OPIA801DTU

OPIA800—OPIA803, OPID804 DIP Package Features: • • • • 2,500 or 5,000 Vrms electrical isolation Choice of a Single and Dual LED Choice of Phototransistor or Photologic® Sensor Low-cost plastic Dual-In-Line (DIP) package Agency Approvals: • • UL Certification No: E58730 VDE NO: 40026713, 40026624 Description: The OPIA800 through OPID804 optocouplers are designed for applications that utilize a digital output (Phototlogic®) in a dual-in-line package. Isolation voltage from 2,500 to 5,000 Volts RMS product are designed for some of the most stringent power system isolation requirements. Theory of operation: The LED transmitter is used to illuminate the Photosensor providing electrical isolation between two power systems while maintaining the ability to transmit information from one power system to the other. In many applications, analog or digital signals may be required to be transmitted between two power systems while maintaining isolation between the power systems up to 5,000 volts RMS. A variety of LED and photosensor configurations are available depending on the system requirements The ratio Current Transfer Ratio (CTR) is determined using the output current and input current for analog photosensors. CTR ratios can range from as low as 5 to over 9,000 depending on the device. CTR = Photosenso r − Current 20 mA = *100 = 200 10 mA LED − Current All DIP product is shipped in a shipping tube with “TU” identified on the end of the part number. Example: OPIA800DTU is a 8-Pin DIP shipped in a tube (TU). Applications: • • High voltage isolation PCBoard power system isolation • • • Industrial equipment power isolation Medical equipment power isolation Office equipment 1 RoHS Moisture OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A.5 02/2010 Page 1 of 20 OPIA800—OPIA803, OPID804 DIP Package Analog Output Devices Ordering Information Part Number Isolation Voltage Max. (Vrms) CTR Min/Typ/Max Typ. Tplh / Tphl (ns) [RL = ohms] Package Configuration OPIA800 OPIA801 OPIA802 2,500 2,500 2,500 300 / 1,600 / 500 / 1,600 / 15 / 43 / - 7 / 2 [ 2.2 K] 10 / 5 [ 4.7 K] 0.3 / 0.3 [ 1.9 K] 8 Pin DIP 8 Pin DIP 8 Pin DIP A K—K A B C E (Dar) A K—K A B C E (Dar) A K—K A C E OPIA803 2,500 5 / 43 / - 0.4 / 0.3 [ 4.1 K] 8 Pin DIP A K—K A C E Digital Output Devices Ordering Information Isolation Voltage Max. (Vrms) 5,000 Part Number OPID804 LED 30 / 30 Configuration: Definition of Terms LED Identification—Sensor Identification K = Cathode 10K Inverted Logic NAND Gate A = Anode B = Base A = Anode 10K Logic K = Cathode Sensor Packaging Typ. Tplh / Tphl (ns) [RL = ohms] 45 / 45 [ 350] Typ. Tr / Tf (ns) [RL = 350 ohms] Part Number Suffix: Package Configuration 8 Pin DIP A K—NAND NAND Gate C = Collector E = Emitter D = DIP, TU = Ship in Tubes, TR = Ship on Tape and Reel Example: OPID606DTR Pin # Part Number 2 3 5 6 7 8 OPIA800 1 A K 4 E C C-B K-C OPIA801 A K E C C-B K-C OPIA802 A K E C A-B K OPIA803 A K E C A-B K OPID804 A K GND Output Enable Vcc Package Outline Dimensions and Schematics: Top-View OPIA802 OPIA803 OPIA800 OPIA801 Symbol Definition A Anode B Base C Collector E Emitter K Cathode DIMENSIONS ARE IN: INCHES [MILLIMETERS] TOLERANCE: ± 0.008 INCHES [± 0.2 MILLIMETERS] OPID804 OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A.5 02/2010 Page 2 of 20 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com OPIA800—OPIA803, OPID804 DIP Package Absolute Maximum Ratings (TA = 25o C unless otherwise noted) Storage Temperature Operating Temperature OPIA800 OPIA801 OPIA802 OPIA803 OPID804 Isolation voltage (1 minute) OPID804 OPIA800, OPIA801, OPIA802, OPIA803 -55° C to +125° C -40° C to +115° C 0° C to +125 ° C -55° C to +115° C -55° C to +100° C 0° C to +85° C 5,000 Vrms 2,500 Vrms Lead Soldering Temperature (1/16” (1.6 mm) from case for 5 seconds with soldering iron) 260° C Input Diode Continuous Forward Current OPIA802, OPIA803, OPID804 OPIA800 OPIA801 