0
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
会员中心
创作中心
发布
  • 发文章

  • 发资料

  • 发帖

  • 提问

  • 发视频

创作活动
LMP8603QMA

LMP8603QMA

  • 厂商:

    NSC

  • 封装:

  • 描述:

    LMP8603QMA - 60V Common Mode, Fixed Gain, Bidirectional Precision Current Sensing Amplifier - Nation...

  • 数据手册
  • 价格&库存
LMP8603QMA 数据手册
LMP8602/LMP8602Q/LMP8603/LMP8603Q 60V Common Mode, Fixed Gain, Bidirectional Precision Current Sensing Amplifier LMP8602/LMP8602Q/ LMP8603/LMP8603Q March 18, 2010 60V Common Mode, Fixed Gain, Bidirectional Precision Current Sensing Amplifier General Description The LMP8602 and LMP8603 are fixed gain precision amplifiers. The parts will amplify and filter small differential signals in the presence of high common mode voltages. The input common mode voltage range is –22V to +60V when operating from a single 5V supply. With a 3.3V supply, the input common mode voltage range is from –4V to +27V. The LMP8602 and LMP8603 are members of the Linear Monolithic Precision (LMP®) family and are ideal parts for unidirectional and bidirectional current sensing applications. All parameter values of the parts that are shown in the tables are 100% tested and all bold values are also 100% tested over temperature. The parts have a precise gain of 50x for the LMP8602 and 100x for the LMP8603, which are adequate in most targeted applications to drive an ADC to its full scale value. The fixed gain is achieved in two separate stages, a preamplifier with a gain of 10x and an output stage buffer amplifier with a gain of 5x for the LMP8602 and 10x for the LMP8603. The connection between the two stages of the signal path is brought out on two pins to enable the possibility to create an additional filter network around the output buffer amplifier. These pins can also be used for alternative configurations with different gain as described in the applications section. The mid-rail offset adjustment pin enables the user to use these devices for bidirectional single supply voltage current sensing. The output signal is bidirectional and mid-rail referenced when this pin is connected to the positive supply rail. With the offset pin connected to ground, the output signal is unidirectional and ground-referenced. The LMP8602 and LMP8603 are available in a 8–Pin SOIC package and in a 8–Pin MSOP package. The LMP8602Q and LMP8603Q incorporate enhanced manufacturing and support processes for the automotive market, including defect detection methodologies. Reliability qualification is compliant with the requirements and temperature grades defined in the AEC Q100 standard. Features Unless otherwise noted, typical values at TA = 25°C, VS = 5.0V, Gain = 50x (LMP8602), Gain = 100x (LMP8603) 10μV/°C max ■ TCVos 90 dB min ■ CMRR Input offset voltage 1 mV max ■ −4V to 27V ■ CMVR at VS = 3.3V −22V to 60V ■ CMVR at VS = 5.0V ■ Operating ambient temperature range −40°C to 125°C ■ Single supply bidirectional operation ■ All Min / Max limits 100% tested ■ LMP8602Q and LMP8603Q available in Automotive AECQ100 Grade 1 qualified version Applications ■ ■ ■ ■ ■ ■ ■ High side and low side driver configuration current sensing Bidirectional current measurement Current loop to voltage conversion Automotive fuel injection control Transmission control Power steering Battery management systems Typical Applications 30083401 LMP™ is a trademark of National Semiconductor Corporation. © 2010 National Semiconductor Corporation 300834 www.national.com LMP8602/LMP8602Q/LMP8603/LMP8603Q Absolute Maximum Ratings (Note 1) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. ESD Tolerance (Note 4) Human Body For input pins only For all other pins Machine Model Charge Device Model Supply Voltage (VS - GND) Continuous Input Voltage (−IN and +IN) (Note 6) Transient (400 ms) Maximum Voltage at A1, A2, OFFSET and OUT Pins Storage Temperature Range Junction Temperature (Note 3) Mounting Temperature Infrared or Convection (20 sec) Wave Soldering Lead (10 sec) −65°C to 150°C 150°C 235°C 260°C ±4000V ±2000V 200V 1000V 6.0V −22V to 60V −25V to 65V VS +0.3V and GND -0.3V (Note 