MAX4383ESE

19-2012; Rev 2; 4/03 Ultra-Small, Low-Cost, 210MHz, Single-Supply Op Amps with Rail-to-Rail Outputs and Disable Features ♦ Low Cost and High Speed: 210MHz -3dB Bandwidth 55MHz 0.1dB Gain Flatness 485V/µs Slew Rate ♦ Disable Mode Places Outputs in High-Impedance State ♦ Single +4.5V to +11V Operation ♦ Rail-to-Rail Outputs ♦ Input Common-Mode Range Extends Beyond VEE ♦ Low Differential Gain/Phase: 0.02%/0.08° ♦ Low Distortion at 5MHz -65dBc SFDR -63dB Total Harmonic Distortion ♦ Ultra-Small 6-Pin SC70, 6-Pin SOT23, 10-Pin µMAX, 14-Pin TSSOP, and 20-Pin TSSOP Packages Applications Set-Top Boxes Surveillance Video Systems Battery-Powered Instruments Analog-to-Digital Converter Interface CCD Imaging Systems Video Routing and Switching Systems Digital Cameras Video-on-Demand Video Line Driver Typical Operating Circuit DISABLE Ordering Information PART TEMP RANGE PINPACKAGE MAX4380EXT-T -40°C to +85°C 6 SC70-6 TOP MARK AAV MAX4380EUT-T -40°C to +85°C 6 SOT23-6 — MAX4381EUB -40°C to +85°C 10 µMAX — MAX4382EUD -40°C to +85°C 14 TSSOP — MAX4382ESD -40°C to +85°C 14 SO — MAX4382EEE -40°C to +85°C 16 QSOP — MAX4383EUD -40°C to +85°C 14 TSSOP — MAX4383ESD -40°C to +85°C 14 SO — MAX4383ESE -40°C to +85°C 16 SO — MAX4383EEE -40°C to +85°C 16 QSOP — MAX4384EUP -40°C to +85°C 20 TSSOP — IN 75Ω Pin Configurations OUT Zo = 75Ω MAX4380 TOP VIEW 75Ω OUT 1 500Ω 500Ω VEE 2 VIDEO LINE DRIVER Rail-to-Rail is a registered trademark of Nippon Motorola, Ltd. IN+ 3 MAX4380 6 VCC 5 DISABLE 4 IN- SC70-6/SOT23-6 Pin Configurations continued at end of data sheet. ________________________________________________________________ Maxim Integrated Products For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at 1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com. 1 MAX4380–MAX4384 General Description The MAX4380–MAX4384 family of op amps are unitygain-stable devices that combine high-speed performance, Rail-to-Rail ® outputs, and high-impedance disable mode. These devices operate from a +4.5V to +11V single supply or from ±2.25V to ±5.5V dual supplies. The common-mode input voltage range extends beyond the negative power-supply rail (ground in single-supply applications). The MAX4380–MAX4384 require only 5.5mA of quiescent supply current per op amp while achieving a 210MHz -3dB bandwidth, 55MHz 0.1dB gain flatness and a 485V/µs slew rate. These devices are an excellent solution in low-power/low-voltage systems that require wide bandwidth, such as video, communications, and instrumentation. The MAX4380 single with disable is available in an ultrasmall 6-pin SC70 package. MAX4380–MAX4384 Ultra-Small, Low-Cost, 210MHz, Single-Supply Op Amps with Rail-to-Rail Outputs and Disable ABSOLUTE MAXIMUM RATINGS Supply Voltage (VCC to VEE)................................................+12V IN_-, IN_+, OUT_, DISABLE_ ...........(VEE - 0.3V) to (VCC + 0.3V) Output Short-Circuit to VCC or VEE ...........................................1s Continuous Power Dissipation (TA = +70°C) 6-Pin SC70 (derate 3.1mW/°C above +70°C) .............245mW 6-Pin SOT23 (derate 7.1mW/°C above +70°C) ...........571mW 10-Pin µMAX (derate 5.6mW/°C above +70°C) ..........444mW 14-Pin TSSOP (derate 9.1mW/°C above +70°C).........727mW 14-Pin SO (derate 8.3mW/°C above +70°C) ...............667mW 16-Pin QSOP (derate 8.3mW/°C above +70°C) ..........667mW 16-Pin Narrow SO (derate 8.7mW/°C above +70°C) ..696mW 20-Pin TSSOP (derate 10.9mW/°C above +70°C).......879mW Operating Temperature Range. ..........................-40°C to +85°C Junction Temperature ......................................................