P3181TR

PRODUCT DATA SHEET ULTRA LOW DISTORTION MICROPROFILE SMD LINE MATCHING TRANSFORMER Features ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ Surface Mount Lead-free (Pb-free) Ultra low distortion RoHS compliant 7mm seated height Vacuum encapsulated IEC 60950 and UL 60950 certified UL Recognized Component P3181 Applications ∗ V.90 and V.92 (56kbps) modems ∗ Portable computers ∗ Fax/Modems DESCRIPTION P3181 is an ultra-low distortion microprofile transformer for applications where high performance and safety isolation to international standards are required in an extremely small case size. Designed specifically as a surface mount device, the P3181 features a 7mm seated height and is offered in the same package as the now familiar P2781 and P3081. The part is compliant with RoHS Directive 2002/95/EC, and suitable for lead-free and conventional placement and reflow. Despite the subminiature size, the performance is superior to that of much larger components. The P3181 offers reinforced insulation, is ideal for data communications at very high data rates, and can be matched to both 600Ω and complex impedance telephone lines. P3181 incorporates patented innovative features which enable data rates of 56kbps to be achieved. P3181 is certified to IEC 60950 and UL 60950. P3181 is a UL Recognized Component, and is supported by an IEC CB Test Certificate. Patented ETALDOC 567/13 Page 1 of 5 October 2007 P3181 SPECIFICATIONS Electrical At T = 25°C and as circuit Fig. 2 unless otherwise stated. Parameter Frequency response Return Loss Third Harmonic (1) (3) Distortion Balance Conditions 30Hz - 4kHz 200Hz - 4kHz 150Hz -10dBm in line Min 16 Typ -90 Max ±0.2 Units dB dB dBm DC - 5kHz Method TG25 50Hz DC Ambient temperature 80 - - dB Voltage (2) Isolation Operating range: Functional (4) Storage Humidity 3.88 5.5 - - kVrms kV -25 -40 - - +85 +125 95 °C °C %R.H. Lumped equivalent circuit parameters as Fig. 1 DC resistance(3), RDCP RDCS Leakage inductance, ΔL Shunt inductance, Lp Shunt loss, Rp Notes 1. Third harmonic typically exceeds other harmonics by 10dB. 2. Components 100% tested at 6.5 kVDC. 3. Caution: Passing DC through windings will permanently increase distortion. Telephone line current, etc. must be diverted using semiconductor line hold circuit. 4. Excludes shipping materials. Components are dry packed and sealed as shipped. Handle in accordance with IPC/JEDEC J-STD-033 procedure for components classified as IPC/JEDEC J-STD-020 Moisture Sensitivity Level 5a. 10mV 200Hz 10mV 200Hz Pins 4-6 Pins 1-3 200 220 4.7 14 10.8 250 280 Ω Ω mH H kΩ Equivalent Circuit Fig. 1 ½L R ½L IDEAL 1:1.1 R Patented ETALDOC 567/13 Page 2 of 5 October 2007 P3181 MATCHING RECOMMENDATIONS 600Ω MATCH AND DISTORTION TEST CIRCUIT Recommended Circuit Fig. 2 1.0:1.1 600 22µF 6 1 27nF 270 EUROPEAN CTR21 COMPLEX MATCH Recommended Circuit Fig. 3 150nF 22µF 6 1.0:1.1 1 82nF LIN E 27nF 360 TX 750 LIN E 27nF 1k TX 4 3 4 3 P3181 P3181 Note - Fig. 2: Typical distortion: excite from line at 150Hz to yield -10dBm @ 150Hz at line terminals. Typical THD at line terminals will then be -90dBm (i.e. -80dBc). For signals received from the line, the signal level present between terminals 1 and 3 of the transformer will be approximately 6dB below the signal sustained at the line terminals. Note - Figs. 2 and 3: As line side components (22μF, 27nF) are common to both 600Ω and complex matches, switching between matches can be performed solely on equipment side. When driven from a balanced (differential) TX drive with unbalanced (single-ended) high impedance recever, the following modifications can assist in giving good transhybrid loss (typically better than 18 dB across voiceband): 600Ω Fig. 4 1.0:1.1 600 22µF 6 1 15nF CTR21 Fig. 