SN74LVC841ADWR

SN74LVC841A 10-BIT BUS-INTERFACE D-TYPE LATCH WITH 3-STATE OUTPUTS www.ti.com SCAS307J – MARCH 1993 – REVISED FEBRUARY 2005 FEATURES • • • • • • • • • DB, DGV, DW, OR PW PACKAGE (TOP VIEW) Operates From 1.65 V to 3.6 V Inputs Accept Voltages to 5.5 V Max tpd of 6.7 ns at 3.3 V Typical VOLP (Output Ground Bounce) 2 V at VCC = 3.3 V, TA = 25°C Ioff Supports Partial-Power-Down Mode Operation Supports Mixed-Mode Signal Operation on All Ports (5-V Input/Output Voltage With 3.3-V VCC) Latch-Up Performance Exceeds 250 mA Per JESD 17 ESD Protection Exceeds JESD 22 – 2000-V Human-Body Model (A114-A) – 200-V Machine Model (A115-A) – 1000-V Charged-Device Model (C101) OE 1D 2D 3D 4D 5D 6D 7D 8D 9D 10D GND 1 24 2 23 3 22 4 21 5 20 6 19 7 18 8 17 9 16 10 15 11 14 12 13 VCC 1Q 2Q 3Q 4Q 5Q 6Q 7Q 8Q 9Q 10Q LE DESCRIPTION/ORDERING INFORMATION This 10-bit bus-interface D-type latch is designed for 1.65-V to 3.6-V VCC operation. The SN74LVC841A is designed specifically for driving highly capacitive or relatively low-impedance loads. It is particularly suitable for implementing buffer registers, I/O ports, bidirectional bus drivers, and working registers. The ten latches are transparent D-type latches. The device has noninverting data (D) inputs and provides true data at its outputs. A buffered output-enable (OE) input can be used to place the ten outputs in either a normal logic state (high or low logic levels) or a high-impedance state. In the high-impedance state, the outputs neither load nor drive the bus lines significantly. The high-impedance state and increased drive provide the capability to drive bus lines without interface or pullup components. ORDERING INFORMATION PACKAGE (1) TA SOIC – DW SSOP – DB –40°C to 85°C TSSOP – PW TVSOP – DGV (1) ORDERABLE PART NUMBER Tube of 25 SN74LVC841ADW Reel of 2000 SN74LVC841ADWR Reel of 2000 SN74LVC841ADBR Tube of 60 SN74LVC841APW Reel of 2000 SN74LVC841APWR Reel of 250 SN74LVC841APWT Reel of 2000 SN74LVC841ADGVR TOP-SIDE MARKING LVC841A LC841A LC841A LC841A Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 1993–2005, Texas Instruments Incorporated SN74LVC841A 10-BIT BUS-INTERFACE D-TYPE LATCH WITH 3-STATE OUTPUTS www.ti.com SCAS307J – MARCH 1993 – REVISED FEBRUARY 2005 DESCRIPTION/ORDERING INFORMATION (CONTINUED) OE does not affect the internal operations of the latch. Previously stored data can be retained or new data can be entered while the outputs are in the high-impedance state. Inputs can be driven from either 3.3-V or 5-V devices. This feature allows the use of these devices as translators in a mixed 3.3-V/5-V system environment. To ensure the high-impedance state during power up or power down, OE should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver. This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs, preventing damaging current backflow through the device when it is powered down. FUNCTION TABLE INPUTS OE LE D OUTPUT Q L H H H L H L L L L X Q0 H X X Z LOGIC DIAGRAM (POSITIVE LOGIC) OE LE 1 13 C1 2 1D 1D To Nine Other Channels 2 23 1Q SN74LVC841A 10-BIT BUS-INTERFACE