+150°C Storage Temperature Range .............................-65°C to +150°C Lead Temperature (soldering, 10s) .................................+300°C Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or at any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. DC ELECTRICAL CHARACTERISTICS–Single Supply (VCC = +5V, VEE = 0, VCM = VCC/2, VOUT = VCC/2, RL = ∞ to VCC/2, DISABLE_ = VCC (MAX4380/MAX4381/MAX4382/MAX4384), TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.) (Note 1) PARAMETER SYMBOL Input Common-Mode Voltage Range VCM Input Offset Voltage VOS Input Offset Voltage Matching Input Offset Voltage Tempco Input Bias Current Input Offset Current Input Resistance CONDITIONS MIN VEE - 0.2 Guaranteed by CMRR TA = +25°C 0.2 TA = -40°C to +85°C V 12 mV mV 8 µV/°C IB 6.5 20 0.5 7 IOS RIN Open-Loop Gain kΩ Common mode (-0.2V ≤ VCM ≤ +2.75V) 3 MΩ dB VEE - 0.2V ≤ VCM ≤ VCC - 2.25V 70 95 0.25V ≤ VOUT ≤ 4.75V, RL = 2kΩ 50 61 0.8V ≤ VOUT ≤ 4.5V, RL = 150Ω 48 RL = 150Ω VOUT RL = 75Ω RL = 75Ω to ground ISC Open-Loop Output Resistance ROUT Power-Supply Rejection Ratio PSRR µA 70 RL = 2kΩ IOUT µA Differential mode (-1V ≤ VIN ≤ +1V) 1V ≤ VOUT ≤ 4V, RL = 50Ω 2 VCC - 2.25 1 AVOL Output Short-Circuit Current UNITS 20 MAX4381–MAX4384 CMRR Output Current MAX TCVOS Common-Mode Rejection Ratio Output Voltage Swing TYP 63 VCC - VOH 0.05 0.2 VOL - VEE 0.05 0.15 0.5 VCC - VOH 0.3 VOL - VEE 0.25 0.8 VCC - VOH 0.5 0.8 VOL - VEE 0.5 1.75 VCC - VOH 1 1.7 VOL - VEE 0.025 0.125 Sinking from RL = 75Ω to VCC 40 55 Sourcing into RL = 75Ω to VEE 25 50 ±100 Sinking or sourcing VS = +4.5V to +5.5V dB 58 50 V mA mA 8 Ω 62 dB _______________________________________________________________________________________ Ultra-Small, Low-Cost, 210MHz, Single-Supply Op Amps with Rail-to-Rail Outputs and Disable (VCC = +5V, VEE = 0, VCM = VCC/2, VOUT = VCC/2, RL = ∞ to VCC/2, DISABLE_ = VCC (MAX4380/MAX4381/MAX4382/MAX4384), TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.) (Note 1) PARAMETER Operating Supply Voltage Range Disabled Output Resistance SYMBOL CONDITIONS MIN VS Guaranteed by PSRR (Note 2) 4.5 ROUT(OFF) DISABLE_ = 0, 0 ≤ VOUT ≤ 5V 27 TYP MAX UNITS 11 V 35 kΩ VCC - 3 DISABLE_ Logic-Low Threshold VIL DISABLE_ Logic-High Threshold VIH DISABLE_ Logic Input Low Current IIL DISABLE_ = 0 25 60 µA DISABLE_ Logic Input High Current IIH DISABLE_ = VCC 10 40 µA Quiescent Supply Current (Per Amplifier) IS VCC- 1.25 V V DISABLE_ = VCC 5.5 9 DISABLE_ = 0 0.45 0.6 mA DC ELECTRICAL CHARACTERISTICS–Dual Supply (V CC = +5V, V EE = -5V, V CM = 0, V OUT = 0, R L = ∞ to 0, DISABLE_ = V CC (MAX4380/MAX4381/MAX4382/MAX4384), TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.) (Note 1) PARAMETER SYMBOL Input Common-Mode Voltage Range VCM Input Offset Voltage VOS Input Offset Voltage Matching CONDITIONS MIN TYP VEE Guaranteed by CMRR TA = +25°C 3 TA = TMIN to TMAX MAX UNITS VCC - 2.25 V 16 24 MAX4381–MAX4384 1 mV mV TCVOS 8 IB 8.5 25 µA Input Offset Current IOS 0.5 12 µA Input Resistance RIN Input Offset Voltage Tempco Input Bias Current Common-Mode Rejection Ratio CMRR Open-Loop Gain AVOL Differential mode (-1V ≤ VIN ≤ +1V) 70 kΩ Common mode (-5V ≤ VCM ≤ 2.75V) 3 MΩ dB VEE ≤ VCM ≤ VCC - 2.25V 70 95 -4.5V ≤ VOUT ≤ +4.5V, RL = 2kΩ 50 62 -4.25V ≤ VOUT ≤ +4.25V, RL = 150Ω 48 65 -4V ≤ VOUT ≤ +4V, RL = 50Ω RL = 2kΩ Output Voltage Swing VOUT µV/°C RL = 150Ω RL = 75Ω dB 60 VCC - VOH 0.175 0.375 VOL - VEE 0.075 0.225 VCC - VOH 0.575 0.85 VOL - VEE 0.4 0.775 VCC - VOH 1.3 2.3 VOL - VEE 1.3 2.45 V _______________________________________________________________________________________ 