P1900

PASSIVE POWER FACTOR CORRECTION INDUCTORS P1900 SERIES • • • • • • • Designed for use in off-line AC-DC pre-regulators circuits for switching power converters applications Low core loss and high flux density Insulation class system: B (130°C), F (155°C) or H(180°C) Dielectric Withstanding Voltage (DWV): 2KVRMS Operating Temperature: -20°C to +105°C RoHS Compliant Product Custom Design Available ELECTRICAL PARAMETERS @ 25°C Part Number P19000 P19001 P19002 P19003 P19004 P19005 P19006 P19007 P19008 P19009 L (μH MIN)1 Terminal3 (S-F) 1-5, 2-4 1-5, 2-4 1-5, 2-4 1-5, 2-4 1-5, 2-4 1-5, 2-4 1-5, 2-4 2-5 2-5 2-5 DCR (mΩ MAX)1, 2 28 53 120 55 55 118 90 95 241 286 I @ 80% L (ADC) 16.50 14.80 10.60 12.20 12.20 11.20 11.40 7.50 6.40 5.70 I @ 65% L (ADC) 37.00 33.00 24.00 27.00 27.00 25.00 26.00 17.00 14.00 13.00 I @ 50% L (ADC) 60.00 53.50 38.50 44.00 44.00 40.50 41.50 27.00 23.00 20.50 I @ 30% L (ADC) 60.00 53.50 38.50 44.00 44.00 40.50 41.50 27.00 23.00 20.50 Pins Dia. (Ø AWG) 14 x 2 14 x 2 15 x 2 15 x 2 15 x 2 15 x 2 15 x 2 14 15 15 LxWxH (in. MAX) 2.7x1.0x2.8 2.7x1.0x2.8 2.6x1.0x2.7 2.6x1.0x2.7 2.6x2.6x1.0 2.6x1.0x2.7 2.6x1.0x2.7 2.7x1.0x2.8 2.7x1.0x2.8 2.7x1.0x2.8 PCB Mounting Layout V / Fig. 2 V / Fig. 2 V / Fig. 3 V / Fig. 3 H / Fig. 4 V / Fig. 3 V / Fig. 3 V / Fig. 1 V / Fig. 1 V / Fig. 1 240 290 400 440 440 490 500 820 1600 2000 1. Test conditions: 10KHz, 1VRMS. 2. Combined resistance of the “x2” winding. 3. Only those assigned terminals will have the self-lead pins. DIMENSIONS (mm) VERTICAL L W SCHEMATICS Figure 2 0.25 [6.35] 0.50 [12.70] Figure 1 0.60 [15.24] 1.20 [30.48] H 0.18 [4.57] P19XXX MPS DC 1.00 [25.40] 6 5 4 0.85 [21.59] 1.00 [25.40] 654 0.85 [21.59] S F 1 2 2.00 [50.80] 3 123 2.00 [50.80] 1 2 3 Ø AWG HORIZONTAL L&W Figure 3 1.575 [40.005] 0.20 [5.08] 54 0.85 [21.59] 0.984 [25.000] Typ. 2 Figure 4 ØL P19XXX MPS DC H 1.00 [25.40] 6 1 12 3 1.375 [34.925] 2.00 [50.80] 0.18 [4.57] 2 1 0.20 [5.08] Typ. Product performance is limited to specified parameters. Data is subject to change without prior notice. Dimensions Unless otherwise specified, all tolerances are: inch: .XX : ±0.015 .XXX : ±0.004 mm: X,X : ±0,38 X,XX : ±0,10 Tel: 310-325-1043 Fax: 310-325-1044 www.mpsind.com sales@mpsind.com