5 150nF 270 22µF 6 1.0:1.1 1 82nF TX A1 2.2k TX A1 750 2.2k * 27nF 10k 4 3 1k 4.7nF † LIN E 15nF* 10k 390 RX A TX A2 RX A TX A2 LIN E 4 3 P3181 P3181 * If components on line side to be unchanged for 600Ω/CTR21, compromise on 22nF. † 4.7nF can also be fitted on 600Ω circuit with only minor degradation. Note - Figs. 2, 3, 4 and 5: As P3181 transformer has a non-unity turns ratio, orientation in circuit should be observed Patented ETALDOC 567/13 Page 3 of 5 October 2007 P3181 CONSTRUCTION Dimensions Fig. 6 2.54 (0.1) 2.54 (0.1) Connections Fig. 7 e3 9.0 max (0.36) 7.0 max (0.28) 13.0 max (0.51) 1.1:1.0 View from top 1.77 (0.07) 1.32 (0.052) T oleranc e ± 0.3mm T erminals elec troplated pure tin (Sn) 5µm minimum. JE SD95 c ategory = e3. T erminal size : 1.5 (0.06) long, 1.32 (0.05)wide 1.5 (0.06) NOT : E Dimensions shown are in millimetres (inc hes) Dimensions shown are in millimetres (inches). Geometric centres of outline and pad grid coincide within a tolerance circle of 0.3mmØ. Observe correct orientation in circuit. ABSOLUTE MAXIMUM RATINGS (Ratings of components independent of circuit). Short term isolation voltage (2s) DC current Storage temperature 4.6 kVrms, 6.5kVDC 100μA -40°C to +125°C INTELLECTUAL PROPERTY RIGHTS ETAL, P3181, P3081 and P2781 are Trade Marks of Profec Technologies Ltd. The Trade Mark ETAL is registered at the UK Trade Marks Registry. Profec Technologies Ltd. is the owner of the design right under the Copyright Designs and Patents Act 1988 and no rights or licences are hereby granted or implied to any third party. P3181 and its associated circuit embodiment are patented. British Patent No. 2283195 US Patent No. 5879598 European Patent No. 0725719 and 1082737 China patent No. ZL 99806534.X © 1998 - 2005 Profec Technologies Ltd. Reproduction prohibited. Soldering temperature Profile peak 260°C 10s Recommended peak body temperature 245°C in accordance with IPC/JEDEC J-STD-033. Patented ETALDOC 567/13 Page 4 of 5 October 2007 P3181 SAFETY Manufactured from materials conforming to flammability requirements of UL94V-0. Distance through reinforced insulation 0.4mm minimum. Creepage and clearances in circuit are 7mm minimum where PCB pads do not exceed 3mmØ. Construction complies with IEC 60950-1, EN 60950-1 and UL 60950-1, reinforced insulation, 250Vrms maximum working voltage. CERTIFICATION Certified by BSI to IEC 60950 Third Edition (1999) (IEC CB Test Certificate No. GB592W) sub-clauses 1.5, 1.5.1, 1.5.2, 2.9, 2.9.1, 2.9.2, 2.9.3, 2.9.4, 2.9.5, 2.10, 2.10.1, 2.10.2, 2.10.3, 2.10.3.1, 2.10.3.2, 2.10.4, 2.10.5, 2.10.5.1, 2.10.7, 2.10.8, 4.7, 4.7.3, 4.7.3.1, 4.7.3.4, (Flammability Class V-0) ,5.2, 5.2.1, and 5.2.2 for a maximum working voltage of 250Vrms, nominal mains supply voltage not exceeding 250Vrms and a maximum operating temperature of +85°C in Pollution Degree 2 environment, reinforced insulation. Recognized under the Component Recognition Program of Underwriters Laboratories Inc. to US and Canadian requirements CAN/CSA C22.2 No. 60950-1-03/UL60950-1, First Edition, based on IEC 60950-1, First Edition, maximum working voltage 250Vrms, Pollution Degree 2, reinforced insulation. UL File number E203175. Additionally, Profec Technologies certifies all transformers as providing voltage isolation of 3.88kVrms, 5.5kV DC minimum. All shipments are supported by a Certificate of Conformity to current applicable safety standards. ORDERING CODE P3181 TR = Tape and Reel (Blank) = Bulk in tubes. Carrier tape width 24mm, 500 parts per 13” reel. Patented E203175 ETAL Group Oy, Kuormatie 14, FIN-03101, Nummela Telephone: +358 (0)20 7500 330 Fax: +358 (0)20 7500 333 Email: etalgroup@egruppen.com Website: www.etalgroup.com ISO 9001 FM 25326 ETALDOC 567/13 Page 5 of 5 October 2007