P3406U_L

Multiport Balanced SIDACtor® Device RoHS ¨ 1 2 3 6 5 4 This six-pin SMT package offers a guaranteed balanced protection, based on a Littelfuse patent (US Patent 4,905,119). The ‘Y’ configuration offers identical metallic and longitudinal protection all in one package. SIDACtor devices enable equipment to comply with various regulatory requirements including GR 1089, ITU K.20, K.21, and K.45, IEC 60950, UL 60950, and TIA-968-A (formerly known as FCC Part 68). Electrical Parameters Part Number * P1556U_L P1806U_L P2106U_L P2356U_L P2706U_L P3206U_L P3406U_L P5106U_L VDRM Volts 130 150 170 200 230 270 300 420 VDRM Volts 170 400 VS Volts 180 210 250 270 300 350 400 600 VS Volts 250 550 VDRM Volt 130 150 170 200 230 270 300 420 VDRM Volt 50 270 VS Volts 180 210 250 270 300 350 400 600 VS Volts 80 340 VT Volts 8 8 8 8 8 8 8 8 IDRM µAmps 5 5 5 5 5 5 5 5 IS mAmps 800 800 800 800 800 800 800 800 IT Amps 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 IH mAmps 150 150 150 150 150 150 150 150 Pins 1-2, 2-3, 1-3 Pins 4-5, 5-6, 4-6 Part Number * A2106U_6L A5030U_6L Pins 1-2, 2-3, 4-5, 5-6 Pins 4-6, 1-3 VT Volts 3.5 3.5 IDRM µAmps 5 5 IS mAmps 800 800 IT Amps 2.2 2.2 IH mAmps 120 150 * “L” in part number indicates RoHS compliance. For non-RoHS compliant device, delete “L” from part number. For individual “UA”, “UB”, and “UC” surge ratings, see table below. General Notes: • All measurements are made at an ambient temperature of 25 °C. IPP applies to -40 °C through +85 °C temperature range. • IPP is a repetitive surge rating and is guaranteed for the life of the product. • Listed SIDACtor devices are bi-directional. All electrical parameters and surge ratings apply to forward and reverse polarities. • VDRM is measured at IDRM. • VS is measured at 100 V/µs. • Special voltage (VS and VDRM) and holding current (IH) requirements are available upon request. • Device is designed to meet balance requirements of GTS 8700 and GR 974. Surge Ratings in Amps IPP Series 0.2x310 * 2x10 * 8x20 * 0.5x700 ** 2x10 ** 1.2x50 ** Amps A B C 20 25 50 Amps 150 250 500 Amps 150 250 400 10x160 * 10x160 ** Amps 90 150 200 10x560 * 10x560 ** Amps 50 100 150 5x320 * 9x720 ** Amps 75 100 200 10x360 * 10x1000 * 5x310 * ITSM 10x360 ** 10x1000 ** 10x700 ** 50 / 60 Hz Amps 75 125 175 Amps 45 80 100 Amps 75 100 200 Amps 20 30 50 di/dt Amps/µs 500 500 500 * Current waveform in µs ** Voltage waveform in µs www.littelfuse.com 3 - 40 © 2006 Littelfuse • Telecom Design Guide Multiport Balanced SIDACtor® Device Thermal Considerations Package Modified MS-013 6 5 4 1 2 3 Symbol TJ TS RθJA Parameter Operating Junction Temperature Range Storage Temperature Range Thermal Resistance: Junction to Ambient Value -40 to +125 -65 to +150 60 Unit °C °C °C/W Capacitance Values pF Pin 1-2 / 3-2 (4-5 / 6-5) Tip-Ground, Ring-Ground Part Number P1556UAL P1556UBL P1556UCL P1806UAL P1806UBL P1806UCL P2106UAL P2106UBL P2106UCL P2356UAL P2356UBL P2356UCL P2706UAL P2706UBL P2706UCL P3206UAL P3206UBL P3206UCL P3406UAL P3406UBL P3406UCL P5106UAL P5106UBL P5106UCL A2106UA6L A2106UB6L A2106UC6L A5030UA6L A5030UB6L A5030UC6L MIN 10 15 20 10 15 15 15 20 15 15 15 15 10 10 15 10 10 25 10 10 15 10 10 30 10 10 10 10 10 20 MAX 30 60 60 55 55 55 55 55 55 50 50 50 50 50 50 45 45 45 45 45 45 45 45 45 30 30 45 45 45 35 MIN 10 25 30 20 25 30 15 20 30 15 20 25 15 20 25 15 20 45 15 15 20 15 15 25 20 20 20 15 15 25 pF Pin 1-3 (4-6) Tip-Ring MAX 45 95 55 85 85 85 85 85 85 75 75 75 75 75 75 70 70 70 65 65 65 35 35 40 60 60 70 35 35 40 Note: Off-state capacitance (CO) is measured at 1 MHz with a 2 V bias. Telecom Design Guide • © 2006 Littelfuse 3 - 41 www.littelfuse.com SIDACtor Devices Multiport Balanced SIDACtor® Device +I IPP – Peak Pulse Current – %IPP tr = r ise time to peak value td = decay time to half value IT IS IH IDRM -V VT VDRM VS +V 100 Peak Value Waveform = tr x td 50 Half Value 0 0 tr td t – Time (µs) -I V-I Characteristics tr x td Pulse Waveform Percent of VS Change – % 10 IH (TC = 25 ˚C) 14 12 8 6 4 2 0 -4 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160 2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 -40 -20 0 20 40 60 80 100 120 140 160 IH 25 ˚C 25 ˚C Ratio of Case Temperature (TC) – ˚C Junction Temperature (TJ) – ˚C Normalized VS Change versus Junction Temperature Normalized DC Holding Current versus Case Temperature www.littelfuse.com 3 - 42 © 2006 Littelfuse • Telecom Design Guide