3 MAX4380–MAX4384 DC ELECTRICAL CHARACTERISTICS–Single Supply MAX4380–MAX4384 Ultra-Small, Low-Cost, 210MHz, Single-Supply Op Amps with Rail-to-Rail Outputs and Disable DC ELECTRICAL CHARACTERISTICS–Dual Supply (continued) (V CC = +5V, V EE = -5V, V CM = 0, V OUT = 0, R L = ∞ to 0, DISABLE_ = V CC (MAX4380/MAX4381/MAX4382/MAX4384), TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.) (Note 1) PARAMETER Output Current Output Short-Circuit Current SYMBOL IOUT ISC Open-Loop Output Resistance ROUT Power-Supply Rejection Ratio PSRR Operating Supply Voltage Range Disabled Output Resistance VS ROUT(OFF) MIN TYP Sinking from RL = 75Ω to VCC CONDITIONS 50 75 Sourcing into RL = 75Ω to VEE 50 75 Sinking or sourcing VS = ±4.5V to ±5.5V 48 Guaranteed by PSRR (Note 2) DISABLE_ = 0, -5V ≤ VOUT ≤ 5V MAX mA ±100 mA 8 Ω 62 dB ±2.25 ±5.5 27 UNITS 35 V kΩ VCC - 3 DISABLE_ Logic-Low Threshold VIL DISABLE_ Logic-High Threshold VIH DISABLE_ Logic Input Low Current IIL DISABLE_ = 0 25 µA DISABLE_ Logic Input High Current IIH DISABLE_ = VCC 10 µA Quiescent Supply Current (Per Amplifier) IS VCC - 1.25 V V DISABLE_ = VCC 7.5 10 DISABLE_ = 0 0.45 0.8 mA AC ELECTRICAL CHARACTERISTICS–Single Supply (V CC = +5V, V EE = 0, V CM = +1.5V, R L = 100Ω to V CC /2, DISABLE_ = V CC (MAX4380/MAX4381/MAX4382/MAX4384), VOUT = VCC/2, AVCL = +1V/V, TA = +25°C, unless otherwise noted.) PARAMETER SYMBOL CONDITIONS TYP MAX UNITS BWSS VOUT = 100mVp-p 210 MHz Large-Signal -3dB Bandwidth BWLS VOUT = 2Vp-p 175 MHz Small-Signal 0.1dB Gain Flatness BW0.1dBSS VOUT = 100mVp-p 55 MHz Large-Signal 0.1dB Gain Flatness BW0.1dBLS VOUT = 2Vp-p 40 MHz Slew Rate SR VOUT = 2V step 485 V/µs Settling Time to 0.1% tS VOUT = 2V step 16 ns Rise/Fall Time tR , tF VOUT = 100mVp-p Spurious-Free Dynamic Range SFDR fC = 5MHz, VOUT = 2Vp-p 2nd harmonic Harmonic Distortion Two-Tone, Third-Order Intermodulation Distortion 4 MIN Small-Signal -3dB Bandwidth HD IP3 fC = 5MHz, VOUT = 2Vp-p 4 ns -65 dBc -65 3rd harmonic -68 Total harmonic -63 f1 = 4.7MHz, f2 = 4.8MHz, VOUT = 1Vp-p -66 _______________________________________________________________________________________ dBc dBc Ultra-Small, Low-Cost, 210MHz, Single-Supply Op Amps with Rail-to-Rail Outputs and Disable (V CC = +5V, V EE = 0, V CM = +1.5V, R L = 100Ω to V CC /2, DISABLE_ = V CC (MAX4380/MAX4381/MAX4382/MAX4384), VOUT = VCC/2, AVCL = +1V/V, TA = +25°C, unless otherwise noted.) PARAMETER SYMBOL Channel-to-Channel Isolation CONDITIONS CHISO MIN Specified at DC Input 1dB Compression Point fC = 10MHz, AVCL = +2V/V TYP MAX UNITS -102 dB 14 dBm Differential Phase Error DP NTSC, RL = 150Ω 0.08 degrees Differential Gain Error DG NTSC, RL = 150Ω 0.02 % Input Noise-Voltage Density en f = 10kHz 10 nV/√Hz Input Noise-Current Density In f = 10kHz 2 pA/√Hz 1 pF f = 10MHz 1.5 Ω 100 ns 1 µs Input Capacitance CIN Output Impedance ZOUT Enable Time tON VIN = 1V (MAX4380/MAX4381/ MAX4382/MAX4384) Disable Time tOFF VIN = 1V (MAX4380/MAX4381/ MAX4382/MAX4384) Note 1: All devices are 100% production tested at TA = +25°C. Specifications over temperature limits are guaranteed by design. Note 2: PSRR for single +5V supply tested with VEE = 0, VCC = +4.5V to +5.5V; PSRR for dual ±5V supply tested with VEE = -4.5V to -5.5V, VCC = +4.5V to +5.5V. Typical Operating Characteristics (VCC = +5V, VEE = 0, VCM = +1.5V, AVCL = +1V/V, RL = 100Ω to VCC/2, TA = +25°C, unless otherwise noted.) 