F721A107MR

SOLID TANTALUM ELECTROLYTIC CAPACITORS F72 Low Profile Conformal coated Chip F75 Maximum CV Conformal coated Chip Adapted to the RoHS directive (2002/95/EC). Specifications Item Per formance Characteristics Category --55 ~ + 125˚C (Rated temperature : + 85˚C) Temperature Range Capacitance Tolerance ± 20%, ± 10% (at 120Hz) F72 33~68µF Dissipation Factor 100µF~ (120Hz) 150µF 220µF~330µF 6%Max. 8%Max. 10%Max. 12%Max. 68~330µF 470µF 680µF 1000µF 1500µF 2200µF ~150µF ~220µF ~330µF ~470~1500µF ~2200µF F75 10%Max. 14%Max. 18%Max. 24%Max. 30%Max. 45%Max. 0.22Ω 0.20Ω 0.15Ω 0.12Ω 0.07Ω ESR (100kHz) 33µF 47µF 68µF 100µF~ 0.90Ω 0.80Ω 0.75Ω 0.70Ω F72 Type numbering system (Example : 10V 100µF) 1 2 3 4 5 6 7 8 9 10 1 1 Taping code (Refer to page 267 for details) Case code Capacitance tolerance Rated Capacitance Rated voltage Series • After 1 minute's application of rated voltage, leakage current at 20˚C is not more than 0.01CV or 0.5µA, whichever is greater. Leakage Current • After 1 minute's application of rated voltage, leakage current at 85˚C is not more than 0.1CV or 5µA, whichever is greater. F72 1A 107MR • After 1 minute's application of derated voltage, leakage current at 125˚C is not more than 0.125CV or 6.3µA, whichever is greater. Capacitance Change by Temperature +15% Max. (at +125˚C) +10% Max. (at +85˚C) --10% Max. (at --55˚C) At 40˚C, 90~95% R.H., For 500 hours (No voltage applied) Capacitance Change • • • • • • Within ±10% of initial value Dissipation Factor • • • • • • • • • • Initial specified value or less Leakage Current • • • • • • • • • • • Initial specified value or less At --55˚C / +125˚C, 30 minutes each, For 5 cycles, Capacitance Change • • • • • • Within ±5% of initial value Dissipation Factor • • • • • • • • • • Initial specified value or less Leakage Currentv • • • • • • • • • • Initial specified value or less Reflow at 260˚C for 10 seconds, Dipping Flow at 260˚C for 10 seconds Capacitance Change • • • • • • Within ±5% of initial value Dissipation Factor • • • • • • • • • • Initial specified value or less Leakage Current • • • • • • • • • • • • Initial specified value or less After application of surge in series with a 33Ω resistor at the rate of 30 seconds ON, 30 seconds OFF, for 1000 successive test cycles at 85˚C, capacitors meet the characteristics requirements listed below. Capacitance Change • • • • • • Within ±5% of initial value Dissipation Factor • • • • • • • • • • Initial specified value or less Leakage Current • • • • • • • • • • • • Initial specified value or less After 2000 hours' application of rated voltage at 85˚C, or derated voltage at 125˚C, capacitors meet the characteristic requirements listed below. Capacitance Change • • • • • • Within ±10% of initial value Dissipation Factor • • • • • • • • • • Initial specified value or less Leakage Current • • • • • • • • • • • • Initial specified value or less Damp Heat Drawing H A B D L W Temperature Cycles Resistance to Soldering Heat Solder electrode Dimensions Case code R L W H (mm) A B (D) (6.2) Surge∗ 7.2 ± 0.3 6.0 ± 0.3 1.2 ± 0.3 1.3 ± 0.4 3.8 ± 0.6 F75 1 2 3 4 5 6 7 8 9 10 D dimension only for reference Type numbering system (Example : 16V 150µF) 1 1 Taping code (Refer to page 267 for details) Case code Capacitance tolerance Rated Capacitance Rated voltage Series Endurance∗ F75 1C 157 MD Drawing H A B D L W Dimensions Case code C D R L W H A B (mm) After applying the pressure load of 5N for 10±1 seconds horizontally to the center of capacitor side body which has 5N (0.51kg • f) no electrode and has been soldered Shear Test For 10 ± 1 seconds beforehand on an aluminum substrate, there shall be found neither exfoliation nor its sign at the terminal electrode. Keeping a capacitor surface-mounted on a substrate upside down and supporting the substrate at both of the opposite bottom points 45mm apart from the center of the capacitor, the pressure strength is applied with 20 R230 Terminal Strength a specified jig at the center of the substrate so that the substrate may bend by 1mm as illustrated. Then, 45 45 there shall be found no remarkable abnormality on the capacitor terminals. ∗ As for the surge and derated voltage at 125˚C, refer to page 266 for details. (D) (6.0) (6.4) (6.2) 7.1 ± 0.3 3.2 ± 0.3 2.5 ± 0.3 1.3 ± 0.3 3.6 ± 0.6 7.3 ± 0.3 4.3 ± 0.3 2.8 ± 0.3 1.3 ± 0.4 3.9 ± 0.6 7.2 ± 0.3 6.0 ± 0.3 3.5 ± 0.3 1.3 ± 0.4 3.8 ± 0.6 D dimension only for reference Standard ratings F72 Cap.(µF) V Code 4 0G 6.3 0J 10 1A R 16 1C R R R F75 Cap. (µF) V Code 4 0G 6.3 0J 10 1A 033 047 068 100 150 220 330 336 476 686 107 157 227 337 R R R R R R R R R R R R R (R) 068 100 150 220 330 470 680 1000 1500 2200 686 107 157 227 337 477 687 108 158 228 C C C•D D D•R R R C•D D D•R R C C•D D R 16 1C C C D R CAT.8100V 1mm