AU6376-GEL

AU6376-GEL USB2.0 Multi-LUN Flash Card Reader Controller Technical Reference Manual AU6376-GEL USB2.0 Multi-LUN Flash Card Reader Controller Copyright Copyright © 1997 - 2007. Alcor Micro, Corp. All Rights Reserved. No part of this data sheet may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without prior written permission from Alcor Micro, Corp. Trademark Acknowledgements The company and product names mentioned in this document may be the trademarks or registered trademarks of their manufacturers. Disclaimer Alcor Micro, Corp. reserves the right to change this product without prior notice. Alcor Micro, Corp. makes no warranty for the use of its products and bears no responsibility for any error that appear in this document. Specifications are subject to change without prior notice. Revision History Date Dec 2007 Revision 1.01W Description Modify “Table 5.8 Dynamic characteristic – remove Low speed Mode” Contact Information: Web site: http://www.alcormicro.com/ China ShenZhen Office Rm.2407-08, Industrial Bank Building No.4013, Shennan Road, ShenZhen,China. 518026 Phone: (0755) 8366-9039 Fax: (0755) 8366-9101 Los Angeles Office 9070 Rancho Park Court Rancho Cucamonga, CA 91730 USA Phone: (909) 483-8821 Fax: (909) 944-0464 Taiwan Alcor Micro, Corp. 4F, No 200 Kang Chien Rd., Nei Hu, Taipei, Taiwan, R.O.C. Phone: 886-2-8751-1984 Fax: 886-2-2659-7723 Santa Clara Office 2901 Tasman Drive, Suite 206 Santa Clara, CA 95054 USA Phone: (408) 845-9300 Fax: (408) 845-9086  Table of Contents 1. Introduction ............................................................ 1 1.1 Description ...................................................................................1 1.2 Features........................................................................................1 2. Application Block Diagram ................................... 2 3. Pin Assignment ...................................................... 3 4. System Architecture and Reference Design ....... 8 4.1 AU6376 Block Diagram ...............................................................8 5. Electrical Characteristics ...................................... 9 5.1 Absolute Maximum Ratings........................................................9 5.2 Recommended Operating Conditions .......................................9 5.3 General DC Characteristics ........................................................9 5.4 DC Electrical Characteristics of 3.3V I/O Cells..........................10 5.5 USB Transceiver Characteristics ...............................................10 5.6 Power Switch Feature .................................................................13 6. Mechanical Information ......................................... 14 7. Abbreviations ......................................................... 15 i List of Figures Figure 2.1 Block Diagram..................................................................2 Figure 3.1 AU6376-GEL Pin Assignment Diagram ..........................3 Figure 4.1 AU6376 Block Diagram ...................................................8 Figure 5.1 Built-in card power switch I-V curve ..............................13 Figure 5.2 Card Detect Power-in Timing ..........................................13 Figure 6.1 Mechanical Information Diagram ...................................14 List of Tables