0905712101

9 7 8 16.3 ±0.3 3 2 ⌀ 2.5 TYP.(2) 2.88 ⌀ 2.2 TYP.(2) 4.4 3.85 4.1 F 2.06 REF. ±0.3 1 C 4.1 30° 14.0 4 8.5 ±0.25 7.2 REF. 5.11 REF. F 5 6 4.7 REF. 10 E ±0.4 D ±0.45 B D 14.5 +0.4 -0.6 D 2.0 REF. CCT. NO. 1 I.D. MARK A 8.94 6.3 10.8 +0.4 -0.6 2.54 11.0 3.8 D A 5334 MXI 2.54 A F E 5.89 F B ±0.3 C ±0.45 E 3.0 MIN. TIN PLATE AREA. 26.6 REF. C C GOLD END OF PIN ⌖ 0.60 A ⌖ 0.80 B MEASURE POINT 3.0 FOR GOLD PLATING THICKNESS TYP. MIN. GOLD PLATE AREA. 5.10 6.0 2.54 2.54 ⌖ 0.70 C ⌖ 0.60 D DETAIL A SCALE 4:1 DIMENSIONS FOR SELECTIVE PLATING'S 5.8 ±0.3 7.4 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION A 3.50 ±0.5 SECTION F-F DOCUMENT STATUS 10 P1 RELEASE DATE 9 2019/05/20 DIMENSION UNITS SCALE mm 2:1 CURRENT REV DESC: CAD MIGRATION GENERAL TOLERANCES (UNLESS SPECIFIED) A FORMAT: master-tb-prod-A3 REVISION: H DATE: 2018/01/18 B 1.88 2.83 B NOTES: 1. FOR MATERIAL SPECIFICATION SEE NOTE 1. ON SHEET 2. 2. FOR RECOMMENDED P.C.B. HOLE PATTERN, PART NO's AND UNSTATED DIMENSIONS SEE SHHET 2. 3. PRODUCT SPEC. NO.: PS-99020-0015 ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± 0.5 ° 0.15 0.2 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 15:11:55 8 ANGULAR TOL 7 6 5 4 EC NO: 605552 DRWN: EEGBEDIRE CHK'D: TTOURISH APPR: DMAHER INITIAL REVISION: DRWN: SM APPR: EFOLAN THIRD ANGLE PROJECTION 2018/12/12 2019/04/15 2019/04/15 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 03/08/1990 2010/08/25 DRAWING SERIES A3-SIZE 90571 3 QIK FLECS WIPE FEMALE SDA-90571 MATERIAL NUMBER PSD 001 CUSTOMER SEE SHEET 2 2 GENERAL MARKET H1 SHEET NUMBER 1 OF 4 1 A 9 7 8 E 5 6 4 3 78.74 86.34 90.52 96.62 100.74 90571-1641 64 60.96 68.56 72.74 78.84 82.96 -1501 50 48.26 55.86 60.04 66.14 70.26 -1401 40 40.64 48.24 52.42 58.52 62.64 -1341 34 35.56 43.16 47.34 53.44 57.56 -1301 30 30.48 38.08 42.26 48.36 52.48 -1261 22.86 30.46 34.64 40.74 44.86 -1201 20 17.78 25.38 29.56 35.66 39.78 -1161 16 95071-1263 2 1 E 26 D D C 15.24 22.84 27.02 33.12 37.24 -1141 14 10.16 17.76 21.94 28.04 32.16 90571-1101 10 A B C D E ENG. NO. GS1 PLATING ENG. NO. GS2 PLATING NO. OF CKTS C 1.52 ±0.10 ⌀ 3.1 ±0.1 TYP.(x2) NOTES: 1. MATERIAL: GLASS FILLED POLYESTER (UL 94 V0), COLOUR-BLACK. PINS: BRASS SIZE 0.635. LEVER: GLASS FILLED POLYESTER (UL 94 V0), COLOUR-BLACK. 2.54 ±0.1 ⌀ 1.1 ±0.05 A ±0.2 B D ±0.3 2. PLATING OPTIONS. 90571-1**1, 1µm MIN. NICKEL UNDERPLATE. CONTACT AREA GS1 PLATING 0.1µ MIN. GOLD. SOLDER AREA 3µm MIN.TIN. B 90571-1**3, 1µm MIN. NICKEL UNDERPLATE. CONTACT AREA GS3 PLATING 0.25µ MIN. GOLD. SOLDER AREA 3µm MIN.TIN. 3. RECOMMENDED PCB THICKNESS 1.6mm 8.94 ±0.1 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION 2.54 ±0.1 DIMENSION UNITS SCALE mm 2:1 GENERAL TOLERANCES (UNLESS SPECIFIED) A ANGULAR TOL RECOMMENDED P.C.B. HOLE PATTERN DOCUMENT STATUS FORMAT: master-tb-prod-A3 REVISION: H DATE: 2018/01/18 9 P1 RELEASE DATE 2019/05/20 8 CURRENT REV DESC: CAD MIGRATION ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± 0.5 ° 0.15 0.2 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 15:11:55 7 6 5 4 QIK FLECS HEADER WITH DIN EJECT LEVERS FOR IMPROVED WIPE FEMALE EC NO: 605552 DRWN: EEGBEDIRE CHK'D: TTOURISH