FR02FR10P-R

10mm Ultra-Thin SMT DIP Rotaries Series FR02 Distinctive Characteristics Slim .150” (3.8mm) body has the lowest profile in the industry and allows close stacking of PC boards. Highly visible legends and screwdriver actuator with arrow position indication provide trouble-free code setting. Detent mechanism gives crisp, positive action for accurate switch setting. Use of heat resistant resin allows infrared convection reflow soldering. Gull-winged terminals ensure mechanical stability during soldering and simplify solder joint inspection. Cam activated movable contact and gold contacts assure contact reliability and continuity. Tape-reel packaging meets EIA-481-2 Standard. Coplanarity: all considered surfaces must lie between two parallel planes that are a maximum distance apart of .0059” (0.15mm). (Additional coplanarity details in Terms and Acronyms in the Supplement section.) Actual Size N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 02-08 10mm Ultra-Thin SMT DIP Rotaries Series FR02 General Specifications Electrical Capacity (Resistive Load) Switching Rating: Nonswitching Rating: 100mA @ 5V DC 100mA @ 50V DC Other Ratings Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Nominal Operating Torque: Contact Timing: 100 milliohms maximum for circuit; 30 milliohms maximum for contact point 1,000 megohms minimum @ 250V DC 250V AC minimum for 1 minute minimum 10,000 detent operations minimum 10,000 detent operations minimum Notes: A detent operation is one actuator position operation or stepping. A cycle is one 360° rotation. 10,000 detent operations equal 625 cycles for hexadecimal devices or 1,000 cycles for decimal devices. 0.008Nm for decimal devices; 0.01Nm for hexadecimal devices Shorting (Avoid possible false signal by turning off power before switching.) Materials & Finishes Actuator: Housing & Base: Leaf Spring: Movable Contacts: Stationary Contacts: Terminals: Glass fiber reinforced polyamide (UL94V-0) Glass fiber reinforced polyamide (UL94V-0) Stainless steel Copper alloy with gold plating Phosphor bronze with gold plating Phosphor bronze with gold plating Environmental Data Operating Temperature Range: Humidity: Vibration: Shock: –25°C through +85°C (–13°F through +185°F) 90 ~ 95% humidity for 240 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 5 minutes; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Processing Soldering: Reflow Soldering Recommended. See Profile A in Supplement section. Note: During Reflow Soldering process, set the switch to the following position: FR02FR10P, FR02FR16P: 0 position; FR02FC10P: 7 position; FR02FC16P: F position Manual Soldering: See Profile A in Supplement section. These devices are not process sealed. Hand clean locally using alcohol based solution. Cleaning: Standards & Certifications Flammability Standards: UL Recognition or CSA Certification: UL94V-0 rated actuator, housing, & base The FR Series rotaries have not been tested for UL recognition or CSA certification. These switches are designed for use in a low-voltage, low-current circuit. When used as intended, the results do not produce hazardous energy. N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 02-08 10mm Ultra-Thin SMT DIP Rotaries TYPICAL SWITCH ORDERING EXAMPLE Series FR02 P S FR MOUNTING 02 SMT 02 F R CIRCUITS Real Coded (Orange Actuator) Complement Coded (Yellow Actuator) 10 TERMINALS P Gull Wing for Upright Mount R C ACTUATORS F Screwdriver Actuated 10 16 POSITIONS Decimal Hexadecimal S R DESCRIPTION FOR TYPICAL ORDERING EXAMPLE PACKAGING Stick-Tube 50 Pieces/Stick Tape-Reel 500 Pieces/Reel FR02FR10P-S Screwdriver Actuated Decimal Actuator Positions Packaged in Stick-Tube Real Coded Gull Wing Terminals for Upright Mount ACTUATORS F Screwdriver Actuated Adjusted with a flat tipped screwdriver Actuators are fully rotational either clockwise or counterclockwise. Actuator Colors: Orange for real coded devices; Yellow for complement coded devices. TRUTH TABLES (CIRCUITS & POSITIONS) Actuator Position x = ON Terminal No. (Output) 10 Decimal 16 Hexadecimal 01234567890123456789ABCDEF 1 R Real Coded Model Number: FR02FR 2 4 8 1 2 4 8 Terminal numbers are actually on the switch. 02-08 C Complement Coded Model Number: FR02FC N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 10mm Ultra-Thin SMT DIP Rotaries TYPICAL SWITCH DIMENSIONS P Upright • Screwdriver Actuated Series FR02 C L (0.2) .008 (10.0) .394 (3.8) Dia .150 (10.0) .394 901 (0.2) .008 (10.0) .394 (3.8) Dia .150 (10.0) .394 (3.9) .154 (0.1) Typ .004 (2.54) Typ .100 8 4 2 1 (2.54) Typ .100 BCD 78 01 EF 2 (1.27) Typ .050 1 2 4 8 (13.0) .512 (0.2) Typ .008 3 45 FR02FC10P Decimal Hexadecimal S Stick-Tube Each stick-tube contains 50 switches. Switches must be ordered in 50-piece increments. (16.4) .646 (16.0) .630 (540.0) 21.260 R Tape-Reel Switches must be ordered in 500-piece increments. This packaging meets EIA-481-2 Standard. Each tape-reel of 550 pockets contains 500 switches. Minimum Leader Length: 15.748” (400mm) Minimum Trailer Length: 6.299” (160mm) (6.5) R .256 (80.0) Dia 3.150 Overall Dia (330.0) 13.0 (24.4) .961 (30.4) Max 1.197 Direction of Feed N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 456 (10.5) Typ .413 (2.0) Typ .079 78 89 67 A 23 C (10.5) .413 C 456 (0.5) Typ .020 (1.0) Typ .039 (1.75) Typ .069 PACKAGING (1.75) .069 (2.0) Typ .079 (4.0) Typ .157 (16.0) Typ .630 (1.2) Typ .047 (10.3) Typ .406 (1.5) Dia Typ .059 (4.1) .161 (4.6) .181 (11.5) .453 (24.0) .945 3ϒMax 901 (10.0) .394 (2.1) Typ .083 23 (0.4) .016 02-08