2) Operating Ratings (Note 1) Supply Voltage (VS – GND) 3.0V to 5.5V Offset Voltage (Pin 7 ) 0 to VS Temperature Range (Note 3) Packaged devices −40°C to +125°C Package Thermal Resistance (Note 3) 8-Pin SOIC (θJA) 8-Pin MSOP (θJA) 190°C/W 203°C/W 3.3V Electrical Characteristics Unless otherwise specified, all limits guaranteed at TA = 25°C, VS = 3.3V, GND = 0V, −4V ≤ VCM ≤ 27V, and RL = ∞, Offset (Pin 7) is grounded, 10nF between VS and GND. Boldface limits apply at the temperature extremes. Symbol Parameter Conditions Min Typ Max (Note 7) (Note 5) (Note 7) 1 LMP8602 LMP8603 −40°C ≤ TA ≤ 125°C VIN = ±0.165V VCM = VS / 2 −40°C ≤ TA ≤ 125°C 0.1 Hz − 10 Hz, 6 Sigma Spectral Density, 1 kHz DC, 3.0V ≤ VS ≤ 3.6V, VCM = VS/2 LMP8602 Mid−scale Offset Scaling Accuracy Input Referred LMP8603 Input Referred Preamplifier (From input pins -IN (pin 1) and +IN (pin 8) to A1 (pin 3)) RCM RDM VOS Input Impedance Common Mode Input Impedance Differential Mode Input Offset Voltage −4V ≤ VCM ≤ 27V −4V ≤ VCM ≤ 27V VCM = VS / 2 −2V ≤ VCM ≤ 24V f = 1 kHz f = 10 kHz for 80 dB CMRR −4 9.95 99 VOL VOH 2 Units Overall Performance (From -IN (pin 1) and +IN (pin 8) to OUT (pin 5) with pins A1 (pin 3) and A2 (pin 4) connected) IS AV Supply Current Total Gain Gain Drift (Note 15) SR BW VOS TCVOS en PSRR Slew Rate (Note 8) Bandwidth Input Offset Voltage Input Offset Voltage Drift (Note 9) Input Referred Voltage Noise Power Supply Rejection Ratio 49.75 99.5 1.3 50.25 100.5 ±20 mA V/V ppm/°C V/μs kHz ±1 ±10 mV μV/°C μVP-P nV/√Hz dB ±1 ±0.33 ±0.45 ±1.5 ±0.248 250 500 295 590 ±0.15 86 80 96 94 85 27 10.0 100 ±5 RL = ∞ 3.2 2 3.25 10.05 101 ±50 10 350 700 ±1 % mV % mV kΩ kΩ mV dB dB V V/V kΩ ppm/°C mV V 50 100 −2.7 0.4 50 0.7 60 0.15 2 16.4 830 70 86 ±0.25 DC CMRR DC Common Mode Rejection Ratio AC Common Mode Rejection Ratio AC CMRR (Note 10) CMVR K1 RF-INT TCRF-INT A1 VOUT Input Common Mode Voltage Range Gain (Note 15) Output Impedance Filter Resistor Output Impedance Filter Resistor Drift A1 Output Voltage Swing www.national.com LMP8602/LMP8602Q/LMP8603/LMP8603Q Symbol Parameter Conditions Min Typ Max (Note 7) (Note 5) (Note 7) −2 −2.5 4.975 9.95 2 2.5 5.025 10.05 ±20 Units Output Buffer (From A2 (pin 4) to OUT ( pin 5 ) VOS K2 IB Input Offset Voltage Gain (Note 15) Input Bias Current of A2 (Note 11) VOL, A2 VOUT A2 Output Voltage Swing (Note 12, Note 13) RL = 100 kΩ VOH, RL = 100 kΩ ISC Output Short-Circuit Current (Note 14) Sourcing, VIN = VS, VOUT = GND Sinking, VIN = GND, VOUT = VS (Note 2) LMP8602 LMP8603 3.28 -25 30 0V ≤ VCM ≤ VS LMP8602 LMP8603 ±0.5 5 10 −40 10 10 3.29 -38 46 -60 65 40 80 mV V/V fA nA mV V mA 5V Electrical Characteristics Unless otherwise specified, all limits guaranteed for at TA = 25°C, VS = 5V, GND = 0V, −22V ≤ VCM ≤ 60V, and RL = ∞, Offset (Pin 7) is grounded, 10nF between VS and GND. Boldface limits apply at the temperature extremes. Symbol Parameter Conditions Min Typ Max (Note 7) (Note 5) (Note 7) 1.1 LMP8602 LMP8603 −40°C ≤ TA ≤ 125°C VIN = ±0.25V 0.6 50 −40°C ≤ TA ≤ 125°C 0.1 Hz − 10 Hz, 6 Sigma Input Referred Voltage Noise Power Supply Rejection Ratio Spectral Density, 1 kHz DC 4.5V ≤ VS ≤ 5.5V LMP8602 Mid−scale Offset Scaling Accuracy Input Referred LMP8603 Input Referred Preamplifier (From input pins -IN (pin 1) and +IN (pin 8) to A1 (pin 3)) RCM Input Impedance Common Mode 0V ≤ VCM ≤ 60V −20V ≤ VCM< 0V 0V ≤ VCM ≤ 60V −20V ≤ VCM < 0V VCM = VS / 2 −20V ≤ VCM ≤ 60V f = 1 kHz f = 10 kHz for 80 dB CMRR −22 9.95 99 3 Units Overall Performance (From -IN (pin 1) and +IN (pin 8) to OUT (pin 5) with pins A1 (pin 3) and A2 (pin 4) connected) IS AV Supply Current Total Gain (Note 15) Gain Drift SR BW VOS TCVOS eN PSRR Slew Rate (Note 8) Bandwidth Input Offset Voltage Input Offset Voltage Drift (Note 9) 49.75 99.5 1.5 50.25 100.5 ±20 mA V/V ppm/°C V/μs kHz ±1 ±10 mV μV/°C μVP-P nV/√Hz dB ±1 ±0.50 ±0.45 ±1.5 ±0.375 250 165 500 300 295 193 590 386 ±0.15 90 80 105 96 83 60 10 100 10.05 101 350 250 700 500 ±1 % mV % mV kΩ kΩ kΩ kΩ mV dB dB V V/V kΩ 50 100 −2.8 0.83 60 0.15 2 17.5 890 70 90 ±0.25 RDM VOS Input Impedance Differential