LM7171BIN

LM7171 LM7171 Very High Speed, High Output Current, Voltage Feedback Amplifier Literature Number: SNOS760A LM7171 Very High Speed, High Output Current, Voltage Feedback Amplifier General Description Features The LM7171 is a high speed voltage feedback amplifier that has the slewing characteristic of a current feedback amplifier; yet it can be used in all traditional voltage feedback amplifier configurations. The LM7171 is stable for gains as low as +2 or −1. It provides a very high slew rate at 4100V/µs and a wide unity-gain bandwidth of 200 MHz while consuming only 6.5 mA of supply current. It is ideal for video and high speed signal processing applications such as HDSL and pulse amplifiers. With 100 mA output current, the LM7171 can be used for video distribution, as a transformer driver or as a laser diode driver. Operation on ± 15V power supplies allows for large signal swings and provides greater dynamic range and signal-tonoise ratio. The LM7171 offers low SFDR and THD, ideal for ADC/DAC systems. In addition, the LM7171 is specified for ± 5V operation for portable applications. The LM7171 is built on National’s advanced VIP™ III (Vertically integrated PNP) complementary bipolar process. (Typical Unless Otherwise Noted) n Easy-to-use voltage feedback topology n Very high slew rate: 4100 V/µs n Wide unity-gain bandwidth: 200 MHz n −3 dB frequency @ AV = +2: 220 MHz n Low supply current: 6.5 mA n High open loop gain: 85 dB n High output current: 100 mA n Differential gain and phase: 0.01%, 0.02˚ n Specified for ± 15V and ± 5V operation Applications n n n n n n n n HDSL and ADSL drivers Multimedia broadcast systems Professional video cameras Video amplifiers Copiers/scanners/fax HDTV amplifiers Pulse amplifiers and peak detectors CATV/fiber optics signal processing Typical Performance Large Signal Pulse Response AV = +2, VS = ± 15V 01238501 VIP™ is a trademark of National Semiconductor Corporation. © 2006 National Semiconductor Corporation DS012385 www.national.com LM7171 Very High Speed, High Output Current, Voltage Feedback Amplifier May 2006 LM7171 Absolute Maximum Ratings (Note 1) Maximum Junction Temperature (Note 4) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. ESD Tolerance (Note 2) 2.5 kV Supply Voltage (V+–V−) 36V Operating Ratings (Note 1) Junction Temperature Range LM7171AI, LM7171BI Output Short Circuit to Ground (Note 3) −40˚C ≤ TJ ≤ +85˚C Thermal Resistance (θJA) Continuous Storage Temperature Range 5.5V ≤ VS ≤ 36V Supply Voltage ± 10V Differential Input Voltage (Note 11) 150˚C −65˚C to +150˚C 8-Pin MDIP 108˚C/W 8-Pin SOIC 172˚C/W ± 15V DC Electrical Characteristics Unless otherwise specified, all limits guaranteed for TJ = 25˚C, V+ = +15V, V− = −15V, VCM = 0V, and RL = 1 kΩ. Boldface limits apply at the temperature extremes Symbol Parameter Conditions Typ (Note 5) VOS Input Offset Voltage 0.2 TC VOS Input Offset Voltage 35 LM7171AI LM7171BI Limit Limit (Note 6) (Note 6) 1 3 4 7 Units mV max µV/˚C Average Drift IB Input Bias Current 2.7 IOS Input Offset Current 0.1 RIN RO Input Resistance Common Mode 40 Differential Mode 3.3 Open Loop Output 10 10 µA 12 12 max 4 4 µA 6 6 max MΩ Ω 15 Resistance CMRR Common Mode VCM = ± 10V 105 Rejection Ratio PSRR Power Supply VS = ± 15V to ± 5V 90 Rejection Ratio VCM Input Common-Mode CMRR > 60 dB 85 75 dB 80 70 min 85 75 dB 80 70 min ± 13.35 V Voltage Range AV Large Signal Voltage RL = 1 kΩ 85 Gain (Note 7) RL = 100Ω VO Output Swing 81 RL = 1 kΩ 13.3 Output Current www.national.com Sinking, RL = 100Ω 75 70 dB 70 66 min 13 V min −13 −13 V −12.7 −12.7 max 10.5 10.5 V 9.5 9.5 min −10.5 −9.5 −9.5 V −9 −9 max 118 105 105 mA 95 95 min 95 95 mA 90 90 max 105 2 min 12.7 (Open Loop) (Note 8) dB 70 13 11.8 Sourcing, RL = 100Ω 75 75 12.7 −13.2 RL = 100Ω 80 (Continued) Unless