Table 3.1 AU6376-GEL Pin Descriptions .........................................4 Table 5.1 Absolute Maximum Ratings .............................................9 Table 5.2 Recommended Operating Conditions .............................9 Table 5.3 General DC Characteristics ..............................................9 Table 5.4 DC Electrical Characteristics of 3.3V I/O Cells ...............10 Table 5.5 Electrical characteristics ..................................................10 Table 5.6 Static characteristic：Digital pin .....................................11 Table 5.7 Static characteristic：Analog I/O pins（DP/DM） ..........11 Table 5.8 Dynamic characteristic：Analog I/O pins（DP/DM）.....12 ii 1. Introduction 1.1 Description The AU6376 is a single chip integrated USB 2.0 multimedia card reader controller that enables PC/DVD/Printer to read/write various type of flash media cards. Flash media cards such as CF, SMC, XD, SD, MMC, Memory Stick are widely used in digital camera, cell phone, PDA and MP3 player to store digital photos and compressed music. Performance of AU6376-GEL is maximized by implementing the latest and fastest card specification available form the industry. Especially, AU6376-GEL is designed with the high performance characteristic in flash card I/O speed. Users can easy and fast transfer the digital content among the different flash card. 1.2 Features Support USB V2.0 specification and USB Device Class Definition for Mass Storage, Bulk-Transport V1.0 Support CF/MD/SD/MMC/MS/MS_Pro/MS_Duo/xD/SMC compatible flash card Support SD1.1/SD2.0 Support MMC4.1. MMC4.2. Support CF4.0 DMA mode. Compliant to xD 1.2 spec. Hardware DMA engine integrated for performance enhancement. Work with default driver from Windows ME/2000/XP/Vista and Mac OS X; Windows 98/2000(SP1/SP2) and Mac OS 9 are supported by vendor driver from Alcor. Ping-pong FIFO implementation for concurrent bus operation Support multiple sectors transfer optimize performance Support slot-to-slot read/write operation Support Dynamic Icon Utility Support LED for bus operating indication Power switch integrated to reduce production BOM cost 30MHz 8051 CPU Built in 3.3V to 1.8V regulator Runs at 12MHz crystal Available in 100-pin LQFP package AU6376-GEL USB2.0 Multi-LUN Flash Memory Card Reader V1.01W 1 2. Application Block Diagram Following application diagram demonstrates a typical card reader using the AU6376 chip. By connecting the card reader to a desktop or notebook PC through USB bus, the AU6376 becomes a bus-powered, high speed USB card reader, which can be used as a bridge for data transfer between Desktop PC and Notebook PC. Figure 2.1 Block Diagram Digital Camera MP3 Player PC with USB Host Controller PDA CF/MS/MD/SMC/ xD/SD/MMC AU6376-GEL Moble Phones PC 2 AU6376-GEL USB2.0 Multi-LUN Flash Memory Card Reader V1.01W 3. Pin Assignment AU6376-GEL is available in 100-pin LQFP package. Below diagram shows signal name of each pin and table in the following page describes each pin in detail. Figure 3.1 AU6376-GEL Pin Assignment Diagram SD0DATA3 SD0DATA4 SD0DATA2 SD0DATA5 SD0DATA6 SD0DATA7 SD0DATA0 SD0DATA1 CFDATA12 CFDATA11 CFDATA13 CFDATA14 CFDMAEN SMDATA4 CFDATA5 CFDATA3 CFDATA4 CFDATA6 100 LUNSEL0 CFDATA10 XDCEN CFDATA9 SMCLE CFDATA2 SMRDN CFDATA8 SMALE CFDATA1 SMRBN CFDATA0 SMWRN CFAD0 XDWPN CFDMACKN CFAD1 