TL34071AD


 
 
 

  
   
     SLOS097C − MARCH 1991 − REVISED AUGUST 1996 D D D D D D D Low Input Offset Voltage . . . 3 mV Max Wide Gain-Bandwidth Product . . . 4.5 MHz High Slew Rate . . . 13 V/µs Fast Settling Time . . . 1.1 µs to 0.1% Wide-Range Single-Supply Operation 4 V to 44 V Wide Input Common-Mode Range Includes Ground (VCC −) Low Total Harmonic Distortion . . . 0.02% D D D D D (A Suffix) Large Output Voltage Swing −14.7 V to 14 V (With ± 15-V Supplies) Large Capacitance Drive Capability 10,000 pF Excellent Phase Margin . . . 60° Excellent Gain Margin . . . 12 dB Output Short-Circuit Protection D OR P PACKAGE (SINGLE, TOP VIEW) OFSET N1 IN − IN + VCC − /GND 1 8 2 7 3 6 4 5 D OR P PACKAGE (DUAL, TOP VIEW) NC VCC + OUT OFSET N2 1OUT 1IN − 1IN + VCC − /GND DW PACKAGE (QUAD, TOP VIEW) 1OUT 1IN − 1IN + VCC + 2IN + 2IN − 2OUT NC 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 1 8 2 7 3 6 4 5 VCC + 2OUT 2IN − 2IN + N PACKAGE (QUAD, TOP VIEW) 4OUT 4IN − 4IN + VCC − /GND 3IN + 3IN − 3OUT NC 1OUT 1IN − 1IN + VCC + 2IN + 2IN − 2OUT 1 14 2 13 3 12 4 11 5 10 6 9 7 8 4OUT 4IN − 4IN + VCC − /GND 3IN + 3IN − 3OUT NC − No internal connection AVAILABLE OPTIONS PACKAGE TA COMPLEXITY 0°C 0 C to 70°C −40 C −40°C to 105°C PLASTIC DIP SMALL OUTLINE STANDARD GRADE PRIME GRADE STANDARD GRADE PRIME GRADE Single Dual Quad TL34071P TL34072P TL34074N TL34071AP TL34072AP TL34074AN TL34071D TL34072D TL34074DW TL34071AD TL34072AD TL34074ADW Single Dual Quad TL33071P TL33072P TL33074N TL33071AP TL33072AP TL33074AN TL33071D TL33072D TL33074DW TL33071AD TL33072AD TL33074ADW −55 C −55°C to 125°C Single TL35071P TL35071AP TL35071D TL35071AD TL35072P TL35072AP TL35072D TL35072AD Dual Quad TL35074N TL35074AN TL35074DW TL35074ADW D and DW packages are available taped and reeled. Add R suffix to device type (e.g., TL34071ADR). Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright  1996, Texas Instruments Incorporated 
 
!"#$%! & '("")% $& ! *(+,'$%! -$%). "!-('%& '!!"# %! &*)''$%!& *)" %/) %)"#& !
)$& &%"(#)%& &%$-$"- 0$""$%1. "!-('%! *"!')&&2 -!)& !% )')&&$",1 ',(-) %)&%2 ! $,, *$"$#)%)"&. • POST OFFICE BOX 655303 DALLAS, TEXAS 75265 POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443 • 1 

 
 
 

  
   