otherwise specified, all limits guaranteed for TJ = 25˚C, V+ = +15V, V− = −15V, VCM = 0V, and RL = 1 kΩ. Boldface limits apply at the temperature extremes Symbol ISC IS Parameter Conditions Typ (Note 5) Output Current Sourcing, RL = 100Ω 100 (in Linear Region) Sinking, RL = 100Ω 100 Output Short Circuit Sourcing 140 Current Sinking 135 Supply Current LM7171AI LM7171BI Limit Limit (Note 6) (Note 6) Units mA mA 6.5 8.5 8.5 mA 9.5 9.5 max ± 15V AC Electrical Characteristics Unless otherwise specified, TJ = 25˚C, V+ = +15V, V− = −15V, VCM = 0V, and RL = 1 kΩ. Symbol SR Parameter Slew Rate (Note 9) Conditions Typ LM7171AI (Note 5) Limit Limit (Note 6) (Note 6) AV = +2, VIN = 13 VPP 4100 AV = +2, VIN = 10 VPP 3100 Unity-Gain Bandwidth −3 dB Frequency φm Phase Margin ts Settling Time (0.1%) AV = +2 LM7171BI Units V/µs 200 MHz 220 MHz 50 Deg 42 ns 5 ns AV = −1, VO = ± 5V RL = 500Ω AV = −2, VIN = ± 5V, tp Propagation Delay AD Differential Gain (Note 10) 0.01 % φD Differential Phase (Note 10) 0.02 Deg fIN = 10 kHz −110 dBc fIN = 5 MHz −75 dBc fIN = 10 kHz −115 dBc fIN = 5 MHz −55 dBc f = 10 kHz 14 f = 10 kHz 1.5 RL = 500Ω Second Harmonic (Note 12) Third Harmonic (Note 12) en Input-Referred Voltage Noise Input-Referred in Current Noise ± 5V DC Electrical Characteristics Unless otherwise specified, all limits guaranteed for TJ = 25˚C, V+ = +5V, V− = −5V, VCM = 0V, and RL = 1 kΩ. Boldface limits apply at the temperature extremes Symbol VOS TC VOS Parameter Conditions Input Offset Voltage Typ LM7171AI (Note 5) Limit Limit (Note 6) (Note 6) 1.5 3.5 mV 4 7 max 0.3 Input Offset Voltage LM7171BI 35 Units µV/˚C Average Drift IB IOS Input Bias Current 3.3 Input Offset Current 0.1 3 10 10 µA 12 12 max 4 4 µA www.national.com LM7171 ± 15V DC Electrical Characteristics LM7171 ± 5V DC Electrical Characteristics (Continued) Unless otherwise specified, all limits guaranteed for TJ = 25˚C, V+ = +5V, V− = −5V, VCM = 0V, and RL = 1 kΩ. Boldface limits apply at the temperature extremes Symbol Parameter RIN Input Resistance RO Output Resistance CMRR Common Mode Conditions Typ LM7171AI LM7171BI (Note 5) Limit Limit (Note 6) (Note 6) 6 6 Common Mode 40 Differential Mode 3.3 VCM = ± 2.5V 104 Power Supply Ω 15 VS = ± 15V to ± 5V 90 Rejection Ratio VCM Input Common-Mode CMRR > 60 dB max MΩ Rejection Ratio PSRR Units 80 70 dB 75 65 min 85 75 dB 80 70 min ± 3.2 V Voltage Range AV Large Signal Voltage RL = 1 kΩ 78 Gain (Note 7) RL = 100Ω VO Output Swing 76 RL = 1 kΩ IS min 68 dB 63 min 3.2 3.2 V 3 3 min −3.2 −3.2 V −3 −3 max 3.1 2.9 2.9 V 2.8 2.8 min −3.0 −2.9 −2.9 V −2.8 −2.8 max 29 mA min Sourcing, RL = 100Ω 31 29 28 28 Sinking, RL = 100Ω 30 29 29 mA 28 28 max (Open Loop) (Note 8) ISC dB 65 72 −3.4 Output Current 70 70 67 3.4 RL = 100Ω 75 Output Short Circuit Sourcing 135 Current Sinking 100 Supply Current mA 6.2 8 8 mA 9 9 max ± 5V AC Electrical Characteristics Unless otherwise specified, TJ = 25˚C, V+ = +5V, V− = −5V, VCM = 0V, and RL = 1 kΩ. Symbol SR Parameter Slew Rate (Note 9) Conditions AV = +2, VIN = 3.5 VPP Unity-Gain Bandwidth −3 dB Frequency φm ts AV = +2 Phase Margin Settling Time (0.1%) AV = −1, VO = ± 1V, Typ LM7171AI (Note 5) Limit LM7171BI Limit (Note 6) (Note 6) Units 950 V/µs 125 MHz 140 MHz 57 Deg 56 ns 6 ns RL = 500Ω tp Propagation Delay AV = −2, VIN = ± 1V, RL = 500Ω AD Differential Gain (Note 1) 0.02 % φD Differential Phase (Note 10) 0.03 Deg www.national.com 4 LM7171 ± 5V AC Electrical Characteristics (Continued) Unless otherwise specified, TJ = 25˚C, V+ = +5V, V− = −5V, VCM = 0V, and RL = 1 kΩ. Symbol en Parameter Conditions Second Harmonic (Note 12) fIN = 10 kHz Third Harmonic (Note 12) Input-Referred Typ LM7171AI (Note 5) Limit LM7171BI Limit (Note 6) (Note 6) Units −102 dBc fIN = 5 MHz −70 dBc fIN = 10 kHz −110 dBc fIN = 5 MHz −51 