1462037-1

Signal Relays AXICOM IM Relay line 10x6mm, low profile 5.65mm and min. board-space 60mm2 n Switching current 2/5A, switching power 60W/62.5VA and switching voltage 220VDC/250VAC n Low coil power consumption, 140mW standard, 100mW for high sensitive version, 50mW for ultra high sensitive version and 100mW for bistable version n High dielectric and surge capability up to 2500Vrms between open contacts and 2500Vrms between coil and contacts n High mechanical shock resistance up to 50g functional n Slim IM_ Typical applications Telecommunication, access and transmission equipment, optical network terminals, modems, office and business equipment, consumer electronics, AXICOMÊSignalÊRelays measurement and test equipment, industrial control, medical equipment, IM Relay automotive applications, HVAC U 108-98001 Rev. M Contact Data (continued) Approvals Contact Data Electrical endurance at contact application 0 IM-D IM-E (≤30mV/≤10mA) min. 2.5x106 operations Number of contacts and type 1ÊPoleÊbreak 1ÊPoleÊmake 1ÊPoleÊÊ 2ÊPoleÊbreak 2ÊPoleÊmake Contact Data standard, C D, I P cable load open end min. 2.0x106 operations changeover Contact assembly BifurcatedÊcontacts standard and high high contact resistive, 125VDC / 0.24A - 30W min. 5x105 operations Contact material Palladium-ruthenium,Êgold-covered high dielectric current stability resistive, 220 VDC / 0.27A - 60W min. 1x105 operations Limiting continuous current 2ÊA 2ÊA 4ÊA resistive, 2ÊA250VAC / 2ÊA version version version 0.25A - 62.5VA min. 1x105 operations at max. ambient temperature Contact arrangement 2 form C, 2 CO resistive, 30VDC / 1A - 30W min. 5x105 operations Maximum switching current 2ÊA 2ÊA 3ÊA 2ÊA 2ÊA Max. switching voltage 220VDC, 220VDC, 220VDC, resistive, 30VDC / 2A 60W min. 1x105 operations Maximum swichting voltage 220ÊVdc UL contact rating 30VDC, 2A, 60W, NO only 250VAC 250VAC 250VAC 250ÊVac Maximum switching capacity Rated current 2A 5A 2A 110VDC, 0.3A, 33W 60ÊW,Ê62.5ÊVA Thermoelectric potential Limiting continuous current 2A 5A 2A 220VDC, 0.27A, 60W 10 Version Narrow Version IM Relay 405 Capacitance 23 500 50 Coil5 Operating4.25 Range 0.50 26 12 10.20 1.20 2880 50 between open contacts max. 1pF All figures are given for coil without pre-energization, at ambient temperature +23°C between contact and coil max. 2pF Coil Operating Range Unom Nominal coil voltage = between adjacent contacts max.10.0±0.08 2pF 5.7±0.3 3.4 50mW coil 6.0±0.08 10.0±0.08 3.2 range, sensitive and ultra high sensitive Coil operating 5.7±0.3 Umax. =10.0±0.08 Upper limit of6.0±0.08 the operative range of 10.0±0.08 100mW coilcoil 1 0.4 0.8 0.2 0.60 0.4 -50 0.2 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 Urel. min. 90 10 0 1 10 12 0 2.2±0.15 2.2±0.15 3.2±0.15 3.2 Gull W 10. Mounting Hole refer to the Product Compliance Support Center at Layout Hole Layout www.te.com/customersupport/rohssupportcenter Mounting 0.4 3.2±0.15 0.3±0.05 5.8±0.08 5.8±0.08 0.75 0.75 5.65-0.2 3.2 3.2 2.2±0.15 2.2±0.15 Urel. min. rel. min. UopUmin. 3.2±0.15 Unom. nominal coil voltage 2.2±0.15 Uop min. 2.2±0.15 Urel. min. Unom. nominal coil voltage Umax. at 2x2A 3.2±0.15 1.4 0.8 1.2 0.6 Uop. min. 2.2±0.15 2 1.4 1.8 1.2 1.61 Umax. at 0A Umax. at 0A Umax. at 2x2A 2.4 1.8 2.2 1.6 = Nominal coil voltage the coil voltage (limiting voltage) when coils are continously energized RF Data = Upper limit of the operative range of the coil voltage (limiting voltage) Isolation at 100MHz/900MHz 37.0dB/18.8dB = Lower limit of the operative rangewhen of coils arevoltage continously energized the coil (reliable operate voltage) Insertion loss at 100MHz/900MHz 0.03dB/0.33dB 0.4 Voltage wave ratio = Lower limit ofrelays the 0.4 operative Forstanding latching Uset (VSWR) min.range resp.of 0.4 coil0.4 voltage (reliable operate voltage) at the 100MHz/900MHz 1.06/1.49 3.2±0.1 Ureset min. 5.08±0.1 3.2±0.1 For latching relays Uset min.range resp. of = Lower limit of the operative 5.08±0.1 Ureset the coilmin. voltage (reliable release voltage) Other Data = Lower limit of the operative range of Material EU RoHS/ELV, China RoHS, REACH, Halogen content the compliance: coil voltage (reliable release voltage) 2.2±0.15 Umax. at 0A Umax. at 2x1A Unom Umax. Uop. min. 3.2±0.15 3 2.4 2.8 2.2 2.62 50mW Umax.coil at 0A 100mW coil 5.65-0.2 Umax. at 2x1A 3.2 Coil Voltage Coil [U/Unom] Voltage [U/Unom] 3 3.4 2.8 3.2 2.6 SMT 0.3±0.05 THT Version THT Version Copla Solder Ambient +85°C Viewtemperature onto the component side of-40°C the toPCB (top view) resistance -50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 10 0 1 10 12 0 ViewThermal onto the component side of the PCB