1N4007GP

1N4001GP THRU 1N4007GP GLASS PASSIVATED JUNCTION RECTIFIER Reverse Voltage - 50 to 1000 Volts D * DO-204AL Forward Current - 1.0 Ampere FEATURES ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ High temperature metallurgically bonded construction ♦ Glass passivated cavity-free junction ♦ Capable of meeting environmental standards of MIL-S-19500 ♦ 1.0 Ampere operation at TA=75°C with no thermal runaway ♦ Typical IR less than 0.1µA ♦ High temperature soldering guaranteed: 350°C/10 seconds, 0.375" (9.5mm) lead length, 5 lbs. (2.3kg) tension N T E P A T 1.0 (25.4) MIN. 0.107 (2.7) 0.080 (2.0) DIA. E 0.205 (5.2) 0.160 (4.1) 1.0 (25.4) MIN. 0.034 (0.86) 0.028 (0.71) DIA. NOTE: Lead diameter is 0.026 (0.66) 0.023 (0.58) for suffix "E" part numbers MECHANICAL DATA Case: JEDEC DO-204AL molded plastic over glass body Terminals: Plated axial leads, solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Mounting Position: Any Weight: 0.012 ounce, 0.3 gram Dimensions in inches and (millimeters) *Glass-plastic encapsulation technique is covered by Patent No. 3,996,602 and brazed-lead assembly by Patent No. 3,930,306 ® MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS 1N 1N 4001GP 4002GP 1N 4003GP 1N 4004GP 1N 1N 4005GP 4006GP 1N 4007GP UNITS * Maximum repetitive peak reverse voltage * Maximum RMS voltage * Maximum DC blocking voltage * Maximum average forward rectified current 0.375" (9.5mm) lead length at TA=75°C * Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) Maximum instantaneous forward voltage at 1.0A * Maximum full load reverse current, full cycle average 0.375" (9.5mm) lead length TA= 75°C * Maximum DC reverse current at rated DC blocking voltage Typical reverse recovery time (NOTE 1) Typical junction capacitance (NOTE 2) Typical thermal resistance (NOTE 3) * Operating junction and storage temperature range TA=25°C TA=125°C VRRM VRMS VDC I(AV) 50 35 50 100 70 100 200 140 200 400 280 400 1.0 600 420 600 800 560 800 1000 700 1000 Volts Volts Volts Amp IFSM VF IR(AV) IR trr CJ RΘJA RΘJL TJ, TSTG 30.0 1.1 30.0 5.0 50.0 2.0 8.0 55.0 25.0 -65 to +175 Amps Volts µA µA µs pF °C/W °C NOTES: (1) Reverse recovery test conditions: IF=0.5A, IR=1.0A, Irr= 0.25A (2) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts (3) Thermal resistance from junction to ambient at 0.375" (9.5mm) lead length, P.C.B. mounted *JEDEC registered values 4/98 RATINGS AND CHARACTERISTIC CURVES 1N4001GP THRU 1N4007GP FIG. 1 - FORWARD CURRENT DERATING CURVE AVERAGE FORWARD RECTIFIED CURRENT, AMPERES 1.0 FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 0.8 PEAK FORWARD SURGE CURRENT, AMPERES 60 HZ RESISTIVE OR INDUCTIVE LOAD 30 25 20 TJ=TJ max. 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) 0.6 0.4 15 10 5.0 0.2 0.375” (9.5mm) LEAD LENGTH 0 0 25 50 75 100 125 150 175 AMBIENT TEMPERATURE, °C 1 10 NUMBER OF CYCLES AT 60 HZ 100 FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS INSTANTANEOUS FORWARD CURRENT, AMPERES INSTANTANEOUS REVERSE CURRENT, MICROAMPERES FIG. 4 - TYPICAL REVERSE CHARACTERISTICS 20 10 10 TJ=100°C 1 1 TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE 0.1 TJ=25°C 0.1 0.01 0 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE, % 0.01 0.6 0.8 1.0 1.2 1.4 1.6 INSTANTANEOUS FORWARD VOLTAGE, VOLTS FIG. 6 - TYPICAL TRANSIENT THERMAL IMPEDANCE TRANSIENT THERMAL IMPEDANCE (°C/W) 100 FIG. 5 - TYPICAL JUNCTION CAPACITANCE 20 JUNCTION CAPACITANCE, pF TJ=25°C f=1.0 MHZ Vsig=50mVp-p 10 10 1 0.1 0.01 0.1 1 10 100 1 0.1 t, PULSE DURATION, sec 1 10 100 REVERSE VOLTAGE, VOLTS