DPH-102-M5-C5

753 FIBER SENSORS Head-separated Dual Display Digital Pressure Sensor For Gas DPC-100 SERIES DPH-100 SERIES Related Information ■■General terms and conditions.............. F-3 ■■Glossary of terms........................ P.1563~ ■■Selection guide.............................. P.699~ ■■General precautions...................... P.1566 LASER SENSORS PHOTOELECTRIC SENSORS Recognition MICRO PHOTOELECTRIC SENSORS AREA SENSORS SAFETY LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS * Passed the UL 991 Environment Test PARTICULAR USE SENSORS * UL 61010C-1 compatible, Passed the UL 991 Environment Test based on SEMI S2-0200. [Category applicable for semiconductor manufacturing: TWW2, Process Equipment] [Applicable standards: UL 61010C-1] [Additional test / evaluation standards as per intended use: UL 991, SEMI S2-0200] SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS MEASUREMENT SENSORS STATIC CONTROL DEVICES LASER MARKERS PLC HUMAN MACHINE INTERFACES ENERGY MANAGEMENT SOLUTIONS FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS panasonic.net/id/pidsx/global Digital Auto reference With analog output Single axis type Direct installation using a hexagonal wrench Breakthrough construction Flexible design! Sensor heads can be embedded New concept Obstructions can be avoided and installation from above can be done much more easily using a hexagonal wrench. This also eliminates wasted installation space and contributes to a smaller installation footprint. Because the bolts can be turned from directly above, embedding the sensor heads into narrow spaces is possible. In addition, the flat installation leaves no worries for danger of objects striking against the sensor and damaging it. Previous problem Spanner is difficult to hold! DPH-100 (Obstructed by floor surface) Turns minimally from above! Selection Guide Pressure/ Digital Display Pressure/ Head-separated Flow DPC-L100/ DPH-L100 DPS-400/ DPH-100 DPC-100/ DPH-100 Previous problem Obstacle Previous problem Spanner cannot be turned! Previous problem Large space needed to turn the spanner! Projection sticks out after installation. Easy to knock against objects. DPH-100 Embedded installation greatly increases design flexibility! Quick maintenance During maintenance, the sensor head needed to be removed can be easily removed from directly above. DPH-100 Conventional models Remove and install the required sensor head directly. Spanner does not fit! It cannot be turned either! To remove , you have to remove the sensors in order starting from . Head-separated Dual Display Digital Pressure Sensor DPC-100 SERIES DPH-100 SERIES APPLICATIONS 754 FIBER SENSORS Confirming vacuum breakdown Confirming reference pressure Air-leak test LASER SENSORS PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS AREA SENSORS SAFETY LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS Mounting space-saving Easy adjustment Space saving during installation Sensor heads can be turned after installation Conventional models Saved space DPH-10□-M3 DPH-10□-M5 SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS MEASUREMENT SENSORS 14 mm 0.551 in Wasted space SENSOR OPTIONS STATIC CONTROL DEVICES Conventional models 12.5 mm 0.492 in Free-turning 75 mm 2.953 in After installation, you can alter the cable direction with the pressure port still secured in place. In addition, the cable does not get twisted during installation. Independent use of sensor head possible Separate analog voltage output for each sensor head DPH-100 LASER MARKERS PLC HUMAN MACHINE INTERFACES ENERGY MANAGEMENT SOLUTIONS FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS 10 mm 0.394 in 60 mm 2.362 in DOWN Analog 1 to 5 V Because the dead zone caused by the nut is eliminated, the narrowed-down thickness after installation contributes to space saving. The analog voltage output from the sensor head can be picked up directly. 3 types of pressure range For vacuum pressure For positive pressure For compound pressure 0 kPa 100 kPa Selection Guide Pressure/ Digital Display Pressure/ Head-separated Flow Sensor head line-up -100 kPa 12 to 24 V DC 20% 1 MPa Stainless steel pressure ports come in 3 shapes M3 male thread M5 male thread Stainless steel is strong and does not bend easily R1/8 male thread + M5 female thread DPC-L100/ DPH-L100 DPS-400/ DPH-100 DPC-100/ DPH-100 755 FIBER SENSORS LASER SENSORS PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS Head-separated Dual Display Digital Pressure Sensor DPC-100 SERIES DPH-100 SERIES Dual display + Direct setting Current value Equipped with a 30 mm 1.181 in square compact-sized dual display. “Current value” and “Threshold value” can be checked at the same time. The threshold value can be changed in RUN mode directly. AREA SENSORS Main display Threshold value Sub display The current value and the threshold value can be checked simultaneously! SAFETY LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS Because direct setting is possible Operation is as easy as analog PARTICULAR USE SENSORS SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS Dual display direct setting Previous problem Difficulty with only one display Just press the button Operation 1 Operation 2 Operation 3 Operation 4 Press the MODE key Adjust the threshold value Return to RUN mode while in RUN mode MEASUREMENT SENSORS STATIC CONTROL DEVICES LASER MARKERS –91.8 Write down current value 1/4 of the operations PLC HUMAN MACHINE INTERFACES ENERGY MANAGEMENT SOLUTIONS FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS Selection Guide Pressure/ Digital Display Pressure/ Head-separated Flow DPC-L100/ DPH-L100 DPS-400/ DPH-100 DPC-100/ DPH-100 High-speed response time at 500 μs Reduced tact time. Response time contributes to even greater productivity. Response time at 500 μs The controller’s setting operation mode has a 3-level configuration to suit the frequency of use The setting levels are clearly separated into “RUN mode” for operation settings that are carried out daily, “MENU SETTING mode” for basic settings, and “PRO mode” for special and detailed setting. These make setting operations easy to understand and easy to carry out. Simple setting RUN mode MENU SETTING mode PRO mode Special and detailed setting RUN mode Settings such as threshold value adjustment and key lock operation can be carried