REXT VD33P DP DM VS33P XI XO VSSU 25 26 V18 VDDHM VSSHM VDD MSBS MSDATA1 SMDATA0 MSDATA0 SMDATA7 MSDATA2 SMDATA1 MSINS SMDATA6 MSDATA3 SMDATA2 MSCLK CFDMARQ CARDLED CFPWRLED NC NC NC NC NC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 AU6376-GEL USB2.0 Multi-LUN Flash Memory Card Reader V1.01W LUNSEL1 SD0CMD SD0CLK SMCDN XDCDN CFCDN RFU 76 75 74 73 72 71 70 69 68 67 66 VSSHM VDDHM CHIPRESETN SMDATA3 CFDATA7 SMDATA5 CFDATA15 SD0CDN CFCE1N SD0WP CFCE2N CFRDN CFWRN XDCISN CFRESETN RFU CFWTN DECV CFAD2 EEPDATA EEPCLK SD_V33 MS_V33 51 50 VDD33C XD_V33 CF_V33 Alcor Micro AU6376-GEL 100-PIN LQFP 65 64 63 62 61 60 59 58 57 56 55 54 53 52 3 Table 3.1 AU6376-GEL Pin Descriptions Pin # Pin Name I/O Description LUN mode select, (LUNSEL1, LUNSEL0)= (0,0): 4LUN (0,1): 1LUN (1,0): 2LUN (CF, others) (1,1): 2LUN (Others, Flash) CF Data10 XD CEN CF Data9 SMC CLE CF Data2 SMC RDN CF Data8 SMC ALE CF Data1 SMC RBN CF Data0 SMC RBN CF Address0 XD WPN CF DMA ACK. Low active. CF Address1 External Resistor 330 to Ground 3.3V Power Source for UTMI DP DM Ground Power 12MHz Crystal Input 12MHz Crystal Output Ground 1.8V Core Power 3.3V Power Source for IO pad 1 LUNSEL0 I 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 4 CFDATA10 XDCEN CFDATA9 SMCLE CFDATA2 SMRDN CFDATA8 SMALE CFDATA1 SMRBN CFDATA0 SMWRN CFAD0 XDWPN CFDMACKN CFAD1 REXT VD33P DP DM VS33P XI XO VSSU V18 VDDHM IO O IO O IO O IO O IO I IO O O IO O O IO PWR IO IO GND I O GND O PWR AU6376-GEL USB2.0 Multi-LUN Flash Memory Card Reader V1.01W Pin # 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 Pin Name VSSHM VDD MSBS MSDATA1 SMDATA0 MSDATA0 SMDATA7 MSDATA2 SMDATA1 MSINS SMDATA6 MSDATA3 SMDATA2 MSCLK CFDMARQ CARDLED CFPWRLED NC NC NC NC NC VDD33C CF_V33 XD_V33 MS_V33 SD_V33 EEPCLK EEPDATA CFAD2 DECV I/O GND PWR O IO IO IO IO IO IO I IO IO IO O I O O Description 3.3V ground for IO pad Core Power 1.8V Input MS BS MS Data1 xD/SMC Data0 MS Data0 xD/SMC Data7 MS Data2 xD/SMC Data1 MS Card Detect (“0”:Detected; “1”:Undetected) xD/SMC Data6 MS Data3 xD/SMC Data2 MS CLK CF DMA request. Card access LED. CF power LED PWR PWR PWR PWR PWR O IO O I 3.3V power for PMOS CF Power XD Power MS Power SD Power EEPCLK EEPDATA CF Address2 USB current value.("1":250mA for WHQL; "0":100mA for normal mode) 5 AU6376-GEL USB2.0 Multi-LUN Flash Memory Card Reader V1.01W Pin # 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 6 Pin Name CFWTN RFU CFRESETN XDCISN CFWRN CFRDN CFCE2N SD0WP CFCE1N SD0CDN CFDATA15 SMDATA5 CFDATA7 SMDATA3 CHIPRESETN VDDHM VSSHM SD0DATA1 SD0DATA0 CFDATA14 SD0DATA7 SD0DATA6 CFDATA6 SD0CLK CFDATA13 SD0DATA5 SD0CMD CFDATA5 SD0DATA4 CFDATA12 SD0DATA3 CFDATA4 I/O I I O I O O O I O I IO IO IO IO I PWR GND IO IO IO IO IO IO O IO IO IO IO IO IO IO IO SD0 Write Protect CF WRN CF RDN CF Reset CF WTN Description SD0 Card Detect (“0”:Detected; “1”:Undetected) CF Data15 xD/SMC Data5 CF Data7 xD/SMC Data3 Chip Reset 3.3V Power Source for IO pad 3.3V ground for IO pad SD/MMC Data1 SD/MMC Data0 CF Data14 SD/MMC Data7 SD/MMC Data6 CF Data6 SD0 CLK CF Data13 SD/MMC Data5 SD0 CMD CF Data5 SD/MMC Data4 CF Data12 SD/MMC Data3 CF Data4 AU6376-GEL USB2.0 Multi-LUN Flash Memory Card Reader V1.01W Pin # 91 92 93 94 95 96 97 98 99 Pin Name SD0DATA2 CFDATA11 SMDATA4 CFDATA3 SMCDN CFCDN XDCDN RFU CFDMAEN I/O IO IO IO IO I I I I I SD/MMC Data3 CF Data11 xD/SMC Data4 