MN101E01K

MN101E01J, MN101E01K, MN101E01L, MN101E01M Type Internal ROM type ROM (byte) RAM (byte) Package (Lead-free) 192K 10K QFP100-P-1818B 256K MN101E01J MN101E01K MN101E01L 320K 14K 20K MN101E01M 384K 24K MN101EF01M FLASH Mask ROM Minimum Instruction Execution Time LQFP100-P-1414, QFP100-P-1818B [Standard] [Standard] 0.0625 µs (at 3.0 V to 3.6 V, 32 MHz) 0.0625 µs 0.1 µs (at 3.0 V to 3.6 V, 20 MHz) (at 3.0 V to 3.6 V, 32 MHz) 62.5 µs (at 3.0 V to 3.6 V, 32 kHz) [Double speed] 0.10 µs [Double speed] 0.10 µs (at 3.0 V to 3.6 V, 10 MHz) (at 3.0 V to 3.6 V, 10 MHz)  Interrupts RESET, Watchdog, External 0 to 5, Timer 0 to 6, Timer 7 (2 systems), Time base, Serial 0 (2 systems), Serial 1 (2 systems), Serial 2, Serial 3, Serial 4 (2 systems), Automatic transfer finish, A/D conversion finish, Key interrupts (8 lines) Timer counter 0 : 8-bit × 1 (square-wave/8-bit PWM output, event count, generation of remote control carrier, pulse width measurement, generation of real time) Clock source................ 1/2, 1/4 of system clock frequency; 1/1, 1/4, 1/16, 1/32, 1/64 of OSC oscillation clock frequency; 1/1 of XI oscillation clock frequency; external clock input Interrupt source ........... coincidence with compare register 0 Timer counter 1 : 8-bit × 1 (square-wave output, event count, synchronous output event) Clock source................ 1/2, 1/8 of system clock frequency; 1/1, 1/4, 1/16, 1/64, 1/128 of OSC oscillation clock frequency; 1/1 of XI oscillation clock frequency; external clock input Interrupt source ........... coincidence with compare register 1 Timer counter 0, 1 can be cascade-connected.  Timer Counter Timer counter 2 : 8-bit × 1 (square-wave/8-bit PWM output, event count, synchronous output event, pulse width measurement generation of real time, serial baud rate timer) Clock source................ 1/2, 1/4 of system clock frequency; 1/1, 1/4, 1/16, 1/32, 1/64 of OSC oscillation clock frequency; 1/1 of XI oscillation clock frequency; external clock input Interrupt source ........... coincidence with compare register 2 Timer counter 3 : 8-bit × 1 (square-wave output, event count, generation of remote control carrier, serial baud rate timer) Clock source................ 1/2, 1/8 of system clock frequency; 1/1, 1/4, 1/16, 1/64, 1/128 of OSC oscillation clock frequency; 1/1 of XI oscillation clock frequency; external clock input Interrupt source ........... coincidence with compare register 3 Timer counter 2, 3 can be cascade-connected. Timer counter 4 : 8-bit × 1 (square-wave/8-bit PWM output, event count, pulse width measurement, serial baud rate timer) Clock source................ 1/2, 1/4 of system clock frequency; 1/1, 1/4, 1/16, 1/32, 1/64 of OSC oscillation clock frequency; 1/1 of XI oscillation clock frequency; external clock input frequency Interrupt source ........... coincidence with compare register 4 Timer counter 5 : 8-bit × 1 (square-wave output, event count, serial baud rate timer) Clock source................ 1/2, 1/4 of system clock frequency; 1/1, 1/4, 1/16, 1/64, 1/128 of OSC oscillation clock frequency; 1/1 of XI oscillation clock frequency; external clock input Interrupt source ........... coincidence with compare register 5 Timer counter 4, 5 can be cascade-connected. MAD00034KEM MN101E01J, MN101E01K, MN101E01L, MN101E01M Timer counter 6 : 8-bit freerun timer Clock source................ 