out while the sensor is operating. MENU SETTING mode Basic settings such as output mode setting and NO/NC switching can be carried out. PRO mode High-level function settings such as hysteresis adjustment and the copy function can be carried out. Head-separated Dual Display Digital Pressure Sensor DPC-100 SERIES DPH-100 SERIES 3-color display lets you view the controller status at a glance FIBER SENSORS The main display color switches between green and red in accordance with the ON/OFF status of output during RUN mode. In addition, the display always appears orange while setting is in progress, so that the status of the controller can be viewed at a glance. RUN While setting is in progress RUN mode PRO mode SAFETY LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS Copy function reduces man-hours and human error Controllers can be connected to a master controller one by one, and a copy of the setting details for the master controller can be transmitted as data to the slave controllers. If making the same settings for multiple controllers, this prevents setting errors from occurring with the other controllers and also reduces the number of changes required to instruction manuals when equipment designs are changed. Copying via wiring Master controller Power supply +V +V 0V 0V Comparative output 1 Comparative output 1 External input External input Details transmitted Slave controller PARTICULAR USE SENSORS SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS Details received Det ails * Other wires are not connected. PHOTOELECTRIC SENSORS AREA SENSORS Orange while setting is in progress. or LASER SENSORS MICRO PHOTOELECTRIC SENSORS MENU SETTING mode Display in red or green depending on output ON/ OFF. 756 cop ied MEASUREMENT SENSORS STATIC CONTROL DEVICES LASER MARKERS PLC HUMAN MACHINE INTERFACES ENERGY MANAGEMENT SOLUTIONS FA COMPONENTS Sensor head auto-recognition The controller will automatically recognize sensor heads when they are connected, even for sensor heads with different rated pressure ranges. There is no need to use the controller to change settings. DPH-101□ Compound pressure DPH-102□ Positive pressure +1 MPa DPH-103□ Vacuum pressure –101 kPa Auto-recognition Selection Guide Pressure/ Digital Display Pressure/ Head-separated Initial setting not needed Flow DPC-100 original functions Inputs Outputs Comparative output 1 Auto-reference input UV CURING SYSTEMS ±100 kPa 1 model to suit a wide variety of applications Remote zero-adjustment input MACHINE VISION SYSTEMS Comparative output 2 Selection Selection Analog voltage output 1 to 5 V Analog current output 4 to 20 mA DPC-L100/ DPH-L100 DPS-400/ DPH-100 DPC-100/ DPH-100 757 Head-separated Dual Display Digital Pressure Sensor DPC-100 SERIES DPH-100 SERIES Comparative output 1 EASY mode PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS Comparative output 2 EASY mode Vacuum breakdown can also be checked during suction applications! Comparative output 1 EASY mode SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS MEASUREMENT SENSORS STATIC CONTROL DEVICES LASER MARKERS PLC HUMAN MACHINE INTERFACES ENERGY MANAGEMENT SOLUTIONS Comparative output 2 EASY mode 1 Reference pressure alarm output is possible during reference pressure checking! ON Comparative output 1 hysteresis mode Suction checking OFF ON OFF EASY mode Comparative output 2 EASY mode Vacuum breakdown checking –100 kPa P-1 0 kPa P-2 Hysteresis mode 2 3 This mode is used for setting comparative output hysteresis to theReference desired level and for carrying out ON/ ON OFF control. H (Hysteresis) pressure Comparative output 1 P hysteresis mode 0 Comparative ON output OFF H: Fixed Comparative output 2 EASY mode ON Hi Lo Alarm output 0 Comparative ON output OFF OFF Alarm output ON OFF H (Hysteresis) H: 1 digit or more Notes: 1) Hysteresis can be fixed to one of eight different levels. OFF 2) “ ” appears in the sub display for Note: “ ” or “ ” appears in the sub display for comparative output 1, and “ ” appears for0 kPa Lo-1 Hi-1 P-2 comparative output 1, and “ ” or “ ” comparative output 2. appears for comparative output 2. If the reference pressure of the device changes, the autoreference function partially shift the comparative output judgment level by the amount that the reference pressure shifts, and the remote zero-adjustment function can reset the display value to zero via external input. These functions are ideal for places where the reference pressure fluctuates wildly, or where fine settings are desired. H (Hysteresis) Hi H (Hysteresis) Lo 0 Comparative ON output OFF H: Fixed Notes: 1) Hysteresis can be fixed to one of eight different levels. 2) “ ” or “ ” appears in the sub display for comparative output 1, and “ ” or “ ” appears for comparative output 2. Without auto-reference and remote zero-adjustment functions Comparative output: Window comparator mode Hi-1… 30, Lo-1… 25 Fixed set value 40 NG? 30 Leak threshold level 20 Variation in the filling pressure Pressure 0 OK NG? 15 UV CURING SYSTEMS DPC-L100/ DPH-L100 DPS-400/ DPH-100 DPC-100/ DPH-100 P-2 Window comparator mode 25 MACHINE VISION SYSTEMS Flow Hi-1 Equipped with auto-reference/remote zero-adjustment functions, More precise pressure management is possible with a minimum of effort FA COMPONENTS Selection Guide Pressure/ Digital Display Pressure/ Head-separated Lo-1 This mode is used for setting comparative output ON and OFF at pressures within the setting range. checking OFF Reference pressure checking ON 0 kPa This mode is used for comparative output ON/OFF control. Pressure PARTICULAR USE SENSORS ON Equipped with two independent comparative outputs, and separate sensing modes can be for each of them. Vacuum breakdown checking Two comparative outputs are provided, so that one of the outputs can be used as a warning output. In addition, if an –100 kPa P-1 0 kPa P-2 output is not being used, it can be disabled. AREA SENSORS SAFETY LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS Suction checking OFF OFF selected Pressure LASER SENSORS Equipped with independent two output and three output modes Pressure FIBER SENSORS ON Trial 1 Trial 2 Trial 3 Time Because the threshold level is fixed for conventional pressure sensors, changes in the reference pressure result in wrong decisions. With auto-reference function applied Sets the absolute threshold level Auto-reference input With remote zero-adjustment function applied Comparative output: Window comparator mode Hi-1… 0, Lo-1… –5 Comparative output: Window comparator mode Hi-1… 0, Lo-1… –5 Sets the absolute threshold level Remote zero-adjustment input The display is forced to “0”, and only the filling pressure drop range is displayed. The display remains at “30” and only the threshold level is changed. 