Peak Forward current (1 µs pulse width, 300 pps) OPIA800, OPIA801, OPIA802, OPIA803 OPID804 Reverse Voltage OPIA800, OPIA801, OPIA802, OPIA803, OPID804 Power Dissipation OPIA802, OPIA803, OPID804 OPIA800, OPIA801 25 mA 20 mA 1A 40 mA 5V 45 mW 35 mW Absolute Maximum Ratings (TA = 0° C to 70° C unless otherwise specified) Output IC Vcc—Collector-Emitter Voltage OPIA800 OPIA801 OPIA802, OPIA803 Collector Current OPIA802, OPIA803 OPIA800, OPIA801 Power Dissipation OPIA800, OPIA801, OPIA802, OPIA803 -0.5 V to +7 V -0.5 V to +18 V -0.5 V to +15 V 8 mA 60 mA 100 mW Output NAND Gate—OPID804 Vcc—Supply voltage Enable voltage High Level Output voltage Low Level Output current Output Collector Power Dissipation 7V 5.5 V 7V 50 mA 85 mW OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A.5 02/2010 Page 3 of 20 OPIA800—OPIA803, OPID804 DIP Package Electrical Characteristics: OPIA800 *6 Current transfer ratio is a ratio of input current and output current expressed in %. *7 Measured as 2-pin element (Short 1,2,3,4 and 5,6,7,8) OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A.5 02/2010 Page 4 of 20 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com OPIA800—OPIA803, OPID804 DIP Package Switching Characteristics: OPIA800 *9 Instantaneous common mode rejection voltage “output(1)” represents a common voltage variation that can hold the output above (1) level (Vo>2.0V). *10 Instantaneous common mode rejection voltage “output(1)” represents a common voltage variation that can hold the output above (0) level (Vo>0.8V). *8 Test Circuit Propagation Delay Time *10 Test Circuit for Instantaneous Common Mode Rejection Voltage OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A.5 02/2010 Page 5 of 20 OPIA800—OPIA803, OPID804 DIP Package OPIA800 Characteristic Curves OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A.5 02/2010 Page 6 of 20 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com OPIA800—OPIA803, OPID804 DIP Package OPIA800 Characteristic Curves OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A.5 02/2010 Page 7 of 20 OPIA800—OPIA803, OPID804 DIP Package Electrical Characteristics: OPIA801 (TA = 25°C) *6 Current transfer ratio is a ratio of input current and output current expressed in %. *7 Measured as 2-pin element (Short 1,2,3,4 and 5,6,7,8) OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A.5 02/2010 Page 8 of 20 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com OPIA800—OPIA803, OPID804 DIP Package Switching Characteristics: OPIA801 *9 Instantaneous common mode rejection voltage “output(1)” represents a common voltage variation that can hold the output above (1) level (Vo>2.0V). *10 Instantaneous common mode rejection voltage “output(1)” represents a common voltage variation that can hold the output above (0) level (Vo>0.8V). *8 Test Circuit Propagation Delay Time *10 Test Circuit for Instantaneous Common Mode Rejection Voltage OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A.5 02/2010 Page 9 of 20 OPIA800—OPIA803, OPID804 DIP Package Electrical Characteristics: OPIA802 (TA = 0 to +70°C unless otherwise specified) *5 Current transfer ratio is a ratio of input current and output current expressed in %. *6 Io = 2.4mA *7 Measured as 2-pin element (Short 1,2,3,4 and 5,6,7,8) OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A.5 02/2010 Page 10 of 20 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com OPIA800—OPIA803, OPID804 DIP Package Switching Characteristics: OPIA802 (TA = 25°C, VCC=5V, IF=16mA) *8 RL = 1.9k ohms is equivalent to on LSTTL and 5.6k ohm pull-up resistor. *9 Instantaneous common mode rejection voltage “output(1)” represents a common voltage variation that can hold the output above (1) level (Vo>2.0V). *10 Instantaneous common mode rejection voltage “output(1)” represents a common voltage variation that can hold the output above (0) level (Vo>0.8V). *11 Bandwidth represents a point