D-TYPE LATCH WITH 3-STATE OUTPUTS www.ti.com Absolute Maximum Ratings SCAS307J – MARCH 1993 – REVISED FEBRUARY 2005 (1) over operating free-air temperature range (unless otherwise noted) MIN MAX VCC Supply voltage range –0.5 6.5 V VI Input voltage range (2) –0.5 6.5 V –0.5 6.5 V –0.5 VCC + 0.5 state (2) UNIT VO Voltage range applied to any output in the high-impedance or power-off VO Voltage range applied to any output in the high or low state (2) (3) IIK Input clamp current VI < 0 –50 mA IOK Output clamp current VO < 0 –50 mA IO Continuous output current ±50 mA ±100 mA Continuous current through VCC or GND θJA Package thermal impedance (4) Tstg (1) (2) (3) (4) DB package 63 DGV package 86 DW package 46 PW package 88 Storage temperature range –65 V °C/W °C 150 Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. The input negative-voltage and output voltage ratings may be exceeded if the input and output current ratings are observed. The value of VCC is provided in the recommended operating conditions table. The package thermal impedance is calculated in accordance with JESD 51-7. Recommended Operating Conditions (1) VCC Supply voltage VIH High-level input voltage Operating Data retention only VCC = 1.65 V to 1.95 V MIN MAX 1.65 3.6 1.5 Low-level input voltage VI Input voltage VO Output voltage 1.7 VCC = 2.7 V to 3.6 V 2 High-level output current 0.35 × VCC 0.7 VCC = 2.7 V to 3.6 V 0.8 0 5.5 High or low state 0 VCC 3-state 0 5.5 Low-level output current ∆t/∆v Input transition rise or fall rate TA Operating free-air temperature (1) V V V –4 VCC = 2.3 V –8 VCC = 2.7 V –12 VCC = 3 V –24 VCC = 1.65 V IOL V VCC = 2.3 V to 2.7 V VCC = 1.65 V IOH V 0.65 × VCC VCC = 2.3 V to 2.7 V VCC = 1.65 V to 1.95 V VIL UNIT mA 4 VCC = 2.3 V 8 VCC = 2.7 V 12 VCC = 3 V 24 –40 mA 10 ns/V 85 °C All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. 3 SN74LVC841A 10-BIT BUS-INTERFACE D-TYPE LATCH WITH 3-STATE OUTPUTS www.ti.com SCAS307J – MARCH 1993 – REVISED FEBRUARY 2005 Electrical Characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER TEST CONDITIONS VCC IOH = –100 µA VOH 1.65 V to 3.6 V 1.2 IOH = –8 mA 2.3 V 1.7 2.7 V 2.2 3V 2.4 IOH = –24 mA 3V 2.2 IOL = 100 µA 1.65 V to 3.6 V 0.2 IOL = 4 mA 1.65 V 0.45 IOL = 8 mA 2.3 V 0.7 IOL = 12 mA 2.7 V 0.4 3V 0.55 V V 3.6 V ±5 µA Ioff VI or VO = 5.5 V 0 ±10 µA IOZ VO = 0 to 5.5 V 3.6 V ±10 µA ICC ∆ICC (1) (2) VI = 0 to 5.5 V UNIT VCC – 0.2 1.65 V IOL = 24 mA II TYP (1) MAX IOH = –4 mA IOH = –12 mA VOL MIN VI = VCC or GND IO = 0 3.6 V ≤ VI ≤ 5.5 V (2) One input at VCC – 0.6 V, 10 3.6 V Other inputs at VCC or GND 10 2.7 V to 3.6 V 500 µA µA Ci VI = VCC or GND 3.3 V 5 pF Co VO = VCC or GND 3.3 V 7 pF All typical values are at VCC = 3.3 V, TA = 25°C. This applies in the disabled state only. Timing Requirements over recommended operating free-air temperature range (unless otherwise noted) (see Figure 1) VCC = 1.8 V ± 0.15 V MIN MAX VCC = 2.5 V ± 0.2 V MIN MAX VCC = 2.7 V MIN MAX VCC = 3.3 V ± 0.3 V MIN UNIT MAX Pulse duration (1) (1) 3.3 3.3 ns tsu Setup time, data before LE↓ (1) (1) 2.1 2.1 ns th