UWF0J470MCL

ALUMINUM ELECTROLYTIC CAPACITORS WF Item Chip Type, Low Impedance series Chip type, low impedance temperature range up to +105°C. Designed for surface mounting on high density PC board. Applicable to automatic mounting machine using carrier tape. Adapted to the RoHS directive (2002/95/EC). WG Low Impedance Specifications Category Temperature Range Rated Voltage Range Rated Capacitance Range Capacitance Tolerance Leakage Current tan δ WF Low Impedance WT Performance Characteristics – 55 ~ +105°C 6.3 ~ 35V 1 ~ 220µF ± 20% at 120Hz, 20°C After 2 minutes' application of rated voltage, leakage current is not more than 0.01CV or 3 (µA) , whichever is greater. Measurement frequency : 120Hz, Rated voltage (V) tan δ ( MAX.) Temperature : 20°C 6.3 0.22 10 0.19 6.3 2 4 16 0.16 10 2 4 16 2 3 25 0.14 25 2 3 35 0.12 35 2 3 Within ±20% of initial value 200% or less of initial specified value Initial specified value or less Measurement frequency : 120Hz Stability at Low Temperature Rated voltage (V) Z– 25°C / Z+20°C Impedance ratio Z– 55°C / Z+20°C ZT / Z20 (MAX.) Endurance After 1000 hours' application of rated voltage at 105°C, capacitors meet the characteristic requirements listed at right. Capacitance change tan δ Leakage current Shelf Life Resistance to soldering heat Marking After storing the capacitors under no load at 105°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they will meet the specified value for endurance characteristics listed above. The capacitors shall be kept on the hot plate maintained at 250°C, Within ±10% of initial value Capacitance change for 30 seconds. After removing from the hot plate and restored tan δ Initial specified value or less at room temperature, they meet the characteristic requirements listed Leakage current Initial specified value or less at right. Black print on the case top. (φ4 ~ 6.3) Chip Type 0.5 MAX. Plastic platform Voltage φD ± 0.5 0.3 MAX. C ± 0.2 Positive Type numbering system (Example : 16V 10µF) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 105˚C Marking Capacitance Lot No. UWF 1 C 1 0 0 MC L 1 G B A ± 0.2 A ± 0.2 φD 4 ~ 6.3 8 Code GB GS B ± 0.2 X2P 10 16V E Taping code Configuration Capacitance tolerance (± 20%) Rated Capacitance (10µF) (mm) φD 5.4 +0.1 -0.2 (φ8) 105˚C Marking Capacitance Trade mark Plastic platform 0.3 MAX. Voltage φD ± 0.5 0.5 ~ 0.8 Negative Positive 0.5 MAX. 4 1.8 4.3 4.3 1.0 5 2.1 5.3 5.3 1.3 6.3 2.4 6.6 6.6 2.2 8 3.3 8.3 8.3 2.3 Rated voltage (16V) Series name Type C ± 0.2 A B A ± 0.2 A ± 0.2 C E B+ 0.2 – X2P 100 16V Lot No. 6.2 ± 0.3 E Dimensions V Cap. (µF) Code 0.5 ~ 0.8 Negative Voltage mark for 6.3V is 6V. 6.3 0J 10 1A 16 1C 25 1E 1 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 150 220 010 1R5 2R2 3R3 4R7 6R8 100 150 220 330 470 680 101 151 221 4 5 5 6.3 6.3 8 8 5.0 2.6 2.6 1.3 1.3 0.8 0.8 50 80 80 115 115 150 150 5 5 6.3 6.3 8 8 2.6 2.6 1.3 1.3 0.8 0.8 80 80 115 115 150 150 4 5 5 6.3 6.3 8 8 5.0 2.6 2.6 1.3 1.3 0.8 0.8 50 80 80 115 115 150 150 4 4 5 6.3 6.3 6.3 8 8 5.0 5.0 2.6 1.3 1.3 1.3 0.8 0.8 50 50 80 115 115 115 150 150 4 4 4 4 4 5 5 6.3 6.3 8 8 35 1V 5.0 5.0 5.0 5.0 5.0 2.6 2.6 1.3 1.3 0.8 0.8 50 50 50 50 50 80 80 115 115 150 150 Case size φ D (mm) Impedance Rated ripple Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.35 120 Hz 0.50 300 Hz 0.64 1 kHz 0.83 10 kHz~ 1.00 Max. Impedance (Ω) at 20°C 100kHz Rated Ripple (mArms) at 105°C 100kHz Taping specifications are given in page 24. Recommended land size, soldering by reflow are given in page 25, 26. Please select UJ(p.76) series if high C/V products are reqired. Please refer to page 3 for the minimum order quantity. CAT.8100V