Mode Input Offset Voltage DC CMRR DC Common Mode Rejection Ratio AC CMRR CMVR K1 RF-INT AC Common Mode Rejection Ratio (Note 10) Input Common Mode Voltage Range Gain (Note 15) Output Impedance Filter Resistor www.national.com LMP8602/LMP8602Q/LMP8603/LMP8603Q Symbol TCRF-INT A1 VOUT Parameter Output Impedance Filter Resistor Drift A1 Ouput Voltage Swing VOL VOH Conditions Min Typ Max (Note 7) (Note 5) (Note 7) ±5 ±50 10 2 4.95 −2 −2.5 4.975 9.95 4.985 2 2.5 5.025 10.05 ±20 Units ppm/°C mV V RL = ∞ Output Buffer (From A2 (pin 4) to OUT ( pin 5 ) VOS K2 IB Input Offset Voltage Gain (Note 15) Input Bias Current of A2 (Note 11) VOL, A2 VOUT A2 Ouput Voltage Swing (Note 12, Note 13) RL = 100 kΩ VOH, RL = 100 kΩ ISC Output Short-Circuit Current (Note 14) Sourcing, VIN = VS, VOUT = GND Sinking, VIN = GND, VOUT = VS LMP8602 LMP8603 4.98 –25 30 0V ≤ VCM ≤ VS LMP8602 LMP8603 ±0.5 5 10 −40 10 10 4.99 –42 48 –60 65 40 80 mV V/V fA nA mV V mA Note 1: “Absolute Maximum Ratings” indicate limits beyond which damage to the device may occur, including inoperability and degradation of the device reliability and/or performance. Functional operation of the device and/or non-degradation at the Absolute Maximum Ratings or other conditions beyond those indicated in the Recommended Operating Conditions is not implied. The Recommended Operating Conditions indicate conditions at which the device is functional and the device should not be beyond such conditions. All voltages are measured with respect to the ground pin, unless otherwise specified. Note 2: The electrical Characteristics tables list guaranteed specifications under the listed Recommended Operating Conditions except as otherwise modified or specified by the Electrical Characteristics Conditions and/or Notes. Typical specifications are estimations only and are not guaranteed. Note 3: The maximum power dissipation must be derated at elevated temperatures and is dictated by TJ(MAX), θJA, and the ambient temperature, TA. The maximum allowable power dissipation PDMAX = (TJ(MAX) - TA) / θJA or the number given in Absolute Maximum Ratings, whichever is lower. Note 4: Human Body Model per MIL-STD-883, Method 3015.7. Machine Model, per JESD22-A115-A. Field-Induced Charge-Device Model, per JESD22-C101C. Note 5: Typical values represent the most likely parameter norms at TA = +25°C, and at the Recommended Operation Conditions at the time of product characterization and are not guaranteed. Note 6: For the MSOP package, the bare board spacing at the solder pads of the package will be to small for reliable use at higher voltages (VCM >25V) Therefore it is strongly advised to add a conformal coating on the PCB assembled with the LMP8602 and LMP8603. Note 7: Datasheet min/max specification limits are guaranteed by test. Note 8: Slew rate is the average of the rising and falling slew rates. Note 9: Offset voltage drift determined by dividing the change in VOS at temperature extremes into the total temperature change. Note 10: AC Common Mode Signal is a 5VPP sine-wave (0V to 5V) at the given frequency. Note 11: Positive current corresponds to current flowing into the device. Note 12: For this test input is driven from A1 stage in uni-directional mode (Offset pin connected to GND). Note 13: For VOL, RL is connected to VS and for VOH, RL is connected to GND. Note 14: Short-Circuit test is a momentary test. Continuous short circuit operation at elevated ambient temperature can result in exceeding the maximum allowed junction temperature of 150°C. Note 15: Both the gain of the preamplifier A1V and the gain of the buffer amplifier A2V are measured individually. The over all gain of both amplifiers AV is also measured to assure the gain of all parts is always within the AV limits. www.national.com 4 LMP8602/LMP8602Q/LMP8603/LMP8603Q Block Diagram 30083405 K2 = 5 for LMP8602, K2 = 10 for LMP8603 Connection Diagram 8-Pin SOIC / MSOP 30083402 Top View Pin Descriptions Pin Power Supply Inputs Filter Network Offset Output 2 6 1 8 3 4 7 5 Name GND VS −IN +IN A1 A2 OFFSET OUT Description Power Ground