CA3260E

® CA3260, CA3260A Data Sheet December 10, 2009 FN1266.7 4MHz, BiMOS Operational Amplifier with MOSFET Input/CMOS Output CA3260A and CA3260 are integrated circuit operational amplifiers that combine the advantage of both CMOS and bipolar transistors on a monolithic chip. The CA3260 series circuits are dual versions of the popular CA3160 series. Gate protected P-Channel MOSFET (PMOS) transistors are used in the input circuit to provide very high input impedance, very low input current, and exceptional speed performance. The use of PMOS field effect transistors in the input stage results in common mode input voltage capability down to 0.5V below the negative supply terminal, an important attribute in single supply applications. A complementary symmetry MOS (CMOS) transistor pair, capable of swinging the output voltage to within 10mV of either supply voltage terminal (at very high values of load impedance), is employed as the output circuit. The CA3260 Series circuits operate at supply voltages ranging from 4V to 16V, or ±2V to ±8V when using split supplies. The CA3260A offers superior input characteristics over those of the CA3260. Features • MOSFET Input Stage provides - Very High ZI = 1.5TΩ (1.5 x 1012Ω) (Typ) - Very Low II . . . . . . . . . . . . 5pA (Typ) at 15V Operation . . . . . . . . . . . . . . . . . . . . . . 2pA (Typ) at 5V Operation • Ideal for Single Supply Applications • Common Mode Input Voltage Range Includes Negative Supply Rail; Input Terminals Can be Swung 0.5V Below Negative Supply Rail • CMOS Output Stage Permits Signal Swing to Either (Or Both) Supply Rails • Pb-Free Available (RoHS Compliant) Applications • Ground Referenced Single Supply Amplifiers • Fast Sample-Hold Amplifiers • Long Duration Timers/Monostables • Ideal Interface with Digital CMOS • High Input Impedance Wideband Amplifiers • Voltage Followers (e.g. Follower for Single Supply D/A Converter) Ordering Information PART NUMBER CA3260E CA3260EZ (Note) CA3260AE PART MARKING CA3260E CA3260EZ CA3260AE TEMP. RANGE (°C) -55 to +125 -55 to +125 -55 to +125 -55 to +125 PACKAGE 8 Ld PDIP 8 Ld PDIP* (Pb-free) 8 Ld PDIP 8 Ld PDIP* (Pb-free) PKG. DWG. # E8.3 E8.3 E8.3 E8.3 • Voltage Regulators (Permits Control of Output Voltage Down to 0V) • Wien Bridge Oscillators • Voltage Controlled Oscillators • Photo Diode Sensor Amplifiers CA3260AEZ 3260AEZ (Note) Pinout CA3260, CA3260A (8 LD PDIP) TOP VIEW *Pb-free PDIPs can be used for through hole wave solder processing only. They are not intended for use in Reflow solder processing applications. NOTE: These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. OUTPUT (A) INV. INPUT (A) NON INV. INPUT (A) V- 1 A 2 3 4 8 V+ OUTPUT (B) INV. INPUT (B) NON INV. INPUT (B) - + B + 7 - 6 5 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 1998, 2005, 2006, 2009. All Rights Reserved All other trademarks mentioned are the property of their respective owners. CA3260, CA3260A Absolute Maximum Ratings DC Supply Voltage (V+ to V-) . . . . . . . . . . . . . . . . . . . . . . . . . . 16V DC Input Voltage . . . . . . . . . . . . . . . . . . . . . . (V+ +8V) to (V- -0.5V) Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8V Input Terminal Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1mA Output Short Circuit Duration (Note 1). . . . . . . . . . . . . . . . Indefinite Thermal Information Thermal Resistance (Typical, Note 2) θJA (°C/W) θJC (°C/W) PDIP Package* . . . . . . . . . . . . . . . . . . 100 N/A Maximum Junction Temperature (Plastic Package) . . . . . . . +150°C Maximum Storage Temperature Range . . . . . . . . . -65°C to +150°C Pb-Free Reflow Profile. . . . . . . . . . . . . . . . . . . . . . . . .see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp *Pb-free PDIPs can be used for through hole wave solder processing only. They are not intended for use in Reflow solder processing applications. Operating Conditions Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . -55°C to +125°C CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty. NOTES: 1. Short circuit may be applied to ground or to either supply. 2. θJA is measured with the component mounted on an evaluation PC board in free air. Electrical Specifications PARAMETER Input Resistance Input Capacitance Unity Gain Crossover Frequency Slew Rate Transient Response TA = +25°C, Typical Values Intended Only for Design Guidance. TYPICAL VALUES SYMBOL RI CI fT SR Rise Time Overshoot tr OS tS VIO IIO II CMRR AOL TEST CONDITIONS VS = ±7.5V f = 1MHz, VS = ±7.5V VS = ±7.5V VS = ±7.5V CL = 25pF, RL = 2kΩ, AV = +1, VS = ±7.5V CL = 25pF, RL = 2kΩ, AV = +1, VS = ±7.5V V+ = 5V, V- = 0V V+ = 5V, V- = 0V V+ = 5V, V- = 0V V+ = 5V, V- = 0V VO = 4VP-P, RL = 20kΩ, V+ = 5V, V- = 0V V+ = 5V, V- = 0V VO = 5V, RL = ∞, V+ = 5V, V- = 0V VO = 2.5V, RL = ∞, V+ = 5V, V- = 0V ΔVIO/ΔV+, V+ = 5V, V- = 0V CA3260A 1.5 4.3 4 10 0.09 10 1.8 2 0.1 2 70 100 100 0 to 2.5 1 1.2 200 CA3260 1.5 4.3 4 10 0.09 10 1.8 6 0.1 2 60 100 100 0 to 2.5 1 1.2 200 UNITS TΩ pF MHz V/μs µs % μs mV pA pA dB kV/V dB V mA mA µV/V Settling Time (to