50-57-9314

PRODUCT SPECIFICATION SL BOX CRIMP TERMINAL 1.0 SCOPE This Product Specification covers the crimp terminal #70058-**** used with the single row fully stackable connector housing #70066-****, the dual row fully stackable connector housing #70450-****, and the dual row with latch connector housing #74130-****. 2.0 PRODUCT DESCRIPTION 2.1 PRODUCT NAME AND SERIES NUMBER(S) 70058 Box Crimp Terminal 2.2 DIMENSIONS, MATERIALS, PLATINGS AND MARKINGS 2.2.1 For information on dimensions see the individual sales drawings. 2.2.2 Material: High strength copper alloy 2.2.3 Plating 2.2.3.1 Tin: 3.81 micrometers/150 microinches minimum tin plate overall over nickel underplate overall 2.2.3.2 Tin-Lead: 3.81 micrometers/150 microinches minimum tin-lead (90-10) plate overall over nickel underplate overall 2.2.3.3 50 Gold: 1.25 micrometers/50 microinches minimum gold plate in contact area; 1.91 micrometers/75 microinches minimum tin plate in crimp area; over nickel underplate overall 2.2.3.4 30 Gold: 0.76 micrometers/30 microinches minimum gold plate in contact area; 1.91 micrometers/75 microinches minimum tin plate in crimp area; over nickel underplate overall 2.2.3.5 15 Gold: 0.38 micrometers/15 microinches minimum gold plate in contact area; 1.91 micrometers/75 microinches minimum tin plate in crimp area; over nickel underplate overall 2.2.3.6 Tin-Sel: 3.81 micrometers/150 microinches minimum tin plate in contact area; 1.91 micrometers/75 microinches minimum tin plate in crimp area; over nickel underplate overall 2.2.4 Connector Assemblies Mates with: 2.2.4.1 0.64 mm/.025 in square round pins assembled directly into PC board on .100 centers 2.2.4.2 Shrouded or unshrouded single or dual-row wafers, with 0.64mm/.025in square or round pins 2.2.4.2 70021 Crimp Terminal REVISION: I ECR/ECN INFORMATION: EC No: UCP2010-0987 DATE: 2009 / 10 / 13 DOCUMENT NUMBER: PS-70058 TITLE: PRODUCT SPECIFICATION FOR SL CRIMP TERMINAL SERIES 70058 SHEET No. 1 of 4 CREATED / REVISED BY: CHECKED BY: APPROVED BY: ACHAMMER/MIBARRA SMILLER JCOMERCI TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC PRODUCT SPECIFICATION 2.2.5 Connector to accept wire range from 36 to 20 AWG. For recommended wire types and crimp heights, contact the Molex Inside Sales department. 3.0 APPLICABLE DOCUMENTS AND SPECIFICATIONS 3.1 3.2 3.3 Mil Std. 202 IEC 68-2-14 IEC 69-2-42 4.0 PERFORMANCE 4.1 MECHANICAL REQUIREMENTS 4.1.1 Insertion/Withdrawal Forces 4.1.1.1 Tin Plating System: 150 microinches minimum Tin over nickel underplate overall 4.1.1.2 Gold Plating System: 30 microinches minimum Gold over nickel underplate overall 4.1.1.3 Steel gage pins used to perform test: Insertion Gage Pin: .0260+.0000/-.0001 Withdrawal Gage Pin: .0240+.0001/-.0000 AVERAGE INSERTION AND WITHDRAWAL FORCES * PLATING TYPE AFTER 1 CYCLE INSERTION WITHDRAWAL FORCE FORCE TIN 4.1.1.1 GOLD 4.1.1.2 .32 lbf 1.4 N .34 lbf 1.5 N .26 lbf 1.2 N .18 lbf 0.8 N AFTER 10 CYCLES AFTER 25 CYCLES INSERTION FORCE WITHDRAWAL FORCE INSERTION FORCE .23 lbf 1.0 N .27 lbf 1.2 N .27 lbf 1.2 N .15 lbf 0.7 N .24 lbf 1.1 N No Data AFTER 50 CYCLES WITHDRAWAL INSERTION WITHDRAWAL FORCE FORCE FORCE .25 lbf 1.1 N No Data No Data .25 lbf 1.1 N No data .14 lbf 0.6 N 4.2 ELECTRICAL/ENVIRONMENTAL REQUIREMENTS Note: These requirements apply to the 70058 terminal only 4.2.1 The following performance criteria is based on grouped, sequential testing 4.2.2 All contact resistance values measured at 20 millivolts maximum open circuit voltage and 5-15 milliamperes using the 4 point dry circuit method, with a Hewlett-Packard Milliohmeter, Model #4328A. 4.2.3 All