1 0 0 -1 0.2 0.1 -1 0 -0.1 -2 -2 -3 -3 -0.3 -4 -4 -0.4 -5 -5 -0.5 -6 -6 -0.6 100k 1M 10M FREQUENCY (Hz) 100M 1G VOUT = 100mVp-p 0.3 GAIN (dB) 1 MAX4380-84 toc03 2 GAIN (dB) GAIN (dB) 2 VOUT = 2Vp-p 3 0.4 MAX4380-84 toc02 VOUT = 100mVp-p 3 4 MAX4380-84 toc01 4 SMALL-SIGNAL GAIN FLATNESS vs. FREQUENCY LARGE-SIGNAL GAIN vs. FREQUENCY SMALL-SIGNAL GAIN vs. FREQUENCY 100k 1M 10M FREQUENCY (Hz) 100M 1G -0.2 100k 1M 10M 100M 1G FREQUENCY (Hz) _______________________________________________________________________________________ 5 MAX4380–MAX4384 AC ELECTRICAL CHARACTERISTICS–Single Supply (continued) Typical Operating Characteristics (continued) (VCC = +5V, VEE = 0, VCM = +1.5V, AVCL = +1, RL = 100Ω to VCC/2, TA = +25°C, unless otherwise noted.) 0.1 10 IMPEDANCE (Ω) -0.1 -0.2 -0.3 -20 1 -0.4 3RD HARMONIC -90 0.01 10M 100M 1G -100 100k 1M 10M FREQUENCY (Hz) -20 2ND HARMONIC -60 VOUT = 2Vp-p AVCL = +5V/V -10 -20 -40 2ND HARMONIC -60 3RD HARMONIC -70 3RD HARMONIC -90 -100 1M 10M -20 -40 -50 -60 2ND HARMONIC -70 -80 -80 -90 -90 3RD HARMONIC -100 100k 1M 10M 100M 0 200 400 600 800 1000 DISTORTION vs. VOLTAGE SWING DIFFERENTIAL GAIN AND PHASE COMMON-MODE REJECTION vs. FREQUENCY 0.025 0.020 0.015 0.010 0.005 0 -0.005 -0.010 DIFF PHASE (degrees) 3RD HARMONIC -60 -70 2ND HARMONIC -80 -90 -100 1.0 1.5 VOLTAGE SWING (Vp-p) 2.0 1200 -20 -30 0 -50 -10 IRE 100 0.12 0.10 0.08 0.06 0.04 0.02 0 -0.02 -0.04 CMR (dB) -40 0 MAX4380-84 toc11 MAX4380-84 toc10 DIFF GAIN (%) RLOAD (Ω) -30 0.5 -30 FREQUENCY (Hz) fO = 5MHz AVCL = +1V/V -20 fO = 5MHz VOUT = 2Vp-p AVCL = +1V/V -10 FREQUENCY (Hz) 0 -10 100M 100M 0 -100 100k 10M DISTORTION vs. RESISTIVE LOAD -50 -70 -80 1M FREQUENCY (Hz) -30 DISTORTION (dBc) -30 -40 -50 100k DISTORTION vs. FREQUENCY 0 MAX4380-84 toc07 VOUT = 2Vp-p AVCL = +2V/V -10 1G FREQUENCY (Hz) DISTORTION vs. FREQUENCY 0 100M DISTORTION (dBc) 1M MAX4380-84 toc08 100k MAX4380-84 toc09 -0.7 DISTORTION (dBc) 2ND HARMONIC -60 -80 -0.6 6 -50 -70 0.1 -0.5 -30 -40 MAX4380-84 toc12 GAIN (dB) 0 VOUT = 2Vp-p AVCL = +1V/V -10 DISTORTION (dBc) VOUT = 2VP-P 0 MAX4380-84 toc05 0.2 DISTORTION vs. FREQUENCY OUTPUT IMPEDANCE vs. FREQUENCY 100 MAX4380-84 toc04 0.3 MAX4380-84 toc06 LARGE-SIGNAL GAIN FLATNESS vs. FREQUENCY DISTORTION (dBc) MAX4380–MAX4384 Ultra-Small, Low-Cost, 210MHz, Single-Supply Op Amps with Rail-to-Rail Outputs and Disable -40 -50 -60 -70 -80 -90 -100 0 IRE 100 100k 1M 10M FREQUENCY (Hz) _______________________________________________________________________________________ 100M 1G Ultra-Small, Low-Cost, 200MHz, Single-Supply Op Amps with Rail-to-Rail Outputs and Disable OUTPUT VOLTAGE SWING vs. RESISTIVE LOAD -40 -50 -60 0.5 0.4 0.3 0.1 -80 0 1M 10M 100M VCC - VOH 0.2 -70 VOL - VEE MAX4380-84 toc14b 1.0 0.8 0.6 VCC - VOH 0.4 VOL - VEE 0.2 50 100 150 200 250 300 350 400 450 500 FREQUENCY (Hz) RLOAD (Ω) SMALL-SIGNAL PULSE RESPONSE SMALL-SIGNAL PULSE RESPONSE AVCL = +1V/V 1.2 0 0 1G MAX4380-84 toc15 100k MAX4380-84 toc14a 0.6 VSUPPLY = ±5V 1.4 50 100 150 200 250 300 350 400 450 500 RLOAD (Ω) RF = 500Ω AVCL = +2V/V INPUT 25mV/div 0 SMALL-SIGNAL PULSE RESPONSE RF = 500Ω AVCL = +5V/V MAX4380-84 toc17 -30 0.7 1.6 INPUT 10mV/div INPUT 50mV/div OUTPUT 50mV/div OUTPUT 50mV/div 20ns/div OUTPUT 50mV/div 20ns/div LARGE-SIGNAL PULSE RESPONSE MAX4380-84 toc18 RF = 500Ω AVCL = +2V/V MAX4380-84 toc19 LARGE-SIGNAL PULSE RESPONSE LARGE-SIGNAL PULSE RESPONSE AVCL = +1V/V 20ns/div RF = 500Ω AVCL = +5V/V INPUT 1V/div INPUT 500mV/div INPUT 200mV/div OUTPUT 1V/div OUTPUT 1V/div OUTPUT 1V/div 20ns/div 20ns/div MAX4380-84 toc20 PSR (dB) -20 VSUPPLY = +5V MAX4380-84 toc16 MAX4380-84 toc13 -10 0.8 OUTPUT VOLTAGE SWING (V) 0 OUTPUT VOLTAGE SWING vs. RESISTIVE LOAD OUTPUT VOLTAGE SWING (V) POWER-SUPPLY REJECTION vs. FREQUENCY 20ns/div _______________________________________________________________________________________ 7 MAX4380–MAX4384 Typical Operating Characteristics (continued) (VCC = +5V, VEE = 0, VCM = +1.5V, AVCL = +1, RL = 100Ω to VCC/2, TA = +25°C, unless otherwise noted.) Typical Operating Characteristics (continued) (VCC = +5V, VEE = 0, VCM = +1.5V, AVCL = +1, RL = 100Ω to VCC/2, TA = +25°C, unless otherwise noted.) VOLTAGE NOISE vs. FREQUENCY ISOLATION RESISTANCE vs. CAPACITIVE LOAD CURRENT NOISE vs. FREQUENCY MAX4380-84 toc23 RL = 100Ω 15 14 RISO (Ω) 10 16 MAX4380-84 toc22 100 CURRENT NOISE (pA/√Hz) RL = 100Ω MAX4380-84 toc21 VOLTAGE NOISE (nV/√Hz) 100 10 13 12 11 10 1 1 1k 10k 100k 1M 10M 9 1 10 100 FREQUENCY (Hz) 10k 1k 100k 1M 10M 0 SMALL-SIGNAL BANDWIDTH vs. LOAD RESISTANCE CROSSTALK vs. FREQUENCY OPEN-LOOP GAIN vs. RESISTIVE LOAD MAX4380-84 toc24 250 CLOAD (pF) 200 150 100 80 70 OPEN-LOOP GAIN (dB) 300 60 VSUPPLY = ±5V 60 VSUPPLY = +5V 40 20 50 40 30 50 10 0 0 -60 -120 -140 1k 0.1M 10k 1M 10M 100M RLOAD (Ω) RLOAD (Ω) FREQUENCY (Hz) SHUTDOWN RESPONSE INPUT OFFSET VOLTAGE vs. TEMPERATURE INPUT BIAS CURRENT vs. TEMPERATURE 3 0 1.5V VOUT 2 1 VSUPPLY = +5V 0 -1 -2 VSUPPLY = ±5V -3 12 10 1G A4380-84toc29 DISABLE INPUT OFFSET VOLTAGE (mV) 4 MAX4380-84 toc28 5 5V INPUT BIAS CURRENT (mA) MAX4380-84 toc27 VSUPPLY = ±5V 8 6 VSUPPLY = +5V 4 2 -4 0 -5 200ns/div 0 -50 -25 0 25 50 TEMPERATURE (°C) 8 -40 -100 100 100 200 300 400 500 600 700 800 0 -20 -80 20 0 50 100 150 200 250 300 350 400 450 500 FREQUENCY (Hz) MAX4380-84 toc26 100 CROSSTALK (dB) 10 MAX4380-84 toc25 1 BANDWIDTH (MHz) MAX4380–MAX4384 Ultra-Small, Low-Cost, 210MHz, Single-Supply Op Amps with Rail-to-Rail Outputs and Disable 75 100 -50 -25 0 25 50 TEMPERATURE (°C) _______________________________________________________________________________________ 75 100 Ultra-Small, Low-Cost, 210MHz, Single-Supply Op Amps with Rail-to-Rail Outputs and Disable SUPPLY CURRENT vs. TEMPERATURE MAX4380-84 toc30 10 9 VSUPPLY = ±5V SUPPLY CURRENT (mA) 8 7 6 5 VSUPPLY = +5V 4 3 2 1 0 -50 -25 0 25 50 75 100 TEMPERATURE (°C) Pin Description PIN MAX4382 MAX4383 MAX4384 SO/TSSOP SO/QSOP TSSOP NAME FUNCTION MAX4380 MAX4381 SC70/SOT23 µMAX QSOP SO/TSSOP 6 10 4 4 4 4 5 VCC Positive Power Supply. Connect a 0.1µF capacitor to GND. 2 4 13 11 11 13 16 VEE Negative Power Supply. Connect a 0.1µF Capacitor to GND. 3 — — — — — — IN+ Noninverting Input 4 — — — — — — IN- Inverting Input 1 — — — — — — OUT 5 — — — — — — DISABLE Disable. Connect to VCC to Enable. — 3 5 5 3 3 4 INA+ Amplifier A Noninverting Input — 2 6 6 2 2 3 INA- Amplifier A Inverting Input — 1 7 7 1 1 2 OUTA — 5 1 1 — — 1 DISABLEA — 7 12 10 5 5 6 INB+ Amplifier Output Amplifier A Output Shutdown Amplifier A. Connect to VCC to Enable. Amplifier B Noninverting Input _______________________________________________________________________________________ 9 MAX4380–MAX4384 Typical Operating Characteristics (continued) (VCC = +5V, VEE = 0, VCM = +1.5V, AVCL = +1, RL = 100Ω to VCC/2, TA = +25°C, unless otherwise noted.) MAX4380–MAX4384 Ultra-Small, Low-Cost, 210MHz, Single-Supply Op Amps with Rail-to-Rail Outputs and Disable Pin Description (continued) PIN MAX4382 MAX4383 MAX4384 SO/TSSOP SO/QSOP TSSOP NAME FUNCTION MAX4380 MAX4381 SC70/SOT23 µMAX QSOP SO/TSSOP — 8 11 9 6 6 7 INB- — 9 10 8 7 7 8 OUTB — 6 3 3 — — 9 DISABLEB — — 14 12 10 12 15 INC+ Amplifier C Noninverting Input — — 15 13 9 11 14 INC- Amplifier C Inverting Input — — 16 14 8 10 13 OUTC — — 2 2 — — 12 DISABLEC — — — — 12 14 17 IND+ Amplifier D Noninverting Input — — — — 13 15 18 IND- Amplifier D Inverting