0192210478

12 10 11 9 7 8 .015/(0.38) ±.100/(2.54) ±.035/(0.89) 2.344/(59.54) 1.844/(46.84) 2.062/(52.37) 2.156/(54.76) .728/(18.49) .728/(18.49) .728/(18.49) .728/(18.49) .824/(20.93) .824/(20.93) .824/(20.93) .824/(20.93) .824/(20.93) .916/(23.27) .916/(23.27) .916/(23.27) .916/(23.27) .999/(25.37) .999/(25.37) .999/(25.37) .984/(24.99) .728/(18.49) .824/(20.93) .916/(23.273) H G 192210652 F - BCL-4014 - 192210648 192210847 192210848 192210862 BCL-4014-PL BCL-1010MM-PL BCL-2010MM-PL BCL-3010MM-PL 1/4/(6.4) 10mm 10mm 10mm 4/0 1/0 2/0 3/0 .278/(7.061) .417/(10.59) .417/(10.59) .417/(10.59) 5 6 4 .050/(1.27) .020/(0.51) 3 2 1 ±.020/(0.50) H G J1 J1 J1 .550/(13.97) .460/(11.86) .522/(13.26) .501/(12.73) .559/(13.97) .400/(10.16) .461/(11.71) .511/(12.93) .135/(3.43) .110/(2.80) .110/(2.80) .115/(2.92) F E E D D C C B A B NOTE: 1. FOR INSPECTION SIGHT HOLE, PLEASE CONSULT FACTORY. 2. OTHER STUD SIZES MAY BE AVAILABLE, PLEASE CONSULT FACTORY. 3. MATERIAL: COPPER PLATING: TIN 4. MARKINGS CAN BE AT EITHER LOCATION SHOWN. 5. IF TONGUE IS TO BE BENT AT ANY ANGLE. IT MUST BE BENT AROUND A RADIUS ONE HALF THE TONGUE THICKNESS. J1 DOCUMENT STATUS 12 FORMAT: Eng-lega-master-tb-prod-C REVISION: E1 DATE: 2021/05/01 P1 RELEASE DATE 11 2022/11/30 10 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE IN/MM NTS CURRENT REV DESC: OBSOLETED PART NUMBERS AS PER PCN#510807. GENERAL TOLERANCES (UNLESS SPECIFIED) MM INCH 4 PLACES ± ± 3 PLACES ± ± 0.005 2 PLACES ± 0.13 ± ± 0.25 ± 1 PLACE 0 PLACES ± ANGULAR TOL 0.01 ± ± DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 11:33:18 9 8 7 6 5 ° EC NO: 726454 DRWN: LIKITV CHK'D: GGA APPR: GGA INITIAL REVISION: DRWN: BRE APPR: RWD THIRD ANGLE PROJECTION 4 2022/09/28 2022/11/30 2022/11/30 BATTERY CABLE LUG COPPER TERMINALS 1/0, 2/0, 3/0 & 4/0 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2002/06/24 2002/06/24 DRAWING SERIES C-SIZE 19221 3 SD-19221-011 MATERIAL NUMBER PSD 001 CUSTOMER GENERAL MARKET SEE TABLE 2 J2 SHEET NUMBER 1 OF 1 1 A