HMC168C8_08

HMC168C8 v02.1105 GaAs MMIC SMT DOUBLEBALANCED MIXER, 4.5 - 8 GHz Typical Applications The HMC168C8 is ideal for: • Microwave Point-to-Point Radios • 5.8 GHz ISM Band Circuits Features Conversion Loss: 8.2 dB LO to RF and IF Isolation: 34 dB Surface Mount Small Size, No DC Bias Required 9 MIXERS - DBL-BAL - SMT Functional Diagram General Description The HMC168C8 is a miniature double-balanced mixer in a non-hermetic ceramic surface mount package that can be used as an upconverter, downconverter or biphase modulator. The device is a passive diode/ balun type mixer with high dynamic range. Noise figure is essentially equal to the conversion loss. The mixer can handle larger signal levels than most active mixers due to the high third order intercept. MMIC implementation provides exceptional balance in the circuit resulting in high LO/RF and LO/IF isolations and unit-to-unit consistency. This mixer has applications where small size and surface mount compatibility are important. Electrical Specifi cations, TA = +25° C, LO Drive = +10 dBm Parameter Frequency Range, RF & LO Frequency Range, IF Conversion Loss Noise Figure (SSB) LO to RF Isolation LO to IF Isolation IP3 (Input) IP2 (Input) 1 dB Gain Compression (Input) 29 30 12 55 7 Min. Typ. 4.5 - 8.0 DC - 2 8.2 8.2 35 34 16 62 10 10 10 Max. Units GHz GHz dB dB dB dB dBm dBm dBm 9 - 42 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC168C8 v02.1105 GaAs MMIC SMT DOUBLEBALANCED MIXER, 4.5 - 8 GHz Conversion Loss 0 CONVERSION LOSS (dB) Isolation 0 -10 -5 ISOLATION (dB) -20 RF/IF LO/RF -10 -30 LO /IF LO /IF LO/RF -40 -50 -15 9 11 -20 0 1 2 3 4 5 6 7 8 9 10 11 RF FREQUENCY (GHz) -60 0 1 2 3 4 5 6 7 8 9 10 FREQUENCY (GHz) Conversion Loss vs. LO Power -5 CONVERSION LOSS (dB) Distortion and 1dB Compression vs. LO Drive Level Distortion LO Drive (dBm) RF (f1) = 6.01 GHz RF (f2) = 6.00 GHz LO = 6.5 GHz RF Level = 0 dBm IP3 (dBm) 14 16 18 19 IP2 (dBm) 59 62 65 65 1 dB Compression P1dB (dBm) 8.5 10 11 11 -7.5 -10 +15dBm +10dBm +13dBm +7 +9dBm -12.5 +10 +13 -15 0 1 2 3 4 5 6 7 8 RF FREQUENCY (GHz) +8dBm +15 9 10 11 Return Loss 0 LO RETURN LOSS (dB) -10 IF -20 RF -30 -40 0 1 2 3 4 5 6 7 8 9 10 11 FREQUENCY (GHz) S - Paremeters for the RF, LO, IF Ports are Available On-Line at www.hittite.com For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 9 - 43 MIXERS - DBL-BAL - SMT HMC168C8 v02.1105 GaAs MMIC SMT DOUBLEBALANCED MIXER, 4.5 - 8 GHz Absolute Maximum Ratings RF / IF Input LO Drive Storage Temperature Operating Temperature +13 dBm +27 dBm -65 to +150 °C -55 to +85 °C 9 MIXERS - DBL-BAL - SMT ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Outline Drawing NOTES: 1. PACKAGE BODY MATERIAL: WHITE ALUMINA 92% 2. LEAD, PACKAGE BOTTOM MATERIAL: COPPER 3. PLATING: ELECTROLYTIC GOLD 100-200 MICROINCHES, OVER ELECTROLYTIC NICKEL 100-250 MICROINCHES. 4. DIMENSIONS ARE IN INCHES [MILLIMETERS]. 5. PACKAGE LENGTH AND WIDTH DIMENSIONS DO NOT INCLUDE LID SEAL PROTRUSION .005 PER SIDE. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 9 - 44 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC168C8 v02.1105 GaAs MMIC SMT DOUBLEBALANCED MIXER, 4.5 - 8 GHz Evaluation PCB 9 MIXERS - DBL-BAL - SMT List of Materials for Evaluation PCB 102102 [1] Item J1 - J3 U1 PCB [2] Description PCB Mount SMA RF Connector HMC168C8 Mixer 107214 Evaluation Board [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 9 - 45