Input — — — — 14 16 19 OUTD — — — — — — 20 DISABLED — — 8, 9 — — 8, 9 10, 11 N.C. Amplifier B Inverting Input Amplifier B Output Shutdown Amplifier B. Connect to VCC to Enable. Amplifier C Output Shutdown Amplifier C. Connect to VCC to Enable. Amplifier D Output Shutdown Amplifier D. Connect to VCC to Enable. No Connection. Not internally connected. Detailed Description Choosing Resistor Values The MAX4380–MAX4384 are single-supply, rail-to-rail, voltage-feedback amplifiers that employ current-feedback techniques to achieve 485V/µs slew rates and 210MHz bandwidths. Excellent harmonic distortion and differential gain/phase performance make these amplifiers an ideal choice for a wide variety of video and RF signal-processing applications. Unity-Gain Configuration The MAX4380–MAX4384 are internally compensated for unity gain. When configured for unity gain, a 24Ω resistor (RF) in series with the feedback path optimizes AC performance. This resistor improves AC response by reducing the Q of the parallel LC circuit formed by the parasitic feedback capacitance and inductance. Applications Information The output voltage swings to within 50mV of each supply rail. Local feedback around the output stage ensures low open-loop output impedance to reduce gain sensitivity to load variations. The input stage permits common-mode voltages beyond the negative supply and to within 2.25V of the positive supply rail. 10 Video Line Driver The MAX4380–MAX4384 are low-power, voltage-feedback amplifiers featuring bandwidths up to 210MHz, 0.1dB gain flatness to 55MHz. They are designed to minimize differential-gain error and differential-phase error to 0.02% and 0.08 degrees respectively. They ______________________________________________________________________________________ Ultra-Small, Low-Cost, 210MHz, Single-Supply Op Amps with Rail-to-Rail Outputs and Disable RF VOUT MAX438 _ IN VOUT = [1+ (RF / RG)] VIN Figure 1a. Noninverting Gain Configuration RG RF IN VOUT MAX438 _ VOUT = -(RF / RG) VIN • Don’t use IC sockets; they increase parasitic capacitance and inductance. • Use surface-mount instead of through-hole components for better high-frequency performance. • Use a PC board with at least two layers; it should be as free from voids as possible. • Keep signal lines as short and as straight as possible. Do not make 90° turns; round all corners. Rail-to-Rail Outputs, Ground-Sensing Inputs Figure 1b. Inverting Gain Configuration have a 16ns settling time to 0.1%, 485V/µs slew rates, and output-current-drive capability of up to 75mA making them ideal for driving video loads. Inverting and Noninverting Configurations Select the gain-setting feedback (RF) and input (RG) resistor values to fit your application. Large resistor values increase voltage noise and interact with the amplifier’s input and PC board capacitance. This can generate undesirable poles and zeros and decrease bandwidth or cause oscillations. For example, a noninverting gain-of-two configuration (RF = RG) using 1kΩ resistors, combined with 1pF of amplifier input capacitance and 1pF of PC board capacitance, causes a pole at 159MHz. Since this pole is within the amplifier bandwidth, it jeopardizes stability. Reducing the 1kΩ resistors to 100Ω extends the pole frequency to 1.59GHz, but could limit output swing by adding 200Ω in parallel with the amplifier’s load resistor (Figures 1a and 1b). Layout and Power-Supply Bypassing These amplifiers operate from a single +4.5V to +11V power supply or from dual ±2.25V to ±5.5V supplies. For For +5V single-supply operation, the input commonmode range