Positive Supply Voltage Negative Input Positive Input Preamplifier output Input from the external filter network and / or A1 DC Offset for bidirectional signals Single ended output 5 www.national.com LMP8602/LMP8602Q/LMP8603/LMP8603Q Ordering Information Package Part Number LMP8602MA 8-Pin SOIC LMP8602MAX LMP8602QMA LMP8602QMAX LMP8602MM 8–Pin MSOP LMP8602MMX LMP8602QMM LMP8602QMMX Package Part Number LMP8603MA 8-Pin SOIC LMP8603MAX LMP8603QMA LMP8603QMAX LMP8603MM 8–Pin MSOP LMP8603MMX LMP8603QMM LMP8603QMMX Package Marking LMP8602MA LMP8602QMA AN3A AF7A Transport Media 95 Units/Rail 2.5K Units Tape and Reel 95 Units/Rail 2.5K Units Tape and Reel 1k Units Tape and Reel 3.5K Units Tape and Reel 1k Units Tape and Reel 3.5K Units Tape and Reel Transport Media 95 Units/Rail 2.5K Units Tape and Reel 95 Units/Rail 2.5K Units Tape and Reel 1k Units Tape and Reel 3.5K Units Tape and Reel 1k Units Tape and Reel 3.5K Units Tape and Reel MUA08A M08A NSC Drawing MUA08A M08A NSC Drawing Package Marking LMP8603MA LMP8603QMA AP3A AH7A Automotive Grade (Q) product incorporates enhanced manufacturing and support processes for the automotive market, including defect detection methodologies. Reliability qualification is compliant with the requirements and temperature grades defined in the AEC Q100 standard. Automotive Grade products are identified with the letter Q. Fully compliant PPAP documentation is available. For more information, go to http://www.national.com/automotive. www.national.com 6 LMP8602/LMP8602Q/LMP8603/LMP8603Q Typical Performance Characteristics VOS vs. VCM at VS = 3.3V Unless otherwise specified, all limits guaranteed for at TA = 25°C, VS = 5V, GND = 0V, −22V ≤ VCM ≤ 60V, and RL = ∞, Offset (Pin 7) connected to VS, 10nF between VS and GND. VOS vs. VCM at VS = 5V 30083424 30083425 Input Bias Current Over Temperature (+IN and −IN pins) at VS = 3.3V Input Bias Current Over Temperature (+IN and −IN pins) at VS = 5V 30083441 30083442 Input Bias Current Over Temperature (A2 pin) at VS = 5V Input Bias Current Over Temperature (A2 pin) at VS = 5V 30083427 30083426 7 www.national.com LMP8602/LMP8602Q/LMP8603/LMP8603Q Input Referred Voltage Noise vs. Frequency PSRR vs. Frequency 30083410 30083417 Gain vs. Frequency LMP8602 Gain vs. Frequency LMP8603 30083411 30083412 CMRR vs. Frequency at VS = 3.3V CMRR vs. Frequency at VS = 5V 30083428 30083429 www.national.com 8 LMP8602/LMP8602Q/LMP8603/LMP8603Q Step Response at VS = 3.3V RL = 10kΩ LMP8602 Step Response at VS = 5V RL = 10kΩ LMP8602 30083418 30083419 Settling Time (Falling Edge) at VS = 3.3V LMP8602 Settling Time (Falling Edge) at VS = 5V LMP8602 30083420 30083421 Settling Time (Rising Edge) at VS = 3.3V LMP8602 Settling Time (Rising Edge) at VS = 5V LMP8602 30083422 30083423 9 www.national.com LMP8602/LMP8602Q/LMP8603/LMP8603Q Step Response at VS = 3.3V RL = 10kΩ LMP8603 Step Response at VS = 5V RL = 10kΩ LMP8603 30083443 30083444 Settling Time (Falling Edge) at VS = 3.3V LMP8603 Settling Time (Falling Edge) at VS = 5V LMP8603 30083445 30083446 Settling Time (Rising Edge) at VS = 3.3V LMP8603 Settling Time (Rising Edge) at VS = 5V LMP8603 30083447 30083448 www.national.com 10 LMP8602/LMP8602Q/LMP8603/LMP8603Q Positive Swing vs. RLOAD at VS = 3.3V Positive Swing vs. RLOAD VS = 5V 30083413 30083415 Negative Swing vs. RLOAD at VS = 3.3V Negative Swing vs. RLOAD at VS = 5V 30083414 30083416 Gain Drift Distribution LMP8602 5000 parts Gain Drift Distribution LMP8603 5000 parts 30083437 30083483 11 www.national.com LMP8602/LMP8602Q/LMP8603/LMP8603Q Gain error Distribution at VS = 3.3V LMP8602 5000 parts Gain error Distribution at VS = 3.3V LMP8603 5000 parts 30083438 30083484 Gain error Distribution at VS = 5V LMP8602 5000 parts Gain error Distribution at VS = 5V LMP8603 5000 parts 30083439 30083485 CMRR Distribution at VS = 3.3V 5000 parts CMRR Distribution at VS = 5V 5000 parts 30083432 30083433 www.national.com 12 LMP8602/LMP8602Q/LMP8603/LMP8603Q VOS Distribution at VS = 3.3V 5000 parts VOS Distribution at VS = 5V 5000 parts 30083434 30083435 TCVOS Distribution 5000 