OPA2735AIDGKRG4

OPA734, OPA2734 OPA735, OPA2735 SBOS282B − DECEMBER 2003 − REVISED FEBRUARY 2005 0.05µV/°C max, SINGLE-SUPPLY CMOS OPERATIONAL AMPLIFIERS Zer∅-Drift Series FEATURES D D D D D D D D LOW OFFSET VOLTAGE: 5µV (max) ZERO DRIFT: 0.05µV/°C max QUIESCENT CURRENT: 750µA (max) SINGLE-SUPPLY OPERATION LOW BIAS CURRENT: 200pA (max) SHUTDOWN MicroSIZE PACKAGES WIDE SUPPLY RANGE: 2.7V to 12V DESCRIPTION The OPA734 and OPA735 series of CMOS operational amplifiers use auto-zeroing techniques to simultaneously provide low offset voltage (5µV max) and near-zero drift over time and temperature. These miniature, high-precision, low quiescent current amplifiers offer high input impedance and rail-to-rail output swing within 50mV of the rails. Either single or bipolar supplies can be used in the range of +2.7V to +12V (±1.35V to ±6V). They are optimized for low-voltage, single-supply operation. The OPA734 family includes a shutdown mode. Under logic control, the amplifiers can be switched from normal operation to a standby current that is 9µA (max) and the output placed in a high-impedance state. The single version is available in the MicroSIZE SOT23-5 (SOT23-6 for shutdown version) and the SO-8 packages. The dual version is available in the MSOP-8 and SO-8 packages (MSOP-10 only for the shutdown version). All versions are specified for operation from −40°C to +85°C. R3 RG C1 1nF 1/2 OP A2735 APPLICATIONS D D D D D D TRANSDUCER APPLICATIONS TEMPERATURE MEASUREMENTS ELECTRONIC SCALES MEDICAL INSTRUMENTATION BATTERY-POWERED INSTRUMENTS HANDHELD TEST EQUIPMENT VREF = 15V REF102 10V R1 1kΩ G=1+2 R3 10kΩ C4 1nF C2 10nF C4 1nF R3 10kΩ RG R2 1kΩ C3 1nF 1/2 OP A2735 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright  2003-2005, Texas Instruments Incorporated www.ti.com OPA734, OPA2734 OPA735, OPA2735 www.ti.com SBOS282B − DECEMBER 2003 − REVISED FEBRUARY 2005 ABSOLUTE MAXIMUM RATINGS(1) Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +13.2V Signal Input Terminals, Voltage(2) . . . . . . . . . . . (V−) − 0.5V to (V+) + 0.5V Current(2) . . . . . . . . . . . . . . . . . . . . . . . . . . . ±10mA Output Short Circuit(3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Continuous Operating Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . −40°C to +150°C Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to +150°C Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +150°C Lead Temperature (soldering, 10s) . . . . . . . . . . . . . . . . . . . . . . . . . . . +300°C ESD Rating (Human Body Model), OPA734 . . . . . . . . . . . . . . . . . . . . 1000V ESD Rating (Human Body Model), OPA735, OPA2734, OPA2735 . . . . 2000V (1) Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may degrade device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those specified is not implied. (2) Input terminals are diode-clamped to the power-supply rails. Input signals that can swing more than 0.5V beyond the supply rails should be current limited to 10mA or less. (3) Short-circuit to ground, one amplifier per package. This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. PACKAGE/ORDERING INFORMATION(1) PRODUCT Shutdown Version OPA734 ″ OPA734 ″ OPA2734 ″ Non-Shutdown Version OPA735 ″ OPA735 ″ OPA2735 ″ OPA2735 ″ SOT23-5 ″ SO-8 ″ SO-8 ″ MSOP-8 ″ DBV ″ D ″ D ″ DGK ″ −40°C to +85°C ″ −40°C to +85°C ″ −40°C to +85°C ″ −40°C to +85°C ″ NSC ″ OPA735A ″ OPA2735A ″ BGN ″ OPA735AIDBVT OPA735AIDBVR OPA735AID OPA735AIDR OPA2735AID OPA2735AIDR OPA2735AIDGKT OPA2735AIDGKR Tape and Reel, 250 Tape and Reel, 3000 Rails, 100 Tape and Reel, 2500 Rails, 100 Tape and Reel, 2500 Tape and Reel, 250 Tape and Reel, 2500 SOT23-6 ″ SO-8 ″ MSOP-10 ″ DBV ″ D ″ DGS ″ −40°C to +85°C ″ −40°C to +85°C ″ −40°C to +85°C ″ NSB ″ OPA734A ″ BGO ″ OPA734AIDBVT OPA734AIDBVR OPA734AID OPA734AIDR OPA2734AIDGST OPA2734AIDGSR Tape and Reel, 250 Tape and Reel, 3000 Rails, 100 Tape and Reel, 2500 Tape and Reel, 250 Tape and Reel, 2500 PACKAGE-LEAD PACKAGE DESIGNATOR SPECIFIED TEMPERATURE RANGE PACKAGE MARKING ORDERING NUMBER TRANSPORT MEDIA, QUANTITY (1) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI website at www.ti.com. 2 OPA734, OPA2734 OPA735, OPA2735 www.ti.com SBOS282B − DECEMBER 2003 − REVISED FEBRUARY 2005 ELECTRICAL CHARACTERISTICS: VS = ±5V (VS = +10V) Boldface limits apply over the specified temperature range, TA = −40°C to +85°C. At TA = +25°C, RL = 10kΩ connected to VS/2, and VOUT = VS/2, unless otherwise noted. OPA734, OPA2734, OPA735, OPA2735 PARAMETER OFFSET VOLTAGE Input Offset Voltage vs Temperature vs Power Supply Long-Term Stability Channel Separation, dc INPUT BIAS CURRENT Input Bias Current over Temperature Input Offset Current NOISE Input Voltage Noise, f = 0.01Hz to 1Hz Input Voltage Noise, f = 0.1Hz to 10Hz Input Voltage Noise Density, f = 1kHz Input Current Noise Density, f = 1kHz INPUT VOLTAGE RANGE Common-Mode Voltage Range Common-Mode Rejection Ratio INPUT CAPACITANCE Differential Common-Mode OPEN-LOOP GAIN Open-Loop Voltage Gain FREQUENCY RESPONSE Gain-Bandwidth Product Slew Rate OUTPUT Voltage Output Swing from Rail Short-Circuit Current Open-Loop Output Impedance Capacitive Load Drive ENABLE/SHUTDOWN tOFF tON(2) VL (amplifier is shutdown) VH (amplifier is active) IQSD (per amplifier) Input Bias Current of Enable Pin POWER SUPPLY Operating Voltage Range Quiescent Current (per amplifier) TEMPERATURE RANGE Specified Range Operating Range Storage Range Thermal Resistance SOT23-5, SOT23-6 MSOP-8, MSOP-10, SO-8 VS IQ IO = 0 −40 −40 −65 qJA 200 150 2.7 to 12 (±1.35 to ±6) 0.6 V 0.75 +85 +150 +150 mA °C °C °C °C/W °C/W °C/W AOL GBW SR (V−) + 100mV < VO < (V+) − 100mV 115 VOS dVOS/dT PSRR CONDITIONS MIN TYP 1 0.01 0.2 Note (1) 0.1 MAX 5 0.05 1.8 UNIT µV µV/°C µV/V µV/V pA pA pA µVPP µVPP nV/√Hz fA/√Hz (V+) − 1.5 130 2 10 130 1.6 1.5 20 50 ±20 125 See Typical Characteristics 1.5 150 V− (V−) + 2 4 3 (V−) + 0.8 V+ 9 V dB pF pF dB MHz V/µs mV mA Ω VS = 2.7V to 12V, VCM = 0V IB IOS en en en in VCM CMRR VCM = VS/2 VCM = VS/2 ±100 ±200 See Typical Characteristics ±200 ±300 0.8 2.5 135 40 (V−) − 0.1 115 (V−) − 0.1V < VCM < (V+) − 1.5V G = +1 RL = 10kΩ ISC f = 1MHz, IO = 0 CLOAD µs µs V V µA µA (1) 300-hour life test at 150°C demonstrated randomly distributed variation in the range of measurement limits—approximately 1µV. (2) Device requires one complete auto-zero cycle to return to V OS accuracy. 