MP-L

C LD-26 Rev 3 Product family data sheet / Binning & laBeling document cree® Xlamp® mP-l easyWhite™ leds Product descriPtion The XLamp MP-L easyWhite LeD eliminates traditional chromaticity binning and maximizes lumen density, enabling luminaire and bulb retrofit manufacturers to deliver consistent color and required light output to the target end user. XLamp MP-L easyWhite LeDs can reduce LeD-to-LeD color variation to within a 2-step MacAdams ellipse around the desired color temperature, which is 94% smaller than the total area of the corresponding ANSI C78.377 color region. The XLamp MP-L easyWhite LeD is the perfect choice for lighting applications where high luminous flux output is required from a single, small point source. examples of specific applications include: commercial/retail WWW.CRee.COM/XLAMP display spotlights, LED retrofit bulbs, and other indoor general illumination applications. features • Cree easyWhite color temperatures • • • High lumen density Wide viewing angle: 125° Minimum 80 CRI at 2700 K and 3000 K CCT • electrically neutral thermal path • RoHS-compliant taBle of contents Product Characteristics ............... 2 label with cree Bin code, Qty, lotCharacteristics @ 150 mA Flux # ...................................... 10 (T = 25°C)............................... 2 labelJ with customer order code, .. 10 Relative Spectral Power Distribution Qty, reel 50 mA per LED) ............... 3 (I = 1 id, Po# .......................... 10 F electrical Characteristics (TJ = 25°C)............................... 3 Relative Luminous Flux vs Current and Solder Point Temperature (Steady-State Conditions)........... 4 Typical Spatial Distribution .......... 4 Reflow Soldering Characteristics .. 5 Bin and Order-Code Format ........ 6 Performance Groups – Brightness ................................ 7 direcPerformance Groups – Chromaticity ............................. 7 Cree easyWhite Color Temperatures Plotted on the 1931 CIe Curve ................................. 8 Standard Order Codes and Bins (MP-L EasyWhite) ...................... 9 Notes ..................................... 10 Mechanical Dimensions............. 12 Tape and Reel ......................... 13 Packaging ............................... 14 label with cree Bin code, Qty, lot # ................................. aPPlications • • • Commercial/residential tional lighting LED retrofit bulbs General indoor/outdoor illumination Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. the Cree logo and XLamp are registered trademarks of Cree, Inc. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc. Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 www.cree.com/xlamp X LAMP MP-L EASYWHITE LEDS Product characteristics characteristics Solder Point Temperature Viewing Angle (FWHM) - white Temperature Coefficient of Voltage (per LED string) ESD Classification (HBM per Mil-Std-883D) Total Power, all strings @ 150 mA Total Power, all strings @ 250 mA DC Forward Current, per LeD string Reverse Current, per LeD string Forward Voltage @ 150 mA, per LED string Forward Voltage @ 250 mA, per LED string Moisture Sensitivity Level Rating (MSL) W W mA mA v v 25.0 26.5 MSL 2A unit °C degrees mV/°C 125 -30 Class 2 11.3 19.9 250 0.1 26.0 27.5 minimum typical maximum 110 fluX characteristics @ 150 ma (tJ = 25°c) The following table provides several base order codes for XLamp MP-L easyWhite LeDs. For additional order codes, as well as a complete description of the order-code nomenclature, please reference pages 6 through 9 of this document. color cct range Base order codes min luminous flux (lm) group D0 e0 B0 C0 B0 C0 B0 C0 flux (lm) 900 1000 700 800 700 800 700 800 MPLeZW-A1-0000-0000D040F MPLeZW-A1-0000-0000e040F MPLEZW-A1-0000-0000B035F MPLEZW-A1-0000-0000C035F MPLeZW-A1-0000-0000B030F MPLeZW-A1-0000-0000C030F MPLeZW-A1-0000-0000B027F MPLeZW-A1-0000-0000C027F order code 4,000 K 3,500 K easyWhite 4-Step 3,000 K Notes: • • • Cree maintains a tolerance of ±7% on flux and power measurements. Minimum CRI for easyWhite color temperatures 27F, 27H, 30F, 30H is 80. Minimum CRI for easyWhite color temperatures 35F, 35H, 40F, 40H is 77. • • Typical CRI for easyWhite color temperatures 35F, 35H, 40F, 40H is 80. Cree maintains a tolerance of ±2 on CRI measurements. 