parts 30083436 13 www.national.com LMP8602/LMP8602Q/LMP8603/LMP8603Q Application Information GENERAL The LMP8602 and LMP8603 are fixed gain differential voltage precision amplifiers with a gain of 50x for the LMP8602, and 100x for the LMP8603. The input common mode voltage range is -22V to +60V when operating from a single 5V supply or -4V to +27V input common mode voltage range when operating from a single 3.3V supply. The LMP8602 and LMP8603 are members of the LMP family and are ideal parts for unidirectional and bidirectional current sensing applications. Because of the proprietary chopping level-shift input stage the LMP8602 and LMP8603 achieve very low offset, very low thermal offset drift, and very high CMRR. The LMP8602 and LMP8603 will amplify and filter small differential signals in the presence of high common mode voltages. The LMP8602/LMP8602Q/LMP8603/LMP8603Q use level shift resistors at the inputs. Because of these resistors, the LMP8602/LMP8602Q/LMP8603/LMP8603Q can easily withstand very large differential input voltages that may exist in fault conditions where some other less protected high-performance current sense amplifiers might sustain permanent damage. PERFORMANCE GUARANTIES To guaranty the high performance of the LMP8602/LMP8602Q/LMP8603/LMP8603Q, all minimum and maximum values shown in the parameter tables of this data sheet are 100% tested where all bold limits are also 100% tested over temperature. THEORY OF OPERATION The schematic shown in Figure 1 gives a schematic representation of the internal operation of the LMP8602/ LMP8603. The signal on the input pins is typically a small differential voltage across a current sensing shunt resistor. The input signal may appear at a high common mode voltage. The input signals are accessed through two input resistors. The proprietary chopping level-shift current circuit pulls or pushes current through the input resistors to bring the common mode voltage behind these resistors within the supply rails. Subsequently, the signal is gained up by a factor of 10 (K1) and brought out on the A1 pin through a trimmed 100 kΩ resistor. In the application, additional gain adjustment or filtering components can be added between the A1 and A2 pins as will be explained in subsequent sections. The signal on the A2 pin is further amplified by a factor (K2) which equals a factor of 5 for the LMP8602 and a factor of 10 for the LMP8603. The output signal of the final gain stage is provided on the OUT pin. The OFFSET pin allows the output signal to be level-shifted to enable bidirectional current sensing as will be explained below. 30083405 K2 = 5 for LMP8602, K2 = 10 for LMP8603 FIGURE 1. Theory of Operation www.national.com 14 LMP8602/LMP8602Q/LMP8603/LMP8603Q ADDITIONAL SECOND ORDER LOW PASS FILTER The LMP8602/LMP8602Q/LMP8603/LMP8603Q has a third order Butterworth low-pass characteristic with a typical bandwidth of 60 kHz integrated in the preamplifier stage of the part. The bandwidth of the output buffer can be reduced by adding a capacitor on the A1 pin to create a first order low pass filter with a time constant determined by the 100 kΩ internal resistor and the external filter capacitor. It is also possible to create an additional second order SallenKey low pass filter as shown in Figure 2 by adding external components R2, C1 and C2. Together with the internal 100 kΩ resistor R1, this circuit creates a second order lowpass filter characteristic. 30083455 K1 = 10, K2 = 5 for LMP8602, K2 = 10 for LMP8603 FIGURE 2. Second Order Low Pass Filter When the corner frequency of the additional filter is much lower than 60 kHz, the transfer function of the described amplifier van be written as: For any filter gain K > 1x, the design procedure can be very simple if the two capacitors are chosen to in a certain ratio. Where K1 equals the gain of the preamplifier and K2 that of the buffer amplifier. The above equation can be written in the normalized frequency response for a 2nd order low pass filter: Inserting this in the above equation for Q results in: Which results in: The Cutt-off frequency ωo in rad/sec (divide by 2π to get the cut-off frequency in Hz) is given by: and the quality factor of the filter is given by: In this case, given the predetermined value of R1 = 100 kΩ ( the internal resistor), the quality factor is set solely by the value of the resistor R2. 