APPR: DMAHER INITIAL REVISION: DRWN: SM APPR: EFOLAN THIRD ANGLE PROJECTION 3 2018/12/12 2019/04/15 2019/04/15 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 03/08/1990 08/25/2010 SDA-90571 MATERIAL NUMBER DRAWING SERIES A3-SIZE 90571 2 A SEE CHART PSD 001 H1 SHEET NUMBER CUSTOMER GENERAL MARKET 1 2 OF 4 9 7 8 5 6 4 3 2 1 8.50 ±0.25 4.40 14.0 ±0.3 Y E D 6.30 4.75 3.80 0.95 1.0 REF. D 2.54 2.54 A C REF. B ±0.30 A B D REF. B 4.1 E X Z CCT. NO. 1 I.D. MARK W C C ⌖ 0.60 W ⌖ 0.80 X ⌖ 0.70 Y ⌖ 0.60 Z 3.0 MIN. TIN PLATE AREA. NOTES: 1. FOR MATERIAL SPECIFICATION SEE NOTE 1. ON SHEET 4. 2. FOR RECOMMENDED P.C.B. HOLE PATTERN, PART NO's AND UNSTATED DIMENSIONS SEE SHEET 4. 3. PRODUCT SPEC. NO.: PS-99020-0015 2.54 2.54 GOLD END OF PIN MIN. GOLD PLATE AREA. 5.10 1.88 2.83 B 7.40 3.5 ±0.5 MEASURE POINT 3.0 FOR GOLD PLATING THICKNESS TYP. 5.80 ±0.3 SECTION B-B DETAIL C SCALE 4:1 C THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSIONS FOR SELECTIVE PLATING'S DOCUMENT STATUS 9 P1 RELEASE DATE 2019/05/20 8 DIMENSION UNITS SCALE mm 2:1 ANGULAR TOL ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± 0.5 ° 0.15 0.2 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 15:11:55 7 6 5 CURRENT REV DESC: CAD MIGRATION GENERAL TOLERANCES (UNLESS SPECIFIED) A FORMAT: master-tb-prod-A3 REVISION: H DATE: 2018/01/18 B 4 EC NO: 605552 DRWN: EEGBEDIRE CHK'D: TTOURISH APPR: DMAHER INITIAL REVISION: DRWN: SM APPR: EFOLAN THIRD ANGLE PROJECTION 3 2018/12/12 2019/04/15 2019/04/15 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 03/08/1990 08/25/2010 SDA-90571 MATERIAL NUMBER DRAWING SERIES A3-SIZE 90571 2 A QUICK FLECS HEADER FOR IMPROVED WIPE FEMALE SEE SHEET 4 PSD 001 H1 SHEET NUMBER CUSTOMER GENERAL MARKET 1 3 OF 4 9 7 8 5 6 4 3 2 1 E E 22.86 30.46 32.36 -- 90571-2201 10.16 17.76 19.66 -- 90571-2101 A B C D ENG. NO. GS1 PLATING 90571-2203 20 10 ENG. NO. GS2 PLATING NO. OF CKTS D D C C 2.54 ±0.1 NOTES: 1. MATERIAL: GLASS FILLED POLYESTER (UL 94 V0), COLOUR-BLACK. PINS: BRASS SIZE 0.635. 2. PLATING OPTIONS. 90571-2**1, 1µm MIN. NICKEL UNDERPLATE. CONTACT AREA GS1 PLATING 0.1µ MIN. GOLD. SOLDER AREA 3µm MIN.TIN A ±0.2 ⌀ 1.10 ±0.05 B B 90571-2**3, 1µm MIN. NICKEL UNDERPLATE. CONTACT AREA GS3 PLATING 0.25µ MIN. GOLD. SOLDER AREA 3µm MIN.TIN. 3. RECOMMENDED PCB THICKNESS 1.6mm 2.54 ±0.1 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION RECOMMENDED P.C.B. HOLE PATTERN. DIMENSION UNITS SCALE mm 2:1 CURRENT REV DESC: CAD MIGRATION GENERAL TOLERANCES (UNLESS SPECIFIED) A DOCUMENT STATUS FORMAT: master-tb-prod-A3 REVISION: H DATE: 2018/01/18 9 P1 RELEASE DATE 2019/05/20 8 ANGULAR TOL ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± 0.5 ° 0.15 0.2 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 15:11:55 7 6 5 4 EC NO: 605552 DRWN: EEGBEDIRE CHK'D: TTOURISH APPR: DMAHER INITIAL REVISION: DRWN: SM APPR: EFOLAN THIRD ANGLE PROJECTION 3 2018/12/12 2019/04/15 2019/04/15 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 03/08/1990 08/25/2010 SDA-90571 MATERIAL NUMBER DRAWING SERIES A3-SIZE 90571 2 A QIK FLECS HEADER FOR IMPROVED WIPE FEMALE SEE CHART PSD 001 H1 SHEET NUMBER CUSTOMER GENERAL MARKET 1 4 OF 4