RMK6-12.7

TECHNICAL DATA SHEET RayMark Six Labels Document number: TTDS-032 Issue: 2 Date: August 2014 MATERIAL DESCRIPTION: Computer-printable zero halogen label material. Permanent pressure sensitive acrylic adhesive. Thermally stabilised white polyester film with special ink receptive latent cure epoxy coating on the label surface. After printing, the surface is heat cured, embedding the image within a tough polymeric layer. USE: RayMark Six labels have outstanding abrasion and fluid resistance without the need for an overlay. Ideal for applications where high performance variable data labels are needed, for example in defence, marine, rail and aerospace applications. Can be used as a wire/cable wraparound marker for substrates not less than 6mm (0.25 inches) diameter. Not recommended for outdoor use. PRINTING SYSTEM Print Quality and Print Performance can only be guaranteed when specific TE printer and ribbons are used. The current list of printers and ribbons can be found in TE document 411-121005 ‘Identification Printer Product Ribbon Matrix’ This document can be found at the TE document centre: http://www.te.com/commerce/DocumentDelivery/DDEController Raymark is fully supported by WINTOTAL and PrintEasy label printing software, available from the TE product store: http://www.te.com/en/general/label-printing-software.html Contact a TE representative for further information CURING CONDITIONS: 5 minutes at 150ºC (302ºF) in an air circulating oven. SHELF LIFE/STORAGE CONDITIONS: Can be stored unopened for 12 months at temperatures not exceeding 35ºC (95ºF). Once opened, product should be stored below 25ºC (77ºF) and 80% relative humidity and used within 6 months. SERVICE TEMPERATURE: Wiring marking: -40ºC to +85ºC (-40ºF to +185ºF) continuous. Panel marking: -40ºC to +105º (-40ºF to +221ºF) continuous. INSTALLATION TEMP: +10C to +40C (+50F to +104F). COLOURS: White. If the document is printed it becomes uncontrolled Check with TE Connectivity (TE) for latest version Author: L Smith Issue date: Aug 2014 Page: 1 of 3 While TE Connectivity Ltd. has made every reasonable effort to ensure the accuracy of the information in this document, TE does not guarantee that it is error-free, nor does TE make any other representation, warranty or guarantee that the information is accurate, correct, reliable or current. TE reserves the right to make any adjustments to the information contained herein at any time without notice. TE expressly disclaims all implied warranties regarding the information contained herein, including, but not limited to, any implied warranties of merchantability or fitness for a particular purpose. The dimensions in this document are for reference purposes only and are subject to change without notice. Specifications are subject to change without notice. Consult TE for the latest dimensions and design specifications. TECHNICAL DATA SHEET RayMark Six Labels Document number: TTDS-032 Issue: 2 Date: August 2014 Property Test Method Required Fungus Resistance BS EN 60068-2-10:2005 Print Legibility TE108-121012 Rating 1 (max) Legible, print contrast >3 Light fastness, xenon arc 250 hour, ASTM G155-05a Print Legibility TE108-121012 Adhesion to aluminium plate TE 108-121030 Legible, print contrast >3 20N/25mm adhesion Continuous humidity 168h, 40ºC (104ºF)/95% RH Print Legibility TE108-121012 Adhesion to aluminium plate TE 108-121030 Legible, print contrast >3 15N/25mm adhesion Thermal ageing 168h at 150ºC (302ºF) Print Legibility TE108-121012 Adhesion to aluminium plate TE 108-121030 Legible, 30N/25mm adhesion Thermal cycling 4 hours at -55ºC (-67ºF) 4 hours at 25°C (77°F) 4 hours at 150°C (302°F) 4 hours at 25°C (77°F) Print Legibility TE108-121012 Adhesion to aluminium plate TE 108-121030 Legible, 25N/25mm adhesion Dry abrasion resistance TE 109-121020 500 cycles, 500g, CS10 wheel Legible, print contrast >3 180° Adhesion to: Stainless steel Aluminium Acrylic painted surface ABS Nylon PVC TE 109-121030 If the document is printed it becomes uncontrolled Check with TE Connectivity (TE) for latest version 15 N/25mm 20 N/25mm 20 N/25mm 20 N/25mm 15 N/25mm 15 N/25mm Author: L Smith Issue date: Aug 2014 Page: 2 of 3 While TE Connectivity Ltd. has made every reasonable effort to ensure the accuracy of the information in this document, TE does not guarantee that it is error-free, nor does TE make any other representation, warranty or guarantee that the information is accurate, correct, reliable or current. TE reserves the right to make any adjustments to the information contained herein at any time without notice. TE expressly disclaims all implied warranties regarding the information contained herein, including, but not limited to, any implied warranties of merchantability or fitness for a particular purpose. The dimensions in this document are for reference purposes only and are subject to change without notice. Specifications are subject to change without notice. Consult TE for the latest dimensions and design specifications. TECHNICAL DATA SHEET RayMark Six Labels Document number: TTDS-032 Issue: 2 Date: August 2014 MARK PERMANENCE: Fluid Test Method Required MIL STD 202G Method 215 Solvent A Solvent B Solvent D TE 109-121014 30 strokes, toothbrush Legible, print contrast >3 Fluid Resistance 100°C, 2 hours:  Water 50°C, 24 hours:  Lubricating Oil O-149  Salt water solution (3.5% mass/mass) 23°C, 24 hours:  White Spirit  Iso Propyl Alcohol  Ethylene Glycol  Hydraulic Fluid H-515  Diesel Fuel 23°C, 1 hour:  Skydrol 500B4 Mark permanence and 180° Peel test to aluminium substraight Immersion, followed by Print Permanence, TE 109-121012, 20 rubs, 1kg load Print legible, minimum print contrast 3 10 N/25mm minimum Immersion followed by 180° peel test, TE 109-121030 Further information and availability can be found through the TE Cable Identification web site: http://www.te.com/catalog/labels-identification/menu/en/12933?BML=10576 If the document is printed it becomes uncontrolled Check with TE Connectivity (TE) for latest version Author: L Smith Issue date: Aug 2014 Page: 3 of 3 While TE Connectivity Ltd. has made every reasonable effort to ensure the accuracy of the information in this document, TE does not guarantee that it is error-free, nor does TE make any other representation, warranty or guarantee that the information is accurate, correct, reliable or current. TE reserves the right to make any adjustments to the information contained herein at any time without notice. TE expressly disclaims all implied warranties regarding the information contained herein, including, but not limited to, any implied warranties of merchantability or fitness for a particular purpose. The dimensions in this document are for reference purposes only and are subject to change without notice. Specifications are subject to change without notice. Consult TE for the latest dimensions and design specifications.