UWH1C221MCL1GS

ALUMINUM  ELECTROLYTIC  CAPACITORS UWH Chip Type, High Reliability High Temperature (260°C) Reflow UWH Corresponding with 260°C peak reflow soldering Recomended reflow condition : 260°C peak 5 sec. 230°C over 60 sec. 2 times  (φ8 × 6.2, φ10 × 10 : 1 time) Chip type high temperature range, for +125°C use. High Temperature Applicable to automatic mounting machine fed with carrier tape. Compliant to the RoHS directive (2011/65/EU,(EU)2015/863). AEC-Q200 Qualified. Please contact us for details. Reflow UUB Specifications Item Performance Characteristics Category Temperature Range –40 to +125°C Rated Voltage Range 10 to 50V Rated Capacitance Range 10 to 330µF Capacitance Tolerance ± 20% at 120Hz, 20°C Leakage Current After 1 minute's application of rated voltage at 20°C, leakage current is not more than 0.03CV or 4(µA) , whichever is greater. Measurement frequency : 120Hz at 20°C Tangent of loss angle (tan δ) 10 0.32 Rated voltage (V) tan δ (max.) 16 0.24 25 0.21 35 0.18 50 0.18 Measurement frequency : 120Hz Rated voltage (V) Stability at Low Temperature Impedance ratio ZT / Z20 (max.) Z(– 40°C) / Z(+20°C) 10 16 25 35 50 12 8 6 4 4 Capacitance change tan δ Leakage current Within ±30% of the initial capacitance value 300% or less than the intial specified value Less than or equal to the initial specified value Endurance The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 1000 hours at 125°C. Shelf Life After storing the capacitors under no load at 125°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. The capacitors are kept on a hot plate for 30 seconds, which is maintained at 250°C. The capacitors shall meet the characteristic requirements listed at right when they are removed from the plate and restored to 20°C. Resistance to soldering heat Within ±10% of the initial capacitance value Less than or equal to the initial specified value Less than or equal to the initial specified value Capacitance change tan δ Leakage current Black print on the case top. Marking ※ I : Leakage Current (μA), C : Rated Capacitance (μF), V : Rated Voltage (V) Chip Type Type numbering system (Example : 10V 100µF) 1 Plastic platform B±0.2 φD±0.5 A2 100A WH Trade mark C±0.2 0.3max. Series H L±0.3 Lot No. 3 4 5 6 7 8 9 10 11 12 13 14 Taping code Configuration A±0.2 E A±0.2 Voltage (A:10V) 2 UWH 1 A 1 0 1 M C L 1 G S 0.5max. (φ8 × 6.2) Positive Capacitance tolerance (±20%) Rated capacitance (100µF) Rated voltage (10V) Negative Capacitance Series name Type L±0.5 Lot No. Capacitance V Code A B C E L H H 8 × 6.2 3.3 8.3 8.3 2.3 6.2 0.5 to 0.8 8 × 10 2.9 8.3 8.3 3.1 10 0.8 to 1.1 10 × 10 3.2 10.3 10.3 4.5 10 0.8 to 1.1 Negative Frequency coefficient of rated ripple current Voltage φD × L A±0.2 E A±0.2 B±0.2 φD±0.5 A2 100V WH Trade mark C±0.2 0.3max. Series Voltage (V:35V) (mm) Positive Plastic platform 0.5max. (φ8 × 10,φ10) 10 16 25 35 50 A C E V H Frequency Coefficient 50 Hz 0.70 120 Hz 1.00 300 Hz 1.17 1 kHz 1.36 10 kHz or more 1.50 Dimension table in next page. CAT.8100M ALUMINUM  ELECTROLYTIC  CAPACITORS UWH Dimensions Rated Voltage （V） （code） 10 （1A） 16 （1C） 25 （1E） 35 （1V） 50 （1H） Rated Capacitance （µF） Case Size φD×L（mm） tan δ 100 8× 6.2 0.32 Leakage Current （µA） at 20℃ after 1 minute （ ） 30 Rated Ripple （mArms） （125℃/120Hz） Part Number 58 UWH1A101MCL1GS 220 8×10 0.32 66 90 UWH1A221MCL1GS 330 10× 10 0.32 99 112 UWH1A331MCL1GS 100 8× 10 0.24 48 66 UWH1C101MCL1GS 220 10× 10 0.24 105.6 102 UWH1C221MCL1GS 47 8×6.2 0.21 48 UWH1E470MCL1GS 35.25 100 8×10 0.21 75 74 UWH1E101MCL1GS 220 10× 10 0.21 165 116 UWH1E221MCL1GS 33 8×6.2 0.18 44 UWH1V330MCL1GS 47 8×10 0.18 100 10×10 0.18 34.65 49.35 105 52 UWH1V470MCL1GS 80 UWH1V101MCL1GS 10 8×6.2 0.18 15 24 UWH1H100MCL1GS 22 8× 6.2 0.18 33 38 UWH1H220MCL1GS 33 8× 10 0.18 49.5 46 UWH1H330MCL1GS 47 10 ×10 0.18 70.5 58 UWH1H470MCL1GS For taping specifications, recommended land size/soldering by reflow and minimum order quantity, please refer to the Guidelines for Aluminum Electrolytic Capacitors. CAT.8100M