30 30 OK 25 20 Threshold level after applying auto-reference input 15 0 –5 25 20 OK Threshold level after applying remote zero-adjustment input 15 Threshold level before applying remote zero-adjustment input Threshold level before applying auto-reference input Trial 1 Pressure 0 -5 Trial 1 Pressure 0 Time Auto-reference input value… When auto-reference input is applied, the reference pressure “30” is added to the threshold level. If the reference pressure changes to “20” or “40”, the auto-reference input compensates for this every time by changing the threshold level, so any variation in the filling pressure can be ignored. -5 Time Displayed when remote zeroadjustment input is applied… When remote zero-adjustment input is applied, the reference pressure is forced to “0”. If the reference pressure changes to “20” or “40”, the remote zero-adjustment input adjusts the reference pressure to “0” every time the reference pressure changes, so any variation in the filling pressure can be ignored. Head-separated Dual Display Digital Pressure Sensor DPC-100 SERIES DPH-100 SERIES Sub display can be customized Setting details can be understood at a glance The sub display can be set to indicate any other desired values or letters apart from the threshold value. This eliminates the need for tasks such as affixing a label to the device to indicate the normal pressure value. The DPC-100 setting details appear in the digital display. Because the settings are in numeric form that can be easily understood, it is useful for times such as when receiving technical support by telephone. 2nd digit: Setting status for comparative output 2 Indicates desired values and letters 1st digit: Setting status for comparative output 1 5th digit: D  isplay color setting 6th digit: R  esponse time setting Tight installation to panels is possible An exclusive mounting bracket (MS-DP1-2) that is suitable for 1 to 6 mm 0.039 to 0.236 in panel thickness is available. FIBER SENSORS LASER SENSORS PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS 3rd digit: Threshold value display and analog output setting 4th digit: External input setting AREA SENSORS SAFETY LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS 8th digit: D  isplay speed and ECO mode setting SENSOR OPTIONS 7th digit: U  nit switching setting An exclusive mounting bracket (MS-DP1-6) that supports tight installation is available Space saving can also be obtained if an L-shaped mounting bracket is used. Tight installation is possibl Tight installation is possible 758 e SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS MEASUREMENT SENSORS STATIC CONTROL DEVICES LASER MARKERS PLC Ceiling mounting HUMAN MACHINE INTERFACES Floor mounting ENERGY MANAGEMENT SOLUTIONS Power supply cable can be connected with one-touch connection Takes up much less space The accessory connector attached cable (2 m 6.562 ft) can be connected easily with one-touch connection. FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS Connection cable* To power supply e-CON Selection Guide Pressure/ Digital Display Pressure/ Head-separated Flow To sensor head * Options: 5 m 16.404 ft type is also available. Types without connector attached DPC-10□-J cable are also available Front protection cover available MS-DP1-3 Commercially-available connectors can be used for cable connections. Only the required length of cable needs to be used, which contributes to a reduced amount of wastage for unneeded cable. Environmentally friendly A single mounting hole! * Refer to p.760 for recommended commercially-available connectors. DPC-L100/ DPH-L100 DPS-400/ DPH-100 DPC-100/ DPH-100 759 FIBER SENSORS Head-separated Dual Display Digital Pressure Sensor DPC-100 SERIES DPH-100 SERIES PRODUCT CONFIGURATION LASER SENSORS Connector (e-CON) Sensor head PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS AREA SENSORS SAFETY LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS Sensor heads PARTICULAR USE SENSORS Type SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS MEASUREMENT SENSORS STATIC CONTROL DEVICES LASER MARKERS Appearance Compound pressure ENERGY MANAGEMENT SOLUTIONS FA COMPONENTS Rated pressure range DPH-10□-M3(-R) –100.0 to +100.0 kPa Bendingresistant cable DPH-10□-M5(-R) Positive pressure 0 to +1.000 MPa Bendingresistant cable PLC HUMAN MACHINE INTERFACES Connector attached cable ORDER GUIDE INDUCTIVE PROXIMITY SENSORS SENSOR OPTIONS Power supply connector Controller Vacuum pressure DPH-10□(-R) 0 to –101.0 kPa Bendingresistant cable MACHINE VISION SYSTEMS Note: The bending-resistant cable type of DPH-102 is not available. UV CURING SYSTEMS 5 m 16.404 ft cable length type Model No. Pressure port DPH-101 R1/8 male thread + M5 female thread DPH-101-M3 M3 male thread DPH-101-M5 M5 male thread DPH-101-R R1/8 male thread + M5 female thread DPH-101-M3-R M3 male thread DPH-101-M5-R M5 male thread DPH-102 (Note) R1/8 male thread + M5 female thread DPH-102-M5 M5 male thread DPH-102-M5-R M5 male thread DPH-103 R1/8 male thread + M5 female thread DPH-103-M3 M3 male thread DPH-103-M5 M5 male thread DPH-103-R R1/8 male thread + M5 female thread DPH-103-M3-R M3 male thread DPH-103-M5-R M5 male thread Applicable fluid Air, non-corrosive gas 5 m 16.404 ft cable length type (standard: 2 m 6.562 ft) is also available. When ordering this type, suffix“-C5” to the Model No. (e.g.) 5 m 16.404 ft cable length type of DPH-103-M5-R is “DPH-103-M5-R-C5” Controllers Selection Guide Pressure/ Digital Display Appearance Rated pressure range Model No. Comparative output Pressure/ Head-separated Flow DPC-L100/ DPH-L100 DPS-400/ DPH-100 DPC-100/ DPH-100 * CN-66A-C2 (Connector attached cable 2 m 6.562 ft) is attached. Compound pressure: –100.0 to +100.0 kPa Positive pressure: 0 to +1.000 MPa Vacuum pressure: 0 to –101.0 kPa DPC-101 NPN open-collector transistor DPC-101-P PNP open-collector transistor Type without connector attached cable