dBc f = 10 kHz 14 f = 10 kHz 1.8 Voltage Noise in Input-Referred Current Noise Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but specific performance is not guaranteed. For guaranteed specifications and the test conditions, see the Electrical Characteristics. Note 2: Human body model, 1.5 kΩ in series with 100 pF. Note 3: Applies to both single-supply and split-supply operation. Continuous short circuit operation at elevated ambient temperature can result in exceeding the maximum allowed junction temperature of 150˚C. Note 4: The maximum power dissipation is a function of TJ(MAX), θJA, and TA. The maximum allowable power dissipation at any ambient temperature is PD = (TJ(MAX)–TA)/θJA. All numbers apply for packages soldered directly into a PC board. Note 5: Typical values represent the most likely parametric norm. Note 6: All limits are guaranteed by testing or statistical analysis. Note 7: Large signal voltage gain is the total output swing divided by the input signal required to produce that swing. For VS = ± 15V, VOUT = ± 5V. For VS = ± 5V, VOUT = ± 1V. Note 8: The open loop output current is guaranteed, by the measurement of the open loop output voltage swing, using 100Ω output load. Note 9: Slew Rate is the average of the raising and falling slew rates. Note 10: Differential gain and phase are measured with AV = +2, VIN = 1 VPP at 3.58 MHz and both input and output 75Ω terminated. Note 11: Input differential voltage is applied at VS = ± 15V. Note 12: Harmonics are measured with VIN = 1 VPP, AV = +2 and RL = 100Ω. Note 13: The THD measurement at low frequency is limited by the test instrument. Connection Diagram 8-Pin DIP/SO 01238502 Top View Ordering Information Package 8-Pin SOIC 8-Pin MDIP Temperature Range Industrial Military −40˚C to +85˚C −55˚C to +125˚C Transport Media LM7171AIM Rails LM7171AIMX Tape and Reel LM7171BIM Rails LM7171BIMX Tape and Reel LM7171AIN Rails LM7171BIN Rails 5 NSC Drawing M08A N08E www.national.com LM7171 Typical Performance Characteristics unless otherwise noted, TA= 25˚C Supply Current vs. Supply Voltage Supply Current vs. Temperature 01238563 01238564 Input Offset Voltage vs. Temperature Input Bias Current vs. Temperature 01238566 01238565 Short Circuit Current vs. Temperature (Sourcing) Short Circuit Current vs. Temperature (Sinking) 01238567 www.national.com 01238568 6 Output Voltage vs. Output Current LM7171 Typical Performance Characteristics unless otherwise noted, TA= 25˚C (Continued) Output Voltage vs. Output Current 01238569 01238570 CMRR vs. Frequency PSRR vs. Frequency 01238571 01238572 PSRR vs. Frequency Open Loop Frequency Response 01238573 01238551 7 www.national.com LM7171 Typical Performance Characteristics unless otherwise noted, TA= 25˚C Open Loop Frequency Response Gain-Bandwidth Product vs. Supply Voltage 01238553 01238552 Gain-Bandwidth Product vs. Load Capacitance Large Signal Voltage Gain vs. Load 01238555 01238554 Large Signal Voltage Gain vs. Load Input Voltage Noise vs. Frequency 01238556 www.national.com (Continued) 01238557 8 Input Voltage Noise vs. Frequency LM7171 Typical Performance Characteristics unless otherwise noted, TA= 25˚C (Continued) Input Current Noise vs. Frequency 01238558 01238559 Input Current Noise vs. Frequency Slew Rate vs. Supply Voltage 01238561 01238560 Slew Rate vs. Input Voltage Slew Rate vs. Load Capacitance 01238562 01238523 9 www.national.com LM7171 Typical Performance Characteristics unless otherwise noted, TA= 25˚C Open Loop Output Impedance vs. Frequency (Continued) Open Loop Output Impedance vs Frequency 01238525 01238526 Large Signal Pulse Response AV = −1, VS = ± 5V Large Signal Pulse Response AV = −1, VS = ± 15V 01238527 01238528 Large Signal Pulse Response AV = +2, VS = ± 5V Large Signal Pulse Response AV = +2, VS = ± 15V 