbo mode. Select on the Standard Mode and then click on Next to proceed. 10. Installation of the AGP driver is now complete. Once the screen below appears, select on restarting your computer to activate all drivers/settings completed. 49 5.2 1. VGA Driver Installation With the Utility CD Disk still in your CD ROM drive, open the File Manager and then select the CD-ROM drive. As soon as the system reads the disk, the VGA Menu screen below will appear on your display. Click on VIA_8606 from the main menu. 5.2.1 VGA Driver Installation for WIN95/98/2K 50 2. Select the operating system of your computer to proceed with the installation process. 51 3. Once the Welcome screen appears on the screen, make sure to close applications that are running and then click the Next button. 4. When the display below appears on your screen, Setup is already ready to install and copy the related files onto your hard drive. Click on the Next button to proceed. 52 5. After the installation finishes, you will be prompted to restart your system. We recommend you to reboot your computer to allow the new settings to take effect. Click on the Finish button to reboot. 5.2.2 VGA Driver Installation for WIN NT4.0 1. Click the Start button on the lower left hand corner of your screen, then select Setting. Choose Control Panel and double-click on the Display icon to launch its Display Properties window. Click on the Settings tab, and then choose Display Type. In the Change Display Type window, click on Have Disk. 53 2. Specify the path of the new driver and then press on Enter. (If in driver D:, type d:\Vga/Via_8606/Nt40) 3. Select S3 Graphics Twister 6. Click OK or press Enter. 54 7. You will see warning panel about Third Party Drivers. Click on Yes to finish the installation. 8. Once the installation is completed, you must shut down the system and restart for the new driver to take effect. 55 5.3 LAN Driver Installation 5.3.1 LAN Driver Installation for WIN95/98/2K 1. With the Utility CD Disk still in your CD ROM drive, right click on My Computer icon from the Windows menu. Select on System Properties and then proceed to the Device Manager from the main menu. 56 2. Select on Other Devices from the list of devices then double-click on PCI Ethernet Controller. 57 3. The PCI Ethernet Controller Properties screen then appears, allowing you to re-install the driver. Select Driver from the main menu to proceed. 4. The window then displays the current status of your LAN driver. Press on Update Driver button to continue. 5. The program will then launch the Update Device Driver Wizard window that will install your device driver. Click on the Next button to proceed to the next step. 58 6. When the succeeding window asks you what you wish Windows to do, tick on the “Search for a better driver….” Click on the Next button to proceed. 7. The Update Device Driver Wizard will then ask you to specify, by ticking, the path of the new driver. Tick on the open boxes where you require the program to search for the device driver then click on the Browse button to manually specify the path. 59 8. Press on the OK button as soon as you have located the path of your driver. 9. Once the program returns to the Add New Hardware Wizard screen, your specified location will appear. Press on the Next button to continue. 10. Once the program detects the device driver (*.inf) file from your specified location, it will automatically copy the files into your hard drive. 60 11. When copying of driver files finishes, the program will then ask you to insert your Windows. 12. The program then copies the necessary files from your Windows installation disk to complete the driver setup process. Once the driver is completely installed, the following message appears on your display. Click on the Finish button to proceed. 13. Restart your computer to make the new system settings take effect. Click on the Yes button when the screen below appears and your LAN Driver for Win95 and Win98 are now completely installed. 61 5.3.2 LAN Driver Installation for WIN NT4.0 1. With the Utility CD Disk still in your CD ROM drive, right click on Network Neighborhood icon from the Windows menu. Select on Properties. 2. The system automatically detects the absence of Windows NT Networking. Click on the Yes button to start installation. 62 3. Tick on the “Wired to Network” once the following screen appears. Click on the Next to proceed. 4. Click on the Start Search button for the program to locate the Network Adapter. 63 5. Once setup finishes the search, it will list a number of adapters for you to choose from. Press on the Have Disk button to assign the driver path location. 6. Setup now asks you for the location of the driver. When you have entered the new driver path, press on the OK button to continue. 64 7. When Setup finds the information it needs about the new driver, it will display the device it found on the following screen. Press on the OK button to accept and proceed. 8. Setup then returns to Network Setup Wizard screen and displays your new Network Adapter. Click on Next to continue. 65 9. The Network Setup Wizard then allows you to set the Network Protocols on your network. Select the appropriate protocol and then click on Next to continue. 10. Before Setup starts installing the components found and the settings you made, it will give you the option to proceed or go back for changes from the following screen. Click on the Next button once you are sure of your devices. 66 11. Windows NT Setup will then need to copy files necessary to update the system information. Specify the path then press Continue. 12. Once it finishes copying the files, Setup will now allow you to choose the Duplex Mode of your LAN controller. Press on the Continue button after making your selection. 67 13. When Setup asks if you wish to change the TCP/IP settings of your system, select the appropriately. The default choice is No. 14. Setup then starts the Networking installation and copies the files. 68 15. When Setup finishes copying, the TCP/IP properties of your system will then pop up on your screen like the one shown below. Make the necessary changes then click on OK to continue. 16. When the screen below appears, click on Next to continue. 69 17. Setup then prompts you that it is ready to start the network. You may complete the installation thereafter. Click on Next to continue. 18. Assign the workgroup or domain setting of your computer. Click on Next to continue. 70 19. Restart your computer once the screen below appears. Click on Finish to continue. 20. Click on the Yes button to restart your computer. The LAN driver installation for WIN NT4.0 is now complete. 71 This page is intentionally left blank. 72