3 OPA734, OPA2734 OPA735, OPA2735 www.ti.com SBOS282B − DECEMBER 2003 − REVISED FEBRUARY 2005 PIN CONFIGURATIONS OPA735 Out V− +IN 1 2 3 SOT23− 5 4 − IN 5 V+ NC(1) − IN +IN V− 1 2 3 4 OPA735 8 7 6 5 SO− 8 NC(1) V+ OUT NC(1) OUT A 1 OPA2735 8 7 6 5 SO− MSOP− 8, 8 V+ OUT B − IN B +IN B − IN A 2 +IN A V− 3 4 OPA734 OPA734 NC(1) − IN +IN V− 1 2 3 4 SO− 8 8 7 6 5 Enable V+ OUT NC(1) OUT A 1 OPA2734 10 V+ 9 8 7 6 MSOP− 10 OUT B − IN B +IN B Enable B NSB Out V− +IN 1 2 3 6 5 4 V+ Enable − IN − IN A 2 +IN A V− Enable A 3 4 5 SOT23− (2) 6 (1) NC = No Connection (2) Pin 1 of the SOT23-6 is determined by orienting the package marking as shown in the diagram. 4 OPA734, OPA2734 OPA735, OPA2735 www.ti.com SBOS282B − DECEMBER 2003 − REVISED FEBRUARY 2005 TYPICAL CHARACTERISTICS At TA = +25°C, VS = ±5V (same as +10V). OUTPUT VOLTAGE PRODUCTION DISTRIBUTION OUTPUT VOLTAGE DRIFT PRODUCTION DISTRIBUTION Absolute Value; Centered Around Zero Population Population 0 0.005 0.010 0.015 0.020 0.025 0.030 0.035 0.040 0.045 Offset Voltage (µ V) Offset Voltage Drift (µ V/_ C) OUTPUT VOLTAGE SWING TO RAIL vs OUTPUT CURRENT 6 4 VOUT Voltage Swing (V) Input Bias Current (pA) 2 +85_ C 0 −2 −4 −6 0 5 10 15 20 25 30 35 Output Current (mA) +25_ C − 40_ C 1000 0 − 1000 − 2000 − 3000 − 4000 − 5000 − 6000 − 7000 − 8000 − 9000 − 10000 − 50 INPUT BIAS CURRENT vs TEMPERATURE − IB + IB 10 Representative Units VCM = V− − 25 0 25 50 75 85 100 125 Temperature (_ C) SUPPLY CURRENT vs TEMPERATURE INPUT BIAS CURRENT vs TEMPERATURE 1000 800 Input Bias Current (pA) 600 400 200 0 − 200 − 400 − 600 − 800 − 1000 0 − 50 − 25 0 25 50 75 85 100 125 − 50 −IB 10 Representative Units VCM = VS/2 +IB 800 Supply Current (µ A) 600 ± 6V 400 ± 1.35V 200 − 25 0 25 50 75 100 125 Temperature (_ C) Temperature (_ C) 0.050 − 5.0 − 4.5 − 4.0 − 3.5 − 3.0 − 2.5 − 2.0 − 1.5 − 1.0 − 0.5 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5 OPA734, OPA2734 OPA735, OPA2735 www.ti.com SBOS282B − DECEMBER 2003 − REVISED FEBRUARY 2005 TYPICAL CHARACTERISTICS (continued) At TA = +25°C, VS = ±5V (same as +10V). OPEN−LOOP GAIN AND PHASE MARGIN vs FREQUENCY 180 160 140 120 100 AOL (dB) 80 60 40 20 0 − 20 − 40 0.1 1 10 100 1k 10k 100k 1M Frequency (Hz) SMALL−SIGNAL RESPONSE 180 160 120 100 80 60 40 20 0 − 20 − 40 10M Output Voltage (2V/div) 140 Phase Margin (_ ) LARGE−SIGNAL RESPONSE Time (5µs/div) POSITIVE OVERVOLTAGE RECOVERY Output Output Voltage (10mV/div) Voltage (2V/div) 10 k Ω 1 0k Ω +5V OPA735 Input − 5V Time (250ns/div) Time (2.5µ s/div) NEGATIVE OVERVOLTAGE RECOVERY 1 0k Ω COMMON−MODE REJECTION RATIO vs FREQUENCY 140 120 10k Ω +5 V 100 Voltage (2V/div) OPA 73 5 CMRR (dB) Input − 5V 80 60 40 20 0 Output Time (2.5µ s/div) 1 10 100 1k 10k 100k 1M 10M Frequency (Hz) 6 OPA734, OPA2734 OPA735, OPA2735 www.ti.com SBOS282B − DECEMBER 2003 − REVISED FEBRUARY 2005 TYPICAL CHARACTERISTICS (continued) At TA = +25°C, VS = ±5V (same as +10V). POWER−SUPPLY REJECTION RATIO vs FREQUENCY 160 140 +PSRR 120 PSRR (dB) 100 80 60 40 20 0 1 10 100 1k Frequency (Hz) 10k 100k 1M 10 1 − PSRR Noise (nV/√ Hz) 1k VOLTAGE NOISE vs FREQUENCY 100 10 100 1k 10k 100k Frequency (Hz) SAMPLING FREQUENCY vs TEMPERATURE 20.0 19.5 Sampling Frequency (kHz) 19.0 18.5 18.0 17.5 17.0 16.5 16.0 − 50 − 25 VS = 2.7V VS = 12V 0.1Hz TO 10Hz NOISE 1µ V/div 1s/div 0 25 50 75 100 125 150 Temperature (_ C) SMALL−SIGNAL OVERSHOOT vs CAPACITIVE LOAD 50 40 Overshoot (%) 30 20 10 0 1 10 100 1000 Capacitance (pF) 7 OPA734, OPA2734 OPA735, OPA2735 www.ti.com SBOS282B − DECEMBER 2003 − REVISED FEBRUARY 2005 APPLICATIONS INFORMATION The OPA734 and OPA735 series of op amps are unity-gain stable and free from unexpected output phase reversal. They use auto-zeroing techniques to provide low offset voltage and demonstrate very low drift over time and temperature. Good layout practice mandates the use of a 0.1µF capacitor placed closely across the supply pins. For lowest offset voltage and precision performance, circuit layout and mechanical conditions should be optimized. Avoid temperature gradients that create thermoelectric (Seebeck) effects in thermocouple junctions formed from connecting dissimilar conductors. These thermally-generated potentials can be made to cancel by assuring that they are equal on both input terminals: 1. 2. 3. Use low thermoelectric-coefficient connections (avoid dissimilar metals). Thermally isolate components from power supplies or other heat sources. Shield op amp and input circuitry from air currents such as cooling fans. The logic input is a CMOS input. Separate logic inputs are provided for each op amp on the dual version. For battery-operated applications, this feature can be used to greatly reduce the average current and extend battery life. The enable time is 150µs, which includes one full auto-zero cycle required by the amplifier to return to VOS accuracy. Prior to returning to full accuracy, the amplifier may function properly, but with unspecified offset voltage. Disable time is 1.5µs. When disabled, the output assumes a high-impedance state. The disable state allows the OPA734 to be operated as a gated amplifier, or to have the output multiplexed onto a common analog output bus. INPUT VOLTAGE The input common-mode range extends from (V−) − 0.1V to (V+) − 1.5V. For normal operation, the inputs must be limited to this range. The common-mode rejection ratio is only valid within the specified input common-mode range. A lower supply voltage results in lower input commonmode range; therefore, attention to these values must be given when selecting the input bias voltage. For example, when operating on a single 3V power supply, commonmode range is from 0.1V below ground to half the power-supply voltage. Normally, input bias current is approximately 100pA; however, input voltages exceeding the power supplies can cause excessive current to flow in or out of the input pins. Momentary voltages greater than the power supply can be tolerated if the input current is limited to 10mA. This is easily accomplished with an input resistor, as shown in Figure 1. Following these guidelines will reduce the likelihood of junctions being at different temperatures, which can cause thermoelectric voltages of 0.1µV/°C or higher, depending on the materials used. OPERATING VOLTAGE The OPA734 and OPA735 op amp family operates with a power-supply range of +2.7V to +12V (±1.35V to ±6V). Supply voltages higher than +13.2V (absolute maximum) can permanently damage the amplifier. Parameters that vary over supply voltage or temperature are shown in the Typical Characteristics section of