extends from (V EE - 200mV) to (V CC - 2.25V) with excellent common-mode rejection. Beyond this range, the amplifier output is a nonlinear function of the input, but does not undergo phase reversal or latchup. For ±5V dual-supply operation, the common-mode range is from VEE to (VCC - 2.25V) For +5V single-supply operation the output swings to within 50mV of either power-supply rail with a 2kΩ load. The input ground sensing and the rail-to-rail output substantially increase the dynamic range. With a symmetric input in a single +5V application, the input can swing 2.95Vp-p and the output can swing 4.9Vp-p with minimal distortion. Low-Power Disable Mode The disable feature (DISABLE_) allows the amplifier to be placed in a low-power, high-output-impedance state. When the disable pin (DISABLE_) is active, the amplifier’s output impedance is 35kΩ. This high resistance and the low 2pF output capacitance make the MAX4380–MAX4382 and the MAX4384 ideal in RF/video multiplexer or switch applications. For larger arrays, pay careful attention to capacitive loading. Refer to the Output Capacitive Loading and Stability section. ______________________________________________________________________________________ 11 MAX4380–MAX4384 RG single-supply operation, bypass VCC to ground with a 0.1µF capacitor as close to the pin as possible. If operating with dual supplies, bypass each supply with a 0.1µF capacitor. Maxim recommends using microstrip and stripline techniques to obtain full bandwidth. To ensure that the PC board does not degrade the amplifier’s performance, design it for a frequency greater than 1GHz. Pay careful attention to inputs and outputs to avoid large parasitic capacitance. Whether or not you use a constant-impedance board, observe the following design guidelines: • Don’t use wire-wrap boards; they are too inductive. RF RG 6 5 RISO CL = 15pF 4 VOUT VIN CL Figure 2. Driving a Capacitive Load Through an Isolation Resistor 3 GAIN (dB) MAX438 _ 2 CL = 10pF 1 0 CL = 5pF -1 -2 -3 ISOLATION RESISTANCE vs. CAPACITIVE LOAD -4 100k MAX4380-84 toc23 16 15 14 RISO (Ω) 1M 10M 100M 1G FREQUENCY (Hz) Figure 4. Small-Signal Gain vs. Frequency with Load Capacitance and No Isolation Resistor 13 12 3 11 2 10 1 RISO = 15Ω CL = 47pF 0 9 0 50 100 150 200 250 300 350 400 450 500 CLOAD (pF) Figure 3. Isolation Resistance vs. Capacitive Load GAIN (dB) MAX4380–MAX4384 Ultra-Small, Low-Cost, 210MHz, Single-Supply Op Amps with Rail-to-Rail Outputs and Disable -1 CL = 68pF -2 CL = 120pF -3 -4 Output Capacitive Loading and Stability The MAX4380–MAX4384 are optimized for AC performance. They are not designed to drive highly reactive loads, which decrease phase margin and may produce excessive ringing and oscillation. Figure 2 shows a circuit that eliminates this problem. Figure 3 is a graph of the Optimal Isolation Resistor (RS) vs. Capacitive Load. Figure 4 shows how a capacitive load causes excessive peaking of the amplifier’s frequency response if the capacitor is not isolated from the amplifier by a resistor. A small isolation resistor (usually 10Ω to 15Ω) placed before the reactive load prevents ringing and oscillation. At higher capacitive loads, AC performance is controlled by the interaction of the load capacitance and the isolation resistor. Figure 5 shows the effect of a 15Ω isolation resistor on closed-loop response. 