0873401096

9 7 8 6 5 4 3 2 1 PART NUMBER CKT. DIM. A DIM. B W/CAP IN TUBE SIZE A MAX. 4 6 8 10 12 14 16 18 20 87340-04*5 87340-06*5 87340-08*5 87340-10*5 87340-12*5 87340-14*5 87340-16*5 87340-18*5 87340-20*5 B 2.00 TYP E 2.00 4.00 6.00 8.00 10.00 12.00 14.00 16.00 18.00 20.00 2.00 4.00 6.00 8.00 10.00 12.00 14.00 16.00 18.00 PART NO. LEGEND 4.20 87340- **** PACKAGING 5 - TUBE 6 - T&R 1.10 D PLATING SEE NOTE 3 0.50 ±0.03 D CIRCUIT SIZE 1.05 SQ. (TYP.) NOTES: 5.95 4.80 MAX. 1. 0.90 ±0.13 CONTACT HEIGHT 2. 3.10 MAX. 2.15 MAX. C 0.30 4 ⌓ 0.10 4.90 E 5 C 3 . PLATING- 9 : 0.38µm MINIMUM GOLD PLATE AT CONTACT AREA, AND 1.90µm MINIMUM TIN PLATE AT P.C TAIL AREA, BOTH OVER 1.27µm MINIMUM NICKEL OVERALL. 3 : 0.05-0.25µm GOLD PLATE AT CONTACT AREA, AND 1.90µm MINIMUM TIN PLATE AT P.C TAIL AREA, BOTH OVER 1.27µm MINIMUM NICKEL OVERALL. 0.70 ±0.05 0.35 ±0.05 (2X) FOR ILLUSTRATION PURPOSES, DRAWING SHOWS PART WITH 12 CIRCUIT SIZE. MATERIAL: HOUSING: LCP GLASS FILLED, UL 94V-0 SUITABLE FOR SURFACE-MOUNT SOLDERING PROCESS. COLOR BLACK TERMINAL: PHOSPHOR BRONZE ALLOY. 6.10 4 . COPLANARITY OF P.C TAIL TO BE MEASURED BY RESTING THE PART ON A FLAT GAGE SURFACE. B 5 . THIS AREA OF PART TO BE HEAT-STAKED TO RETAIN CONTACTS. 6. POSITION OF CAP TO BE LOCATED AT CENTER OF DIMENSION "A" REGARDLESS OF CIRCUIT SIZE. 7. PRODUCT SPECIFICATION PS-87340 APPLIES. 8. PART TO BE PACKAGED IN TAPE-&-REEL. SEE SHEET 2 FOR PACKAGING DETAILS. 9. CONTACT FACTORY FOR PARTS AVAILABILITY. B 1.00 TYP (2X) 2.00 (TYP.) B 3.75 7.50 SYMBOLS 1.75 (TYP.) THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE = 0 mm NTS = 0 GENERAL TOLERANCES (UNLESS SPECIFIED) = 0 A 1.00 (TYP.) = 0 MM 4 PLACES ± = 0 (2X) RECOMMENDED SOLDER PAD DESIGN 2 PLACES ± ± 0.2 1 PLACE ± ± = 0 0 PLACES ± ± ANGULAR TOL DOCUMENT STATUS 9 P1 RELEASE DATE 2018/05/30 8 10:36:22 C 7 6 5 4 ± = 0 = 0 FORMAT: Met-lega-master-tb-prod-A3 REVISION: D DATE: 2018/01/18 INCH ± 3 PLACES ± ⌀ 0.80 ±0.05 = 0 CURRENT REV DESC: MIGRATED TO ECTR ± 3.0 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS EC NO: 172635 DRWN: RMV02 CHK'D: CD APPR: GGA INITIAL REVISION: DRWN: JWAN APPR: RWONG THIRD ANGLE PROJECTION 3 2018/02/20 2018/05/25 2018/05/30 MGRID, VLPR II TOP ENTRY RECEPT., SMT W/CAP FOR PICK-&-PLACE PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 1995/01/25 1995/01/25 SD-87340-XX92 MATERIAL NUMBER DRAWING SERIES A3-SIZE 87340 2 A SEE TABLE PSD 001 D4 SHEET NUMBER CUSTOMER GENERAL MARKET 1 1 OF 2 9 7 8 5 6 4 3 2 1 PART NO. CKT. Ao W/CAP IN TAPE/REEL SIZE Ko 2.00 E 4 Ao F Bo 4 6 8 10 12 14 16 20 87340-04*6 87340-06*6 87340-08*6 87340-10*6 87340-12*6 87340-14*6 87340-16*6 87340-20*6 4.00 1.75 ⌀ 1.55 +0.10 (TYP) 0.00 (PILOT HOLE) 6.70 6.50 6.70 6.70 6.60 6.60 6.60 6.70 Bo F W Ko 5.30 6.50 8.40 10.40 12.40 14.30 16.30 6.70 11.50 7.50 11.50 11.50 11.50 11.50 11.50 20.20 24.00 16.00 24.00 24.00 24.00 24.00 24.00 44.00 5.30 4.50 5.30 5.30 E 4.40 4.40 4.40 5.30 W ±0.3 D D 12.00 3.70 CUSTOMER PULL OUT DIRECTION COVER TAPE EMBOSSED CARRIER EMBOSSED CARRIER TAPE DIMENSIONS NOTES: C C 1. LEADER AND TRAILER TAPE 160 MIN. TOP TAPE TRAILER CUSTOMER PULL OUT DIRECTION 390 MIN TOP TAPE REEL TAPE AND REEL ASSEMBLY SHOWN IS FOR ILLUSTRATION ONLY. PULL OUT DIRECTION COMPONENT B 230 MIN. LEADER PART (EMPTY) 160 MIN. TAIL PART (EMPTY) B 2. PEELING OFF FORCE OF THE TOP TAPE: 20-80gf. (PEELING DIRECTION AS SHOWN IN FOLLOWING FIGURE) PART IN TUBE VIEW PEEL OFF DIRECTION 15° MAX. PULL OUT DIRECTION 3. PACKAGING STANDARD IS AS PER EIA-481. 4. TAPE & REEL QUANTITY = 1000 PCS/REEL 5 SYMBOLS NO FIX ORIENTATION OF ASSEMBLY PART IN T&R. THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE = 0 mm NTS = 0 GENERAL TOLERANCES (UNLESS SPECIFIED) = 0 A = 0 MM 4 PLACES ± 2 PLACES ± ± 0.2 1 PLACE ± ± = 0 0 PLACES ± ± ANGULAR TOL DOCUMENT STATUS 9 P1 RELEASE DATE 2018/05/30 8 10:36:22 C 7 6 5 4 ± = 0 = 0 FORMAT: Met-lega-master-tb-prod-A3 REVISION: D DATE: 2018/01/18 INCH ± 3 PLACES ± = 0 = 0 CURRENT REV DESC: MIGRATED TO ECTR ± 3.0 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS EC NO: 172635 DRWN: RMV02 CHK'D: CD APPR: GGA INITIAL REVISION: DRWN: JWAN APPR: RWONG THIRD ANGLE PROJECTION 3 2018/02/20 2018/05/25 2018/05/30 MGRID, VLPR II TOP ENTRY RECEPT., SMT W/CAP FOR PICK-&-PLACE PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 1995/01/25 1995/01/25 SD-87340-XX92 MATERIAL NUMBER DRAWING SERIES A3-SIZE 87340 2 A SEE TABLE PSD 001 D4 SHEET NUMBER CUSTOMER GENERAL MARKET 1 2 OF 2