where AC input goes down by 3dB. *9 Test Circuit Propagation Delay Time *11 Test Circuit for Instantaneous Common Mode Rejection Voltage OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A.5 02/2010 Page 11 of 20 OPIA800—OPIA803, OPID804 DIP Package Electrical Characteristics: OPIA803 (TA = 0 to +70°C unless otherwise specified) *5 Current transfer ratio is a ratio of input current and output current expressed in %. *6 Io = 1.1mA *7 Measured as 2-pin element (Short 1,2,3,4 and 5,6,7,8) OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A.5 02/2010 Page 12 of 20 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com OPIA800—OPIA803, OPID804 DIP Package Switching Characteristics: OPIA803 (TA = 25°C, VCC=5V, IF=16mA) *8 RL = 4.1k ohms is equivalent to on LSTTL and 6.1k ohm pull-up resistor. *9 Instantaneous common mode rejection voltage “output(1)” represents a common voltage variation that can hold the output above (1) level (Vo>2.0V). *10 Instantaneous common mode rejection voltage “output(1)” represents a common voltage variation that can hold the output above (0) level (Vo>0.8V). *11 Bandwidth represents a point where AC input goes down by 3dB. *9 Test Circuit Propagation Delay Time *11 Test Circuit for Instantaneous Common Mode Rejection Voltage OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A.5 02/2010 Page 13 of 20 OPIA800—OPIA803, OPID804 DIP Package (TA = 0 to +70°C unless otherwise specified) Electrical Characteristics: OPID804 SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS Forward Voltage (*4) - 1.6 1.8 V IF = 10 mA, TA = 25° C BVR Reverse Breakdown Voltage 5 - - V IR = 10 µA, TA = 25° C CIN Input Capacitance - 60 - pf VF = 0.0 V, f = 1M Hz IOL = 13 mA, VCC = 5.5 V, IF = 5 mA, VEH=2V Input Diode VF Output Photologic VOL Low Level Output Voltage - 0.4 0.6 V IOH High Level Output Current - 2 250 µA VCC=5.5 V, VO=5.5 V, VE=2.0 V, IF=250 µA IEH High Level Enable Current - -0.8 - mA VCC = 5.5 V, VE = 2.0 V IEL Low Level Enable Current -2.0 -1.2 - mA VCC = 5.5 V, VE = 2.0 V ICCL Low Level Output Current - 13 18 mA VCC = 5.5 V, VE = 0.5 V, IF = 10 mA ICCH High Level Output Current - 7 15 mA VCC = 5.5 V, VE = 0.5 V, IF = 0 mA II-O Leakage Current - - 1.0 mA VI-O = 3,000 V, TA = 25° C, t = 5 s, RH = 45% tEHL Enable Propagation delay “High to Low” (*8) - 15 ns tELH Enable Propagation delay “Low to High” (*8) - 40 - VEH = 3.0 V, VEL = 0.5 V, RL = 350 Ω , IF = 7.5 mA, CLOAD = 15 pf Hysteresis - 0.8 - Ratio VCC = 5 V, RL = 280 Ω RI-O Input-Output Isolation resistance (*5) - 1012 - ohm VI-O = 500 V, TA = 25° C CI-O Input-Output Capacitance (*5) - 0.6 - pf f = 1M Hz, TA = 25° C Propagation delay “High to Low” and “Low to High” (*7) - 45 75 ns tR & tF Rise and Fall Time - 30 - VCC = 5 V, RL = 350 Ω , IF = 7.5 mA, CLOAD = 15 pf, TA = 25°C CMH Instantaneous common mode rejection voltage “High Output” (*9) - 500 - CML Instantaneous common mode rejection voltage “Low Output” (*9) - -500 - IFHL / IFLH tPHL & tPLH V/us VCM = 10 V, RL = 350 Ω , IF = 0 mA, VO = 2.0 V VCM = 10 V, RL = 350 Ω , IF = 5 mA, VO = 0.8 V Notes: (Typical values are all at VCC = 5V, Ta = 25°C. *5 Measured as 2-Pin element. Connect pins 2 and 3, connect pins 5,6,7 and 8. *6 DC current transfer ratio is defined as the ratio of output collector current to forward bias input current. *7 Refer to Figure 1. *8 Refer to Figure 2. *9 CMH represents a common mode voltage ignorable rise time ratio that can hold logic (1) state in output. CML represents a common mode voltage ignorable fall time ratio that can hold logic (0) state in output. OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A.5 02/2010 Page 14 of 20 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com OPIA800—OPIA803, OPID804 DIP Package Recommended Operating Conditions: OPIA804 Truth Table Figure 1. Circuit Block Diagram Test Circuit Propagation Delay Time OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A.5 