EL2286CS

EL2186, EL2286 ® Data Sheet September 26, 2001 250MHz/3mA Current Mode Feedback Amp w/Disable The EL2186/EL2286 are single/dual current-feedback operational amplifiers which achieve a -3dB bandwidth of 250MHz at a gain of +1 while consuming only 3mA of supply current per amplifier. They will operate with dual supplies ranging from ±1.5V to ±6V, or from single supplies ranging from +3V to +12V. The EL2186/EL2286 also include a disable/power-down feature which reduces current consumption to 0mA while placing the amplifier output in a high impedance state. In spite of its low supply current, the EL2286 can output 55mA while swinging to ±4V on ±5V supplies. The EL2186 can output 100mA with similar output swings. These attributes make the EL2186/EL2286 excellent choices for low power and/or low voltage cabledriver, HDSL, or RGB applications. For Single, Dual and Quad applications without disable, consider the EL2180 (8-Pin Single), EL2280 (8-Pin Dual) or EL2480 (14-Pin Quad). For lower power applications where speed is still a concern, consider the EL2170/EL2176 family which also comes in similar Single, Dual and Quad configurations. The EL2170/EL2176 family provides a -3dB bandwidth of 70MHz while consuming 1mA of supply current per amplifier. Ordering Information Features • Single (EL2186) and dual (EL2286) topologies • 3mA supply current (per amplifier) • 250MHz -3dB bandwidth • Low cost • Fast disable • Powers down to 0mA • Single- and dual-supply operation down to ±1.5V • 0.05%/0.05° diff. gain/diff. phase into 150Ω • 1200V/µs slew rate • Large output drive current: -100mA (EL2186) -55mA (EL2286) • Also available without disable in single (EL2180), dual (EL2280) and quad (EL2480) • Lower power EL2170/EL2176 family also available (1mA/70MHz) in single, dual and quad Applications • Low power/battery applications • HDSL amplifiers • Video amplifiers TEMP. RANGE PACKAGE PKG. NO. • Cable drivers EL2186CN -40°C to +85°C 8-Pin PDIP MDP0031 • RGB amplifiers EL2186CS -40°C to +85°C 8-Pin SOIC MDP0027 • Test equipment amplifiers EL2286CN -40°C to +85°C 14-Pin PDIP MDP0031 • Current to voltage converters EL2286CS -40°C to +85°C 14-Pin SOIC MDP0027 PART NUMBER FN7056 Pinouts EL2286* (14-PIN SO, PDIP) TOP VIEW EL2186* (8-PIN SO, PDIP) TOP VIEW *Manufactured under U.S. Patent No. 5,418,495 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright © Intersil Americas Inc. 2003. All Rights Reserved. Elantec is a registered trademark of Elantec Semiconductor, Inc. All other trademarks mentioned are the property of their respective owners. EL2186, EL2286 Absolute Maximum Ratings (TA = 25°C) Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +85°C Operating Junction Temperature Plastic Packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150°C Output Current (EL2186) . . . . . . . . . . . . . . . . . . . . . . . . . . . ±120mA Output Current (EL2286) . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±60mA Storage Temperature Range . . . . . . . . . . . . . . . . . .-65°C to +150°C Voltage between VS+ and VS- . . . . . . . . . . . . . . . . . . . . . . . . +12.6V Common-Mode Input Voltage . . . . . . . . . . . . . . . . . . . . . VS- to VS+ Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .±6V Current into +IN or -IN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .±7.5mA Internal Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . See Curves Operating Ambient CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests are at the specified temperature and are pulsed tests, therefore: TJ = TC = TA DC Electrical Specifications PARAMETER VS = ±5V, RL = 150Ω, ENABLE = 0V, TA = 25°C unless otherwise specified DESCRIPTION CONDITIONS MIN TYP MAX UNIT 2.5 15 mV VOS Input Offset Voltage TCVOS Average Input Offset Voltage Drift Measured from TMIN to TMAX dVOS VOS Matching EL2286 only +IIN + Input Current d+IIN + IIN Matching -IIN - Input Current d-IIN -IIN Matching EL2286 only CMRR Common Mode Rejection Ratio VCM = ±3.5V -ICMR - Input Current Common Mode Rejection VCM = ±3.5V PSRR Power Supply Rejection Ratio VS is moved from ±4V to ±6V -IPSR - Input Current Power Supply Rejection VS is moved from ±4V to ±6V ROL Transimpedance VOUT = ±2.5V 