SAFFB1G96FN0F0AR1X

Data Sheet of SAW Components Note : Murata SAW Component is applicable for Cellular /Cordless phone (Terminal) relevant market only. Please also read caution at the end of this document. SAW FILTER FOR UMTS Band2 Rx Murata part number : SAFFB1G96FN0F0A Package Dimensions Specification Specification Item Top View -30 to 85°C 25±2°C typ. 1.10±0.05 (1) Dot Marking(φ0.2) H 9X $ ＊ Insertion Loss (1930.48 to 1989.52 MHz) (1932.4 to 1987.6MHz)* (0.15) 2-0.25±0.03 (3) (0.075) 5-0.25±0.03 Bottom View (2) (1) (0.05) 2-0.20±0.03 (5) 1960MHz 4.0 dB max. 3.5 dB max. 3.1 dB 4.0 dBINT max. 3.5 dBINT max. 3.0 dBINT Absolute Attenuation (3) 0.5max. (2) Nominal Center Frequency(fc) (4) 0.90±0.05 (5) (4) 5-0.20±0.03 2-0.20±0.03 Marking: Laser Printing : EIAJ Code (Refer to the table 1) $ : Date Code (Refer to the table 2) (1) : Unbalance Port (3)(4) : Balance Port Others : Ground 1) 0.1 to 824 MHz 50 dB min. 50 dB min. 63 dB 2) 824 to 849 MHz 50 dB min. 50 dB min. 63 dB 3) 849 to 1850 MHz 45 dB min. 45 dB min. 56 dB 1910 MHz 46 dB min. 46 dB min. 50 dB 46 dBINT min. 46 dBINT min. 53 dBINT 4) 1850 to 5) 1852.4 to 6) 2400 to 2484 MHz 40 dB min. 40 dB min. 54 dB 7) 3860 to 3980 MHz 40 dB min. 40 dB min. 53 dB 8) 3980 to 6000 MHz 40 dB min. 40 dB min. 51 dB 1907.6 MHz * Ripple Deviation (1930.48 to 1989.52 MHz) 2.5 dB max. 1.8 dB max. 1.2 dB VSWR (1930.48 to 1989.52 MHz) 2.0 max. 1.9 max. 1.6 Amplitude Balance (1930.48 to 1989.52 MHz) ±1.0dB max. ±1.0dB max. 0.5dB Phase Balance (1930.48 to 1989.52 MHz) 180±7deg. max. Unbalance Port Matching Impedance (nominal) Balance Port Matching Impedance (nominal) Input Signal Level * 180±7deg. 180.0+4.7deg. max. 50Ω 100Ω//22nH 31.6mW (+15dBm), 2000 hours (1850-1910 MHz, at 50℃) 20mW (+13dBm), 2000hours (elsew here) * Integration calculation (dBINT): Unit : mm Aug. 1, 2017 1/7 SAW FILTER FOR UMTS Band2 Rx Murata part number : SAFFB1G96FN0F0A Frequency Performance Amplitude Balance Aug. 1, 2017 Phase Balance 2/7 SAW FILTER FOR UMTS Band2 Rx Murata part number : SAFFB1G96FN0F0A Dimensions of Carrier Tape A: 8.0 B: 1.75 C: 3.50 D: 4.0 E: 2.00 F: 2.0 G: φ1.5 H: 0.75 J: 1.05 K: 1.25 L: 0.55 Unit: mm Dimensions of Tape Trailer tape 160...190 Components 80...120 Leader Cavity 400...560 Unit: mm Dimensions of Reel 2.0±0.5 (φ60) 13.5max. (φ178) 9.0±0.5 φ13.0±0.5 Unit: mm SAFFB1G96FN0F0AR1X  10000pcs/reel (φ1789 SAFFB1G96FN0F0AR1S  sample Order (φ1789 Aug. 1, 2017 3/7 SAW FILTER FOR UMTS Band2 Rx Murata part number : SAFFB1G96FN0F0A Top View 4-0.325 Recommended Land Pattern 0.9 0.25 1.1 0.25 2-0.25 2-0.20 2-0.20 2-0.20 : Land Pattern Unit : mm Test Circuit Bottom View 2 3 1 R1 Aug. 1, 2017 50Ω L22nH 5 R100Ω 2 4 4/7 SAW FILTER FOR UMTS Band2 Rx Murata part number : SAFFB1G96FN0F0A RoHS Compliance This component is compliant with RoHS directive. This component was always RoHS compliant from the first date of manufacture. ・ Caution - Limitation of Applications This product is intended for the following applications only; however, please do not use this product in these applications where defects might directly cause damage to a third party’s life, body or property. a. Mobile Telephone b. Cordless phone (except for Automotive use9 c. PC (Including Notebook PC, Netbook PC, Tablet9 d. Game e. Camera (except for Business/security use9 f. Set Top Box g. Electronic dictionary h. Digital audio equipment ・This catalog is for reference only and not an official product specification document, therefore, please review and approve our official product specification before ordering this product. Marking code Table 1 : EIAJ Code *This rule of code is applied repeatedly every four year. Table 2 $: Date Code date code date code date code Aug. 1, 2017 1st A 11th L 21st W 2nd B 12th M 22nd X 3rd C 13th N 23rd Y 4th D 14th P 24th Z 5th E 15th Q 25th a 6th F 16th R 26th b 7th G 17th S 27th c 8th H 18th T 28th d 9th J 19th U 29th e 10th K 20th V 30th f 31st g 5/7 SAW FILTER FOR UMTS Band2 Rx Murata part number : SAFFB1G96FN0F0A