tin contact systems cycled 1, 5 & 25 times prior to grouped sequential testing, using 0.64mm/.025 in square pins with 150 microinches minimum tin over nickel underplate overall All gold contact systems cycled 1, 25 & 50 times prior to grouped sequential testing, using 0.64mm/.025 in square pins with 30 microinches minimum gold over nickel underplate overall REVISION: I ECR/ECN INFORMATION: EC No: UCP2010-0987 DATE: 2009 / 10 / 13 DOCUMENT NUMBER: PS-70058 TITLE: PRODUCT SPECIFICATION FOR SL CRIMP TERMINAL SERIES 70058 SHEET No. 2 of 4 CREATED / REVISED BY: CHECKED BY: APPROVED BY: ACHAMMER/MIBARRA SMILLER JCOMERCI TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC PRODUCT SPECIFICATION 4.2.4 Group I Sequence: Mated Environment Test/Specifications 5.4.1 Thermal Shock IEC 68-2-14 5.4.2 Thermal Aging Mil. Std. -202F, 108A Cyclic Humidity Mil. Std. -202F, 106D without cold dip 5.4.3 Test Severity/Duration -40°C to +105°C 30 minute dwell at each temperature is one cycle. 10 cycles +105°C for 10 days Temperature cycles between +25°C to +65°C at 96% R.H. for 240 hours. Exposed to sulphur vapors for 24 hours at +65°C. 5.4.4 Flowers of Sulphur 5.4.5 Contact resistance to be less than 10 milliohm change from Initial 4.2.4 Group II Sequence: Mated Environment Test/Specifications 5.5.1 Thermal Shock IEC 68-2-14 5.5.2 Thermal Aging Mil. Std. -202F, 108A Steady State Humidity Mil. Std. -202F, 103B Condition A 5.5.3 5.5.4 Flowers of Sulphur IEC 69-2-42 Mate once, contact resistance to be less than 10 milliohm change from Initial 5.5.5 REVISION: I Test Severity/Duration ECR/ECN INFORMATION: EC No: UCP2010-0987 DATE: 2009 / 10 / 13 DOCUMENT NUMBER: PS-70058 TITLE: -40°C to +105°C 30 minute dwell at each temperature is one cycle. 10 cycles +105°C for 10 days +40°C at 96% R.H. for 10 days Exposed to sulphur vapors for 24 hours at +65°C PRODUCT SPECIFICATION FOR SL CRIMP TERMINAL SERIES 70058 SHEET No. 3 of 4 CREATED / REVISED BY: CHECKED BY: APPROVED BY: ACHAMMER/MIBARRA SMILLER JCOMERCI TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC PRODUCT SPECIFICATION 4.2.4 Group III Sequence: Mated Environment Test/Specifications 5.6.1 Test Severity/Duration Steady State Humidity, Mil. Std. -202F, 103B Condition A Physical Shock Mil. Std. -202F 213B 5.6.2 5.6.3 Vibration Mil. Std. -202F, 201A 5.6.4 Contact resistance to be less than 10 milliohm change from Initial +40°C at 96% R.H. for 10 days. ½ Sine Wave, 50G, 11MS pulse 3 shocks per axis for 240 hours. 10-55-10 HZ, 1 minute cycles for 2 hours in each axis. .03 inch excursion, 10G. 4.2.4 Group IV Sequence: Mated Environment Test/Specifications 5.7.1 5.7.2 Steady State Humidity, Mil. Std. -202F, 103B Condition A Temperature Rise 5.7.3 Current Ratings: Test Severity/Duration +40°C at 96% R.H. for 10 days. Increase current to achieve 30°C rise above ambient. Dwell for 48 hours at that current. 30 Awg - 0.7A | 36 Awg - 0.21A 28 Awg - 1.2A | 34 Awg - 0.32A 26 Awg - 1.8A | 32 Awg - .045A 24 Awg - 3.0A | 22 Awg - 3.0A | 4.2.4 Capacitance: Less than 1.2 pico-farads Note: For Assembly (Housing/Terminal) environmental requirements see Product Specification PS-70400 5.0 PACKAGING Parts shall be packaged to protect against damage during handling, transit and storage. See Sales drawings for packaging specification. REVISION: I ECR/ECN INFORMATION: EC No: UCP2010-0987 DATE: 2009 / 10 / 13 DOCUMENT NUMBER: PS-70058 TITLE: PRODUCT SPECIFICATION FOR SL CRIMP TERMINAL SERIES 70058 SHEET No. 4 of 4 CREATED / REVISED BY: CHECKED BY: APPROVED BY: ACHAMMER/MIBARRA SMILLER JCOMERCI TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC