527-025LFP5

ARINC 600 Backshells 527-025 Strain Relief Backshell for Size 2 ARINC 600 Series Connectors 527-025 N F P 1 A 08 C 12 D 12 T S Basic Part No. Finish (Table II) Connector Designator (Table III) Entry Location (A, B, C, D, E, F, G, H, J, K, L) and Dash No. (Table I), 3 Entry Combinations Max 2.54 (64.5) Max 1.79 (45.5) 1.082 (27.5) 1.067 (27.1) “L” Entry “A” Entry S = Safety Wire Holes on Hex Locknuts, Omit For None Termination Style (Note 2) D = 2 Ring, T = 3 Ring 2.09 (53.1) “K” Entry 5.355 (136.0) 5.345 (135.8) “B” Entry A “D” Entry 3.770 (95.8) 3.760 (95.5) “J” Entry “E” Entry 3 Ring Term. Shown (Note 2) 5.61 (142.5) “C” Entry 2.004 (50.9) 1.994 (50.6) 1.258 (32.0) 1.248 (31.7) “H” Entry “F” Entry Cable Range Typ. B Typ. .125 (3.2) Dia 10 Places .168 (4.3) .158 (4.0) Typ. “G” Entry 1.415 (35.9) 1.405 (35.7) 2 Ring Term. Shown (Note 2) Metric dimensions (mm) are indicated in parentheses. © 2004 Glenair, Inc. CAGE Code 06324 Printed in U.S.A. GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912 www.glenair.com E-Mail: sales@glenair.com F-6 527-025 Strain Relief Backshell for Size 2 ARINC 600 Series Connectors TABLE I: CABLE ENTRY Dash No. 03 04 06 08 10 12 16 A Max .760 (19.3) .760 (19.3) .760 (19.3) .760 (19.3) .760 (19.3) .760 (19.3) 1.073 (27.3) B Max .844 (21.4) .906 (23.0) 1.093 (27.8) 1.187 (30.1) 1.281 (32.5) 1.500 (38.1) 1.719 (43.7) Cable Range Min Max .157 (4.0) .250 (6.4) .187 (4.7) .312 (7.9) .281 (7.1) .437 (11.1) .344 (8.7) .562 (14.3) .375 (9.5) .625 (15.9) .438 (11.1) .750 (19.1) .562 (14.3) .938 (23.8) Symbol B C* G* J LF M N TABLE II: FINISH OPTIONS Finish Symbol Finish Cadmium Plate/Olive Drab NC Zinc Cobalt/Dark Olive Drab Black Anodize NF Cadmium Plate/Olive Drab over Anodic Hard Coat Electroless Nickel Gold Iridite over Cadmium Plate T Cadmium Plate/Bright over over Electroless Nickel Electroless Nickel Cadmium Plate/Bright over U** Cadmium Plate/Black Electroless Nickel ZN Zinc-Nickel Alloy/Olive Drab *Anodize finish is not suitable for EMI shielding or grounding Electroless Nickel Cadmium Plate/Olive Drab over applications. to corrosion resisting steel backshells and **Applicable Electroless Nickel accessories. Consult factory for other available finishes. TABLE III: CONNECTOR DESIGNATOR ARINC 600 series connector backshells are designed to replace the insert retainer plates. Due to non-standard modifications by the connector manufacturer, the backshell may require special design alterations to mate properly. The following should be used to determine if a backshell modification is required. Prior to ordering, consult factory with connector part numbers not shown to ensure a proper fit. Connector Designator P Connector Description All Manufacturer’s Plug and Receptacle Shells, Except for Those Listed Below (Prior to ordering, consult factory with connector part numbers not listed below to ensure a proper fit.) Cannon BKAD****322 Series Plug Cannon/Radiall Environmental Plug Cannon/Boeing BACC 66 Plug Radiall/Boeing BACC66 Plug Cannon BKAC & BKAE XXX322 Series Environmental Plug P1 P2 P3 P5 P6 1. Metric dimensions (mm) are indicated in parentheses. 2. Designate Symbol “T” (3 ring termination) for termination of individual and overall braid. Designate symbol “D” (2 ring termination) for termination of individual or overall braid. 3. Material/Finish: Backshell, Nuts, Clamps, Ferrule = Al Alloy/See Table II Hardware = SST/Passivate © 2004 Glenair, Inc. CAGE Code 06324 Printed in U.S.A. GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912 www.glenair.com E-Mail: sales@glenair.com F-7 ARINC 600 Backshells