Type without connector attached cable CN-66A-C2 is available. When ordering this type, suffix “-J” to the Model No. (e.g) Type without connector attached cable of DPC-101-P is “DPC-101-P-J” Accessory • CN-66A-C2 (Connector attached cable 2 m 6.562 ft) Head-separated Dual Display Digital Pressure Sensor DPC-100 SERIES DPH-100 SERIES OPTIONS FIBER SENSORS Designation Sensor head connector (e-CON) Connector attached cable 760 Model No. CN-EP2 (Note 1) 5 pcs. per set Sensor head connector (e-CON) Description • CN-EP2 PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS Connector for connecting sensor head controller power supply / I-O cable. CN-66A-C2 (Note 2) Length 2 m 6.562 ft Controller 2 CN-66A-C5 LASER SENSORS 0.2 mm 6-core oil-resistant cabtyre cable Length 5 m 16.404 ft with connector Note: O  ne is attached to each sensor head according to standard. AREA SENSORS SAFETY LIGHT CURTAINS / SAFETY COMPONENTS Power supply connector CN-66A Controller mounting bracket MS-DP1-6 Allows sensors to be installed on the wall. Multiple sensors can also be mounted closely. Panel mounting bracket MS-DP1-2 Allows installation to panels with thickness of 1 to 6 mm 0.039 to 0.236 in. Multiple sensors can also be mounted closely. PARTICULAR USE SENSORS Front protection cover MS-DP1-3 Protects the adjustment surfaces of controllers. (Can be attached when using the panel mounting bracket) SENSOR OPTIONS Notes: 1) One is attached to each sensor head according to standard. 2) The connector attached cable CN-66A-C2 is supplied with the controller according to standard. SIMPLE WIRE-SAVING UNITS 5 pcs. per set Connector for controller power supply / I-O cable. Connector attached cable • CN-66A-C2 • CN-66A-C5 Note: The connector attached cable CN-66A-C2 is supplied with the controller according to standard. Power supply connector • CN-66A Controller mounting bracket • MS-DP1-6 M3 (length 6 mm 0.236 in) screws with washers Accessory for MS-DP1-6 ( Connector pin Housing ) Panel mounting bracket, Front protection cover • MS-DP1-2 • MS-DP1-3 INDUCTIVE PROXIMITY SENSORS WIRE-SAVING SYSTEMS MEASUREMENT SENSORS STATIC CONTROL DEVICES LASER MARKERS PLC Front protection cover MS-DP1-3 Controller mounting bracket MS-DP1-6 (Optional) PRESSURE / FLOW SENSORS HUMAN MACHINE INTERFACES ENERGY MANAGEMENT SOLUTIONS Panel mounting bracket MS-DP1-2 FA COMPONENTS MACHINE VISION SYSTEMS Recommended e-CON UV CURING SYSTEMS Model No.: 1473562-4 (Manufactured by Tyco Electronics Japan G.K.) Note: Contact the manufacturer for details of the recommended products. Recommended power supply connector Contact: SPHD-001T-P0.5, Housing: PAP-06V-S (Manufactured by J.S.T. Mfg.Co., Ltd.) Note: Contact the manufacturer for details of the recommended products. Recommended crimping tool Model No.: YC-610R (Manufactured by J.S.T. Mfg. Co., Ltd.) Note: Contact the manufacturer for details of the recommended products. Selection Guide Pressure/ Digital Display Pressure/ Head-separated Flow DPC-L100/ DPH-L100 DPS-400/ DPH-100 DPC-100/ DPH-100 761 Head-separated Dual Display Digital Pressure Sensor SPECIFICATIONS FIBER SENSORS Sensor heads PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS AREA SENSORS SAFETY LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS Type Item PLC –101 kPa type Rated pressure range Pressure withstandability DPH-102 DPH-102-M5(-R) DPH-103(-R) DPH-103-M3(-R) DPH-103-M5(-R) EMC Directive, RoHS Directive Type of pressure Gauge pressure –100.0 to +100.0 kPa 0 to +1.000 MPa 0 to –101.0 kPa 500 kPa 1.5 MPa 500 kPa Applicable fluid Air, non-corrosive gas Supply voltage 12 to 24 V DC ±10 %   Ripple P-P 10 % or less Current consumption Analog voltage output Environmental resistance LASER MARKERS Vacuum pressure 1 MPa type CE marking directive compliance WIRE-SAVING SYSTEMS STATIC CONTROL DEVICES Positive pressure ±100 kPa type Model No.(Note 3) DPH-101(-R) DPH-101-M3(-R) DPH-101-M5(-R) SIMPLE WIRE-SAVING UNITS MEASUREMENT SENSORS Compound pressure Protection Ambient temperature Ambient humidity Voltage withstandability 15 mA or less Output voltage: 1 to 5 V (over rated pressure range) Zero point: within 1 V ±2.5 % F.S. (vacuum / positive pressure type) within 3 V ±3 % F.S. (compound pressure type) Span: within 4 V ±3.5 % F.S. Linearity: within ±0.5 % F.S. Output impedance: 1 kΩ approx. 5 Output voltage (V) LASER SENSORS DPC-100 SERIES DPH-100 SERIES 3 1 Pressure High pressure (positive / compound pressure type) High vacuum (vacuum pressure type) IP40 (IEC) 0 to +50 °C +32 to +122 °F (No dew condensation allowed), Storage: –10 to +60 °C +14 to +140 °F 35 to 85 % RH, Storage: 35 to 85 % RH 1,000 V AC for one min. between all supply terminals connected together and enclosure Insulation resistance 50 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure Vibration resistance 10 to 500 Hz frequency, double amplitude 3 mm 0.118 in or maximum acceleration 196 m/s2, in X, Y and Z directions for two hours each Shock resistance 1,000 m/s2 acceleration (100 G approx.) in X, Y and Z directions three times each HUMAN MACHINE INTERFACES Temperature characteristics Over ambient temperature range 0 to +50 °C +32 to +122 °F: within ±2 % F.S. of detected pressure at +25 °C +77 °F ENERGY MANAGEMENT SOLUTIONS Pressure port FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS Connecting method Pressure/ Head-separated Flow DPC-L100/ DPH-L100 DPS-400/ DPH-100 DPC-100/ DPH-100 Connector 0.2 mm2 4-core oil resistant cabtyre cable (Models with “-R” affixed to the Model No. have flexible, oil-resistant cabtyre cable) Cable Cable extension Accessory Pressure/ Digital Display Front case: PBT, Rear case: PBT (glass fiber reinforced), Pressure port: Stainless steel (SUS303), O-ring: NBR Pressure element: Silicon diaphragm, PPS Material Weight Selection Guide DPH-10□(-R): R1/8 male thread + M5 female thread, DPH-10□-M3(-R): M3 male thread (for installing gasket) DPH-10□-M5(-R): M5 male thread (for installing gasket) Net weight Gross weight Extension up to total 10 m 32.808 ft is possible with 0.2 mm2, or more, cable. DPH-10□(-R): Head 10 g approx. / Cable 40 g approx., DPH-10□-M3/M5(-R): Head 6 g approx. / Cable 40 g approx. DPH-10□(-R): 80 g approx., DPH-10□-M3/M5(-R): 70 g approx. Connector (e-CON): 1 pc. Notes: 1) Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +25 °C +77 °F. 2) The sensor head can be used independently. 