120 300 kΩ +RIN + Input Resistance VCM = ±3.5V 0.5 2 MΩ +CIN + Input Capacitance 1.2 pF CMIR Common Mode Input Range ±3.5 ±4.0 V VO Output Voltage Swing ±3.5 ±4.0 V VS = +5 Single-Supply, High 4.0 V VS = +5 Single-Supply, Low 0.3 V IO 5 µV/°C 0.5 mV 1.5 EL2286 only 20 16 Output Current VS = ±5 15 45 nA 40 µA 2 µA 50 dB 5 60 µA 30 70 1 µA/V dB 15 µA/V EL2186 only 80 100 mA EL2286 only, per Amplifier 50 55 mA IOUT, OFF Output Current Disable VOUT ±2V, AV = +1@25°C IS Supply Current ENABLE = 2.0V, per Amplifier IS(DIS) Supply Current (Disabled) COUT(DIS) 10 µA 3 6 mA ENABLE = 4.5V 0 50 µA Output Capacitance (Disabled) ENABLE = 4.5V 4.4 pF REN Enable Pin Input Resistance Measured at ENABLE = 2.0V, 4.5V 85 kΩ IIH Logic “1” Input Current Measured at ENABLE, ENABLE = 4.5V -0.04 µA IIL Logic “0” Input Current Measured at ENABLE, ENABLE = 0V -53 µA VDIS Minimum Voltage at ENABLE to Disable VEN Maximum Voltage at ENABLE to Enable 2 45 4.5 V 2.0 V EL2186, EL2286 AC Electrical Specifications PARAMETER VS = ±5V, RF = RG = 750Ω, RL = 150Ω, ENABLE = 0V, TA = 25°C unless otherwise specified DESCRIPTION CONDITIONS MIN TYP MAX UNIT -3dB BW -3dB Bandwidth AV = +1 250 MHz -3dB BW -3dB Bandwidth AV = +2 180 MHz 0.1dB BW 0.1dB Bandwidth AV = +2 50 MHz SR Slew Rate VOUT = ±2.5V, AV = +2 1200 V/µs tR, tF Rise and Fall Time VOUT = ±500mV 1.5 ns tPD Propagation Delay VOUT = ±500mV 1.5 ns OS Overshoot VOUT = ±500mV 3.0 % tS 0.1% Settling VOUT = ±2.5V, AV = -1 15 ns dG Differential Gain AV = +2, RL = 150Ω (Note1) 0.05 % dP Differential Phase AV = +2, RL = 150Ω (Note1) 0.05 dG Differential Gain AV = +1, RL = 500Ω (Note1) 0.01 % dP Differential Phase AV = +1, RL = 500Ω (Note1) 0.01 ° tON Turn-On Time AV = +2, VIN = +1V, RL = 150Ω (Note 2) 40 100 ns tOFF Turn-Off Time AV = +2, VIN = +1V, RL = 150Ω (Note 2) 1500 2000 ns CS Channel Separation EL2286 only, f = 5MHz 600 85 NOTES: 1. DC offset from 0V to 0.714V, AC amplitude 286mVP-P, f = 3.58MHz. 2. Measured from the application of the logic signal until the output voltage is at the 50% point between initial and final values. 3 dB EL2186, EL2286 Test Circuit (per Amplifier) Simplified Schematic (per Amplifier) 4 EL2186, EL2286 Typical Performance Curves Non-Inverting Frequency Response (Gain) Inverting Frequency Response (Gain) Transimpedance (ROL) vs Frequency 5 Non-Inverting Frequency Response (Phase) Inverting Frequency Response (Phase) PSRR and CMRR vs Frequency Frequency Response for Various RF and RG Frequency Response for Various RL and CL Frequency Response for Various CIN- EL2186, EL2286 Typical Performance Curves (Continued) Voltage and Current Noise vs Frequency -3dB Bandwidth and Peaking vs Supply Voltage for Various Non-Inverting Gains Supply Current vs Supply Voltage 6 2nd and 3rd Harmonic Distortion vs Frequency Output Voltage Swing vs Frequency -3dB Bandwidth and Peaking vs Supply Voltage for Various Inverting Gains Output Voltage Swing vs Supply Voltage Common-Mode Input Range vs Supply Voltage Slew Rate vs Supply Voltage EL2186, EL2286 Typical Performance Curves (Continued) Input Bias Current vs Die Temperature Short-Circuit Current vs Die Temperature Transimpedance (ROL) vs Die Temperature -3dB Bandwidth and Peaking vs Die Temperature for Various Non-Inverting Gains -3dB Bandwidth vs Die Temperature for Various Inverting Gains Input Offset Voltage vs Die Temperature Supply Current vs Die Temperature Input Voltage Range vs Die Temperature Slew Rate vs Die Temperature 7 EL2186, EL2286 Typical Performance Curves (Continued) Differential Gain and Phase vs DC Input Voltage at 3.58MHz Small-Signal Step Response Differential Gain and Phase vs DC Input Voltage at 3.58MHz Settling Time vs Settling Accuracy Large-Signal Step Response 8-Pin Plastic DIP Maximum Power Dissipation vs Ambient Temperature 14-Pin Plastic DIP Maximum Power Dissipation vs Ambient Temperature 8 8-Pin SO Maximum Power Dissipation vs Ambient Temperature 14-Pin SO Maximum Power Dissipation vs Ambient Temperature Channel Separation vs Frequency (EL2286) EL2186, EL2286 Applications Information Product Description The EL2186/EL2286 are current-feedback operational amplifiers that offer a wide -3dB bandwidth of 250MHz, a low supply current of 3mA