15 www.national.com LMP8602/LMP8602Q/LMP8603/LMP8603Q R2 can be calculated based on the desired value of Q as the first step of the design procedure with the following equation: For C2 the value is calculated with: For the gain of 5 for the LMP8602 this results in: Or for a gain = 5: For the gain of 10 for the LMP8603 this is: and for a gain = 10: For instance, the value of Q can be set to 0.5√2 to create a Butterworth response, to 1/√3 to create a Bessel response, or a 0.5 to create a critically damped response. Once the value of R2 has been found, the second and last step of the design procedure is to calculate the required value of C to give the desired low-pass cut-off frequency using: Which for the gain = 5 will give: Note that the frequency response achieved using this procedure will only be accurate if the cut-off frequency of the second order filter is much smaller than the intrinsic 60 kHz low-pass filter. In other words, to have the frequency response of the LMP8602/LMP8602Q/LMP8603/LMP8603Q circuit chosen such that the internal poles do not affect the external second order filter. For a desired Q = 0.707 and a cut off frequency = 3 kHz, this will result for the LMP8602 in rounded values for R2 = 51 kΩ, C1 = 1.5 nF and C2 = 3.9 nF And for the LMP8603 this will result in rounded values for R2 = 22 kΩ, C1 = 3.3 nF and C2 = 0.39 nF GAIN ADJUSTMENT The gain of the LMP8602 is 50 and the gain of the LMP8603 is 100, however, this gain can be adjusted as the signal path in between the two internal amplifiers is available on the external pins. Reduce Gain Figure 3 shows the configuration that can be used to reduce the gain of the LMP8602 and the LMP8603. and for the gain = 10: 30083456 FIGURE 3. Reduce Gain www.national.com 16 LMP8602/LMP8602Q/LMP8603/LMP8603Q Rr creates a resistive divider together with the internal 100 kΩ resistor such that, for the LMP8602, the reduced gain Gr becomes: and for the LMP8603: For the LMP8603: From this equation, for a desired value of the gain, the required value of Ri can be calculated for the LMP8602 with: Given a desired value of the reduced gain Gr, using this equation the required value for Rr can be calculated for the LMP8602 with: and for the LMP8603 with: and for the LMP8603 with: It should be noted from the equation for the gain Gi that for large gains Ri approaches 100 kΩ. In this case, the denominator in the equation becomes close to zero. In practice, for large gains the denominator will be determined by tolerances in the value of the external resistor Ri and the internal 100 kΩ resistor. In this case, the gain becomes very inaccurate. If the denominator becomes equal to zero, the system will even become instable. It is recommended to limit the application of this technique to gain increases of a factor 2.5 or smaller. Increase Gain Figure 4 shows the configuration that can be used to increase the gain of the LMP8602/LMP8602Q/LMP8603/LMP8603Q. Ri creates positive feedback from the output pin to the input of the buffer amplifier. The positive feedback increases the gain. The increased gain Gi for the LMP8602 becomes: 30083457 FIGURE 4. Increase Gain 17 www.national.com LMP8602/LMP8602Q/LMP8603/LMP8603Q BIDIRECTIONAL CURRENT SENSING The signal on the A1 and OUT pins is ground-referenced when the OFFSET pin is connected to ground. This means that the output signal can only represent positive values of the current through the shunt resistor, so only currents flowing in one direction can be measured. When the offset pin is tied to the positive supply rail, the signal on the A1 and OUT pins is referenced to a mid-rail voltage which allows bidirectional current sensing. When the offset pin is connected to a voltage source, the output signal will be level shifted to that voltage