3) Model No. having the suffix “-R” is bending-resistant cable type. The bending-resistant cable type of DPH-102 is not available. Head-separated Dual Display Digital Pressure Sensor DPC-100 SERIES DPH-100 SERIES SPECIFICATIONS FIBER SENSORS Controllers LASER SENSORS Type Model No. Item CE marking directive compliance Applicable sensor head Rated pressure range (Note 2) Set pressure range (Note 2) Supply voltage Power consumption NPN output type PNP output type DPC-101 DPC-101-P EMC Directive, RoHS Directive DPH-101□, DPH-102□, DPH-103□ Compound pressure: –100.0 to +100.0 kPa, Positive pressure: 0 to +1.000 MPa, Vacuum pressure: 0 to –101.0 kPa Compound pressure: –199.9 to +199.9 kPa (–1.999 to +1.999 kgf/cm2, –19.98 to +19.98 psi, –1.999 to +1.999 bar, –1510 to +1537 mmHg, –59.4 to +60.5 inHg) Positive pressure: –1.050 to +1.050 MPa (–10.71 to +10.71 kgf/cm2, –152.2 to +152.2 psi, –10.50 to +10.50 bar) Vacuum pressure: +101.3 to –101.3 kPa (+1.033 to –1.033 kgf/cm2, +14.70 to –14.70 psi, +1.013 to –1.013 bar, +760 to –760 mmHg, +29.9 to –29.9 inHg) 12 to 24 V DC ±10 % Ripple P-P 10 % or less Normal operation: 960 mW or less (Current consumption 40 mA or less at 24 V supply voltage) ECO mode (STD): 720 mW or less (Current consumption 30 mA or less at 24 V supply voltage) ECO mode (FULL): 600 mW or less (Current consumption 25 mA or less at 24 V supply voltage) Excluding the current consumption of sensor head and analog output current Sensor head supply voltage Comparative outputs (Comparative output 1, 2) Output operation Output modes Hysteresis Repeatability Response time Same as supply voltage NPN open-collector transistor (2 outputs) • Maximum sink current: 100 mA • Applied voltage: 30 V DC or less (between comparative output and 0 V) • Residual voltage: 2 V or less (at 100 mA sink current) Analog output Inputs Sensor head input External input Auto-reference function/ Remote zero-adjustment function Display Displayable pressure range PNP open-collector transistor (2 outputs) • Maximum source current: 100 mA • Applied voltage: 30 V DC or less (between comparative output and +V) • Residual voltage: 2 V or less (at 100 mA source current) NO/NC, selectable by key operation EASY mode / Hysteresis mode / Window comparator mode Minimum 1 digit (variable) (however, 2 digits when using psi unit) With vacuum / positive pressure type connected: within ±0.2 % F.S. (±2 digits) With compound pressure type connected: within ±0.2 % F.S. (±4 digits) 0.5 ms, 1 ms, 2.5 ms, 5 ms, 10 ms, 25 ms, 50 ms, 100 ms, 250 ms, 500 ms, 1,000 ms, 5,000 ms, selectable by key operation Short-circuit protection Incorporated • Output current: 1 to 5 V DC • Zero point: within 1 V ±0.5 % F.S. (vacuum / positive pressure type) within 3 V ±0.5 % F.S. (compound pressure type) • Span: within 4 V ±0.5 % F.S. • Linearity: within ±0.1 % F.S. • Output impedance: 1 kΩ approx. • Output current: 4 to 20 mA • Zero point: within 4 mA ±1 % F.S. (vacuum / positive pressure type) within 12 mA ±1.5 % F.S. (compound pressure type) • Span: within 16 mA ±1.5 % F.S. • Linearity: within ±0.1 % F.S. • Load resistance: 250 Ω (max.) Input voltage range: 1 to 5 V DC (over rated pressure range) ON voltage: 0.4 V DC or less OFF voltage: 5 to 30 V DC, or open Input impedance: 10 kΩ approx. Input time: 1 ms or more ON voltage: 5 V to +V DC OFF voltage: 0.6 V DC or less, or open Input impedance: 10 kΩ approx. Input time: 1 ms or more IP40 (IEC) Environmental resistance Orange LED (Comparative output 1 operation indicator, comparative output 2 operation indicator: Lights up when each comparative output is ON ) Ambient humidity Voltage withstandability –10 to +50 °C +14 to +122 °F (No dew condensation or icing allowed), Storage: –10 to +60 °C +14 to +140 °F 35 to 85 % RH, Storage: 35 to 85 % RH 1,000 V AC for one min. between all supply terminals connected together and enclosure Insulation resistance 50 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure Vibration resistance 10 to 500 Hz frequency, double amplitude 3 mm 0.118 in or maximum acceleration 196 m/s2, in X, Y and Z directions for two hours each (when panel mounting bracket is mounted : 10 to 150 Hz frequency, double amplitude 0.75 mm 0.030 in or maximum acceleration 49 m/s2, in X, Y and Z directions for two hours each) Shock resistance Temperature characteristics Material Connecting method Weight Accessories MICRO PHOTOELECTRIC SENSORS AREA SENSORS SAFETY LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS MEASUREMENT SENSORS STATIC CONTROL DEVICES LASER MARKERS PLC HUMAN MACHINE INTERFACES ENERGY MANAGEMENT SOLUTIONS FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS 4 digits + 4 digits 3-color LCD display (Display refresh rate: 250 ms, 500 ms, 1,000 ms, selectable by key operation) Protection Ambient temperature PHOTOELECTRIC SENSORS Vacuum pressure: +5.1 to –101.3 kPa, Positive pressure: –0.050 to +1.020 MPa, Compound pressure: –101.3 to +105.0 kPa Operation indicator Cable length 762 100 m/s2 acceleration (10 G approx.) in X, Y and Z directions three times each Within ±0.5 % F.S. (ambient temperature range based on +20 °C +68 °F) Enclosure: PBT (glass fiber reinforced), LCD display: Acrylic, Mounting threaded part: Brass (nickel plated), Switch part: Silicone rubber Connector Total length up to 100 m 328.084 ft is possible with 0.3 mm2, or more, cable. Net weight: 25 g approx. (excluding connector attached cable), Gross weight: 140 g approx. CN-66A-C2 (Connector attached cable 2 m 6.562 ft), Pressure unit label: 1 set Notes: 1) Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +20 °C +68 °F. 2) It changes automatically according to the connected pressure sensor head. 3) The values specified above are applied only to the controller. Selection Guide Pressure/ Digital Display Pressure/ Head-separated Flow DPC-L100/ DPH-L100 DPS-400/ DPH-100 DPC-100/ DPH-100 763 Head-separated Dual Display Digital Pressure Sensor I/O CIRCUIT AND WIRING DIAGRAMS FIBER SENSORS DPC-101 NPN output type I/O circuit diagram MICRO PHOTOELECTRIC SENSORS SAFETY LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS MEASUREMENT SENSORS STATIC CONTROL DEVICES D4 Color code of connector attached cable Model discrimination signal Analog voltage input 1 kΩ Z ZD3 0V Sensor head internal circuit For independent use of sensor head CN1 terminal No. +V Sensor head main circuit AREA SENSORS CN2 terminal No. Intermediate cable D1 (Brown) +V (Pink) External *1 input (Note1) (Gray) Analog voltage / current output (Note 2,3) (Black) Comparative output 1 10kΩ D 2 1 kΩ D3 Tr1 Tr2 Color code Load Load + 100 mA max. (White) Comparative output 2 ZD1 ZD2 (Blue) 0 V Controller internal circuit Terminal No. – 12 to 24 V DC ±10 % 100 mA max. Notes: 1) Select and use the auto-reference function and remote zero-adjustment function. 