this data sheet. Current−limited resistor required if input voltage exceeds supply rails by ≥ 0.5V. IOVERLOAD 10mA max 50Ω VIN OPA735 +5V VOUT OPA734 ENABLE FUNCTION The enable/shutdown digital input is referenced to the V− supply voltage of the op amp. A logic HIGH enables the op amp. A valid logic HIGH is defined as > (V−) + 2V. The valid logic HIGH signal can be up to the positive supply, independent of the negative power supply voltage. A valid logic LOW is defined as < 0.8V above the V− supply pin. If dual or split power supplies are used, be sure that logic input signals are properly referred to the negative supply voltage. The Enable pin is connected to internal pull-up circuitry and will enable the device if this pin is left open circuit. 8 Figure 1. Input Current Protection INTERNAL OFFSET CORRECTION The OPA734 and OPA735 series of op amps use an auto-zero topology with a time-continuous 1.6MHz op amp in the signal path. This amplifier is zero-corrected every 100µs using a proprietary technique. Upon power-up, the amplifier requires one full auto-zero cycle of approximately 100µs in addition to the start-up time for the bias circuitry to achieve specified VOS accuracy. Prior to this time, the amplifier may function properly but with unspecified offset voltage. OPA734, OPA2734 OPA735, OPA2735 www.ti.com SBOS282B − DECEMBER 2003 − REVISED FEBRUARY 2005 Low-gain (< 20) operation demands that the auto-zero circuitry correct for common-mode rejection errors of the main amplifier. Because these errors can be larger than 0.1% of a full-scale input step change, one calibration cycle (100µs) can be required to achieve full accuracy. The term clock feedthrough describes the presence of the clock frequency in the output spectrum. In auto-zeroed op amps, clock feedthrough may result from the settling of the internal sampling capacitor, or from the small amount of charge injection that occurs during the sample-and-hold of the op amp offset voltage. Feedthrough can be minimized by keeping the source impedance relatively low (< 1kΩ) and matching the source impedance on both input terminals. If the source resistance is high (> 1kΩ) feedthrough can generally be reduced with a capacitor of 1nF or greater in parallel with the source or feedback resistors. See the circuit application examples. 1nF VEX R1 +10V RR RR OPA734 VOUT R1 VREF 1nF Figure 2. Single Op Amp Bridge Amplifier Circuit LAYOUT GUIDELINES Attention to good layout practices is always recommended. Keep traces short. When possible, use a PCB ground plane with surface-mount components placed as close to the device pins as possible. Place a 0.1µF capacitor closely across the supply pins. These guidelines should be applied throughout the analog circuit to improve performance and provide benefits such as reducing the electromagnetic-interference (EMI) susceptibility. VREF = 15V 2 REF102 10V 4 RR RR 6 G=1+2 R3 RG R1 1kΩ C1(1) 1nF 1 /2 OP A 2 7 35 R3 10kΩ C4 1nF C2(1) R 10nF G C4 1nF R3 10kΩ R2 1kΩ C3(1) 1nF NOTE: (1) Place close to input pins. 1 /2 OP A 2 7 35 Figure 3. Differential Output Bridge Amplifier 9 OPA734, OPA2734 OPA735, OPA2735 www.ti.com SBOS282B − DECEMBER 2003 − REVISED FEBRUARY 2005 C2 = 1nF R4 = 10kΩ +5V RF 300Ω OPA735 