01238529 www.national.com 01238530 10 Small Signal Pulse Response AV = −1, VS = ± 15V LM7171 Typical Performance Characteristics unless otherwise noted, TA= 25˚C (Continued) Small Signal Pulse Response AV = −1, VS = ± 5V 01238531 01238532 Small Signal Pulse Response AV = +2, VS = ± 5V Small Signal Pulse Response AV = +2, VS = ± 15V 01238533 01238534 Closed Loop Frequency Response vs. Capacitive Load (AV = +2) Closed Loop Frequency Response vs. Supply Voltage (AV = +2) 01238535 01238536 11 www.national.com LM7171 Typical Performance Characteristics unless otherwise noted, TA= 25˚C Closed Loop Frequency Response vs. Capacitive Load (AV = +2) Closed Loop Frequency Response vs. Input Signal Level (AV = +2) 01238537 01238538 Closed Loop Frequency Response vs. Input Signal Level (AV = +2) Closed Loop Frequency Response vs. Input Signal Level (AV = +2) 01238543 01238539 Closed Loop Frequency Response vs. Input Signal Level (AV = +4) Closed Loop Frequency Response vs. Input Signal Level (AV = +2) 01238540 www.national.com (Continued) 01238544 12 Closed Loop Frequency Response vs. Input Signal Level (AV = +4) (Continued) Closed Loop Frequency Response vs. Input Signal Level (AV = +4) 01238545 01238541 Closed Loop Frequency Response vs. Input Signal Level (AV = +4) Total Harmonic Distortion vs. Frequency (Note 13) 01238546 01238542 Total Harmonic Distortion vs. Frequency (Note 13) Undistorted Output Swing vs. Frequency 01238547 01238549 13 www.national.com LM7171 Typical Performance Characteristics unless otherwise noted, TA= 25˚C LM7171 Typical Performance Characteristics unless otherwise noted, TA= 25˚C Undistorted Output Swing vs. Frequency (Continued) Undistorted Output Swing vs. Frequency 01238548 01238550 Harmonic Distortion vs. Frequency (Note 13) Harmonic Distortion vs. Frequency (Note 13) 01238574 01238575 Maximum Power Dissipation vs. Ambient Temperature 01238520 www.national.com 14 LM7171 Simplified Schematic Diagram 01238509 Note: M1 and M2 are current mirrors. 15 www.national.com LM7171 LAYOUT CONSIDERATION Application Notes Printed Circuit Board and High Speed Op Amps There are many things to consider when designing PC boards for high speed op amps. Without proper caution, it is very easy to have excessive ringing, oscillation and other degraded AC performance in high speed circuits. As a rule, the signal traces should be short and wide to provide low inductance and low impedance paths. Any unused board space needs to be grounded to reduce stray signal pickup. Critical components should also be grounded at a common point to eliminate voltage drop. Sockets add capacitance to the board and can affect high frequency performance. It is better to solder the amplifier directly into the PC board without using any socket. PERFORMANCE DISCUSSION The LM7171 is a very high speed, voltage feedback amplifier. It consumes only 6.5 mA supply current while providing a unity-gain bandwidth of 200 MHz and a slew rate of 4100V/µs. It also has other great features such as low differential gain and phase and high output current. The LM7171 is a true voltage feedback amplifier. Unlike current feedback amplifiers (CFAs) with a low inverting input impedance and a high non-inverting input impedance, both inputs of voltage feedback amplifiers (VFAs) have high impedance nodes. The low impedance inverting input in CFAs and a feedback capacitor create an additional pole that will lead to instability. As a result, CFAs cannot be used in traditional op amp circuits such as photodiode amplifiers, I-to-V converters and integrators where a feedback capacitor is required. Using Probes Active (FET) probes are ideal for taking high frequency measurements because they have wide bandwidth, high input impedance and low input capacitance. However, the probe ground