55FA0511-22-7L-CS2879

TITLE SPECIFICATION CONTROL DRAWING 55FA0511 Date CABLE, ELECTRIC, FILTER LINE - ELECTROLOSS, COMPONENT WIRE 7-23-10 Revision J This specification sheet forms a part of the latest issue of Raychem Specification 55F. FILTER LAYER - RADIATION-MODIFIED, ABSORPTIVE COMPOUND CONDUCTOR - TIN-COATED COPPER PRIMARY INSULATION - RADIATION-CROSSLINKED, MODIFIED PVDF COLOR - NATURAL PRIMARY JACKET - RADIATION-CROSSLINKED, MODIFIED ETFE TABLE I. CONSTRUCTION DETAILS PART NUMBER 1/ WIRE SIZE (AWG) CONDUCTOR STRANDING (number x AWG) DIAMETER OF STRANDED CONDUCTOR (in.) MINIMUM MAXIMUM FINISHED WIRE MAXIMUM RESISTANCE AT 20°C (ohms/1000 ft) 16.2 DIAMETER (in.) MAXIMUM WEIGHT (lbs/1000 ft.) 55FA0511-22-* 22 19 x 34 .029 .033 .051 ± .003 4.0 55FA0511-20-* 20 19 x 32 .037 .041 9.88 .059 ± .003 5.8 55FA0511-18-* 18 19 x 30 .046 .051 6.23 .070 ± .003 8.7 55FA0511-16-* 16 19 x 29 .052 .058 4.81 .078 ± .004 11.2 55FA0511-14-* 14 19 x 27 .065 .073 3.06 .095 ± .004 16.1 55FA0511-12-* 12 37 x 28 .084 .090 2.02 .112 ± .004 24.0 55FA0511-10-* 10 37 x 26 .106 .114 1.26 .136 ± .005 37.0 TABLE II. PERFORMANCE DETAILS BEND TESTING PART NUMBER 1/ MANDREL DIAMETER (inch) (± 3%) IMMERSION, LIFE CYCLE AND CROSSLINKING PROOF TEST WEIGHT (lb) (± 3%) COLD BEND IMMERSION, LIFE CYCLE AND CROSSLINKING PROOF TEST COLD BEND .750 3.00 55FA0511-22-* .500 2.00 55FA0511-20-* .750 2.50 1.25 4.00 55FA0511-18-* 1.00 3.00 1.75 4.00 55FA0511-16-* 1.00 3.00 2.00 5.00 55FA0511-14-* 1.00 5.00 2.00 5.00 55FA0511-12-* 1.50 6.00 2.50 5.00 55FA0511-10-* 1.50 8.00 2.50 5.00 This product meets or exceeds all requirements of SAE AS85485/9, less identification, for AWG’s 22-10. All other AWG sizes meet or exceed requirements of SAE AS85485, less identification. Users should evaluate the suitability of this product for their application. Specifications are subject to change without notice. Tyco Electronics also reserves the right to make changes in materials or processing, which do not affect compliance with any specification, without notification to Buyer. 1/ COLORS AND COLOR CODE DESIGNATORS SHALL BE IN ACCORDANCE WITH MIL-STD-681. OTHER CODES AND SUFFIXES MAY BE ADDED TO THE PART NUMBER. AS NECESSARY, TO CAPTURE ANY ADDITIONAL REQUIREMENTS IMPOSED BY THE PURCHASE ORDER. The TE logo, Tyco Electronics, Electroloss and Raychem are trademarks. Page 1 of 3 DIMENSIONS ARE IN INCHES, AND UNLESS OTHERWISE DESIGNATED ARE NOMINAL THIS SPECIFICATION SHEET TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN. REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATION FOR BID. Raychem Wire & Cable 501 Oakside Avenue Redwood City, CA 94063-3800 Phone: 1-800-227-8816 Fax: 1-650-361-6297 © 2010 Tyco Electronics Corporation. All rights reserved. SPECIFICATION CONTROL DRAWING Revision Page 2 of 3 SCD Number J WIRE RATINGS AND ADDITIONAL REQUIREMENTS TEMPERATURE RATING: 150°C Maximum continuous conductor temperature VOLTAGE RATING: 600 volts (rms) at