Important notice Please make sure that your product has been evaluated and confirmed from the aspect of the fitness for the specifications of our product when our product is mounted to your product. All the items and parameters in this product specification/datasheet/catalog have been prescribed on the premise that our product is used for the purpose, under the condition and in the environment specified in this specification. You are requested not to use our product deviating from the condition and the environment specified in this specification. Please note that the only warranty that we provide regarding the products is its conformance to the specifications provided herein. Accordingly, we shall not be responsible for any defects in products or equipment incorporating such products, which are caused under the conditions other than those specified in this specification. WE HEREBY DISCLAIM ALL OTHER WARRANTIES REGARDING THE PRODUCTS, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION ANY WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, THAT THEY ARE DEFECT-FREE, OR AGAINST INFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS. The product shall not be used in any application listed below which requires especially high reliability for the prevention of such defect as may directly cause damage to the third party's life, body or property. You acknowledge and agree that, if you use our products in such applications, we will not be responsible for any failure to meet such requirements. Furthermore, YOU AGREE TO INDEMNIFY AND DEFEND US AND OUR AFFILIATES AGAINST ALL CLAIMS, DAMAGES, COSTS, AND EXPENSES THAT MAY BE INCURRED, INCLUDING WITHOUT LIMITATION, ATTORNEY FEES AND COSTS, DUE TO THE USE OF OUR PRODUCTS IN SUCH APPLICATIONS. - Aircraft equipment - Aerospace equipment - Undersea equipment - Power plant control equipment - Medical equipment - Transportation equipment (vehicles, trains, ships, elevator, etc.9 - Traffic signal equipment - Disaster prevention / crime prevention equipment - Burning / explosion control equipment - Application of similar complexity and/ or reliability requirements to the applications listed in the above We expressly prohibit you from analyzing, breaking, Reverse-Engineering, remodeling altering, and reproducing our product. Our product cannot be used for the product which is prohibited from being manufactured, used, and sold by the regulations and laws in the world. Please do not use the product in molding condition This product is ESD (ElectroStatic Discharge9 sensitive device. When you install or measure this, you should be careful not to add antistatic electricity or high voltage. Please be advised that you had better check anti serge voltage. We do not warrant or represent that any license, either express or implied, is granted under any our patent right, copyright, mask work right, or our other intellectual property right relating to any combination, machine, or process in which our products or services are used. Information provided by us regarding third-party products or services does not constitute a license from us to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from us under our patents or other intellectual property. Aug. 1, 2017 6/7 SAW FILTER FOR UMTS Band2 Rx Murata part number : SAFFB1G96FN0F0A Please do not use our products, our technical information and other data provided by us for the purpose of developing of mass-destruction weapons and the purpose of military use. Moreover, you must comply with "foreign exchange and foreign trade law", the "U.S. export administration regulations", etc. Please note that we may discontinue the manufacture of our products, due to reasons such as end of supply of materials and/or components from our suppliers. Customer acknowledges that Murata will, if requested by you, conduct a failure analysis for defect or alleged defect of Products only at the level required for consumer grade Products, and thus such analysis may not always be available or be in accordance with your request (for example, in cases where the defect was caused by components in Products supplied to Murata from a third party9. By signing on specification sheet or approval sheet, you acknowledge that you are the legal representative for your company and that you understand and accept the validity of the contents herein. When you are not able to return the signed version of specification sheet or approval sheet within 90 days from receiving date of specification sheet or approval sheet, it shall be deemed to be your consent on the content of specification sheet or approval sheet. The product shall not be used in any other application/model than that of claimed to Murata. Customer acknowledges that engineering samples may deviate from specifications and may contain defects due to their development status. We reject any liability or product warranty for engineering samples. In particular we disclaim liability for damages caused by • the use of the engineering sample other than for evaluation purposes, particularly the installation or integration in the product to be sold by you, • deviation or lapse in function of engineering sample, • improper use of engineering samples. We disclaim any liability for consequential and incidental damages. If you cannot agree the above contents, you should inquire our sales. Aug. 1, 2017 7/7