leads provide a long ground loop that will produce errors in measurement. Instead, the probes can be grounded directly by removing the ground leads and probe jackets and using scope probe jacks. CIRCUIT OPERATION The class AB input stage in LM7171 is fully symmetrical and has a similar slewing characteristic to the current feedback amplifiers. In the LM7171 Simplified Schematic, Q1 through Q4 form the equivalent of the current feedback input buffer, RE the equivalent of the feedback resistor, and stage A buffers the inverting input. The triple-buffered output stage isolates the gain stage from the load to provide low output impedance. Component Selection and Feedback Resistor It is important in high speed applications to keep all component leads short. For discrete components, choose carbon composition-type resistors and mica-type capacitors. Surface mount components are preferred over discrete components for minimum inductive effect. Large values of feedback resistors can couple with parasitic capacitance and cause undesirable effects such as ringing or oscillation in high speed amplifiers. For LM7171, a feedback resistor of 510Ω gives optimal performance. SLEW RATE CHARACTERISTIC The slew rate of LM7171 is determined by the current available to charge and discharge an internal high impedance node capacitor. This current is the differential input voltage divided by the total degeneration resistor RE. Therefore, the slew rate is proportional to the input voltage level, and the higher slew rates are achievable in the lower gain configurations. A curve of slew rate versus input voltage level is provided in the “Typical Performance Characteristics”. When a very fast large signal pulse is applied to the input of an amplifier, some overshoot or undershoot occurs. By placing an external resistor such as 1 kΩ in series with the input of LM7171, the bandwidth is reduced to help lower the overshoot. COMPENSATION FOR INPUT CAPACITANCE The combination of an amplifier’s input capacitance with the gain setting resistors adds a pole that can cause peaking or oscillation. To solve this problem, a feedback capacitor with a value CF > (RG x CIN)/RF can be used to cancel that pole. For LM7171, a feedback capacitor of 2 pF is recommended. Figure 1 illustrates the compensation circuit. SLEW RATE LIMITATION If the amplifier’s input signal has too large of an amplitude at too high of a frequency, the amplifier is said to be slew rate limited; this can cause ringing in time domain and peaking in frequency domain at the output of the amplifier. In the “Typical Performance Characteristics” section, there are several curves of AV = +2 and AV = +4 versus input signal levels. For the AV = +4 curves, no peaking is present and the LM7171 responds identically to the different input signal levels of 30 mV, 100 mV and 300 mV. For the AV = +2 curves, with slight peaking occurs. This peaking at high frequency ( > 100 MHz) is caused by a large input signal at high enough frequency that exceeds the amplifier’s slew rate. The peaking in frequency response does not limit the pulse response in time domain, and the LM7171 is stable with noise gain of ≥+2. 01238510 FIGURE 1. Compensating for Input Capacitance POWER SUPPLY BYPASSING Bypassing the power supply is necessary to maintain low power supply impedance across frequency. Both positive and negative power supplies should be bypassed individu- www.national.com 16 To minimize reflection, coaxial cable with matching characteristic impedance to the signal source should be used. The other end of the cable should be terminated with the same value terminator or resistor. For the commonly used cables, RG59 has 75Ω characteristic impedance, and RG58 has 50Ω characteristic impedance. (Continued) ally by placing 0.01 µF ceramic