30KPA30A-B

TVS Diode Axial Leaded – 30000W > 30KPA series 30KPA Series RoHS Pb e3 Descriptions The 30KPA Series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events. Uni-directional Features Bi-directional Agency Approvals Agency Agency File Number E230531 Maximum Ratings and Thermal Characteristics (TA=25OC unless otherwise noted) Parameter Symbol Value Unit Peak Pulse Power Dissipation by 10/1000μs Test Waveform (Fig.2)(Note 1) PPPM 30 kW Steady State Power Dissipation on Infinite Heat Sink at TL=75ºC PD 8.0 W Peak Forward Surge Current, 8.3ms Single Half Sine Wave Unidirectional Only (Note 2) IFSM 400 A Operating Junction and Storage Temperature Range TJ , TSTG -55 to 175 °C Typical Thermal Resistance Junction to Lead RθJL 8.0 °C/W Typical Thermal Resistance Junction to Ambient RθJA 40 °C/W Notes: 1. Non-repetitive current pulse , per Fig. 4 and derated above TJ (initial) =25OC per Fig. 3. 2. Measured on 8.3ms single half sine wave or equivalent square wave, duty cycle=4 per minute maximum. • 30kW peak pulse capability at 10/1000μs waveform, repetition rate (duty cycles):0.01% • Glass passivated chip junction in P600 package • Fast response time: typically less than 1.0ps from 0 Volts to BV min • Excellent clamping capability • Typical failure mode is short from over-specified voltage or current • Whisker test is conducted based on JEDEC JESD201A per its table 4a and 4c • IEC-61000-4-2 ESD 30kV(Air), 30kV (Contact) • ESD protection of data lines in accordance with IEC 61000-4-2 • EFT protection of data lines in accordance with IEC 61000-4-4 • Low incremental surge resistance • Typical IR less than 2μA when VBR min>73V • High temperature to reflow soldering guaranteed: 260°C/40sec / 0.375”, (9.5mm) lead length, 5 lbs., (2.3kg) tension • VBR @ TJ= VBR@25°C x (1+αT x (TJ - 25)) (αT:Temperature Coefficient, typical value is 0.1%) • UL Recognized epoxy meeting flammability rating V-0 • Matte tin lead–free plated • Halogen free and RoHS compliant • Pb-free E3 means 2nd level interconnect is Pbfree and the terminal finish material is tin(Sn) (IPC/ JEDEC J-STD-609A.01) Applications TVS components are ideal for the protection of I/O interfaces, VCC bus and other vulnerable circuits used in telecom, computer, industrial and consumer electronic applications. Functional Diagram Additional Infomarion Datasheet Bi-directional Cathode Resources Samples Anode Uni-directional © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: BA.08/27/20 TVS Diode Axial Leaded – 30000W > 30KPA series Electrical Characteristics (T =25°C unless otherwise noted) A Part Number (Uni) Part Number (Bi) Reverse Stand off Voltage VR (Volts) Breakdown Voltage VBR (Volts) @ IT Min. Max. Test Current IT (mA) Maximum Peak Pulse Current Ipp (A) Maximum Reverse Leakage IR @VR (µ A) Maximum Clamping Voltage VC @ IPP (V) Agency Recognition 30KPA28A 30KPA28CA 28 31.28 34.41 50 606.0 5000 50.0 X 30KPA30A 30KPA30CA 30 33.51 36.86 50 548.9 5000 55.2 X 30KPA33A 30KPA33CA 33 36.90 40.59 50 517.9 5000 58.5 X 30KPA36A 30KPA36CA 36 40.20 44.22 50 490.3 5000 61.8 X 30KPA39A 30KPA39CA 39 43.60 47.96 20 450.9 2000 67.2 X 30KPA42A 30KPA42CA 42 46.90 51.59 10 420.8 1000 72.0 X 30KPA43A 30KPA43CA 43 48.00 52.80 10 415.1 1000 73.0 X 30KPA45A 30KPA45CA 45 50.30 55.33 5 391.5 250 77.4 X 30KPA48A 30KPA48CA 48 53.60 58.96 5 371.3 150 81.6 X 30KPA51A 30KPA51CA 51 57.00 62.70 5 350.7 50 86.4 X 30KPA54A 30KPA54CA 54 60.30 66.33 5 331.5 20 91.4 X 30KPA58A 30KPA58CA 58 64.80 71.28 5 327.9 20 92.4 X 30KPA60A 30KPA60CA 60 67.00 73.70 5 297.1 15 102.0 X 30KPA64A 30KPA64CA 