divided by two. In principle, the output signal can be shifted to any voltage between 0 and VS/2 by applying twice that voltage from a low impedance source (Note 16) to the OFFSET pin. With the offset pin connected to the supply pin (VS) the operation of the amplifier will be fully bidirectional and symmetrical around 0V differential at the input pins. The signal at the output will follow this voltage difference multiplied by the gain and at an offset voltage at the output of half VS. Example: With 5V supply and a gain of 50x for the LMP8602, a differential input signal of +10 mV will result in 3.0V at the output pin. similarly -10 mV at the input will result in 2.0V at the output pin. With 5V supply and a gain of 100x for the LMP8603, a differential input signal of +10 mV will result in 3.5V at the output pin. similarly -10 mV at the input will result in 1.5V at the output pin. Note 16: The OFFSET pin has to be driven from a very low-impedance source ( 25V) In this situation it is strongly advised to add a conformal coating on the PCB assembled with the LMP8602/LMP8602Q/LMP8603/LMP8603Q in MSOP package. DRIVING SWITCHED CAPACITIVE LOADS Some ADCs load their signal source with a sample and hold capacitor. The capacitor may be discharged prior to being 30083430 FIGURE 6. Capacitive Load Response at 3.3V 30083431 FIGURE 7. Capacitive Load Response at 5.0V www.national.com 18 LMP8602/LMP8602Q/LMP8603/LMP8603Q These figures can be used to estimate the disturbance that will be caused when driving a switched capacitive load. To minimize the error signal introduced by the sampling that occurs on the ADC input, an additional RC filter can be placed in between the LMP8602/LMP8602Q/LMP8603/LMP8603Q and the ADC as illustrated in Figure 8. 30083461 FIGURE 8. Reduce Error When Driving ADCs The external capacitor absorbs the charge that flows when the ADC sampling capacitor is connected. The external capacitor should be much larger than the sample and hold capacitor at the input of the ADC and the RC time constant of the external filter should be such that the speed of the system is not affected. LOW SIDE CURRENT SENSING APPLICATION WITH LARGE COMMON MODE TRANSIENTS Figure 9 illustrates a low side current sensing application with a low side driver. The power transistor is pulse width modu- lated to control the average current flowing through the inductive load which is connected to a relatively high battery voltage. The current through the load is measured across a shunt resistor RSENSE in series with the load. When the power transistor is on, current flows from the battery through the inductive load, the shunt resistor and the power transistor to ground. In this case, the common mode voltage on the shunt is close to ground. When the power transistor is off, current flows through the inductive load, through the shunt resistor and through the freewheeling diode. In this case the common mode voltage on the shunt is at least one diode voltage drop above the battery voltage. Therefore, in this application the common mode voltage on the shunt is varying between a large positive voltage and a relatively low voltage. Because the large common mode voltage range of the LMP8602/ LMP8603 and because of the high AC common mode rejection ratio, the LMP8602/LMP8603 is very well suited for this application. For this application the following example can be used for the calculation of the output signal: When using a sense resistor, RSENSE, of 0.01 Ω and a current of 1A, then the output voltage at the input pins of the LMP8602 is: RSENSE * ILOAD = 0.01 Ω * 1A = 0.01V With the gain of 50 for the LMP8602 this will give an output of 0.5V. Or in other words, VOUT = 0.5V/A. For the LMP8603 the calculation is similar, but with a gain of 100, giving an output of 1 V/A. 30083452 FIGURE 9. Low Side Current Sensing Application with Large Common Mode Transients 19 www.national.com LMP8602/LMP8602Q/LMP8603/LMP8603Q LOW SIDE CURRENT SENSING APPLICATION WITH NEGATIVE COMMON MODE TRANSIENTS Figure 10 illustrates the application of the LMP8602/ LMP8603 in a high side sensing application. This application is similar to the low side sensing discussed above, except in this application the common mode voltage on the shunt drops below ground when the driver is switched off. Because the common mode voltage range of the LMP8602/LMP8603 extends below the negative rail, the LMP8602/LMP8603 is also very well suited for this application. 