1/1 of system clock frequency; 1/1, 1/4096, 1/8192 of OSC oscillation clock frequency; 1/1, 1/4096, 1/8192 of XI oscillation clock frequency Interrupt source ........... coincidence with compare register 6 Timer counter 7 : 16-bit × 1 (square-wave/16-bit PWM output, cycle / duty continuous variable, event count, synchronous output evevt, pulse width measurement, input capture) Clock source................ 1/1, 1/2, 1/4, 1/16 of system clock frequency; 1/1, 1/2, 1/4, 1/16 of OSC oscillation clock frequency; 1/1, 1/2, 1/4, 1/16 of external clock input frequency Interrupt source ........... coincidence with compare register 7 (2 lines) Time base timer (one-minute count setting) Clock source................ 1/1 of OSC oscillation clock frequency; 1/1 of XI oscillation clock frequency Interrupt source ........... 1/128, 1/256, 1/512, 1/1024, 1/8192, 1/32768 of clock source frequency Watchdog timer Interrupt source ........... 1/65536, 1/262144, 1/1048576, 1/4194304 of system clock frequency  Serial interface Serial 0 : synchronous type/UART (full-duplex) × 1 Clock source................ 1/2, 1/4 of system clock frequency; pulse output of timer counter 2, 4; 1/2, 1/4, 1/16, 1/64 of OSC oscillation clock frequency Serial 1 : synchronous type/UART (full-duplex) × 1 Clock source................ 1/2, 1/4 of system clock frequency; pulse output of timer counter 4, 5; 1/2, 1/4, 1/8, 1/16, 1/64 of OSC oscillation clock frequency Serial 2 : synchronous type/single-master I²C× 1 Clock source................ 1/2, 1/4 of system clock frequency; pulse output of timer counter 2, 3; 1/2, 1/4, 1/8, 1/16, 1/32, 1/64, 1/128 of OSC oscillation clock frequency Serial 3 : synchronous type/single-master I²C × 1 Clock source................ 1/2, 1/4 of system clock frequency; pulse output of timer counter 3, 5; 1/2, 1/4, 1/8, 1/16, 1/32, 1/64, 1/128 of OSC oscillation clock frequency Serial 4 : synchronous type/UART (full-duplex) × 1 Clock source................ 1/2, 1/4 of system clock frequency; pulse output of timer counter 2, 5 ; 1/2, 1/4, 1/16, 1/64 of OSC oscillation clock frequency  DMA controller Max. Transfer cycles : 255 Starting factor : external request, various types of interrupt, software Transfer mode : 1-byte transfer, word transfer, burst transfer  I/O Pins I/O 34 50 (5 V IF port) Common use , Specified pull-up resistor available, Input/output selectable (bit unit) (3 V IF port) Common use , Specified pull-up resistor available, Input/output selectable (bit unit)  A/D converter  D/A converter 8-bit × 1-ch. 10-bit × 8-ch. (with S/H)  Special Ports Buzzer output, remote control carrier signal output, high-current drive port Correcting address designation : up to 3 addresses possible  ROM Correction MAD00034KEM  Electrical Charactreistics (Supply current) Parameter Symbol IDD1 Operating supply current Supply current at HALT Supply current at STOP IDD2 IDD3 IDD4 IDD5 IDD6 Condition fosc = 32.0 MHz , VDD1 = 3.3 V , (fs = fosc/2) fosc = 20.0 MHz , VDD1 = 3.3 V , (fs = fosc/2) fosc = 32.768 kHz , VDD1 = 3.3 V , (fs = fosc/2) fx = 32.768 kHz , VDD1 = 3.3 V VDD1 = 3.3 V , Ta = 25°C VDD1 = 3.3 V , Ta = 85°C ( Limit min typ max Unit 11 (48) 30 (80) mA 8 (43) 22 (75) mA 30 (60) 120 (180) µA 12 0.3 30 3.0 80 µA µA µA ) : Flash memory built-in type  Development tools In-circuit Emulator PX-ICE101E+PRBV101E01-QFP100-P-1818B PX-ICE101E+PRBV101E01-LQFP100-P-1414  Pin Assignment P43 P42, SBT4 P41, SBI4, RXD4 P40, SBO4, TXD4 P87, LED7, D7 P86, LED6, D6 P85, LED5, D5 P84, LED4, D4 P83, LED3, D3 P82, LED2, D2 P81, LED1, D1 P80, LED0, D0 VSS2 P77, SDO7, NDK P76, SDO6, NWE P75, SDO5, NRE