per amplifier and the ability to disable to 0mA. Both products also feature high output current drive. The EL2186 can output 100mA, while the EL2286 can output 55mA per amplifier. The EL2186/EL2286 work with supply voltages ranging from a single 3V to ±6V, and they are also capable of swinging to within 1V of either supply on the input and the output. Because of their current-feedback topology, the EL2186/EL2286 do not have the normal gainbandwidth product associated with voltage-feedback operational amplifiers. This allows their -3dB bandwidth to remain relatively constant as closed-loop gain is increased. This combination of high bandwidth and low power, together with aggressive pricing make the EL2186/EL2286 the ideal choice for many low-power/high-bandwidth applications such as portable computing, HDSL, and video processing. For Single, Dual and Quad applications without disable, consider the EL2180 (8-Pin Single), EL2280 (8-Pin Dual) and EL2480 (14-Pin Quad). If lower power is required, refer to the EL2170/EL2176 family which provides Singles, Duals, and Quads with 70MHz of bandwidth while consuming 1mA of supply current per amplifier. Power Supply Bypassing and Printed Circuit Board Layout As with any high-frequency device, good printed circuit board layout is necessary for optimum performance. Ground plane construction is highly recommended. Lead lengths should be as short as possible. The power supply pins must be well bypassed to reduce the risk of oscillation. The combination of a 4.7µF tantalum capacitor in parallel with a 0.1µF capacitor has been shown to work well when placed at each supply pin. For good AC performance, parasitic capacitance should be kept to a minimum especially at the inverting input (see the Capacitance at the Inverting Input section). Ground plane construction should be used, but it should be removed from the area near the inverting input to minimize any stray capacitance at that node. Carbon or Metal-Film resistors are acceptable with the Metal-Film resistors giving slightly less peaking and bandwidth because of their additional series inductance. Use of sockets, particularly for the SO package should be avoided if possible. Sockets add parasitic inductance and capacitance which will result in some additional peaking and overshoot. Disable/Power-Down The EL2186/EL2286 amplifiers can be disabled, placing their output in a high-impedance state. When disabled, each amplifier's supply current is reduced to 0mA. Each EL2186/EL2286 amplifier is disabled when its ENABLE pin 9 is floating or pulled up to within 0.5V of the positive supply. Similarly, each amplifier is enabled by pulling its ENABLE pin at least 3V below the positive supply. For ±5V supplies, this means that an EL2186/EL2286 amplifier will be enabled when ENABLE is at 2V or less, and disabled when ENABLE is above 4.5V. Although the logic levels are not standard TTL, this choice of logic voltages allows the EL2186/EL2286 to be enabled by tying ENABLE to ground, even in +3V single-supply applications. The ENABLE pin can be driven from CMOS outputs or open-collector TTL. When enabled, supply current does vary somewhat with the voltage applied at ENABLE. For example, with the supply voltages of the EL2186 at ±5V, if ENABLE is tied to -5V (rather than ground) the supply current will increase about 15% to 3.45mA. Capacitance at the Inverting Input Any manufacturer's high-speed voltage- or current-feedback amplifier can be affected by stray capacitance at the inverting input. For inverting gains this parasitic capacitance has little effect because the inverting input is a virtual ground, but for non-inverting gains this capacitance (in conjunction with the feedback and gain resistors) creates a pole in the feedback path of the amplifier. This pole, if low enough in frequency, has the same destabilizing effect as a zero in the forward open-loop response. The use of large value feedback and gain resistors further exacerbates the problem by further lowering the pole frequency. The EL2186/EL2286 have been specially designed to reduce power dissipation in the feedback network by using large 750Ω feedback and gain resistors. With the high bandwidths of these