CF Data3 Description SMC Card Detect (“0”:Detected; “1”:Undetected) CF Card Detect (“0”:Detected; “1”:Undetected) XD Card Detect (“0”:Detected; “1”:Undetected) NC CF DMA mode enable '0' for disable. '1' for enable. [Default] '1' LUN mode select, (LUNSEL1, LUNSEL0)= (0,0): 4LUN (0,1): 1LUN (1,0): 2LUN (CF, others) (1,1): 2LUN (Others, Flash) 100 LUNSEL1 I AU6376-GEL USB2.0 Multi-LUN Flash Memory Card Reader V1.01W 7 4. System Architecture and Reference Design 4.1 AU6376 Block Diagram Figure 4.1 AU6376 Block Diagram USB USB Upstream Port XCVR SIE RAM CF/MD/SMC/ SD/MMC/MS/ xD Control FIFO SD MMC CF XD SMC MD MS 1.8 V Processor ROM Arbitrator 1.8V Voltage Regulator /Power Switch 3.3V 12MHz XTAL 8 AU6376-GEL USB2.0 Multi-LUN Flash Memory Card Reader V1.01W 5. Electrical Characteristics 5.1 Absolute Maximum Ratings Table 5.1 Absolute Maximum Ratings SYMBOL VDDHM VIN TSTG PARAMETER Power Supply Input Signal Voltage Storage Temperature RATING -0.3 to 3.6 -0.3 to VDDH +0.3 -40 to 150 UNITS V V O C 5.2 Recommended Operating Conditions Table 5.2 Recommended Operating Conditions SYMBOL VDDH VDD V18 VIN TOPR PARAMETER Power Supply Digital Supply Input Signal Voltage Operating Temperature MIN 3.0 1.62 0 0 TYP 3.3 1.8 3.3 MAX 3.6 1.98 3.6 85 UNITS V V V O C 5.3 General DC Characteristics Table 5.3 General DC Characteristics SYMBOL IIN IOZ CIN COUT CBID PARAMETER Input current Tri-state leakage current Input capacitance Output capacitance Bi-directional buffer capacitance CONDITIONS No pull-up or pull-down MIN -10 -10 TYP ±1 ±1 2.8 2.8 2.8 MAX 10 10 UNITS µA µA ρF ρF ρF Pad Limit Pad Limit Pad Limit AU6376-GEL USB2.0 Multi-LUN Flash Memory Card Reader V1.01W 9 5.4 DC Electrical Characteristics of 3.3V I/O Cells Table 5.4 DC Electrical Characteristics of 3.3V I/O Cells SYMBOL VDDH Vil Vih Vol Voh Rpu Rpd Iin Ioz PARAMETER Power supply Input low voltage CONDITIONS 3.3V I/O Limits MIN 3.0 TYP 3.3 MAX 3.6 0.8 UNIT V V V LVTTL Input high voltage Output low voltage Output high voltage Input pull-up resistance ∣Iol∣=2~16mA ∣Ioh∣=2~16mA PU=high, PD=low 2.4 55 40 -10 -10 75 75 ±1 ±1 110 150 10 10 2.0 0.4 V V KΩ KΩ μA μA Input pull-down resistance PU=low, PD=high Input leakage current Tri-state output leakage current Vin= VDDH or 0 5.5 USB Transceiver Characteristics Table 5.5 Electrical characteristics Symbol VD33P VDD V18 ICC Parameter Analog supply Voltage Digital supply Voltage Operating supply current Conditions Min. 3.0 1.62 Typ. 3.3 1.8 Max. Unit 3.6 1.98 55 V V mA High speed operating at 480 MHz 10 AU6376-GEL USB2.0 Multi-LUN Flash Memory Card Reader V1.01W Table 5.6 Static characteristic：Digital pin Symbol Parameter Conditions Input levels VIL VIH Low-level input voltage High-level input voltage Output levels VOL VOH Low-level output voltage High-level output voltage VDDH-0.2 0.2 V V 2.0 0.8 V V Min. Typ. Max. Unit Table 5.7 Static characteristic：Analog I/O pins（DP/DM） Symbol Parameter Conditions Min. Typ. Max. Unit USB2.0 Transceiver（HS） Input Levels（differential receiver） ∣VI（DP）-VI（DM）∣ High speed differential measured at the 300 input sensitivity connection as application circuit High speed data signaling common mode voltage -50 range High speed squelch detection threshold High speed disconnection detection threshold Squelch detected No squelch detected Disconnection detected Disconnection not detected