2) Set the output load resistance during analog current output to 250 Ω (max.) 3) Note that a voltage of 5 V or higher is generated during analog current output. Symbols … D1 to D4 : Reverse supply polarity protection diode ZD1 to ZD3 : Surge absorption zener diode Tr1, Tr2 : NPN output transistor *1 Non-voltage contact or NPN open-collector transistor or FA COMPONENTS High (5 to 30 V DC, or open): Invalid Low (0.4 V DC or less): Valid Terminal arrangement diagram 1 2 3 4 5 MACHINE VISION SYSTEMS 6 Connector for power supply / I-O cable connection Connector for power supply / I-O cable (CN1) Connector for sensor head connection Connector for sensor head (CN2) UV CURING SYSTEMS Selection Guide Pressure/ Digital Display Pressure/ Head-separated Flow DPC-L100/ DPH-L100 DPS-400/ DPH-100 DPC-100/ DPH-100 1 2 3 4 (Brown) +V 1 kΩ (White) Not connected (Note1) (Black) Analog + voltage output – (1 to 5 V) 12 to 24 V DC ±10 % ZD Sensor head internal circuit (Blue) 0 V Users’ circuit Notes: 1) In case the sensor head is used independently, insulate the white lead wire (terminal No.4) and keep it open. 2) When the sensor head is used independently, devices connected to the analog output must have an input impedance set at 50 kΩ or more. Symbols … D : R  everse supply polarity protection diode ZD : Surge absorption zener diode PLC ENERGY MANAGEMENT SOLUTIONS D Users’ circuit LASER MARKERS HUMAN MACHINE INTERFACES Sensor head main circuit PHOTOELECTRIC SENSORS Controller main circuit LASER SENSORS DPC-100 SERIES DPH-100 SERIES +V Analog voltage/current output 0V Comparative output 1 Comparative output 2 E xternal input (auto-reference function / remote zero-adjustment function) Sensor head power supply Analog voltage input 0V Model discrimination signal Head-separated Dual Display Digital Pressure Sensor DPC-100 SERIES DPH-100 SERIES I/O CIRCUIT AND WIRING DIAGRAMS FIBER SENSORS DPC-101-P PNP output type I/O circuit diagram CN2 terminal No. Color code of connector attached cable Analog voltage input 1 kΩ ZD3 0V Sensor head internal circuit (Pink) External input (Note1) (Black) Comparative output 1 D1 Tr1 10kΩ D2 ZD1 Tr2 Color code *1 100 mA max. (White) Comparative output 2 100 mA max. ZD2 (Gray) Analog voltage / current output (Note 2, 3) (Blue) 0 V 1 kΩ D3 Intermediate cable Terminal No. (Brown) +V Controller internal circuit + – 12 to 24 V DC ±10 % Load Load Sensor head main circuit Model discrimination signal Controller main circuit Sensor head main circuit D4 For independent use of sensor head CN1 terminal No. +V 764 D (Brown) +V 1 kΩ (White) Not connected (Note1) (Black) Analog + voltage output – (1 to 5 V) Notes: 1) Select and use the auto-reference function and remote zero-adjustment function. 2) Set the output load resistance during analog current output to 250 Ω (max.) 3) Note that a voltage of +5 V or higher is generated during analog current output. Symbols … D1 to D4 : Reverse supply polarity protection diode ZD1 to ZD3 : Surge absorption zener diode Tr1, Tr2 : PNP output transistor *1 Sensor head internal circuit MICRO PHOTOELECTRIC SENSORS SAFETY LIGHT CURTAINS / SAFETY COMPONENTS 12 to 24 V DC ±10 % (Blue) 0 V Users’ circuit Notes: 1) In case the sensor head is used independently, insulate the white lead wire (terminal No.4) and keep it open. 2) When the sensor head is used independently, devices connected to the analog output must have an input impedance set at 50 kΩ or more. Symbols … D : R  everse supply polarity protection diode ZD : Surge absorption zener diode Non-voltage contact or PNP open-collector transistor PHOTOELECTRIC SENSORS AREA SENSORS ZD Users’ circuit LASER SENSORS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS MEASUREMENT SENSORS STATIC CONTROL DEVICES LASER MARKERS or PLC High (5 to +V DC): Valid Low (0.6 V DC or less, or open): Invalid HUMAN MACHINE INTERFACES ENERGY MANAGEMENT SOLUTIONS Terminal arrangement diagram 1 2 3 4 5 6 Connector for power supply / I-O cable connection Connector for sensor head connection 1 2 3 4 Connector for power supply / I-O cable (CN1) +V Analog voltage/current output 0V Comparative output 1 Comparative output 2 E xternal input (auto-reference function / remote zero-adjustment function) FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS Selection Guide Connector for sensor head (CN2) Sensor head power supply Analog voltage input 0V Model discrimination signal Pressure/ Digital Display Pressure/ Head-separated Flow DPC-L100/ DPH-L100 DPS-400/ DPH-100 DPC-100/ DPH-100 765 FIBER SENSORS LASER SENSORS PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS AREA SENSORS SAFETY LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS Head-separated Dual Display Digital Pressure Sensor DPC-100 SERIES DPH-100 SERIES PRECAUTIONS FOR PROPER USE Refer to p.1566 for general precautions. • Never use this product as a sensing device for personnel protection. • In case of using sensing devices for personnel protection, use products which meet laws and standards, such as OSHA, ANSI or IEC etc., for personnel protection applicable in each region or country. • The DPH-100 series is designed for use with air and non-corrosive gas. It cannot be used with liquid or corrosive and inflammable gases. INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS Part description SIMPLE WIRE-SAVING UNITS LASER MARKERS PLC HUMAN MACHINE INTERFACES ENERGY MANAGEMENT SOLUTIONS FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS Selection Guide Pressure/ Digital Display Pressure/ Head-separated Flow DPC-L100/ DPH-L100 DPS-400/ DPH-100 DPC-100/ DPH-100 ( ) Controller mounting bracket MS-DP1-6 (Optional) Main display Output 1 operation indicator Output 2 operation indicator Sub display Front protection cover MS-DP1-3 (Optional) MEASUREMENT SENSORS STATIC CONTROL DEVICES M3 (length 6 mm 0.236 in) screws