02/2010 Page 15 of 20 OPIA800—OPIA803, OPID804 DIP Package Recommended Operating Conditions (cont.): OPIA804 Test Circuit for Enable Propagation Delay Time Figure 2. Figure 3. Test Circuit for Instantaneous Common Mode Rejection Voltage OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A.5 02/2010 Page 16 of 20 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com OPIA800—OPIA803, OPID804 DIP Package OPID804 Characteristic Curves OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A.5 02/2010 Page 17 of 20 OPIA800—OPIA803, OPID804 DIP Package OPID804 Characteristic Curves OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A.5 02/2010 Page 18 of 20 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com OPIA800—OPIA803, OPID804 DIP Package Quality / Reliability Requirements Failure Criteria Conditions ± 10% 11 samples after 500Hrs 0 Fail @ VCE = 5.0VDC, Ta = 70°C ± 10% 50 samples after 96Hrs 0 Fail @ Max PD, Ta = 25°C MTTF @ 90% confidence 150,000 Min. @ 25°C, 25mADC Moisture Sensitivity Level MSL 1 per JDEC stnd J-STD-020B Lead Solderability 0 Fail per Method 208 of MIL-STD-202. 125°C Min. DSC test method Temperature Humidity-Bias ± 20% 85°C, 85%RH, 500Hrs, 80% min Iceo Temperature Cycle ± 20% per Method 1010.7 of MIL-STD-883E High Temperature Storage ± 20% 85°C, 500Hrs Autoclave 0 Fail TA = 121°C, Pressure = 15psi, Humidity = 100%, Time = 96Hrs Parameter HTRB D IC(OFF) HTFB D IC(ON) Glass Transition of body Note: This is to be performed when a change occurs to form, fit or function. Government and Industry Standard Compliance Requirements European Union’s Reduction of Hazardous Substances (RoHS) Directive 2002/95/EC Label Identification DESCRIPTION: Size: 3” (7.4 cm) X 2.2” (5.5 cm) Lettering shall be black on white background. Format shall be as: Notes: 1. The DATE CODE is a 4-digit code for date of manufacture where YY is the last two digits of the year, and WW is week number of manufacture. 2. The LOT I.D. is the manufacturing location lot identification where Y is the year of manufacture, NNNN is a sequential lot identifier, and DDD is the day of the year of manufacture. – or use equivalent label format. Carrollton, TX, USA MADE IN TAIWAN OPTEK P/N __OPIA800D-TU__ IIIIIIIIIIIIIIIIIIIII QTY. ________N/A_________ IIIIIIIIIIIIIIIIIIIII DATE CODE _____(YYWW)___ IIIIIIIIIIIIIIIIIIIII LOT I.D. ____(Y-NNNNDDD)__ IIIIIIIIIIIIIIIIIIIII OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A.5 02/2010 Page 19 of 20 OPIA800—OPIA803, OPID804 DIP Package Packaging Information: Tube Optek's Optocoupler Part Numbers Packaging Quantities 4-PIN OPIA400D/A, OPIA410D/A P/H OPIA413D/A and 6-PIN SMD OPIA6XXD/A Series 8-PIN OPIA8XXD Series and OPID804D Inner 52 x 7 x 7.5 cm Qty Small Carton Medium Carton Large Carton 53.5 x 16 x 17.5 cm 53.5 x 30.7 x 17.5 cm 53.5 x 30.7 x 25 cm Weight Qty Weight Qty Weight Gross Weight Qty Weight Gross Weight Qty Gross Weight Weig ht 100 44 3,000 1.40 12,000 6.0 6.5 24,000 12.0 12.5 36,000 18.0 18.5 65 44 1,950 1.50 7,800 6.5 7.0 15,600 12.0 12.5 23,400 18.5 19.0 48 44 1,440 1.44 5,760 6.0 6.5 11,520 12.0 12.5 17,290 18.0 18.5 100 24 6,000 1.60 24,000 6.5 7.0 48,000 13.0 13.5 72,000 19.5 20.0 170 -- 10,200 -- M/F 4-PIN and 5-PIN OPIA401B - OPIA404B, OPIA414B, OPIA500B SOP 4-PIN SSOP OPIA405C - OPIA409C P/H = Pin-Hole Packages (Referred as D = Dual-In-Line Package) SMD = Standard Surface Mount Packages (Referred as A = 6.5mil SMD) M/F or SOP = Mini-Flat Packages or Small Outside Packages (Referred as B = 4.40mil SMD w/ 2.54mil LeadSpacing) SSOP = Shrink SOP Packages (Referred as C = 3.60mil SMD with 1.27mil Lead-Spacing) Tube Packaging Specifications (TU): DIMENSIONS ARE IN: INCHES [MILLIMETERS] TOLERANCE: ± 0.008 INCHES [± 0.2 MILLIMETERS] Quantity: 8-pin: 48pcs/tube OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A.5 02/2010 Page 20 of 20 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com