HPR117VC

HPR1XXVC www.murata-ps.com 0.75 Watt Single Output DC/DC Converter Discontinued HPR1XXVC Series. The high efficiency of the HPR1XXVC Series means less internal power dissipation, as low as 190mW. With reduced heat dissipation the HPR1XXVC Series can operate at higher temperatures with no degradation. In addition, the high efficiency of the HPR1XXVC Series means the series is able to offer greater than 10 W/inch3 of output power density. Operation down to no load will not impact the reliability The HPR1XXVC Series uses advanced circuit design and packaging technol‑ ogy to deliver superior reliability and perfor‑ mance. A 170kHz push-pull oscillator is used in the input stage. Beatfrequency oscillation problems are reduced when using the HPR1XXVC Series with high frequency isolation amplifiers. Reduced parts count and high efficiency add to the reliability of the of the series, although a >1mA minimum load is needed to realize published specifications. The HPR1XXVC Series provides the user a low cost converter without sacrificing reliabil‑ ity. The use of surface mounted devices and advanced manufacturing technologies make it possible to offer premium performance and low cost. SPECIFICATIONS All specifications are typical at TA = +25°C nominal input voltage unless otherwise specified. PRODUCT SELECTION CHART Nominal Input Voltage VDC Rated Output Voltage VDC Rated Output Current mA HPR117VC 15 ±15 ±25 8 63 5 79 MEA1D1515DC HPR100VC HPR105VC HPR101VC HPR102VC HPR103VC HPR104VC HPR106VC HPR107VC HPR108VC HPR109VC HPR110VC HPR111VC HPR112VC HPR113VC HPR114VC HPR115VC HPR116VC HPR118VC HPR119VC HPR120VC HPR121VC HPR122VC HPR123VC 5 5 5 5 5 5 12 12 12 12 12 12 15 15 15 15 15 24 24 24 24 24 24 5 ±15 12 15 ±5 ±12 5 12 15 ±5 ±12 ±15 5 12 15 ±5 ±12 5 12 15 ±5 ±12 ±15 150 ±25 62 50 ±72 ±30 150 62 50 ±72 ±30 ±25 150 62 50 ±72 ±30 150 62 50 ±72 ±30 ±25 20 20 20 20 20 20 10 10 10 10 10 10 8 8 8 8 8 8 8 8 8 8 8 216 200 212 212 218 212 90 81 81 88 81 81 72 72 72 72 63 48 48 45 45 45 45 10 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 15 15 15 15 15 15 69 75 70 71 68 68 69 77 77 71 74 77 69 69 69 69 76 65 65 76 69 67 69 NKE0505DC / NME0505DC NMA0515DC / MEA1D0515DC NKE0512DC / NME0512DC NKE0515DC / NME0515DC NMA0505DC / MEA1D0505DC NMA0512DC / MEA1D0512DC NKE1205DC / NME1205DC NKE1212DC / NME1212DC NKE1215DC / NME1215DC NMA1205DC / MEA1D1205DC NMA1212DC / MEA1D1212DC NMA1215DC / MEA1D1215DC MEV1S1505DC MEV1S1512DC MEV1S1515DC MEA1D1505DC MEA1D1512DC NME2405DC / MEV1S2405DC NME2412DC / MEV1S2412DC NME2412DC / MEV1S2415DC MEA1D2405DC MEA1D2412DC MEA1D2415DC Model Discontinued For full details go to www.murata-ps.com/rohs Input Current Reflected Efficiency Rated Load Ripple Current No Load Typ. mA mAp-p % Recommended Alternatives * www.murata-ps.com/support TDC_HPR1XXVC.D03 Page 1 of 4 HPR1XXVC 0.75 Watt Single Output DC/DC Converter SPECIFICATIONS, ALL MODELS GENERAL OUTPUT INPUT Specifications are at TA = +25°C nominal input voltage unless otherwise specified. PARAMETER CONDITIONS MIN TYP MAX UNITS INPUT Voltage Range 4.5 5 5.5 VDC 10.8 12 13.2 VDC 13.5 15 16.5 VDC 21.6 24 26.4 VDC Voltage Rise Time See Typical Performance Curves & Application Notes: “Capacitive Loading Effects on Start-Up of DC/DC Converters” OUTPUT Rated Power 750 mW Voltage Setpoint Accuracy Rated Load, Nominal VIN ±5 % Ripple & Noise BW = DC to 10MHz 150 200 mVp-p BW =10Hz to 2MHz 30 40 mVrms Voltage (Over Input Voltage Range) 1mA to Rated Current, VOUT = 5V 4.75 7 VDC 1mA to Rated Current, VOUT = 12V 11.40 15 VDC 1mA to Rated Current, VOUT = 15V 14.25 18 VDC Temperature Coefficent .01 .05 %/ °C REGULATION Load Regulation (All other modes) Rated Load to 1mA Load 3 % GENERAL ISOLATION Rated Voltage 750 VDC Test Voltage 60 Hz, 10 Seconds 750 Vrms Resistance 10 GW Capacitance 25 100 pF Leakage Current VISO= 240VAC, 60Hz 2 8.5 mArms Switching Frequency 170 kHz Frequency Change Over Line and Load 24 % Package Weight 3 g MTTF per MIL-HDBK-217, Rev. F* Circuit Stress Method Ground Benign TA = +25°C 7.9 MHr Fixed Ground TA = +35°C 1.9 MHr Naval Sheltered TA = +35°C 1.2 MHr Airborne Uninhabited Fighter TA = +35°C 300 kHr TEMPERATURE Specification -25 +25 +85 °C Operation -40 +100 °C Storage -40 +110 °C SOLDERING INFORMATION The HPR1XXVC devices are intended for wave soldering or manual