amplifiers, these large resistor values would normally cause stability problems when combined with parasitic capacitance, but by internally canceling the effects of a nominal amount of parasitic capacitance, the EL2186/EL2286 remain very stable. For less experienced users, this feature makes the EL2186/EL2286 much more forgiving, and therefore easier to use than other products not incorporating this proprietary circuitry. The experienced user with a large amount of PC board layout experience may find in rare cases that the EL2186/EL2286 have less bandwidth than expected. In this case, the inverting input may have less parasitic capacitance than expected by the internal compensation circuitry of the EL2186/EL2286. The reduction of feedback resistor values (or the addition of a very small amount of external capacitance at the inverting input, e.g. 0.5pF) will increase bandwidth as desired. Please see the curves for Frequency Response for Various RF and RG, and Frequency Response for Various CIN-. EL2186, EL2286 Feedback Resistor Values The EL2186/EL2286 have been designed and specified at gains of +1 and +2 with RF = 750Ω. This value of feedback resistor gives 250MHz of -3dB bandwidth at AV = +1 with about 2.5dB of peaking, and 180MHz of -3dB bandwidth at AV = +2 with about 0.1dB of peaking. Since the EL2186/EL2286 are current-feedback amplifiers, it is also possible to change the value of RF to get more bandwidth. As seen in the curve of Frequency Response For Various RF and RG, bandwidth and peaking can be easily modified by varying the value of the feedback resistor. Because the EL2186/EL2286 are current-feedback amplifiers, their gain-bandwidth product is not a constant for different closed-loop gains. This feature actually allows the EL2186/EL2286 to maintain about the same -3dB bandwidth, regardless of closed-loop gain. However, as closed-loop gain is increased, bandwidth decreases slightly while stability increases. Since the loop stability is improving with higher closed-loop gains, it becomes possible to reduce the value of RF below the specified 750Ω and still retain stability, resulting in only a slight loss of bandwidth with increased closed-loop gain. Supply Voltage Range and Single-Supply Operation The EL2186/EL2286 have been designed to operate with supply voltages having a span of greater than 3V, and less than 12V. In practical terms, this means that the EL2186/EL2286 will operate on dual supplies ranging from ±1.5V to ±6V. With a single-supply, the EL2176 will operate from +3V to +12V. As supply voltages continue to decrease, it becomes necessary to provide input and output voltage ranges that can get as close as possible to the supply voltages. The EL2186/EL2286 have an input voltage range that extends to within 1V of either supply. So, for example, on a single +5V supply, the EL2186/EL2286 have an input range which spans from 1V to 4V. The output range of the EL2186/EL2286 is also quite large, extending to within 1V of the supply rail. On a ±5V supply, the output is therefore capable of swinging from -4V to +4V. Single-supply output range is even larger because of the increased negative swing due to the external pull-down resistor to ground. On a single +5V supply, output voltage range is about 0.3V to 4V. Video Performance For good video performance, an amplifier is required to maintain the same output impedance and the same frequency response as DC levels are changed at the output. This is especially difficult when driving a standard video load of 150Ω, because of the change in output current with DC level. Until the EL2186/EL2286, good Differential Gain could only be achieved by running high idle currents through the output transistors (to reduce variations in output impedance). These currents were typically comparable to the entire 3mA 10 supply current of each EL2186/EL2286 amplifier! Special circuitry has been incorporated in the EL2186/EL2286 to reduce the variation of output impedance with current output. This results in dG and dP specifications of 0.05% and 0.05° while driving 150Ω at a gain of +2. Video Performance has also been measured with a 500Ω load at a gain of +1. Under these conditions, the EL2186/EL2286 