A223R

A200R Series Compact, Regulated, 2W Single & Dual Output DC/DC Converters Electrical Specifications Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Input Key Features: Parameter Conditions ● 2W Output Power Input Voltage Range ● Compact DIP Case ● 500 VDC Isolation ● Tight Line/Load Regulation Input Filter Reverse Polarity Input Current ● Single & Dual Outputs Short Circuit Input Power ● 20 Standard Models Output ● 1.0 MH MTBF Parameter ● Industry Standard Pin-Out Output Voltage Accuracy Output Voltage Balance Line Regulation Load Regulation Ripple & Noise (20 MHz) (Note 1) Ripple & Noise (20 MHz) Ripple & Noise (20 MHz) Output Power Protection Transient Recovery Time (Note 2) Transient Response Deviation Temperature Coefficient Output Short Circuit Min. 5 VDC Input 4.5 12 VDC Input 10.8 24 VDC Input 21.6 48 VDC Input 43.2 π (Pi) Filter Typ. 5.0 12.0 24.0 48.0 Max. 5.5 13.2 26.4 52.8 0.5 2,000 Units VDC A mW Units % % % % mV P - P mV P - P mV rms % μSec % %/ºC Conditions Dual Output , Balanced Loads Vin = Min to Max Iout = 10% to 100% Over Line, Load & Temp. Min. Typ. ±2.0 ±1.0 ±0.2 ±0.2 40 Max. ±4.0 ±3.0 ±0.3 ±0.5 50 75 5 50 ±6.0 ±0.02 120 50% Load Step Change ±0.01 Continuous Conditions 60 Seconds 500 VDC 100 kHz, 1V Min. 500 1,000 40 Conditions Typ. Max. General Parameter Isolation Voltage Isolation Resistance Isolation Capacitance Switching Frequency Units VDC MΩ pF kHz Units ºC ºC ºC % 100 80 150 Environmental Parameter Operating Temperature Range Storage Temperature Range Cooling Humidity Min. Typ. -25 -25 -40 Free Air Convection RH, Non-condensing Max. +71 +90 +125 95 MicroPower Direct 232 Tosca Drive Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: sales@micropowerdirect.com W: www.micropowerdirect.com Physical Case Size Case Material Weight 1.25 x 0.80 x 0.40 Inches (31.8 x 20.3 x 10.2 mm) Non-Conductive Black Plastic (UL94-V0) 0.42 Oz (12g) Conditions MIL HDBK 217F, 25ºC, Gnd Benign Conditions 5 VDC Input 12 VDC Input 24 VDC Input 48 VDC Input 1.5 mm From Case For 10 Sec. All Models Min. Typ. 800 Typ. Max. Units kHours Units VDC ºC mW Reliability Specifications Parameter MTBF Absolute Maximum Ratings Parameter Input Voltage Surge (1 Sec) Lead Temperature Internal Power Dissipation Min. -0.7 -0.7 -0.7 -0.7 Max. 7.5 15.0 30.0 55.0 260 3,000 Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. Model Selection Guide Model Number A201R A202R A203R A204R A205R A211R A212R A213R A214R A215R A221R A222R A223R A224R A225R A231R A232R A233R A234R A235R Notes: Voltage (VDC) Nominal 5 5 5 5 5 12 12 12 12 12 24 24 24 24 24 48 48 48 48 48 Range 4.5 - 5.5 4.5 - 5.5 4.5 - 5.5 4.5 - 5.5 4.5 - 5.5 10.8 - 13.2 10.8 - 13.2 10.8 - 13.2 10.8 - 13.2 10.8 - 13.2 21.6 - 26.4 21.6 - 26.4 21.6 - 26.4 21.6 - 26.4 21.6 - 26.4 43.2 - 52.8 43.2 - 52.8 43.2 - 52.8 43.2 - 52.8 43.2 - 52.8 Output Fuse Rating Reflected Efficiency Slow-Blow Current Ripple Voltage Current (%, Typ) (mA) (VDC) (mA, Max) (mA, Min) Full-Load No-Load Current (mA, Typ) Input Current (mA) 800 730 690 740 740 330 295 265 280 280 163 135 135 135 135 83 70 70 80 80 80 80 80 80 80 40 40 40 40 40 20 20 20 20 20 10 10 10 10 10 80 80 80 80 80 30 30 30 30 30 15 15 15 15 15 10 10 10 10 10 5.0 12.0 15.0 ±12.0 ±15.0 5.0 12.0 15.0 ±12.0 ±15.0 5.0 12.0 15.0 ±12.0 ±15.0 5.0 12.0 15.0 ±12.0 ±15.0 400 165 133 ±83 ±66 400 165 133 ±83 ±66 400 165 133 ±83 ±66 400 165 133 ±83 ±66 0.0 0.0 0.0 ±0.0 ±0.0 0.0 0.0 0.0 ±0.0 ±0.0 0.0 0.0 0.0 ±0.0 ±0.0 0.0 0.0 0.0 ±0.0 ±0.0 50 54 57 53 51 50 56 62 59 59 51 61 61 61 61 50 59 59 51 51 1,500 1,500 1,500 1,500 1,500 700 700 700 700 700 350 350 350 350 350 135 135 135 135 135 1. When measuring output ripple, it is recommended that an external 0.33 μF ceramic capacitor be placed from the +Vout pin to the -Vout pin for single output units and from each output to common for dual output units. For noise sensitive applications, the use of 1.5 μF capacitors will reduce the output ripple. 2. Transient recovery is measured to within a 1% error band for a load step change of 50% to 100%. 3. Operation at no-load will not damage these units. However, they may not meet all specifications. 4. Dual output units may be connected to provide a 24 VDC or 30 VDC output. To do this, connect the load across the positive (+Vout) and negative (-Vout) outputs and float the output common. 5. The converter should be connected to a low ac-impedance source. An input source with a highly inductive impedance may affect the stability of the converter. In applications where the converter output loading is high and input power is supplied over long lines, it may be necessary to use a capacitor on the input to insure start-up. In this case, it is recommended that a low ESR (ESR