30083453 FIGURE 10. High Side Current Sensing Application with Negative Common Mode Transients www.national.com 20 LMP8602/LMP8602Q/LMP8603/LMP8603Q BATTERY CURRENT MONITOR APPLICATION This application example shows how the LMP8602/ LMP8603 can be used to monitor the current flowing in and out a battery pack. The fact that the LMP8602/LMP8603 can measure small voltages at a high offset voltage outside the parts own supply range makes this part a very good choice for such applications. If the load current of the battery is higher then the charging current, the output voltage of the LMP8602/LMP8603 will be above the “half offset voltage” for a net current flowing out of the battery. When the charging current is higher then the load current the output will be below this “half offset voltage”. 30083454 FIGURE 11. Battery Current Monitor Application 21 www.national.com LMP8602/LMP8602Q/LMP8603/LMP8603Q ADVANCED BATTERY CHARGER APPLICATION The above circuit can be used to realize an advanced battery charger that has the capability to monitor the exact net current that flows in and out the battery as show in Figure 12. The output signal of the LMP8602/LMP8602Q/LMP8603/LM- P8603Q is digitized with the A/D converter and used as an input for the charge controller. The charge controller can be used to regulate the charger circuit to deliver exactly the current that is required by the load, avoiding overcharging a fully loaded battery. 30083403 K2 = 5 for LMP8602 K2 = 10 for LMP8603 FIGURE 12. Advanced Battery Charger Application www.national.com 22 LMP8602/LMP8602Q/LMP8603/LMP8603Q Physical Dimensions inches (millimeters) unless otherwise noted 8Pin SOIC NS Package Number M08A 8Pin MSOP NS Package Number MUA08A 23 www.national.com LMP8602/LMP8602Q/LMP8603/LMP8603Q 60V Common Mode, Fixed Gain, Bidirectional Precision Current Sensing Amplifier Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: www.national.com Products Amplifiers Audio Clock and Timing Data Converters Interface LVDS Power Management Switching Regulators LDOs LED Lighting Voltage References PowerWise® Solutions Temperature Sensors PLL/VCO www.national.com/amplifiers www.national.com/audio www.national.com/timing www.national.com/adc www.national.com/interface www.national.com/lvds www.national.com/power www.national.com/switchers www.national.com/ldo www.national.com/led www.national.com/vref www.national.com/powerwise WEBENCH® Tools App Notes Reference Designs Samples Eval Boards Packaging Green Compliance Distributors Quality and Reliability Feedback/Support Design Made Easy Design Support www.national.com/webench www.national.com/appnotes www.national.com/refdesigns www.national.com/samples www.national.com/evalboards www.national.com/packaging www.national.com/quality/green www.national.com/contacts www.national.com/quality www.national.com/feedback www.national.com/easy www.national.com/solutions www.national.com/milaero www.national.com/solarmagic www.national.com/training Applications & Markets Mil/Aero PowerWise® Design University Serial Digital Interface (SDI) www.national.com/sdi www.national.com/wireless www.national.com/tempsensors SolarMagic™ THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION (“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright© 2010 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: support@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Technical Support Center Email: europe.support@nsc.com National Semiconductor Asia Pacific Technical Support Center Email: ap.support@nsc.com National Semiconductor Japan Technical Support Center Email: jpn.feedback@nsc.com
LMP8603QMA 价格&库存

很抱歉,暂时无法提供与“LMP8603QMA”相匹配的价格&库存,您可以联系我们找货

免费人工找货