soldering. They are not intended to be subject to surface mount processes under any circumstances. The normal wave soldering process can be used with these devices where the device is subjected to a maximum wave temperature of 260°C for a period of no more than 10 seconds. Within this time and temperature range, the integrity of the device’s plastic body will not be compromised and internal temperatures within the converter will not exceed 175°C. Care should be taken to control manual soldering limits identical to that of wave soldering. www.murata-ps.com/support TDC_HPR1XXVC.D03 Page 2 of 4 HPR1XXVC 0.75 Watt Single Output DC/DC Converter TYPICAL PERFORMANCE CURVES Specifications are at TA = +25°C nominal input voltage and nominal load. VOUT VS LOAD (5Vout Models) VOUT VS LOAD (±5Vout Models) 5.7 5.4 5.5 5.2 VOUT VS LOAD (12Vout Models) 12.5 5.3 5.0 5.1 4.8 4.9 4.6 0 80 40 120 12.3 Vout Vout Vout 12.4 160 12.1 12.0 0 20 Output Current (mA) 12.3 15.3 12.1 15.1 12.0 14.9 10 20 20 30 40 80 60 16.0 15.5 15.0 14.5 14.0 0 20 40 60 13.5 80 Output Current each load (mA) Output Current each load (mA) EFFICIENCY VS LOAD OSCILLATION FREQUENCY VS TEMPERATURE 90 40 VOUT VS LOAD (±15Vout Models) 16.5 15.5 12.2 0 0 Output Current each load (mA) Vout Vout Vout 11.9 80 15.7 12.4 0.2 0 0.4 0.6 0.8 1.0 Output Power each load (Watts) 220 Frequency (KHz) 75 Efficiency (%) 60 VOUT VS LOAD (15Vout Models) 15.9 12.5 60 45 30 15 0 40 Output Current each load (mA) VOUT VS LOAD (±12Vout Models) 12.6 12.2 0 20 60 40 80 200 180 160 140 100 -30 0 % of Rated Load (%) 30 60 90 Temperature (°C) SAFE OPERATING AREA LOAD CAPACITANCE vs INPUT RISE TIME (5 Vout models) 600 50 Total Load Capacitance (uF) Total Load Capacitance (uF) 500 400 300 SAFE OPERATING AREA 200 40 30 SAFE OPERATING AREA 20 10 100 0 0 0 5 10 15 20 25 30 35 Rise Time of Input Voltage (mS) 40 45 50 LOAD CAPACITANCE vs INPUT RISE TIME (12 Vout models) 90 Total Load Capacitance (uF) LOAD CAPACITANCE vs INPUT RISE TIME (15 Vout models) 60 60 50 SAFE OPERATING AREA 30 20 10 0 5 10 15 20 25 30 35 40 10 15 20 25 30 35 40 45 50 Rise Time of Input Voltage (mS) 1.) When operated within the SAFE OPERATING AREA as defined by the above curves, the output voltage of HPR1XXC devices is guaranteed to be within 95% of its steady-state value within 100 milliseconds after the input voltage has reached 95% of its steady- state value. 70 0 5 NOTES: 80 40 0 45 50 2.) For dual output models, total load capacitance is the sum of the capacitances on the plus and minus outputs. Rise Time of Input Voltage (mS) www.murata-ps.com/support TDC_HPR1XXVC.D03 Page 3 of 4 HPR1XXVC 0.75 Watt Single Output DC/DC Converter MECHANICAL PACKAGE/PINOUT “V” DIP PACKAGE 0.785±0.010" (19.94±0.25) 14 13 TOP VIEW 11 10 9 8 0.695±0.015" (17.65±0.38) 0.525±0.010" (13.34±0.25) 1 2 3 4 5 6 7 0.375±0.005" (9.52±0.13) 0.015±0.005" (0.38±0.13) SIDE VIEW 0.020±0.002" (0.51±0.05) 0.100±0.010" (2.54±0.25) 0°-15° 0.600" (15.24) PIN CONNECTIONS PIN# 1 2 3 4 5 6 SINGLES DUALS PIN# SINGLES +VIN +VIN 7 -VIN -VIN 8 NC NC 9 NC NC 10 -VOUT -VOUT 11 NC Common 13 14 DUALS +VOUT +VOUT NC NC NC NC NC NC NC NC NC NC NC NC ABSOLUTE MAXIMUM RATINGS Internal Power Dissipation......................................... 450mW Short Circuit Duration................................................. Momentary 0.125+0.030" -0.000" (3.18+0.76) BOTTOM ( -0.00) VIEW NOTES: NC = Do Not Connect. Duplicate pin functions are internally connected. All dimensions are in inches (millimeters). GRID: 0.100 inches (2.54 millimeters) MATERIAL: Lead material is phosphor bronze; lead finish is 100-300 microinches of matte tin over a nickel barrier layer of 5-40 microinches. ORDERING INFORMATION HPR 1XX V Device Family HPR Indicates DC/DC Converter Model Number Selected from Table of Electrical Characteristics C Package Option V = DIP Package RoHS Compliant Version Murata Power Solutions, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1151 U.S.A. ISO 9001 and 14001 REGISTERED This product is subject to the following operating requirements and the Life and Safety Critical Application Sales Policy: Refer to: http://www.murata-ps.com/requirements/ Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without notice. 2017 Murata Power Solutions, Inc. www.murata-ps.com/support TDC_HPR1XXVC.D03 Page 4 of 4