64 71.50 78.65 5 291.3 10 104.0 X 30KPA66A 30KPA66CA 66 73.70 81.07 5 283.2 2 107.0 X X 30KPA70A 30KPA70CA 70 78.20 86.02 5 278.0 2 109.0 30KPA71A 30KPA71CA 71 79.30 87.23 5 271.7 2 111.5 X 30KPA72A 30KPA72CA 72 80.40 88.44 5 265.8 2 114.0 X 30KPA75A 30KPA75CA 75 83.80 92.18 5 253.8 2 119.4 X 30KPA78A 30KPA78CA 78 87.10 95.81 5 234.9 2 129.0 X 30KPA84A 30KPA84CA 84 93.80 103.18 5 217.7 2 139.2 X 30KPA90A 30KPA90CA 90 100.50 110.55 5 207.0 2 146.4 X 30KPA96A 30KPA96CA 96 107.20 117.92 5 194.2 2 156.0 X 30KPA102A 30KPA102CA 102 113.90 125.29 5 183.0 2 165.6 X 30KPA108A 30KPA108CA 108 120.60 132.66 5 172.9 2 175.2 X 30KPA120A 30KPA120CA 120 134.00 147.40 5 155.9 2 194.4 X 30KPA132A 30KPA132CA 132 147.40 162.14 5 142.3 2 213.0 X 30KPA144A 30KPA144CA 144 160.80 176.88 5 135.8 2 223.2 X 30KPA150A 30KPA150CA 150 167.60 184.36 5 129.8 2 233.4 X 30KPA156A 30KPA156CA 156 174.30 191.73 5 123.7 2 245.0 X 30KPA160A 30KPA160CA 160 178.70 196.57 5 120.0 2 252.6 X 30KPA168A 30KPA168CA 168 187.70 206.47 5 111.2 2 272.4 X 30KPA170A 30KPA170CA 170 189.90 208.89 5 110.2 2 275.0 X 30KPA180A 30KPA180CA 180 201.10 221.21 5 104.3 2 290.4 X 30KPA198A 30KPA198CA 198 221.20 243.32 5 94.7 2 319.8 X 30KPA216A 30KPA216CA 216 241.30 265.43 5 86.9 2 348.6 X 30KPA240A 30KPA240CA 240 268.10 294.91 5 78.3 2 387.0 X 30KPA258A 30KPA258CA 258 288.20 317.02 5 72.8 2 416.4 X 30KPA260A 30KPA260CA 260 290.40 319.44 5 72.8 2 416.0 X 30KPA270A 30KPA270CA 270 301.60 331.76 5 69.5 2 436.2 X 30KPA280A 30KPA280CA 280 312.80 344.08 5 65.3 2 464.0 X 30KPA288A 30KPA288CA 288 321.70 353.87 5 64.5 2 469.9 X 30KPA300A 30KPA300CA 300 334.00 367.40 5 62.0 2 484.0 X 30KPA320A 30KPA320CA 320 357.40 391.40 5 57.2 2 530.0 - 30KPA350A 30KPA350CA 350 391.00 428.10 5 53.4 2 567.0 - 30KPA360A 30KPA360CA 360 402.10 440.30 5 47.3 2 640.0 - For bidirectional type having VRWM of 60 volts and less, the IR limit is double. For parts without A , the VBR is ± 10% and Vc is 5% higher than with A parts, the parts without A are currently available, but not recommended for new designs. The parts with A are preferred. © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: BA.08/27/20 TVS Diode Axial Leaded – 30000W > 30KPA series I-V Curve Characteristics Bi-directional Uni-directional Ipp Vc VBR VR Vc VBR VR V IR VF IT IR IT VR VBR Vc V Ipp Ipp PPPM VR VBR VC IR VF IT IR Peak Pulse Power Dissipation -- Max power dissipation Stand-off Voltage -- Maximum voltage that can be applied to the TVS without operation Breakdown Voltage -- Maximum voltage that flows though the TVS at a specified test current (IT) Clamping Voltage -- Peak voltage measured across the TVS at a specified Ippm (peak impulse current) Reverse Leakage Current -- Current measured at VR Forward Voltage Drop for Uni-directional Ratings and Characteristic Curves (T =25°C unless otherwise noted) A Figure 1 - TVS Transients Clamping Waveform Figure 2 - Peak Pulse Power Rating Curve 1000 PPPM-Peak Pulse Power (kW) Voltage Transients Voltage or Current Voltage Across TVS Current Through TVS 100 10 1 0.000001 0.00001 0.0001 0.001 td-Pulse Width (sec.) Time © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: BA.08/27/20 TVS Diode Axial Leaded – 30000W > 30KPA series Ratings and Characteristic Curves (T =25°C unless otherwise noted) (Continued) A Figure 4 - Pulse Waveform 150 100 75 50 25 0 tr=10µsec IPPM- Peak Pulse Current, % IRSM Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage % Figure 3 - Peak Pulse Power Derating Curve 0 25 50 75 100 125 150 175 Half Value IPPM IPPM ( ) 2 50 200 0 10/1000µsec. Waveform