20W Single Output LED Power Supply
Features :
PLP-20
series
Universal AC input / Full range(up to 277VAC) Protections:Short circuit/Over current/Over voltage/Over temperature Cooling by free air convection Built-in constant current limiting circuit with adjustable OCP level Built-in active PFC function Class power unit, no FG Small and compact size 100% full load burn-in test High reliability,low cost Suitable for built-in applications of LED lighting 2 years warranty
SPECIFICATION
MODEL DC VOLTAGE PLP-20-12 12V LED OPERATION VOLTAGE Note.5 9 ~ 12V 1.6A RATED CURRENT CURRENT RANGE CURRENT ADJ. RANGE 0 ~ 1.6A 75% ~ 100% 19.2W 10% 3.0% 10% 2300ms, 200ms / 230VAC 3000ms, 200ms / 115VAC at full load
Note.4 90 ~ 277VAC 127~392VDC
PLP-20-18 18V 13.5 ~ 18V 1.1A 0 ~ 1.1A 19.8W 3.0Vp-p
PLP-20-24 24V 18 ~ 24V 0.8A 0 ~ 0.8A 19.2W 3.0Vp-p
PLP-20-36 36V 27 ~ 36V 0.55A 0 ~ 0.55A 19.8W 3.0Vp-p
PLP-20-48 48V 36 ~ 48V 0.42A 0 ~ 0.42A 20.2W 3.8Vp-p
OUTPUT
RATED POWER RIPPLE & NOISE (max.) Note.2 2.5Vp-p VOLTAGE TOLERANCE Note.3 LINE REGULATION LOAD REGULATION SETUP, RISE TIME VOLTAGE RANGE FREQUENCY RANGE POWER FACTOR
47 ~ 63Hz PF 0.9 at 75~100% load, 115VAC/230VAC;PF 0.9 at 85~100% load 277VAC (Please refer to "Power Factor Characteristic" curve) 83% 80% 83.5% 82% 81% 0.4A/115VAC 40A/230VAC 0.5mA / 240VAC
Note.5
INPUT
EFFICIENCY(Typ.) AC CURRENT INRUSH CURRENT(max.) LEAKAGE CURRENT OVER CURRENT SHORT CIRCUIT
0.2A/230VAC
0.15A/277VAC
95 ~ 110% Protection type : Constant current limiting, recovers automatically after fault condition is removed Hiccup mode, recovers automatically after fault condition is removed. 27 ~ 34V 14 ~ 16V 19 ~ 22V Protection type : Shut off o/p voltage, clamping by zener diode 110 10 (TSW1) (Refer to "Derating Curve") 41 ~ 46V 54 ~ 60V
PROTECTION
OVER VOLTAGE OVER TEMPERATURE WORKING TEMP. WORKING HUMIDITY
Protection type : Shut down o/p voltage, recovers automatically after temperature goes down -30 ~ +60 20 ~ 90% RH non-condensing -40 ~ +80 , 10 ~ 95% RH 0.06%/ (0 ~ 50 ) 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes TUV EN61347-1, EN61347-2-13, UL8750,CSA C22.2 No. 250.0-08 approved I/P-O/P:3.75KVAC I/P-O/P:100M Ohms/500VDC / 25 / 70%RH Compliance to EN55015, EN61000-3-2 Class C( 75% load); EN61000-3-3 Compliance to EN61000-4-2,3,4,5,6,8,11, EN61547, light industry level, criteria A 643.6Khrs min. 140*32*22(L*W*H) 0.12kg;60pcs/9.2kg/0.62CUFT MIL-HDBK-217F (25 )
ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS WITHSTAND VOLTAGE SAFETY & ISOLATION RESISTANCE EMC EMC EMISSION EMC IMMUNITY MTBF OTHERS DIMENSION PACKING
NOTE
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. Derating may be needed under low input voltage, please check the static characteristic for more details. 5. Constant current operation region is within 75% ~100% rated output voltage. This is the suitable operation region for LED related applications, but please reconfirm special electrical requirements for some specific system design. 6. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again. 7. Direct connecting to LEDs is suggested, but is not suitable for using additional drivers.
File Name:PLP-20-SPEC 2012-03-13
20W Single Output LED Power Supply
Mechanical Specification
PLP-20
series
Unit:mm
5~8
300 10
3.5
140 133
300 10
5~8
3.5
UL 1015 18AWG
32 25
(BROWN) (BLUE)
AC/L AC/N
UL 1015 18AWG
+V -V
(RED) (BLACK)
Block Diagram
I/P EMI FILTER & RECTIFIERS POWER SWITCHING RECTIFIERS & FILTER +V -V O.C.P. DETECTION CIRCUIT
O.L.P.
PWM & PFC CONTROL
22
O.V.P.
Derating Curve
Static Characteristics
100
100 90
80
80 70
60
LOAD (%)
40
LOAD (%)
-25 -5 0 15 30 40 50 60 (HORIZONTAL)
60 50 40
20
-30
90
100
125
135
145
155 165
175
180
200
230
277
AMBIENT TEMPERATURE ( )
INPUT VOLTAGE (V) 60Hz
File Name:PLP-20-SPEC 2012-03-13
20W Single Output LED Power Supply
Power Factor Characteristic
Power factor will be higher than 0.9 when output loading is 75% or higher.
PLP-20
series
Constant Current Mode
1.00 0.98 0.96 0.94 0.92 0.90 0.88 0.86 0.84 0.82 0.80 0.78 50% 60% 70% 80% 90% 100%
(20W)
PF
277Vac 230Vac 115Vac
LOAD
EFFICIENCY vs LOAD (48V Model)
PLP-20 series possess superior working efficiency that up to 83.5% can be reached in field applications.
90 86 82 78 74 70 66 62 58 54 50 46 42 10%
EFFICIENCY (%)
277Vac 230Vac 115Vac
20%
30%
40%
50%
LOAD
60%
70%
80%
90% 100%
D RIVING METHODS OF LED MODULE
This LED power supply is suggested to work in constant current mode area (CC) to drive the LEDs.
100 Constant Current area
75 (max.) Hiccup Protection 50 100 Io (%)
Vo(%)
Typical LED power supply I-V curve
File Name:PLP-20-SPEC 2012-03-13
很抱歉,暂时无法提供与“PLP-20_12”相匹配的价格&库存,您可以联系我们找货
免费人工找货