     SLOS097C − MARCH 1991 − REVISED AUGUST 1996 description Quality, low cost, bipolar fabrication with innovative design concepts are employed for the TL33071/2/4, TL34071/2/4, and TL35071/2/4 series of monolithic operational amplifiers. This series of operational amplifiers offers 4.5 MHz of gain bandwidth product, 13 V/µs slew rate, and fast settling time without the use of JFET device technology. Although this series can be operated from split supplies, it is particularly suited for single-supply operation since the common-mode input voltage range includes ground potential (VCC −). With a Darlington transistor input stage, this series exhibits high input resistance, low input offset voltage, and high gain. The all-npn output stage, characterized by no dead-band crossover distortion and large output voltage swing, provides high-capacitance drive capability, excellent phase and gain margins, low open-loop high-frequency output impedance, and symmetrical source/sink ac frequency response. The TL34071/2/4 devices are avaliable in standard or prime performance (A-suffix) grades and are specified over the commercial (0°C to 70°C) temperature range. The TL33071/2/4 devices are available in standard or prime performance (A-suffix) grades and are specified over industrial/vehicular (−40°C to 105°C) temperature range. The TL35071/2/4 devices are avaliable in standard or prime performance (A-suffix) grades and are specified over the military (− 55°C to 125°C) temperature range. These low-cost amplifiers are available in single, dual, and quad configurations and are pin compatible with the MC33071/2/4, MC34071/2/4, and MC35071/2/4 series of amplifiers. Packaging options include standard plastic DIP and SO packages. symbol Single Dual and Quad (per amplifier) OFFSET N1 IN + + IN − − IN + + IN − − OUT OFFSET N2 2 • POST OFFICE BOX 655303 DALLAS, TEXAS 75265 POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443 • OUT 

 
 
 

  
   
     SLOS097C − MARCH 1991 − REVISED AUGUST 1996 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage, VCC + (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 V Supply voltage, VCC − . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −22 V Differential input voltage, VID (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 44 V Input voltage, VI (any input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VCC ± Input current, II (each input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 1 mA Output current, IO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 80 mA Total current into VCC + . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 mA Total current out of VCC − . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 mA Duration of short-circuit current at (or below) 25°C (see Note 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . unlimited Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table Operating free-air temperature range, TA: TL3307x . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −40°C to 105°C TL3407x . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C TL3507x . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −55°C to 125°C Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C Lead temperature 1.6 mm (1/16 inch) from case for 10 seconds: D, DW, N, or P package . . . . . . . . . 260°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. All voltage values, except differential voltages, are with respect to the midpoint between VCC+ and VCC −. 2. Differential voltages are at the noninverting input with respect to the inverting input. Excessive current flows if input is brought below VCC − −0.3 V. 3. The output can be shorted to either supply. Temperature and/or supply voltages must be limited to ensure that the maximum dissipation rating is not exceeded. DISSIPATION RATING TABLE PACKAGE D DW N P TA ≤ 25 25°C C POWER RATING 725 mW 1025 mW 1150 mW 1000 mW DERATING FACTOR ABOVE TA = 25°C TA = 70 70°C C POWER RATING TA = 105 105°C C POWER RATING TA = 125 125°C C POWER RATING 5.8 mW/ mW/°C C 8.2 mW/ mW/°C C 9.2 mW/ mW/°C C 8.0 mW/°C mW/ C 464 mW 656 mW 736 mW 640 mW 261 mW 369 mW 414 mW 360 mW 145 mW 205 mW 230 mW 200 mW recommended operating conditions TL3307x Supply voltage, VCC ± Common-mode input voltage, VIC VCC = 5 V VCC ± = ± 15 V Operating free-air temperature, TA • TL3507x MAX MIN MAX MIN MAX ±2 ± 22 ±2 ± 22 ±2 ± 22 0 2.7 0 2.9 0 2.7 −15 12.7 −15 12.9 −15 12.7 −40 105 0 70 −55 125 POST OFFICE BOX 655303 DALLAS, TEXAS 75265 POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443 • TL3407x MIN UNIT V V °C 3 

 
 
 

  
   
