MMA02041001001FBLK

Metal Glaze™ General Purpose Surface Mount Power Resistor MM Series • Up to 2 watts • Up to 1000 volts • 0.1 ohm to 2.2 megohm range • 150°C maximum operating temperature 60/40 Solder over nickel barrier High temperature dielectric coating Metal Glaze™ thick film element fired at 1000°C to solid ceramic substrate Electrical Data Size Code Industry Footprint IRC Type Maximum Working Power Voltage² Rating 1/2 400 Resistance Range (ohms) 0.1 to 0.99 B 1206 MMA0204 1.0 to 1.0M 20 to 348K 0.1 to 0.99 F 2512 MMB0207 1 700 1.0 to 2.21M 20 to 348K H 3610 MMC0310 2 1000 0.1 to 0.99 1.0 to 2.21M Tolerance (+%)³ 1, 2, 5 1, 2, 5 0.25, 0.5 1, 2, 5 1, 2, 5 0.25, 0.5 1, 2, 5 1, 2, 5 TCR (ppm/°C)³ 100 50, 100 50, 100 100 50, 100 50, 100 100 50, 100 Product Category Low Range Standard Tight Tolerance Low Range Standard Tight Tolerance Low Range Standard ¹Not to exceed √P x R ²Consult factory for tighter TCR, tolerance, or resistance values. Environmental Data Characteristics Temperature Coefficient Thermal Shock Low Temperature Operation Short Time Overload High Temperature Exposure Resistance to Bonding Exposure Solderability Moisture Resistance Life Test Terminal Adhesion Strength Maximum Change As specified ±0.5% +0.01Ω ±0.25% +0.01Ω ±0.5% +0.01Ω ±1% for R>100KΩ ±0.5% +0.01Ω ±0.25% +0.01Ω Test Method MIL-R-55342E Par 4.7.9 (-55°C +125°C) MIL-R-55342E Par 4.7.3 (-65°C +150°C, 5 cycles) MIL-R-55342E Par 4.7.4 (-65°C @ working voltage) MIL-R-55342E Par 4.7.5 2.5 x √P x R for 5 seconds MIL-R-55342E Par 4.7.6 (+150°C for 100 hours) MIL-R-55342E Par 4.7.7 (Reflow soldered to board at 260°C for 10 seconds) 95% minimum coverage MIL-STD-202, Method 208 (245°C for 5 seconds) ±0.5% +0.01Ω ±0.5% +0.01Ω ±1% +0.01Ω no mechanical damage ±0.5% +0.01Ω no mechanical damage MIL-R-55342E Par 4.7.8 (10 cycles, total 240 hours) MIL-R-55342E Par 4.7.10 (2000 hours @ 70°C intermittent) 1200 gram push from underside of mounted chip for 60 seconds Chip mounted in center of 90mm long board, deflected 5mm so as to exert pull on chip contacts for 10 seconds Resistance to Board Bending General Note IRC reserves the right to make changes in product specification without notice or liability. All information is subject to IRC’s own data and is considered accurate at time of going to print. A subsidiary of TT electronics plc MM Series Issue March 2009 Sheet 1 of 3 Wire and Film Technologies Division • 4222 South Staples Street • Corpus Christi Texas 78411 USA Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com Metal Glaze™ General Purpose Surface Mount Power Resistor Physical Data L C W Size Code B F H Industry Footprint 1206 2512 3610 Dimensions (Inches and (mm) Actual Size L 0.128 ± 0.007 (3.25 ± 0.18) 0.251 ± 0.010 (6.38 ± 0.25) 0.367 ± 0.010 (9.32 ± 0.25) W 0.057 ± 0.006 (1.45 ± 0.15) 0.079 ± 0.006 (2.01 ± 0.15) 0.105 ± 0.006 (2.67 ± 0.15) C* 0.020 ± 0.010 (0.51 ± 0.25) 0.040 ± 0.010 (1.02 ± 0.25) 0.050 ± 0.010 (1.27 ± 0.25) *C dimension is average termination width. Recommended Solder Pad Dimensions (Reflow): F A C A B E D Size Code B F H Industry Footprint 1206 2512 3610 Dimensions (Inches and mm)) A 0.076 (1.93) 0.121 (3.07) 0.170 (4.32) B 0.093 (2.36) 0.126 (3.20) 0.160 (4.06) C 0.058 (1.47) 0.127 (3.23) 0.213 (5.41) D 0.098 (2.49) 0.183 (4.65) 0.273 (6.93) E 0.032 (0.81) 0.040 (1.02) 0.044 (1.12) F 0.211 (5.36) 0.369 (9.37) 0.553 (14.05) Wire and Film Technologies Division • 4222 South Staples Street • Corpus Christi Texas 78411 USA Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com MM Series Issue March 2009 Sheet 2 of 3 Metal Glaze™ General Purpose Surface Mount Power Resistor Standard Reel Packaging per EIA-481: Size Code B F H Industry Footprint 1206 2512 3610 Reel Diameter* 7″ 13″ 7" 13″ 13″ Quantity Per Reel 2,500 max. 10,000 max. 1,500 max. 5,000 max. 1,500 max. Carrier Tape Width 8mm 12mm 24mm Component Pitch 4mm 4mm 4mm *The 13″ reel is considered standard and will be supplied unless otherwise specified. Power Derating Curve 120 Repetitive Surge Curve 1000 Percent Relative Power 100 Peak Power (watts) 1/8, 1/2, 1 80 60 1 2 100 2 40 20 0 1/2 1/8 10 30 40 50 60 70 80 90 100 110 120 130 140 150 1 0.0001 .1msec 0.0010 1msec 0.0100 10msec 0.1000 100msec 1.0000 10000msec Ambient Temperature (°C) Surge or Pulse Duration (seconds) Note: Use for repetitive pulses where the average power dissipation is not to exceed the component rating at 70C. Surge handling capacity for low-repetitive surges may be significantly greater than shown above. Contact factory for recommendations. Ordering Data Sample Part No. IRC Type (MMA0204, MMB0207, MMC0310) MMA0204 50 2203 F 13 Temperature Coefficient 50 = ±50 ppm/°C; 100 = ±100 ppm/°C Note: RoHS compliance is noted by inserting “LF” into the part number immediately following the tolerance designator. RoHS compliant metallization is 96.5% Sn / 3% Ag / 0.5% Cu. RoHScompliant product is NOT backwards compatible to Sn/Pb soldering environments. Resistance Value (100 ohms and greater - First 3 significant figures plus 4th digit multiplier) Example: 100 ohms = 1000, 1000 ohms = 1001, 150,000 ohms = 1503 (Less than 100 ohms - ‘R’ is used to designate decimal) Example: 51 ohms = 51R0, 1 ohm = 1R00, 0.25 ohm = R250 Tolerance (D = 0.5%, F = 1.0%) Packaging Details (BLK = Bulk, 7 = 7" Reel, 13 = 13" Reel) Wire and Film Technologies Division • 4222 South Staples Street • Corpus Christi Texas 78411 USA Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com MM Series Issue March 2009 Sheet 3 of 3