as defined by R.E.A td 1.0 0 2.0 3.0 4.0 t-Time (ms) Figure 5 - Typical Junction Capacitance Figure 6 - Typical Transient Thermal Impedance 100 10000 Transient Thermal Impedance (°C/W) Uni-direconal V=0V Bi-direconal V=0V 1000 Cj (pF) Peak Value IPPM 100 TJ - Initial Junction Temperature (ºC) Uni-direconal V=VR 100 Bi-direconal V=VR 10 10 1 0.1 1 0 50 100 150 200 250 300 350 0.01 400 0.1 1 VBR - Reverse Breakdown Voltage (V) 10 100 1000 TP - Pulse Duration (s) Figure 7 - Maximum Non-Repetitive Peak Forward Surge Current Uni-Directional Only Figure 8 - Peak Forward Voltage Drop vs Peak Forward Current (Typical Values) 1000 100 900 800 IF - Peak Forward Current(A) IFSM - Peak Forward Surge Current (A) TJ=25°C Pulse Width(td) is defined as the point where the peak current decays to 50% of IPPM 700 600 500 400 300 200 4 stacked-die 5 stacked-die 10 1 100 0 1 10 Number of Cycles at 60 Hz 100 0.1 0.0 2.0 4.0 6.0 8.0 10.0 12.0 14.0 VF - Peak Forward Voltage(V) © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: BA.08/27/20 TVS Diode Axial Leaded – 30000W > 30KPA series Soldering Parameters Lead–free assembly Pre Heat - Temperature Min (Ts(min)) 150°C - Temperature Max (Ts(max)) 200°C - Time (min to max) (ts) 60 – 180 secs Average ramp up rate (Liquidus Temp (TA) to peak Reflow Ramp-up 3°C/second max 3°C/second max TS(max) to TA - Ramp-up Rate tp TP - Temperature (TA) (Liquidus) 217°C - Time (min to max) (ts) 60 – 150 seconds Peak Temperature (TP) 260+0/-5 °C Time within 5°C of actual peak Temperature (tp) 20 – 40 seconds Ramp-down Rate 6°C/second max Time 25°C to peak Temperature (TP) 8 minutes Max. Do not exceed 260°C TL Temperature (T) Reflow Condition tL Ts(max) Ramp-down Ts(min) ts Preheat 25˚C t 25˚C to Peak Time (t) Flow/Wave Soldering (Solder Dipping) Peak Temperature : 265OC Dipping Time : 10 seconds Soldering : 1 time Environmental Specifications Physical Specifications Weight 0.07oz., 2.5g High Temp. Storage JESD22-A103 Case P600 molded plastic body over passivated junction. HTRB JESD22-A108 Polarity Color band denotes the cathode except Bipolar. Matte Tin axial leads, solderable per JESD22-B102. Temperature Cycling JESD22-A104 H3TRB JESD22-A101 RSH JESD22-B106 Terminal Critical Zone TL to TP Dimensions D Dimensions Cathode Band (for uni-directional products only) C A A B Inches Millimeters Min Max Min A 1.000 - 25.40 Max - B 0.340 0.360 8.60 9.10 C 0.048 0.054 1.22 1.36 D 0.340 0.360 8.60 9.10 P600 © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: BA.08/27/20 TVS Diode Axial Leaded – 30000W > 30KPA series Part Numbering System Part Marking System 30KPA xxx XX X Cathode Band F (for uni-directional products only) Option Code: Blank Reel Tape -B Bulk Packaging YYWW Littelfuse Logo Trace Code Marking YY:Year Code WW: Week Code Type Code: A Uni-Directional (5% VBR Voltage Tolerance) CA Bi-Directional (5% VBR Voltage Tolerance) 30KPAXXX Product Type VR Voltage Series Code Packing Options Part Number Component Package Quantity Packaging Option Packaging Specification 30KPAxxxXX P600 800 Tape & Reel EIA STD RS-296 30KPAxxxXX-B P600 100 Bulk Littelfuse Spec. Tape and Reel Specification Off Center either side 0.028(0.7) 2.56 (65.0) 0.236 (6.0) 0.047 (1.2) 0.394+/-0.020 (10.0+/-0.5) 13.0 (330.2) 2.063+0.079/-0.039 (53.0+2.0/-1.0) Dimensions are in inches/mm 3.0 (76.2) 0.68 (17.27) 2.75 (69.85) Recess Depth Max. 0.75 (19.05) Direction of Feed Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at www.littelfuse.com/disclaimer-electronics. © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: BA.08/27/20