     SLOS097C − MARCH 1991 − REVISED AUGUST 1996 electrical characteristics at specified free-air temperature, VCC ± = ±15 V (unless otherwise noted) PARAMETER VIO Input offset voltage αVIO Temperature coefficient of input offset voltage IIO Input offset current TEST CONDITIONS TA† TL3x07xA MIN TYP‡ MAX VCC = 5 V 25°C 0.5 3 1.5 5 25°C 0.5 3 1.0 5 VIC = 0, VO = 0, RS = 50 Ω VCC = ± 15 V Full range VCC = ± 15 V Full range 10 VCC = ± 15 V 25°C 7 Full range VCC = 5 V Full range 5 Input bias current VCC = ± 15 V VICR VOH VOL Common-mode input voltage range High-level output voltage Low-level output voltage −0.8 −0.7 Full range −2 −0.8 −1.5 −0.7 −1.5 25°C Full range −15 to 12.8 −15 to 12.8 V 3.7 4 3.7 4 RL = 10 kΩ 25°C 13.6 14 13.6 14 RL = 2 kΩ Full range 13.4 V 13.4 VCC + = 5 V, VCC − = 0, RL = 2 kΩ 25°C 0.1 0.3 0.1 0.3 RL = 10 kΩ 25°C −14.7 −14.3 −14.7 −14.3 RL = 2 kΩ Full range IOS Short-circuit output current CMRR Common-mode rejection ratio VIC = VICRmin, RS = 50 Ω kSVR Supply-voltage rejection ratio (∆VCC ± /∆VIO) VCC ± = ± 13.5 V to ± 16.5 V, RS = 100 Ω VO = ± 10 V, RL = 2 kΩ Source: VID = 1 V, VO = 0 Sink: VID = − 1 V, VO = 0 −13.5 Full range 25 100 No Load 100 V/mV −10 −30 −10 −30 20 30 20 30 25°C 80 97 70 97 dB 25°C 80 97 70 97 dB 25°C 3.5 Full range VCC + = 5 V, VCC − = 0, VO = 0, No Load V −13.5 25 20 25°C VO = 0, A µA −1.8 −15 to 13.2 50 nA −2 −2.3 −1.8 25°C mV 100 250 25°C Large-signal differential voltage amplification Supply current (per channel) 7 VCC + = 5 V, VCC − = 0, RL = 2 kΩ AVD ICC 100 −15 to 13.2 RS = 50 Ω UNIT µV/°C 10 −2.3 25°C MAX 7 250 25°C IIB TL3x07x MIN TYP‡ 25°C 4.5 3.5 4.7 3.4 4.4 mA 4.5 4.7 3.4 4.4 mA Full range 4.6 4.6 † Full range is 0°C to 70°C for the TL3407x devices, and − 40°C to 105°C for the TL3307x devices, and − 55°C to 125°C for the TL3507x devices. ‡ All typical values are at TA = 25°C. 4 • POST OFFICE BOX 655303 DALLAS, TEXAS 75265 POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443 • 

 
 
 

  
   
     SLOS097C − MARCH 1991 − REVISED AUGUST 1996 operating characteristics, VCC± = ±15 V, TA = 25°C TL3x07xA PARAMETER TEST CONDITIONS SR + Positive slew rate SR − Negative slew rate VI = − 10 V to 10 V, RL = 2 kΩ ts Settling time AVD = − 1, 10-V step Vn In Equivalent input noise voltage f = 1 kHz, Equivalent input noise current THD GBW AV = 1 AV = − 1 MIN TYP 8 10 TL3x07x MAX MIN TYP 8 10 MAX UNIT V/ s V/µs 13 13 To 0.1% 1.1 1.1 To 0.01% 2.2 2.2 32 32 nV/√Hz f = 1 kHz 0.22 0.22 pA/√Hz Total harmonic distortion VO = 2 V to 20 V, RL = 2 kΩ, AVD = 10, f = 10 kHz 0.02 0.02 % Gain-bandwidth product f =100 kHz 4.5 MHz BW Power bandwidth RL = 2 kΩ, AVD = 1, VO(PP) = 20 V, THD = 5.0% 200 200 kHz φm RL = 2 kΩ, CL = 0 60° 60° Phase margin RL = 2 kΩ, RL = 2 kΩ, CL = 300 pF 40° 40° 12 12 RL = 2 kΩ, CL = 300 pF 4 4 Gain margin RS = 100 Ω 3.5 4.5 CL = 0 3.5 µss dB ri Differential input resistance 150 MΩ Input capacitance VIC = 0 VIC = 0 150 Ci 2.5 2.5 pF Channel separation f = 10 kHZ 120 120 dB Open-loop output impedance f = 1 MHZ 30 30 Ω zo • POST OFFICE BOX 655303 DALLAS, TEXAS 75265 POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443 • 5 PACKAGE OPTION ADDENDUM www.ti.com 10-Dec-2020 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (°C) Device Marking (3) (4/5) (6) TL35072P ACTIVE PDIP P 8 50 RoHS & Green NIPDAU N / A for Pkg Type TL35072P (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of