P74, SDO4, NCS P73, SDO3, A19 P72, SDO2, A18 P71, SDO1, A17 P70, SDO0, A16 P67, KEY7, A15 P66, KEY6, A14 P65, KEY5, A13 P64, KEY4, A12 TXD0B, SBO0B, P90 RXD0B, SBI0B, P91 SBT0B, P92 SDA3B, SBO3B, P93 SBI3B, P94 SCL3B, SBT3B, P95 IRQ2B, PD0 IRQ3B, PD1 TM4IOB, PD2 TM5IOB, PD3 TM7IOB, PD4 BUZZER, PD5 SYSCLK, PD6 VDD3 PD7 VSS3 AN0, PA0 AN1, PA1 AN2, PA2 AN3, PA3 AN4, PA4 AN5, PA5 AN6, PA6 AN7, PA7 5V I/F port VREF+ 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 MN101E01J MN101E01K MN101E01L MN101E01M 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 P63, KEY3, A11 P62, KEY2, A10 P61, KEY1, A9 P60, KEY0, A8 P57, A7 P56, A6 P55, A5 P54, A4 P53, A3 P52, A2 P51, A1 P50, A0 P35, SBT3A, SCL3A P34, SBI3A P33, SBO3A, SDA3A P32, SBT1 P31, SBI1, RXD1 P30, SBO1, TXD1 P25, IRQ5 P24, IRQ4 P23, IRQ3A P22, IRQ2A P21, IRQ1 P20, IRQ0 P16, TM7IOA DAVDD DA0, P06 DAVSS TXD0A, SBO0A, P00 RXD0A, SBI0A, P01 SBT0A, P02 SDA2, SBO2, P03 SBI2, P04 SCL2, SBT2, P05 VDD1 MM0D OSC2 OSC1 VSS1 XI XO VDD2 MOD1 NRST, P27 RMOUT, TM0IO, P10 TM1IO, P11 TM2IO, P12 TM3IO, P13 TM4IOA, P14 TM5IOA, P15 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 QFP100-P-1818B LQFP100-P-1414 MAD00034KEM Request for your special attention and precautions in using the technical information and semiconductors described in this book (1) If any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and regulations of the exporting country, especially, those with regard to security export control, must be observed. (2) The technical information described in this book is intended only to show the main characteristics and application circuit examples of the products, and no license is granted under any intellectual property right or other right owned by our company or any other company. Therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any other company which may arise as a result of the use of technical information described in this book. (3) The products described in this book are intended to be used for standard applications or general electronic equipment (such as office equipment, communications equipment, measuring instruments and household appliances). Consult our sales staff in advance for information on the following applications: – Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the products may directly jeopardize life or harm the human body. – Any applications other than the standard applications intended. (4) The products and product specifications described in this book are subject to change without notice for modification and/or improvement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product Standards in advance to make sure that the latest specifications satisfy your requirements. (5) When designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions (operating power supply voltage and operating environment etc.). Especially, please be careful not to exceed the range of absolute maximum rating on the transient state, such as power-on, power-off and mode-switching. Otherwise, we will not be liable for any defect which may arise later in your equipment. Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products. (6) Comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (ESD, EOS, thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. When using products for which damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages. (7) This book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of Matsushita Electric Industrial Co., Ltd. Industrial Co., Ltd.