19-237/R6G7Y5C-A01/2T

EVERLIGHT ELECTRONICS CO.,LTD. Technical Data Sheet (Preliminary) Full Color Chip LED 19-237/R6G7Y5C-A01/2T Features ․Package in 8mm tape on 7〞diameter reel. ․Compatible with automatic placement equipment. ․Compatible with infrared and vapor phase reflow solder process. ․Multi-color type. ․Pb-free. ․The product itself will remain within RoHS compliant version. Descriptions ․The 19-237 SMD Taping is much smaller than lead frame type components, thus enable smaller board size, higher packing density, reduced storage space and finally smaller equipment to be obtained. ․Besides, lightweight makes them ideal for miniature applications. etc. Applications ․Backlighting in dashboard and switch. ․Telecommunication: indicator and backlighting in telephone and fax. ․Flat backlight for LCD, switch and symbol. ․General use. Device Selection Guide Chip Type Material Emitted Color R6 AlGaInP Brilliant Red G7 AlGaInP Brilliant Yellow Green Y5 AlGaInP Brilliant Yellow Resin Color Water Clear Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1.1 Page: 1 of 12 Device No. : DSE-937 Prepared date: 04-Oct-2006 Prepared by :Esther Yan EVERLIGHT ELECTRONICS CO.,LTD. 19-237/R6G7Y5C-A01/2T Package Outline Dimensions Yellow Green 1.6 Yellow 3 1 4 1.6 2 Anode mark Red 1.1 0.35 1.0 0.8 For reflow soldering (propose) 2 3 0.55 0.55 0.35 0.55 4 0.55 1 0.8 2.4 Note: The tolerances unless mentioned is ±0.1mm,Unit = mm Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1.1 Page: 2 of 12 Device No. : DSE-937 Prepared date: 04-Oct-2006 Prepared by :Esther Yan EVERLIGHT ELECTRONICS CO.,LTD. 19-237/R6G7Y5C-A01/2T Absolute Maximum Ratings (Ta=25℃) Parameter Symbol Rating Unit Reverse Voltage VR 5 V R6:25 Forward Current IF mA G7:25 Y5:25 Peak Forward Current (Duty 1/10 @1KHz) R6:60 IFP mA G7:60 Y5:60 R6:60 Power Dissipation Pd mW G7:60 Y5:60 Electrostatic Discharge(HBM) ESD 2000 V Operating Temperature Topr -40 ~ +85 ℃ Storage Temperature Tstg -40 ~ +90 ℃ Soldering Temperature Tsol Reflow Soldering : 260 ℃ for 10 sec. Hand Soldering : 350 ℃ for 3 sec. Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1.1 Page: 3 of 12 Device No. : DSE-937 Prepared date: 04-Oct-2006 Prepared by :Esther Yan EVERLIGHT ELECTRONICS CO.,LTD. 19-237/R6G7Y5C-A01/2T Electro-Optical Characteristics (Ta=25℃) Parameter Luminous Intensity Viewing Angle Symbol Iv Min. Typ. R6 57.0 90.0 G7 28.5 45.0 Y5 36.0 57.0 ----- 120 2θ1/2 Dominant Wavelength Spectrum Radiation Bandwidth λp λd G7 ----- 591 R6 624 ----- 589 R6 20 ----- VF ----- deg ----- nm ----- nm ----- nm 20 R6 1.7 2.0 2.4 G7 1.7 2.0 2.4 Y5 1.7 2.0 2.4 IR G7 IF=20mA V 10 R6 Reverse Current Condition 15 Y5 Forward Voltage mcd 573 Y5 △λ G7 ----- 575 Y5 G7 Unit 632 R6 Peak Wavelength Max. ----- ----- 10 μA VR=5V 10 Y5 Notes: 1.Tolerance of Luminous Intensity ±11% Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1.1 Page: 4 of 12 Device No. : DSE-937 Prepared date: 04-Oct-2006 Prepared by :Esther Yan EVERLIGHT ELECTRONICS CO.,LTD. 19-237/R6G7Y5C-A01/2T Typical Electro-Optical Characteristics Curves R6 Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1.1 Page: 5 of 12 Device No. : DSE-937 Prepared date: 04-Oct-2006 Prepared by :Esther Yan EVERLIGHT ELECTRONICS CO.,LTD. 19-237/R6G7Y5C-A01/2T Typical Electro-Optical Characteristics Curves G7 Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1.1 Page: 6 of 12 Device No. : DSE-937 Prepared date: 04-Oct-2006 Prepared by :Esther Yan EVERLIGHT ELECTRONICS CO.,LTD. 19-237/R6G7Y5C-A01/2T Typical Electro-Optical Characteristics Curves Y5 Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1.1 Page: 7 of 12 Device No. : DSE-937 Prepared date: 04-Oct-2006 Prepared by :Esther Yan EVERLIGHT ELECTRONICS CO.,LTD. 19-237/R6G7Y5C-A01/2T Label explanation CAT: Luminous Intensity Rank HUE: Dom. Wavelength Rank REF: Forward Voltage Rank Reel Dimensions Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1.1 Page: 8 of 12 Device No. : DSE-937 Prepared date: 04-Oct-2006 Prepared by :Esther Yan EVERLIGHT ELECTRONICS CO.,LTD. 19-237/R6G7Y5C-A01/2T Carrier Tape Dimensions: Loaded quantity 2000 PCS per reel Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Moisture Resistant Packaging Label Aluminum moisture-proof bag Desiccant Label Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1.1 Page: 9 of 12 Device No. : DSE-937 Prepared date: 04-Oct-2006 Prepared by :Esther Yan EVERLIGHT ELECTRONICS CO.,LTD. 19-237/R6G7Y5C-A01/2T Reliability Test Items And Conditions The reliability of products shall be satisfied with items listed below. Confidence level：90% LTPD：10% Test Sample Hours/Cycles Size No. Items Test Condition 1 Reflow Soldering Temp. : 260℃±5℃ Min. 5sec. 6 Min. 22 PCS. 0/1 Temperature Cycle H : +100℃ 15min ∫ 5 min L : -40℃ 15min 300 Cycles 22 PCS. 0/1 Thermal Shock H : +100℃ 5min ∫ 10 sec L : -10℃ 5min 300 Cycles 22 PCS. 0/1 Temp. : 100℃ 1000 Hrs. 22 PCS. 0/1 Temp. : -40℃ 1000 Hrs. 22 PCS. 0/1 2 3 4 5 High Temperature Storage Low Temperature Storage Ac/Re 6 DC Operating Life IF = 20 mA 1000 Hrs. 22 PCS. 0/1 7 High Temperature / High Humidity 85℃/ 85%RH 1000 Hrs. 22 PCS. 0/1 Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1.1 Page: 10 of 12 Device No. : DSE-937 Prepared date: 04-Oct-2006 Prepared by :Esther Yan EVERLIGHT ELECTRONICS CO.,LTD. 19-237/R6G7Y5C-A01/2T Precautions For Use 1. Over-current-proof Customer must apply resistors for protection, otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package: The LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 After opening the package: The LED's floor life is 1 year under 30℃ or less and 60% RH or less. If unused LEDs remain, it should be stored in moisture proof packages. 2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5℃ for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1.1 Page: 11 of 12 Device No. : DSE-937 Prepared date: 04-Oct-2006 Prepared by :Esther Yan EVERLIGHT ELECTRONICS CO.,LTD. 19-237/R6G7Y5C-A01/2T 4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. EVERLIGHT ELECTRONICS CO., LTD. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Tucheng, Taipei 236, Taiwan, R.O.C Tel: 886-2-2267-2000, 2267-9936 Fax: 886-2267-6244, 2267-6189, 2267-6306 http://www.everlight.com Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1.1 Page: 12 of 12 Device No. : DSE-937 Prepared date: 04-Oct-2006 Prepared by :Esther Yan