0.1V to 4.9V CF 500pF Optional filter for use with SAR− type converters operating at sampling rates of 50kHz and below. ADS8342 ADS8325 ADS1100 R1 VIN R2 VREF C1 1nF R3 10kΩ VIN ±10V ±5V 0V to 10V 0V to 5V VREF 5V 5V 5V 5V R1 42.2kΩ 20.8kΩ 20.8kΩ 10.5kΩ R2 14.7kΩ 19.6kΩ 5.11kΩ 10kΩ Figure 4. Driving ADC R4 10kΩ C3 1 µF R5 1.5MΩ R2 1kΩ C2 100nF +5V R7 10kΩ OPA735 C4 1µ F R9 10kΩ +5V 1/2 OPA2703 VOUT − 5V − 5V R6 11kΩ +5V 1/2 OPA2703 REF1112 TPS434 Thermopile R3 6.8kΩ R8 10kΩ R1 22kΩ − 5V − 5V NOTE: The TPS434, by Perkin Elmer Optoelectronics, is a thermopile detector with integrated thermistor for cold− junction reference. Figure 5. Thermopile Non-Contact Surface Temperature Measurement 10 OPA734, OPA2734 OPA735, OPA2735 www.ti.com SBOS282B − DECEMBER 2003 − REVISED FEBRUARY 2005 +5V R1 536kΩ R1 536kΩ C3 10nF OPA735 VOUT − 5V R3 268kΩ C1 5nF C2 5nF fn = R = R 1 = R2 = 2R3 1 ; where C = C 1 = C2 = C3/2 2 π RC (f n = 60Hz for values shown) Figure 6. Twin-T Notch Filter C2 68.0nF R2 2.64kΩ R3 20.8kΩ 1/2 R1 10.6kΩ VIN 1/2 OP A2 735 C1 15.0nF Cutoff frequency = 2kHz for values shown. C3 6.80nF O PA2735 VOUT NOTE: FilterPro is a low-pass filter design program available for download at no cost from TI’s web site (www.ti.com). The program can be used to easily determine component values for other cutoff frequencies or filter types. Figure 7. High DC Accuracy, 3-Pole Low-Pass Filter C1 1nF R2 10 kΩ R1 = 10 kΩ R3 10 kΩ VIN 1/2 OP A27 35 VOUT C1 1nF D1 NOTE: Dynamic range of the circuit is not reduced by the diode voltage drop since the diode is not in the signal path. Application Bulletin Precision Absolute Value Circuits (SBOA068) is available at www.ti.com and provides further information about rectifier circuits. 1/2 OP A27 35 Figure 8. Precision Full-Wave Rectifier with Full Dynamic Range 11 OPA734, OPA2734 OPA735, OPA2735 www.ti.com SBOS282B − DECEMBER 2003 − REVISED FEBRUARY 2005 1nF 1kΩ 49kΩ Enable A G = 50 OPA734 VIN A VOUT Enable B G=1 OPA734 VIN B Enable inputs are CMOS logic compatible. Figure 9. High-Precision 2-Input MUX for Programmable Gain +VS Load 2.7V to 12V OPA735 Shunt RS 10mΩ IL R1 100Ω R2 10kΩ C1 1nF VOUT = 1V/A (referred to ground) Figure 10. Low-Side Power-Supply Current Sensing 12 PACKAGE OPTION ADDENDUM www.ti.com 8-Feb-2007 PACKAGING INFORMATION Orderable Device OPA2734AIDGSR OPA2734AIDGSRG4 OPA2734AIDGST OPA2734AIDGSTG4 OPA2735AID OPA2735AIDG4 OPA2735AIDGKR OPA2735AIDGKRG4 OPA2735AIDGKT OPA2735AIDGKTG4 OPA2735AIDR OPA2735AIDRG4 OPA734AID OPA734AIDBVR OPA734AIDBVRG4 OPA734AIDBVT OPA734AIDBVTG4 OPA734AIDG4 OPA734AIDR OPA734AIDRG4 OPA735AID OPA735AIDBVR OPA735AIDBVRG4 OPA735AIDBVT OPA735AIDBVTG4 Status (1) ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE Package Type MSOP MSOP MSOP MSOP SOIC SOIC MSOP MSOP MSOP MSOP SOIC SOIC SOIC SOT-23 SOT-23 SOT-23 SOT-23 SOIC SOIC SOIC SOIC SOT-23 SOT-23 SOT-23 SOT-23 Package Drawing DGS DGS DGS DGS D D DGK DGK DGK DGK D D D DBV DBV DBV DBV D D D D DBV DBV DBV DBV Pins Package Eco Plan (2) Qty 10 10 10 10 8 8 8 8 8 8 8 8 8 6 6 6 6 8 8 8 8 5 5 5 5 2500 Green (RoHS & no Sb/Br) 2500 Green (RoHS & no Sb/Br) 250 250 100 100 Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) Lead/Ball Finish CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU MSL Peak Temp (3) Level-2-260C-1 YEAR Level-2-260C-1 YEAR Level-2-260C-1 YEAR Level-2-260C-1 YEAR Level-2-260C-1 YEAR Level-2-260C-1 YEAR Level-2-260C-1 YEAR Level-2-260C-1 YEAR Level-2-260C-1 YEAR Level-2-260C-1 YEAR Level-2-260C-1 YEAR Level-2-260C-1 YEAR Level-2-260C-1 YEAR Level-2-260C-1 YEAR Level-2-260C-1 YEAR Level-2-260C-1 YEAR Level-2-260C-1 YEAR Level-2-260C-1 YEAR Level-2-260C-1 YEAR Level-2-260C-1 YEAR Level-2-260C-1 YEAR Level-1-260C-UNLIM Level-1-260C-UNLIM Level-1-260C-UNLIM Level-1-260C-UNLIM 2500 Green (RoHS & no Sb/Br) 2500 Green (RoHS & no Sb/Br) 250 250 Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) 2500 Green (RoHS & no Sb/Br) 2500 Green (RoHS & no Sb/Br) 100 Green (RoHS & no Sb/Br) 2500 Green (RoHS & no Sb/Br) 2500 Green (RoHS & no Sb/Br) 250 250 100 Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) 2500 Green (RoHS & no Sb/Br) 2500 Green (RoHS & no Sb/Br) 100 Green (RoHS & no Sb/Br) 3000 Green (RoHS & no Sb/Br) 3000 Green (RoHS & no Sb/Br) 250 250 Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) Addendum-Page 1 PACKAGE OPTION ADDENDUM www.ti.com 8-Feb-2007 Orderable Device OPA735AIDG4 OPA735AIDR OPA735AIDRG4 (1) Status (1) ACTIVE ACTIVE ACTIVE Package Type SOIC SOIC SOIC Package Drawing D D D Pins Package Eco Plan (2) Qty 8 8 8 100 Green (RoHS & no Sb/Br) Lead/Ball Finish CU NIPDAU CU NIPDAU CU NIPDAU MSL Peak Temp (3) Level-2-260C-1 YEAR Level-2-260C-1 YEAR Level-2-260C-1 YEAR 2500 Green (RoHS & no Sb/Br) 2500 Green (RoHS & no Sb/Br) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 17-May-2007 TAPE AND REEL INFORMATION Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 17-May-2007 Device Package Pins Site Reel Diameter (mm) 330 Reel Width (mm) 12 A0 (mm) B0 (mm) K0 (mm) P1 (mm) 8 W Pin1 (mm) Quadrant 12 PKGORN T1TR-MS P PKGORN T3TR-MS P PKGORN T3TR-MS P PKGORN T3TR-MS P PKGORN T3TR-MS P OPA2734AIDGST DGS 10 MLA 5.3 3.4 1.4 OPA734AIDBVR DBV 6 MLA 180 8 6.83 7.42 1.88 8 12 OPA734AIDBVT DBV 6 MLA 180 8 6.83 7.42 1.88 8 12 OPA735AIDBVR DBV 5 MLA 180 8 6.83 7.42 1.88 8 12 OPA735AIDBVT DBV 5 MLA 180 8 6.83 7.42 1.88 8 12 TAPE AND REEL BOX INFORMATION Device OPA2734AIDGST OPA734AIDBVR OPA734AIDBVT OPA735AIDBVR OPA735AIDBVT Package DGS DBV DBV DBV DBV Pins 10 6 6 5 5 Site MLA MLA MLA MLA MLA Length (mm) 346.0 0.0 190.0 190.0 190.0 Width (mm) 346.0 0.0 212.7 212.7 212.7 Height (mm) 61.0 0.0 31.75 31.75 31.75 Pack Materials-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 17-May-2007 Pack Materials-Page 3 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Amplifiers Data Converters DSP Interface Logic Power Mgmt Microcontrollers RFID Low Power Wireless amplifier.ti.com dataconverter.ti.com dsp.ti.com interface.ti.com logic.ti.com power.ti.com microcontroller.ti.com www.ti-rfid.com www.ti.com/lpw Applications Audio Automotive Broadband Digital Control Military Optical Networking Security Telephony Video & Imaging Wireless www.ti.com/audio www.ti.com/automotive www.ti.com/broadband www.ti.com/digitalcontrol www.ti.com/military www.ti.com/opticalnetwork www.ti.com/security www.ti.com/telephony www.ti.com/video www.ti.com/wireless Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2007, Texas Instruments Incorporated