12 -5 -6 -7 100k 1M 10M 100M 1G FREQUENCY (Hz) Figure 5. Small-Signal Gain vs. Frequency with Load Capacitance and 27Ω Isolation Resistor Chip Information MAX4380 TRANSISTOR COUNT: 66 MAX4381 TRANSISTOR COUNT: 132 MAX4382 TRANSISTOR COUNT: 196 MAX4383 TRANSISTOR COUNT: 264 MAX4384 TRANSISTOR COUNT: 264 ______________________________________________________________________________________ Ultra-Small, Low-Cost, 210MHz, Single-Supply Op Amps with Rail-to-Rail Outputs and Disable TOP VIEW TOP VIEW OUTA 1 10 VCC 9 OUTB 8 INB- 4 7 INB+ 5 6 DISABLEB INA- 2 INA+ 3 VEE DISABLEA MAX4381 DISABLEA 1 16 OUTC DISABLEC 2 15 INC14 INC+ DISABLEB 3 VCC 4 µMAX-10 MAX4382 13 VEE INA+ 5 12 INB+ INA- 6 11 INB- OUTA 7 10 OUTB 9 N.C. 8 N.C. QSOP TOP VIEW TOP VIEW DISABLEA 1 14 OUTC DISABLEC 2 13 INC- INA- 2 13 IND- DISABLEB 3 12 INC+ INA+ 3 12 IND+ VCC 4 MAX4382 OUTA 1 14 OUTD MAX4383 11 VEE VCC 4 INA+ 5 10 INB+ INB+ 5 10 INC+ INA- 6 9 INB- INB- 6 9 INC- OUTA 7 8 OUTB OUTB 7 8 OUTC TSSOP/SO 11 VEE SO/TSSOP TOP VIEW TOP VIEW OUTA 1 16 OUTD INA- 2 15 IND- OUTA 2 19 OUTD INA+ 3 14 IND+ INA- 3 18 IND- MAX4383 DISABLEA 1 20 DISABLED 13 VEE INA+ 4 INB+ 5 12 INC+ VCC 5 INB- 6 11 INC- INB+ 6 15 INC+ 10 OUTC INB- 7 14 INC- OUTB 8 13 OUTC VCC 4 OUTB 7 N.C. 8 9 N.C. 17 IND+ MAX4384 DISABLEB 9 SO/QSOP 16 VEE 12 DISABLEC N.C. 10 11 N.C. TSSOP ______________________________________________________________________________________ 13 MAX4380–MAX4384 Pin Configurations (continued) Package Information SC70, 6L.EPS (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information go to www.maxim-ic.com/packages.) 6LSOT.EPS MAX4380–MAX4384 Ultra-Small, Low-Cost, 210MHz, Single-Supply Op Amps with Rail-to-Rail Outputs and Disable PACKAGE OUTLINE, SOT-23, 6L 21-0058 14 F 1 1 ______________________________________________________________________________________ Ultra-Small, Low-Cost, 210MHz, Single-Supply Op Amps with Rail-to-Rail Outputs and Disable 10LUMAX.EPS e 4X S 10 10 INCHES H ÿ 0.50±0.1 0.6±0.1 1 1 0.6±0.1 BOTTOM VIEW TOP VIEW D2 MILLIMETERS MAX DIM MIN 0.043 A 0.006 A1 0.002 A2 0.030 0.037 0.120 D1 0.116 0.118 D2 0.114 E1 0.116 0.120 0.118 E2 0.114 0.199 H 0.187 L 0.0157 0.0275 L1 0.037 REF b 0.007 0.0106 e 0.0197 BSC c 0.0035 0.0078 0.0196 REF S α 0∞ 6∞ MAX MIN 1.10 0.05 0.15 0.75 0.95 2.95 3.05 2.89 3.00 2.95 3.05 2.89 3.00 4.75 5.05 0.40 0.70 0.940 REF 0.177 0.270 0.500 BSC 0.090 0.200 0.498 REF 0∞ 6∞ E2 GAGE PLANE A2 c A b A1 E1 α D1 L L1 FRONT VIEW SIDE VIEW PROPRIETARY INFORMATION TITLE: PACKAGE OUTLINE, 10L uMAX/uSOP DOCUMENT CONTROL NO. REV. 21-0061 DIM A A1 B C e E H L N E H INCHES MILLIMETERS MAX MIN 0.069 0.053 0.010 0.004 0.014 0.019 0.007 0.010 0.050 BSC 0.150 0.157 0.228 0.244 0.016 0.050 MAX MIN 1.35 1.75 0.10 0.25 0.35 0.49 0.19 0.25 1.27 BSC 3.80 4.00 5.80 6.20 0.40 1 I 1 SOICN .EPS APPROVAL 1.27 VARIATIONS: 1 INCHES TOP VIEW DIM D D D MIN 0.189 0.337 0.386 MAX 0.197 0.344 0.394 MILLIMETERS MIN 4.80 8.55 9.80 MAX 5.00 8.75 10.00 N MS012 8 AA 14 AB 16 AC D A B e C 0∞-8∞ A1 L FRONT VIEW SIDE VIEW PROPRIETARY INFORMATION TITLE: PACKAGE OUTLINE, .150" SOIC APPROVAL DOCUMENT CONTROL NO. 21-0041 REV. B 1 1 ______________________________________________________________________________________ 15 MAX4380–MAX4384 Package Information (continued) (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information go to www.maxim-ic.com/packages.) Package Information (continued) TSSOP4.40mm.EPS (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information go to www.maxim-ic.com/packages.) QSOP.EPS MAX4380–MAX4384 Ultra-Small, Low-Cost, 210MHz, Single-Supply Op Amps with Rail-to-Rail Outputs and Disable Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 16 Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-1737-7600 © 2003 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products.