Output Levels 150 625 525 VHSDIFF mV VHSCM 500 100 mV mV mV mV mV VHSSQ VHSDSC VHSOI VHSOL VHSOH VCHIRPJ VCHIRPK High speed idle level output voltage(differential) High speed low level output voltage(differential) High speed high level output voltage(differential) Chirp-J output voltage （differential） Chirp-K output voltage （differential） Resistance Equivalent resistance Driver output impedance used as internal chip only -10 -10 -360 700 -900 10 10 400 1100 -500 mV mV mV mV mV RDRV 3 6 9 Ω AU6376-GEL USB2.0 Multi-LUN Flash Memory Card Reader V1.01W 11 Overall resistance including external resistor Termination VTERM 40.5 45 49.5 VDI VCM VSE VOL VOH Termination voltage for pull-up resistor on pin 3.0 RPU USB1.1 Transceiver（FS） Input Levels（differential receiver） Differential input ∣VI（DP）-VI（DM）∣ 0.2 sensitivity Differential common 0.8 mode voltage Input Levels（single-ended receivers） Single ended receiver 0.8 threshold Output levels Low-level output voltage High-level output voltage 0 2.8 3.6 V V 2.5 V 2.0 0.3 3.6 V V V Table 5.8 Dynamic characteristic：Analog I/O pins（DP/DM） Symbol Parameter Conditions Driver Characteristics High-Speed Mode tHSR tHSF High-speed differential rise time High-speed differential fall time Full-Speed Mode tFR tFF tFRMA CL=50pF；10 to 90﹪ of∣VOH-VOL∣； CL=50pF；90 to 10﹪ Fall time of∣VOH-VOL∣； Excluding the first Differential rise/fall time transition from idle matching（tFR / tFF） mode Excluding the first Output signal crossover transition from idle voltage mode Rise time 4 4 90 20 20 110 ns ns ％ 500 500 ps ps Min. Typ. Max. Unit VCRS 1.3 2.0 V 12 AU6376-GEL USB2.0 Multi-LUN Flash Memory Card Reader V1.01W 5.6 Power Switch Feature Figure 5.1 Built-in card power switch I-V curve 1ms to 10ms ( Depend Load Capacitor ) 3.3V+/- 0.3V CARD_POWER 100ms + System Polling timing CARD_DETECT Figure 5.2 Card Detect Power-in Timing AU6376-GEL USB2.0 Multi-LUN Flash Memory Card Reader V1.01W 13 6. Mechanical Information Figure 6.1 Mechanical Information Diagram 14 AU6376-GEL USB2.0 Multi-LUN Flash Memory Card Reader V1.01W 7. Abbreviations In this chapter some of the terms and abbreviations used throughout the technical reference manual are listed as follows. SIE CF MD SMC MS SD MMC UTMI Serial Interface Engine Compact Flash Micro Drive SmartMedia Card Memory Stick Secure Digital Multimedia Card USB Transceiver Macrocell Interface About Alcor Micro, Corp. Alcor Micro, Corp. designs, develops and markets highly integrated and advanced peripheral semiconductor, and software driver solutions for the personal computer and consumer electronics markets worldwide. We specialize in USB solutions and focus on emerging technology such as USB and IEEE 1394. The company offers a range of semiconductors including controllers for USB hub, integrated keyboard/USB hub and USB Flash memory card reader…etc. Alcor Micro, Corp. is based in Taipei, Taiwan, with sales offices in Taipei, Japan, Korea and California. Alcor Micro is distinguished by its ability to provide innovative solutions for spec-driven products. Innovations like single chip solutions for traditional multiple chip products and on-board voltage regulators enable the company to provide cost-efficiency solutions for the computer peripheral device OEM customers worldwide. AU6376-GEL USB2.0 Multi-LUN Flash Memory Card Reader V1.01W 15