capacitors directly to power supply pins and 2.2 µF tantalum capacitors close to the power supply pins. DRIVING CAPACITIVE LOADS Amplifiers driving capacitive loads can oscillate or have ringing at the output. To eliminate oscillation or reduce ringing, an isolation resistor can be placed as shown below in Figure 5. The combination of the isolation resistor and the load capacitor forms a pole to increase stability by adding more phase margin to the overall system. The desired performance depends on the value of the isolation resistor; the bigger the isolation resistor, the more damped the pulse response becomes. For LM7171, a 50Ω isolation resistor is recommended for initial evaluation. Figure 6 shows the LM7171 driving a 150 pF load with the 50Ω isolation resistor. 01238511 FIGURE 2. Power Supply Bypassing TERMINATION In high frequency applications, reflections occur if signals are not properly terminated. Figure 3 shows a properly terminated signal while Figure 4 shows an improperly terminated signal. 01238512 FIGURE 5. Isolation Resistor Used to Drive Capacitive Load 01238517 FIGURE 3. Properly Terminated Signal 01238513 FIGURE 6. The LM7171 Driving a 150 pF Load with a 50Ω Isolation Resistor POWER DISSIPATION The maximum power allowed to dissipate in a device is defined as: PD = (TJ(MAX) − TA)/θJA Where PD is the power dissipation in a device TJ(max) is the maximum junction temperature is the ambient temperature TA is the thermal resistance of a particular package θJA 01238518 FIGURE 4. Improperly Terminated Signal For example, for the LM7171 in a SO-8 package, the maximum power dissipation at 25˚C ambient temperature is 730 mW. 17 www.national.com LM7171 Application Notes LM7171 Application Notes (Continued) Multivibrator Thermal resistance, θJA, depends on parameters such as die size, package size and package material. The smaller the die size and package, the higher θJA becomes. The 8-pin DIP package has a lower thermal resistance (108˚C/W) than that of 8-pin SO (172˚C/W). Therefore, for higher dissipation capability, use an 8-pin DIP package. The total power dissipated in a device can be calculated as: PD = PQ + PL PQ is the quiescent power dissipated in a device with no load connected at the output. PL is the power dissipated in the device with a load connected at the output; it is not the power dissipated by the load. 01238515 Furthermore, PQ: = supply current x total supply voltage with no load P L: = output current x (voltage difference between supply voltage and output voltage of the same side of supply voltage) 01238581 For example, the total power dissipated by the LM7171 with VS = ± 15V and output voltage of 10V into 1 kΩ is P D = P Q + PL Pulse Width Modulator = (6.5 mA) x (30V) + (10 mA) x (15V − 10V) = 195 mW + 50 mW = 245 mW Application Circuit Fast Instrumentation Amplifier 01238516 Video Line Driver 01238514 01238521 01238580 www.national.com 18 LM7171 Physical Dimensions inches (millimeters) unless otherwise noted 8-Pin SOIC NS Package Number M08A 8-Pin MDIP NS Package Number N08E 19 www.national.com LM7171 Very High Speed, High Output Current, Voltage Feedback Amplifier Notes National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. For the most current product information visit us at www.national.com. LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor follows the provisions of the Product Stewardship Guide for Customers (CSP-9-111C2) and Banned Substances and Materials of Interest Specification (CSP-9-111S2) for regulatory environmental compliance. Details may be found at: www.national.com/quality/green. Lead free products are RoHS compliant. National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP® Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2011, Texas Instruments Incorporated