with washers Accessory for MS-DP1-6 • The MS-DP1-2 panel mounting bracket (optional) and the MS-DP1-3 front protection cover (optional) are also available. SENSOR OPTIONS WIRE-SAVING SYSTEMS Mounting • When tightening the controller to the controller mounting bracket MS-DP1-6 (optional), use a tightening torque of 0.5 N·m or less. Mode selection key Set value DOWN key Set value UP key Wiring • Make sure that the power supply is off while wiring. • Verify that the supply voltage variation is within the rating. • If power is supplied from a commercial switching regulator, ensure that the frame ground (F.G.) terminal of the power supply is connected to an actual ground. • In case noise generating equipment (switching regulator, inverter motor, etc.) is used in the vicinity of this sensor, connect the frame ground (F.G.) terminal of the equipment to an actual ground. • Do not run the wires together with high-voltage lines or power lines or put them in the same raceway. This can cause malfunction due to induction. • Incorrect wiring will cause problems with operation. Connection • Do not apply stress directly to the connection cable leader or to the connector. Connector attached cable (CN-66A-C□) Release lever Housing: PAP-06V-S [Manufactured by J.S.T Mfg. Co. Ltd.] Sensor head cable Release lever e-CON: 1473562-4 [Manufactured by Tyco Electronics Japan G.K.] Panel mounting bracket MS-DP1-2 (Optional) Piping • Use a hexagonal wrench to install sensor head. For the tightening torque, refer to the following diagram. If excessive tightening torque is applied, the pressure port of the sensor head or the M5 male screw of the commercial coupling will get damaged. In case of R1/8 male thread type, wrap sealing tape around the coupler when connecting to prevent leakage. Pressure port Hexagonal wrench (bolt width) R1/8 male thread 5 mm 0.197 in M3 male thread M5 male thread 3 mm 0.118 in Hexagonal wrench Tightening torque 9.8 N·m or less 0.8 N·m or less 1.5 N·m or less Others • Use within the rated pressure range. • Do not apply pressure exceeding the pressure withstandability value. The diaphragm will get damaged and correct operation shall not be maintained. • Do not use during the initial transient time (controller: 0.5 sec. approx, sensor head: 50 ms approx.) after the power supply is switched on. • Avoid dust, dirt, and steam. • Take care that the sensor does not come in direct contact with water, oil, grease, or organic solvents, such as, thinner, etc. • Do not insert wires, etc., into the pressure port. The diaphragm will get damaged and correct operation shall not be maintained. • Do not operate the keys with pointed or sharp objects. Head-separated Dual Display Digital Pressure Sensor DPC-100 SERIES DPH-100 SERIES PRECAUTIONS FOR PROPER USE RUN mode • This is the normal operating mode. Setting item Description 766 Refer to p.1566 for general precautions. PRO mode • If the mode selection key is pressed and held for 5 sec. in RUN mode, the mode will switch to PRO mode. • If the mode selection key is pressed while a setting is being made, the mode will switch to RUN mode. In this case, the settings that have been changed will be entered. FIBER SENSORS LASER SENSORS PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS Threshold value setting The threshold values for ON/OFF operation can be changed directly by pressing the increment key (UP) and the decrement key (DOWN). Zero-adjustment function This forces the pressure value display to be reset to zero when the pressure port is open on the atmospheric pressure side. Key lock function Stops key operations from being accepted. Sub display switching Peak hold / bottom hold function Displays the peak value and bottom value for fluctuating pressure. The peak value appears in the main display, and the bottom value appears in the sub display. Changes the information in the sub display during RUN mode operation to the current pressure unit, number and desired alphanumeric display. Display refresh rate switching Changes the display refresh rate for the pressure value displayed in the main display. INDUCTIVE PROXIMITY SENSORS Hysteresis fix value switching Sets the hysteresis for EASY mode and window comparator mode. (8 steps) PARTICULAR USE SENSORS Linked display color switching Allows the display color for the main display to be switched in line with the output operation for comparative output 1 or comparative output 2. SENSOR OPTIONS External input relation selection The setting contents set at the external input selection in MENU SETTING mode can be shifted to correspond to either comparative output 1, 2 or 1 / 2. ECO mode setting Allows power consumption to be reduced by dimming the display or turning it off. MEASUREMENT SENSORS Setting check code Allows the setting details to be checked via codes. (Refer to below) STATIC CONTROL DEVICES Setting copy mode Allows the setting details for the master controller to be copied to slave controllers. LASER MARKERS Reset setting Resets the settings to the factory settings. Description Comparative output 1 output mode setting Sets the output mode for comparative output 1. Comparative output 2 output mode setting Sets the output mode for comparative output 2. Analog voltage/current output selection Selects analog voltage output or analog current output. External input selection Selects auto-reference function, or remote zeroadjustment function. NO/NC selection Normally open (NO) or normally closed (NC) can be selected. Response time setting Display color switching for main display Unit switching Pressure unit can be changed. 