2,700 K color cct range Base order codes min luminous flux (lm) group D0 e0 B0 C0 B0 C0 B0 C0 flux (lm) 900 1000 700 800 700 800 700 800 order code 4,000 K MPLeZW-A1-0000-0000D040H MPLeZW-A1-0000-0000e040H MPLEZW-A1-0000-0000B035H MPLEZW-A1-0000-0000C035H MPLeZW-A1-0000-0000B030H MPLeZW-A1-0000-0000C030H MPLeZW-A1-0000-0000B027H MPLeZW-A1-0000-0000C027H 3,500 K easyWhite 2-Step 3,000 K 2,700 K Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc. of Cree, Inc. 2 X LAMP MP-L EASYWHITE LEDS The following graph represents typical spectral output of the XLamp MPL-EZW LED. The following graph represents typical spectral output of the XLamp MP-L easyWhite LeD with all LeDs on simultane- relative Spectral Power Distribution 150 150 mA) RelativesPectral PoWer distriBution (i =(If =ma Per led) f ously. 100 Relative Radiant Power (%) 80 60 40 20 0 400 450 500 550 600 650 700 750 Wavelength (nm) The following graph represents typical electrical characteristics of each of the three individual strings of the XLamp MPL-EZW LED. electrical characteristics (t = 25°c) J Electrical Characteristics (Tj = 25ºC) The following Relative graph represents typical electrical characteristics of an individual string of150 mA) easyWhite LeDs. Flux Output vs. Junction Temperature (If = XLamp MP-L 250 200 Forward Current (mA) 150 100 50 0 18.0 19.0 20.0 21.0 22.0 23.0 24.0 25.0 26.0 27.0 Forward Voltage (V) Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc. of Cree, Inc. 3 X LAMP MP-L EASYWHITE LEDS relative luminous fluX vs current and solder Point temPerature (steady-state conditions) The data below is representative of the XLamp MP-L easyWhite in steady-state operation with all strings driven equally at the current shown. The relative luminous flux is shown as a percentage of the light output under pulsed test conditions (t=20 ms, If=150 mA, Tsp=Tj=25°C). The XLamp MP-L EasyWhite LED is binned under these pulsed test conditions. 140 120 Luminous Flux, Relative to Pulsed (%) 100 80 150 mA 60 200 mA 250 mA 40 20 0 5 15 25 35 45 55 65 75 85 95 105 Steady-State Solder Point Temperature (°C) tyPical Typical Spatial Radiation sPatial distriBution The following graph represents typical output of the XLamp MPL-EZW LED. Pattern (If = 150 mA) 120 The following graph repres Typical Spatia 100 Relative Luminous Intensity (%) 80 60 40 20 0 -90 -60 -30 0 30 60 90 Angle (º) Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc. of Cree, Inc. 4 X LAMP MP-L EASYWHITE LEDS refloW soldering characteristics In testing, Cree has found XLamp MP-L easyWhite LeDs to be compatible with JeDeC J-STD-020C, using the parameters listed below. As a general guideline, Cree recommends that users follow the recommended soldering profile provided by the manufacturer of solder paste used. Note that this general guideline may not apply to all PCB designs and configurations of reflow soldering equipment. Profile Feature Average Ramp-Up Rate (Tsmax to Tp) Preheat: Temperature Min (Tsmin) Preheat: Temperature Max (Tsmax) Preheat: Time (tsmin to tsmax) Time Maintained Above: Temperature (TL) Time Maintained Above: Time (tL) Peak/Classification Temperature (Tp) Time Within 5°C of Actual Peak Temperature (tp) Ramp-Down Rate Time 25°C to Peak Temperature lead-Based solder 3°C/second max. 100°C 150°C 60-120 seconds 183°C 60-150 seconds 215°C 10-30 seconds 6°C/second max. 6 minutes max. lead-free solder 3°C/second max. 150°C 200°C 60-180 seconds 217°C 60-150 seconds 260°C 20-40 seconds 6°C/second max 8 minutes max. Note: All temperatures refer to the topside of the package, measured on the package body surface. Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc. of Cree, Inc. 5 X LAMP MP-L EASYWHITE LEDS Bin and order-code format Bin codes and order codes are configured in the following manner: order code Bin code Series MPL Version number Kit number SSSSSS-BB-HHHH-NNNNNNNNN Internal code Color EZW = EasyWhite SSSSSS-BB-NNN-FF-HH-HHHH Series MPL Version number Flux code Internal code Chromaticity code Color EZW = EasyWhite Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc. of Cree, Inc. 6 X LAMP MP-L EASYWHITE LEDS Performance grouPs – Brightness XLamp MP-L EasyWhite LEDs are tested for luminous flux and placed into one of the following luminous-flux groups: min. luminous flux @ 150 ma per string (lm) 600 700 800 900 1000 1100 max. luminous flux @ 150 ma per string (lm) 700 800 900 1000 1100 1200 group code A0 B0 C0 D0 e0 F0 Performance grouPs – chromaticity XLamp MP-L EasyWhite LEDs are tested for chromaticity and placed into one of the regions defined by the following bounding coordinates. easyWhite color temperatures – 4-step code cct x 0.3744 40F 4000 K 0.3782 0.3912 0.3863 0.3981 35F 3500 K 0.4040 0.4186 0.4116 0.4242 30F 3000 K 0.4322 0.4449 0.4359 0.4475 27F 2700 K 0.4573 0.4695 0.4589 y 0.3685 0.3837 0.3917 0.3758 