Hold time, data after LE↓ (1) (1) 1 1 ns tw (1) This information was not available at the time of publication. Switching Characteristics over recommended operating free-air temperature range (unless otherwise noted) (see Figure 1) PARAMETER tpd FROM (INPUT) D LE TO (OUTPUT) Q 4 VCC = 2.5 V ± 0.2 V MIN MAX MIN MAX (1) (1) (1) (1) (1) (1) VCC = 2.7 V MIN VCC = 3.3 V ± 0.3 V UNIT MAX MIN MAX (1) 7.5 2.4 6.7 (1) 8.6 2.7 7.6 ns ten OE Q (1) (1) (1) (1) 8.5 1.3 7.2 ns tdis OE Q (1) (1) (1) (1) 6.6 1.9 5.9 ns 1 ns tsk(o) (1) VCC = 1.8 V ± 0.2 V This information was not available at the time of publication. SN74LVC841A 10-BIT BUS-INTERFACE D-TYPE LATCH WITH 3-STATE OUTPUTS www.ti.com SCAS307J – MARCH 1993 – REVISED FEBRUARY 2005 Operating Characteristics TA = 25°C TEST CONDITIONS PARAMETER Cpd (1) Power dissipation capacitance per latch Outputs enabled Outputs disabled f = 10 MHz VCC = 1.8 V VCC = 2.5 V VCC = 3.3 V TYP TYP TYP (1) (1) 25 (1) (1) 6 UNIT pF This information was not available at the time of publication. 5 SN74LVC841A 10-BIT BUS-INTERFACE D-TYPE LATCH WITH 3-STATE OUTPUTS www.ti.com SCAS307J – MARCH 1993 – REVISED FEBRUARY 2005 PARAMETER MEASUREMENT INFORMATION VLOAD S1 RL From Output Under Test CL (see Note A) Open GND RL TEST S1 tPLH/tPHL tPLZ/tPZL tPHZ/tPZH Open VLOAD GND LOAD CIRCUIT INPUTS VCC 1.8 V ± 0.15 V 2.5 V ± 0.2 V 2.7 V 3.3 V ± 0.3 V VI tr/tf VCC VCC 2.7 V 2.7 V ≤2 ns ≤2 ns ≤2.5 ns ≤2.5 ns VM VLOAD CL RL V∆ VCC/2 VCC/2 1.5 V 1.5 V 2 × VCC 2 × VCC 6V 6V 30 pF 30 pF 50 pF 50 pF 1 kΩ 500 Ω 500 Ω 500 Ω 0.15 V 0.15 V 0.3 V 0.3 V VI Timing Input VM 0V tw tsu VI Input VM VM th VI Data Input VM VM 0V 0V VOLTAGE WAVEFORMS PULSE DURATION VOLTAGE WAVEFORMS SETUP AND HOLD TIMES VI VM Input VM 0V tPLH VM VM VOL tPHL VM VM 0V Output Waveform 1 S1 at VLOAD (see Note B) tPLH tPLZ VLOAD/2 VM tPZH VOH Output VM tPZL tPHL VOH Output VI Output Control VM VOL VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES INVERTING AND NONINVERTING OUTPUTS Output Waveform 2 S1 at GND (see Note B) VOL + V∆ VOL tPHZ VM VOH − V∆ VOH ≈0 V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES LOW- AND HIGH-LEVEL ENABLING NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω. D. The outputs are measured one at a time, with one transition per measurement. E. tPLZ and tPHZ are the same as tdis. F. tPZL and tPZH are the same as ten. G. tPLH and tPHL are the same as tpd. H. All parameters and waveforms are not applicable to all devices. Figure 1. Load Circuit and Voltage Waveforms 6 PACKAGE OPTION ADDENDUM www.ti.com 10-Dec-2020 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (°C) Device Marking (3) (4/5) (6) SN74LVC841ADBR ACTIVE SSOP DB 24 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 LC841A SN74LVC841ADW ACTIVE SOIC DW 24 25 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 LVC841A SN74LVC841APW ACTIVE TSSOP PW 24 60 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 LC841A SN74LVC841APWR ACTIVE TSSOP PW 24 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 LC841A (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of