have dG and dP specifications of 0.01% and 0.01° respectively while driving 500Ω at AV = +1. Output Drive Capability In spite of its low 3mA of supply current, the EL2186 is capable of providing a minimum of ±80mA of output current. Similarly, each amplifier of the EL2286 is capable of providing a minimum of ±50mA. These output drive levels are unprecedented in amplifiers running at these supply currents. With a minimum ±80mA of output drive, the EL2186 is capable of driving 50Ω loads to ±4V, making it an excellent choice for driving isolation transformers in telecommunications applications. Similarly, the ±50mA minimum output drive of each EL2286 amplifier allows swings of ±2.5V into 50Ω loads. Driving Cables and Capacitive Loads When used as a cable driver, double termination is always recommended for reflection-free performance. For those applications, the back-termination series resistor will decouple the EL2186/EL2286 from the cable and allow extensive capacitive drive. However, other applications may have high capacitive loads without a back-termination resistor. In these applications, a small series resistor (usually between 5Ω and 50Ω) can be placed in series with the output to eliminate most peaking. The gain resistor (RG) can then be chosen to make up for any gain loss which may be created by this additional resistor at the output. In many cases it is also possible to simply increase the value of the feedback resistor (RF) to reduce the peaking. Current Limiting The EL2186/EL2286 have no internal current-limiting circuitry. If any output is shorted, it is possible to exceed the Absolute Maximum Ratings for output current or power dissipation, potentially resulting in the destruction of the device. Power Dissipation With the high output drive capability of the EL2186/EL2286, it is possible to exceed the 150°C Absolute Maximum junction temperature under certain very high load current conditions. Generally speaking, when RL falls below about 25Ω, it is important to calculate the maximum junction temperature (TJmax) for the application to determine if power-supply voltages, load conditions, or package type need to be modified for the EL2186/EL2286 to remain in the safe operating area. These parameters are calculated as follows: EL2186, EL2286 TJMAX = TMAX + (θJA * n * PDMAX) [1] where: TMAX=Maximum Ambient Temperature θJA=Thermal Resistance of the Package n=Number of Amplifiers in the Package PDMAX=Maximum Power Dissipation of Each Amplifier in the Package. PDMAX for each amplifier can be calculated as follows: PDMAX = (2 * VS * ISMAX) + (VS - VOUTMAX) * (VOUTMAX/RL) [2] where: VS=Supply Voltage ISMAX=Maximum Supply Current of 1 Amplifier VOUTMAX=Max. Output Voltage of the Application RL=Load Resistance Typical Application Circuits LOW POWER MULTIPLEXER WITH SINGLE-ENDED TTL INPUT 11 EL2186, EL2286 Typical Application Circuits (Continued) INVERTING 200mA OUTPUT CURRENT DISTRIBUTION AMPLIFIER FAST-SETTLING PRECISION AMPLIFIER 50 50 50 50 DIFFERENTIAL LINE-DRIVER/RECEIVER 12 EL2186, EL2286 EL2186/EL2286 Macromodel * EL2186 Macromodel * Revision A, March 1995 * AC characteristics used: Rf = Rg = 750 ohms * Connections: +input * | -input * | | +Vsupply * | | | -Vsupply * | | | | output * | | | | | .subckt EL2186/e. 2 7 4 6 * * Input Stage * e1 10 0 3 0 1.0 vis 10 9 0V h2 9 12 vxx 1.0 r1 2 11 400 l1 11 12 25nH iinp 3 0 1.5uA iinm 2 0 3uA r12 3 0 2Meg * * Slew Rate Limiting * h1 13 0 vis 600 r2 13 14 1K d1 14 0 dclamp d2 0 14 dclamp * * High Frequency Pole * e2 30 0 14 0 0.00166666666 l3 30 17 150nH c5 17 0 0.8pF r5 17 0 165 * * Transimpedance Stage * g1 0 18 17 0 1.0 rol 18 0 450K cdp 18 0 0.675pF * * Output Stage * q1 4 18 19 qp q2 7 18 20 qn q3 7 19 21 qn q4 4 20 22 qp r7 21 6 4 r8 22 6 4 ios1 7 19 1mA ios2 20 4 1mA * * Supply Current ips 7 4 0.2mA * * Error Terms * ivos 0 23 0.2mA 13 EL2186, EL2286 vxx 23 0 0V e4 24 0 3 0 1.0 e5 25 0 7 0 1.0 e6 26 0 4 0 -1.0 r9 24 23 316 r10 25 23 3.2K r11 26 23 3.2K * * Models * .model qn npn(is=5e-15 bf=200 tf=0.01nS) *.model qp pnp(is=5e-15 bf=200 tf=0.01nS) .model dclamp d(is=1e-30 ibv=0.266 + bv=0.71v n=4) .ends EL2186/EL2286 Macromodel All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 14