67-21-S2C-FQ2R2B-2T

EVERLIGHT ELECTRONICS CO.,LTD. Technical Data Sheet TOP Views LEDs 67-21/S2C-FQ2R2B/2T Features ․P-LCC-2 package. ․White package. ․Optical indicator. ․Colorless clear window. ․Wide viewing angle. ․Suitable for vapor-phase reflow, Infrared reflow and wave solder processes. ․Computable with automatic placement equipment. ․Available on tape and reel (8mm Tape). ․Pb-free Descriptions ․The 67-21 series is available in soft orange, green,blue and yellow. Due to the package design, the LED has wide viewing angle and optimized light coupling by inter reflector. This feature makes it ideal for light pipe application. The low current requirement makes this device ideal for portable equipment or any other application where power is at a premium. Applications ․Automotive: backlighting in dashboard and switch. ․Telecommunication: indicator and backlighting in telephone and fax. ․Flat backlight for LCD, switch and symbol. ․Light pipe application. ․General use. Device Selection Guide Chip Lens Color Material AlGaInP Emitted Color Brilliant Orange Water Clear Everlight Electronics Co., Ltd. Device No. : DSE-671-244 http://www.everlight.com prepared date:12-17-2004 Rev. 1 Page: 1 of 10 Prepared by: Bennett EVERLIGHT ELECTRONICS CO.,LTD. 67-21/S2C-FQ2R2B/2T Package Dimensions Note: The tolerances unless mentioned is ±0.1mm Unit = mm Everlight Electronics Co., Ltd. Device No. : DSE-671-244 http://www.everlight.com prepared date:12-17-2004 Rev. 1 Page: 2 of 10 Prepared by: Bennett EVERLIGHT ELECTRONICS CO.,LTD. 67-21/S2C-FQ2R2B/2T Absolute Maximum Ratings (Ta=25℃) Parameter Reverse Voltage Forward Current Operating Temperature Storage Temperature Soldering Temperature Electrostatic Discharge Power Dissipation Peak Forward Current(Duty 1/10 @ 1KHz) Symbol VR IF Topr Tstg Tsol ESD Pd IFP Rating 5 50 -40 ~ +85 -40~ +100 260 (for 5 second) 2000 120 100 Unit V mA ℃ ℃ ℃ V mW mA Electro-Optical Characteristics (Ta=25℃) Parameter Luminous Intensity Viewing Angle Peak Wavelength Dominant Wavelength Spectrum Radiation Bandwidth Forward Voltage Reverse Current Symbol IV 2θ1/2 λp λd △λ VF IR Min. 90 --------603 ----1.75 ----- Typ. ----120 611 ----17 2.0 ----- Max. 180 --------609 ----2.35 10 Unit mcd deg nm nm nm V μA Condition IF=20mA IF=20mA IF=20mA IF=20mA IF=20mA IF=20mA VR=5V Notes: 1.Tolerance of Luminous Intensity ±10% 2.Tolerance of Dominant Wavelength ±1nm 3.Tolerance of Forward Voltage ±0.1V Everlight Electronics Co., Ltd. Device No. : DSE-671-244 http://www.everlight.com prepared date:12-17-2004 Rev. 1 Page: 3 of 10 Prepared by: Bennett EVERLIGHT ELECTRONICS CO.,LTD. 67-21/S2C-FQ2R2B/2T Bin Range Of Dominant Wavelength Group Bin Code EE1 EE2 Min. 603 606 Max. 606 609 Max Unit nm Condition IF=20mA F Bin Rang Of Luminous Intensity Bin Min Unit mcd Condition IF=20mA Q2 R1 R2 90 112 140 112 140 180 Bin Rang Of Forward Voltage Group Bin 0 1 B 2 Notes: Min 1.75 1.95 2.15 Max 1.95 2.15 2.35 Unit V Condition IF=20mA 1.Tolerance of Luminous Intensity ±10% 2.Tolerance of Dominant Wavelength ±1nm 3.Tolerance of Forward Voltage ±0.1V Everlight Electronics Co., Ltd. Device