1st digit Comparative output 1 output mode 2nd digit Comparative output 2 NO/NC NO/NC selection output mode selection EASY NO OFF NC EASY NO Hysteresis Sets the response time. The response time can be selected from 0.5 ms, 1 ms, 2.5 ms, 5 ms, 10 ms, 25 ms, 50 ms, 100 ms, 250 ms, 500 ms, 1,000 ms and 5,000 ms. Allows the color for the main display to be changed. The colors can be set to “red/green” or “green/ red” to correspond to ON/OFF output, or it can be fixed at “red” or “green” all the time. Description NC Hysteresis 3rd digit Analog output – NO NC NO Window comparator NO NC NC – – Window comparator NO – – – NC Threshold value 1 External input OFF – Comparative output 1 Analog Threshold value 2 voltage Threshold value 3 AutoComparative output 2 output reference Comparative output Threshold value 4 1/2 Threshold value 1 Analog current output – PRESSURE / FLOW SENSORS SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS HUMAN MACHINE INTERFACES 4th digit Threshold display SAFETY LIGHT CURTAINS / SAFETY COMPONENTS PLC Table of codes Comparative output 1 Comparative output 2 Threshold value 2 Remote zeroadjustment Comparative output Threshold value 3 ENERGY MANAGEMENT SOLUTIONS FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS 1/2 Threshold value 4 – – Selection Guide Pressure/ Digital Display Pressure/ Head-separated Flow Code Setting item Code MENU SETTING mode • If the mode selection key is pressed and held for 2 sec. in RUN mode, the mode will switch to MENU SETTING mode. • If the mode selection key is pressed while a setting is being made, the mode will switch to RUN mode. In this case, the settings that have been changed will be entered. Setting item AREA SENSORS 5th digit 6th digit Displayed color of Displayed color Response time the main display relation 7th digit Unit selection (Note) Comparative output 1 0.5 ms MPa Comparative output 2 1 ms kPa Comparative output 1 2.5 ms Red when ON Green when ON 8th digit Display refresh rate Eco mode OFF 250 ms kgf/cm2 STD FULL Comparative output 2 5 ms bar Comparative output 1 10 ms psi Comparative output 2 25 ms mmHg Comparative output 1 50 ms inHg Comparative output 2 100 ms – – – 250 ms – – – 500 ms – – – – – 1,000 ms – – – – – 5,000 ms – – – Always red Always green OFF 500 ms STD FULL OFF 1,000 ms STD FULL Note: W  hen positive pressure type of the pressure sensor head is connected to the controller for use inside Japan, “ ” (MPa) or “ ” (kPa) is displayed. When compound pressure type or vacuum pressure type is connected, only “ ” (kPa) is displayed. DPC-L100/ DPH-L100 DPS-400/ DPH-100 DPC-100/ DPH-100 767 FIBER SENSORS LASER SENSORS DIMENSIONS (Unit: mm in) DPH-10□-M3(-R) DPH-10□-M5(-R) Sensor head Hexagonal hole (bolt width 3 0.118, 3.5 0.138 deep) Hexagonal hole (bolt width 5 0.197, 4 0.157 deep) AREA SENSORS 4.8 0.189 23.4 0.921 SAFETY LIGHT CURTAINS / SAFETY COMPONENTS 6.6 0.260 ø8.3 ø0.327 13.2 0.520 INDUCTIVE PROXIMITY SENSORS 7.8 0.307 ø8.4 ø0.331 5 0.197 SIMPLE WIRE-SAVING UNITS 6.6 0.260 ø3.7 ø0.146 cable, 2 m 6.562 ft long Gasket A R 1/ 8 4.8 0.189 14 0.5 0.551 0.244 7 0.276 SENSOR OPTIONS WIRE-SAVING SYSTEMS 20.5 0.807 5 0.197 ø6.2 ø0.244 10 0.394 14 10 0.5510.394 9 0.354 PARTICULAR USE SENSORS Sensor head R5 R0.197 R6.6 R0.260 MICRO PHOTOELECTRIC SENSORS MEASUREMENT SENSORS The CAD data can be downloaded from our website. DPH-10□(-R) PHOTOELECTRIC SENSORS PRESSURE / FLOW SENSORS DPC-100 SERIES DPH-100 SERIES Head-separated Dual Display Digital Pressure Sensor ø3.7 ø0.146 cable, (2 m 6.562 ft / 5 m 16.404 ft long) M5 female thread DPH-10□-M3(-R): M3 male thread DPH-10□-M5(-R): M5 male thread Model No. A DPH-10□-M3(-R) 3 0.118 DPH-10□-M5(-R) 3.5 0.138 DPC-101(-P) Controller STATIC CONTROL DEVICES 15.8 0.622 LASER MARKERS 7.9 0.311 PLC HUMAN MACHINE INTERFACES ENERGY MANAGEMENT SOLUTIONS 30 1.181 25.6 1.008 FA COMPONENTS MACHINE VISION SYSTEMS 3.7 0.146 25.5 1.004 2-M3 female thread, 4 0.157 deep 8.9 0.350 6.4 0.252 20.2 30 0.795 1.181 UV CURING SYSTEMS 20 0.787 9.05 0.356 7.3 0.287 3.8 0.150 Selection Guide Pressure/ Digital Display 1.5 0.059 MS-DP1-6 Pressure/ Head-separated Controller mounting bracket (Optional) Assembly dimensions 9.5 0.374 Flow DPC-L100/ DPH-L100 DPS-400/ DPH-100 DPC-100/ DPH-100 18 0.709 (R) 14.5 0.571 4.2 0.165 21 0.827 4.2 0.165 (R) 14.5 0.571 21 0.827 9.5 25.5 0.374 1.004 20 0.787 2-ø3.5 ø0.138 mounting hole 2 0.079 34.3 30 1.350 1.181 10.5 0.413 ( 10 0.394 18 0.709 29.95 1.179 Material : Cold rolled carbon steel (SPCC) (Trivalent uni-chrome plated) Two M3 (length 6 mm 0.236 in) screws with washers are attached. 8.9 0.350 30 ( 1.181 ) ) 45 1.772 30 1.181 45 1.772 1.5 0.059 30 1.181 3.7 0.146 30 1.181 2 0.079 9.05 0.356 6.4 0.252 15.8 0.622 Head-separated Dual Display Digital Pressure Sensor DPC-100 SERIES DPH-100 SERIES DIMENSIONS (Unit: mm in) The CAD data can be downloaded from our website. MS-DP1-2 MS-DP1-3 Panel mounting bracket (Optional), Front protection cover (Optional) FIBER SENSORS LASER SENSORS PHOTOELECTRIC SENSORS Assembly dimensions MICRO PHOTOELECTRIC SENSORS Mounting drawing with DPC-101 Vertical mounting Horizontal mounting 15.8 0.622 AREA SENSORS 15.8 0.622 Panel mounting bracket Panel mounting bracket SAFETY LIGHT CURTAINS / SAFETY COMPONENTS Front protection cover Front protection cover 11 ( 0.433 ) ( 768 PRESSURE / FLOW SENSORS 11 ( 0.433 ) ) 39.3 1.547 34.5 1.358 7.2 0.283 18.3 0.720 ( ) 39.3 1.547 34.5 1.358 3.7 0.146 INDUCTIVE PROXIMITY SENSORS 18.3 0.720 7.2 0.283 PARTICULAR USE SENSORS 3.7 0.146 SENSOR OPTIONS 20 ( 0.787 ) 34.5 1.358 6.4 0.252 6 0.236 20 ( 0.787 ) 34.5 1.358 A 6.4 0.252 6 0.236 A SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS 8.7 0.343 33.4 1.315 24 0.945 8.7 0.343 50 1.969 33.4 1.315 Panel thickness dimension 1 to 6 0.039 to 0.236 LASER MARKERS 33.4 1.315 ( ) 52 2.047 max. PLC 9.05 0.356 M3 female thread, 4 0.157deep 52 2.047 max. 9.05 0.356 HUMAN MACHINE INTERFACES ( ) View A Material: Polyacetal (Panel mounting bracket) Polycarbonate (Front protection cover) ENERGY MANAGEMENT SOLUTIONS View A FA COMPONENTS MACHINE VISION SYSTEMS Panel cut-out dimensions When 1 unit is installed MEASUREMENT SENSORS STATIC CONTROL DEVICES 8.9 0.350 8.9 0.350 50 33.4 1.969 1.315 Panel thickness dimension 1 to 6 0.039 to 0.236 When “n” units are installed horizontally in series When “n” units are installed vertically in series −0 31−0.4 −0 1.220−0.016 31 1.220 × n + 3.5 0.138 × (n-1) −0 31−0.4 −0 1.220 −0.106 UV CURING SYSTEMS −0 −0 31−0.4 −0 1.220 −0.106 31−0.4 −0 1.220 −0.016 55 2.165 or more Selection Guide 31 1.220 × n + 3.5 0.138 × (n-1) Pressure/ Digital Display Pressure/ Head-separated Flow 55 2.165 or more Note: The panel thickness should be 1 to 6 mm 0.039 to 0.236 in. CN-66A-C2 CN-66A-C5 (0.3158 ) 35 (1.378 ) Note: The panel thickness should be 1 to 6 mm 0.039 to 0.236 in. Connector attached cable (Optional, CN-66A-C2 is attached to the controller) • Length L L ( 50 1.969 ø4.8 ø0.189 cable ) Model No. (0.3158 ) Length L CN-66A-C2 2,000 78.740 CN-66A-C5 5,000 196.850 DPC-L100/ DPH-L100 DPS-400/ DPH-100 DPC-100/ DPH-100