sea level ATTENUATION (INSERTION LOSS): See Table III BLOCKING: 200 ± 3°C for 6 hours COLOR: Light violet preferred CONCENTRICITY: Primary Insulation - 50% (minimum); Finished Wire - 70% (minimum) CROSSLINKING PROOF TEST: 300 ± 3°C for 7 hours FLAMMABILITY: 3 seconds (maximum); 3 in. (maximum); no flaming of facial tissue FLUORIDE EXTRACTION: 70 ± 2°C for 168 hours, 150 ppm (maximum) HUMIDITY RESISTANCE: Insulation Resistance, 5000 meghoms for 1000 ft. (minimum) IDENTIFICATION AND COLOR STRIPING DURABILITY: 125 cycles (250 strokes) (minimum), 500 g weight IMMERSION: Diameter increase 5% (maximum); no cracking, no dielectric breakdown INSULATION ELONGATION AND TENSILE STRENGTH: Primary Insulation, Filter Layer and Primary Jacket pulled together Elongation, 50% (minimum) Tensile Strength, 3000 lbf/in2 (minimum) INSULATION FLAWS: Primary Insulation only, Spark Test, 1.5 kV (rms) at 60 Hz 4.2 kV (rms) at 3 kHz Impulse Dielectric Test, 6.0 kV (peak) Finished Wire, Spark Test, 3.0 kV (rms) at 60 Hz 5.7 kV (rms) at 3 kHz Impulse Dielectric Test, 8.0 kV (peak) INSULATION RESISTANCE: 5000 megohms for 1000 ft. (minimum) INSULATION THICKNESS: Primary Insulation, .002 in. (minimum); Filter Layer, average .0025 in. (minimum); Primary Jacket, .0035 in. (minimum) LIFE CYCLE: 200 ± 3°C for 168 hours LOW TEMPERATURE-COLD BEND: -65 ± 2°C for 4 hours SHRINKAGE: 200 ± 3°C for 6 hours, 0.125 in. (maximum) SMOKE: 200 ± 2°C, no visible smoke SURFACE RESISTANCE: 500 meghoms-in. (minimum), initial and final readings THERMAL SHOCK RESISTANCE: 150 ± 3°C, .060 in. (maximum) THERMAL STABILITY: 180 ± 3°C for 1250 hours VOLTAGE WITHSTAND (Post Environmental): 1500 volts (rms), 60 Hz WRAP TEST: 200 ± 3°C for 6 hours, no cracking PART NUMBER: The "*" in the part numbers in Tables I-III shall be replaced by a color code designator, except that violet shall be light violet and designator shall be 7L. 1/ Example: AWG 20, light violet: 55FA0511-20-7L AWG 20, light violet with blue stripe: 55FA0511-20-7L6 1/ See footer section on page 1 55FA0511 SPECIFICATION CONTROL DRAWING Revision Page 3 of 3 SCD Number J 55FA0511 100 90 80 70 60 Attenuation (dB/foot) 50 Typical curve for size 20 40 30 20 10 0 1.0 10.0 100. 1000. Frequency (MHz) ATTENUATION (INSERTION LOSS) TABLE III. ATTENUATION (INSERTION LOSS) + PART NUMBER 1/ PASS BAND (dB/ft.) 1.0 MHz TRANSITION BAND (dB/ft.) 10.0 MHz STOP BAND (dB/ft.) 100 MHz 500 MHz 1000 MHz 1 to 12 GHz (max) (min) (max) (min) (min) (min) (min) 55FA0511-22-* .02 .06 0.20 1.3 12 30 30 55FA0511-20-* .02 .06 0.20 1.3 12 30 30 55FA0511-18-* .02 .06 0.20 1.3 13 33 33 55FA0511-16-* .02 .06 0.20 1.3 13 33 33 55FA0511-14-* .02 .06 0.20 1.3 13 33 33 55FA0511-12-* .02 .04 0.20 1.3 12 30 30 55FA0511-10-* .02 .04 0.20 1.3 12 30 30 1/ See footer section on page 1 + THE PRIMARY WIRE OF THIS SPECIFICATION SHEET SHALL MEET THE ATTENUATION REQUIREMENTS SHOWN ABOVE ONLY WHEN USED AS A SINGLE COMPONENT IN A SHIELDED CABLE.