No. : DSE-671-244 http://www.everlight.com prepared date:12-17-2004 Rev. 1 Page: 4 of 10 Prepared by: Bennett EVERLIGHT ELECTRONICS CO.,LTD. 67-21/S2C-FQ2R2B/2T Typical Electro-Optical Characteristics Curves Everlight Electronics Co., Ltd. Device No. : DSE-671-244 http://www.everlight.com prepared date:12-17-2004 Rev. 1 Page: 5 of 10 Prepared by: Bennett EVERLIGHT ELECTRONICS CO.,LTD. 67-21/S2C-FQ2R2B/2T Label explanation CAT: Luminous Intensity Rank HUE: Dom. Wavelength Rank REF: Forward Voltage Rank Reel Dimensions Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Everlight Electronics Co., Ltd. Device No. : DSE-671-244 http://www.everlight.com prepared date:12-17-2004 Rev. 1 Page: 6 of 10 Prepared by: Bennett EVERLIGHT ELECTRONICS CO.,LTD. 67-21/S2C-FQ2R2B/2T Carrier Tape Dimensions: Loaded quantity 2000 PCS per reel. Note: The tolerances unless mentioned is ±0.1mm Unit = mm Moisture Resistant Packaging Label Aluminum moistue-proof bag Desiccant Label Everlight Electronics Co., Ltd. Device No. : DSE-671-244 http://www.everlight.com prepared date:12-17-2004 Rev. 1 Page: 7 of 10 Prepared by: Bennett EVERLIGHT ELECTRONICS CO.,LTD. 67-21/S2C-FQ2R2B/2T Reliability Test Items And Conditions The reliability of products shall be satisfied with items listed below. Confidence level：90% LTPD：10% No. 1 Items Reflow Soldering Test Condition Temp. : 260℃±5℃ Min. 5sec. H : +100℃ 15min ∫ 5 min L : -40℃ 15min H : +100℃ 5min ∫ 10 sec L : -10℃ 5min Temp. : 100℃ Temp. : -40℃ IF = 20 mA 85℃/ 85%RH Test Sample Hours/Cycles Size 6 Min. 300 Cycles 22 PCS. Ac/Re 0/1 2 Temperature Cycle 22 PCS. 0/1 3 Thermal Shock High Temperature Storage Low Temperature Storage DC Operating Life High Temperature / High Humidity 300 Cycles 1000 Hrs. 1000 Hrs. 1000 Hrs. 1000 Hrs. 22 PCS. 0/1 4 5 6 7 22 PCS. 22 PCS. 22 PCS. 22 PCS. 0/1 0/1 0/1 0/1 Everlight Electronics Co., Ltd. Device No. : DSE-671-244 http://www.everlight.com prepared date:12-17-2004 Rev. 1 Page: 8 of 10 Prepared by: Bennett EVERLIGHT ELECTRONICS CO.,LTD. 67-21/S2C-FQ2R2B/2T Precautions For Use 1. Over-current-proof Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 The LEDs should be used within a year. 2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less. 2.5 The LEDs should be used within 168 hours (7 days) after opening the package. 2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5℃ for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. Everlight Electronics Co., Ltd. Device No. : DSE-671-244 http://www.everlight.com prepared date:12-17-2004 Rev. 1 Page: 9 of 10 Prepared by: Bennett EVERLIGHT ELECTRONICS CO.,LTD. 67-21/S2C-FQ2R2B/2T 4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 280℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. EVERLIGHT ELECTRONICS CO., LTD. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Tucheng, Taipei 236, Taiwan, R.O.C Tel: 886-2-2267-2000, 2267-9936 Fax: 886-2267-6244, 2267-6189, 2267-6306 http://www.everlight.com Everlight Electronics Co., Ltd. Device No. : DSE-671-244 http://www.everlight.com prepared date:12-17-2004 Rev. 1 Page: 10 of 10 Prepared by: Bennett