0.3800 0.3966 0.4037 0.3865 0.3919 0.4096 0.4141 0.3960 0.3994 0.4178 0.4207 0.4021 27H 2700 K 30H 3000 K 35H 3500 K 40H 4000 K easyWhite color temperatures – 2-step code cct x 0.3784 0.3804 0.3867 0.3844 0.4030 0.4061 0.4132 0.4099 0.4291 0.4333 0.4395 0.4351 0.4528 0.4578 0.4638 0.4586 y 0.3741 0.3818 0.3857 0.3778 0.3857 0.3941 0.3976 0.3890 0.3973 0.4062 0.4084 0.3994 0.4046 0.4138 0.4152 0.4060 Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc. of Cree, Inc. 7 X LAMP MP-L EASYWHITE LEDS cree easyWhite color temPeratures Plotted on the 1931 cie curve 0.45 0.44 0.43 ANSI C78.377 Quadrangle EasyWhite "F" (4-Step) Chromaticity Regions 2700K 3000K 3500K 0.42 0.41 0.40 4500K 4000K 27F 30F CCy 0.39 0.38 40F 0.37 35F 0.36 0.35 0.40 0.41 0.42 0.36 0.37 0.38 0.39 0.43 0.44 0.45 0.46 0.47 0.48 CCx 0.45 0.44 0.43 0.42 ANSI C78.377 Quadrangle EasyWhite "H" (2-Step) Chromaticity Regions 2700K 3000K 3500K 4000K 4500K 0.41 0.40 0.39 27H 30H CCy 35H 0.38 0.37 0.36 0.35 40H 0.38 0.42 0.45 CCx Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc. of Cree, Inc. 0.49 0.36 0.37 0.39 0.40 0.41 0.43 0.44 0.46 0.47 0.48 0.49 8 X LAMP MP-L EASYWHITE LEDS standard order codes and Bins (mP-l easyWhite) The following tables list standard kit numbers and performance bins. Kit numbers completely describe an order code’s chromaticity regions and luminous flux range. Xlamp mP-l easyWhite led standard order codes min. luminous flux (lm) @ 150 ma* group flux (lm) chromaticity regions easyWhite 27F 27H Kit number 0000B027F 0000B027H 0000B030F 0000B030H 0000B035F 0000B035H 0000C027F 0000C027H 0000C030F 0000C030H 0000C035F 0000C035H 0000D040F 0000D040H 0000e040F 0000e040H B0 700 30F 30H 35F 35H 27F 27H 30F C0 800 30H 35F 35H D0 900 40F 40H 40F 40H e0 1000 For other flux and chromaticity combinations, contact Cree or an authorized distributor. * Cree XLamp MP-L EasyWhite order codes specify only a minimum flux bin and not a maximum. Cree may ship reels in flux bins higher than the minimum specified by the order code without advance notice. Shipments will always adhere to the chromaticity or DWL bin restrictions specified by the order code. Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc. of Cree, Inc. 9 X LAMP MP-L EASYWHITE LEDS notes lumen maintenance Projections Based on internal long-term reliability testing, Cree projects XLamp MP-L easyWhite LeDs to maintain a mean 70% lumen maintenance after 50,000 hours at maximum rated drive current, provided the LED solder point temperature is maintained at or below 85°C. Please read the XLamp Long-Term Lumen Maintenance application note for more details on Cree’s lumen maintenance testing and forecasting. Please read the XLamp Thermal Management application note for details on how thermal design, ambient temperature, and drive current affect the LeD junction temperature. moisture sensitivity XLamp MP-L easyWhite LeDs are shipped in sealed, moisturebarrier bags (MBB) designed for long shelf life. If XLamp MP-L easyWhite LeDs are exposed to moist environments after opening the MBB packaging but before soldering, damage to the LeD may occur during the soldering operation. The following derating table defines the maximum exposure time (in days) for an XLamp MP-L easyWhite LeD in the listed humidity and temperature conditions. LEDs with exposure time longer than the time specified below must be baked according to the baking conditions listed below. Baking conditions It is not necessary to bake all XLamp MP-L easyWhite LeDs. Only the LeDs that meet all of the following criteria must be baked: 1. 2. 3. LeDs that have been removed from the original MBB packaging LeDs that have been exposed to a humid environment longer than listed in the Moisture Sensitivity section above LeDs that have not been soldered temp. 35ºC 30ºC 25ºC 20ºC 30% maximum Percent relative humidity 40% 50% 60% 17 28 70% 1 1 2 2 80% .5 1 1 1 90% .5 1 1 1 LeDs should be baked at 80ºC for 24 hours. LeDs may be baked on the original reels. Remove LeDs from MBB packaging before baking. Do not bake parts at temperatures higher than 80ºC. This baking operation resets the exposure time as defined in the Moisture Sensitivity section above. Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc. of Cree, Inc. 10 10 X LAMP MP-L EASYWHITE LEDS storage conditions XLamp MP-L easyWhite LeDs that have been removed from the original MBB packaging but not soldered should be stored in one of the following ways: • • • Store the parts in a rigid metal container with a tight-fitting lid. Verify that the storage temperature is