4237-00

Product Specification PE4237 Product Description The PE4237 RF Switch is designed to cover a broad range of applications from near DC to 4000 MHz. This reflective switch integrates on-board CMOS control logic driven by a single-pin, low voltage CMOS or TTL control input. Using a nominal +3volt power supply, a 1 dB compression point of +32 dBm can be achieved. The PE4237 also exhibits outstanding isolation of better than 43 dB at 1000 MHz and is offered in a small 3x3 mm DFN package. The PE4237 is manufactured on Peregrine’s UltraCMOS™ process, a patented variation of silicon-on-insulator (SOI) technology on a sapphire substrate, offering the performance of GaAs with the economy and integration of conventional CMOS. Figure 1. Functional Diagram RFC SPDT UltraCMOS™ RF Switch DC - 4000 MHz Features • Single 3.0-volt power supply • Low insertion loss: 0.35 dB at 1000 MHz, 0.45 dB at 2000 MHz • High isolation of 43 dB at 1000 MHz, 35 dB at 2000 MHz • Typical 1 dB compression point of +32 dBm • Single-pin CMOS or TTL logic control • Available in a 6-lead DFN package Figure 2. Package Type 6-lead DFN RF1 RF2 CMOS Control Driver CTRL Table 1. Electrical Specifications @ +25 °C, VDD = 3 V (ZS = ZL = 50 Ω) Parameter Operation Frequency1 Insertion Loss Isolation – RFC to RF1/RF2 Isolation – RF1 to RF2 Return Loss ‘ON’ Switching Time ‘OFF’ Switching Time Video Feedthrough2 Input 1 dB Compression Input IP3 2000 MHz 2000 MHz, 17 dBm 30 50 1000 MHz 2000 MHz 1000 MHz 2000 MHz 1000 MHz 2000 MHz 1000 MHz 2000 MHz 50% CTRL to 0.1 dB final value, 2 GHz 50% CTRL to 25 dB isolation, 2 GHz 41 33 33.5 26.5 19 10.5 Conditions Minimum DC Typical 0.35 0.45 43 35 35 28 24 14 200 90 15 32 Maximum 4000 0.50 0.60 Units MHz dB dB dB dB dB dB dB dB ns ns mVpp dBm dBm Notes: 1. Device linearity will begin to degrade below 10 MHz. 2. The DC transient at the output of any port of the switch when the control voltage is switched from Low to High or High to Low in a 50 Ω test set-up, measured with 1ns risetime pulses and 500 MHz bandwidth. Document No. 70-0071-05 │ www.psemi.com ©2003-2008 Peregrine Semiconductor Corp. All rights reserved. Page 1 of 8 PE4237 Product Specification Figure 3. Pin Configuration RF2 GND RF1 1 2 3 Exposed Solder Pad - Shorted to Pin 2 (bottom side) Table 4. Absolute Maximum Ratings Symbol Parameter/Conditions Power supply voltage Voltage on any input except for the CTRL input Voltage on CTRL input Storage temperature range Input power (50 Ω) ESD voltage (Human Body Model) -65 Min -0.3 -0.3 Max 4.0 VDD+ 0.3 5.0 150 35 250 Units V V V °C dBm V 6 5 4 RFC CTRL VDD VI VCTRL TST VDD PIN VESD Table 2. Pin Descriptions Pin No. 1 Pin Name RF2 RF2 port.1 Description 2 GND Ground Connection. Traces should be physically short and connected to the ground plane. This pin is connected to the exposed solder pad that also must be soldered to the ground plane for best performance. RF1 port. 1 Exceeding absolute maximum ratings may cause permanent damage. Operation should be restricted to the limits in the Operating Ranges table. Operation between operating range maximum and absolute maximum for extended periods may reduce reliability. Control Logic Input The control logic input pin (CTRL) is typically driven by a 3-volt CMOS logic level signal. For flexibility to support systems that have 5-volt control logic drivers, the control logic input has been designed to handle a standard 5-volt TTL control signal. This TTL control signal input must not exceed 5-volts or damage to the switch could result. Table 5. Control Logic Truth Table Control Voltage Signal Path RFC to RF1 RFC to RF2 CTRL = CMOS or TTL High 3 4 RF1 VDD Nominal 3 V supply connection. CMOS or TTL logic level: High = RFC to RF1 signal path Low = RFC to RF2 signal path Common RF port for switch.1 5 CTRL 6 RFC Notes: 1. All RF pins must be DC blocked with an external series capacitor or held at 0 VDC. Table 3. Operating Ranges Parameter VDD Power Supply Voltage IDD Power Supply Current (VDD = 3V, VCNTL = 3V) TOP Operating temperature range Control Voltage High Control Voltage Low -40 0.7xVDD 0.3xVDD Min 2.7 Typ 3.0 29 Max 3.3 35 85 Units V µA °C V V CTRL = CMOS or TTL Low Electrostatic Discharge (ESD) Precautions When handling this UltraCMOS™ device, observe the same precautions that you would use with other ESD-sensitive devices. Although this device contains circuitry to protect it from damage due to ESD, precautions should be taken to avoid exceeding the rating specified in Table 4. Latch-Up Avoidance Unlike conventional CMOS devices, UltraCMOS™ devices are immune to latch-up. ©2003-2008 Peregrine Semiconductor Corp. All rights reserved. Page 2 of 8 Document No. 70-0071-05 │ U ltraCMOS™ RFIC Solutions PE4237 Product Specification Typical Performance Data @ -40 °C to 85 °C (Unless Otherwise Noted) Figure 4. Insertion Loss - RFC to RF1 Figure 5. Input 1dB Compression Point 0 -40 C -0.25 1dB Compression Point (dBm) 40 -40 8C 30 85 8C 25 8C Insertion Loss (dB) -0.5 85 C -0.75 25 C 20 -1 10 -1.25 -1.5 0 500 1000 1500 2000 2500 3000 3500 4000 0 0 500 1000 1500 2000 2500 3000 Frequency (MHz) Frequency (MHz) Figure 6. Insertion Loss - RFC to RF2 Figure 7. Isolation - RFC to RF1 T = 25 °C 0 -40 C -0.25 0 -20 Insertion Loss (dB) -0.5 25 C Isolation (dB) 85 C -0.75 -40 -60 -1 -1.25 -80 -1.5 0 500 1000 1500 2000 2500 3000 3500 4000 -100 0 500 1000 1500 2000 2500 3000 3500 4000 Frequency (MHz) Frequency (MHz) Document No. 70-0071-05 │ www.psemi.com ©2003-2008 Peregrine Semiconductor Corp. All rights reserved. Page 3 of 8 PE4237 Product Specification Typical Performance Data @ 25 °C Figure 8. Isolation – RFC to RF2 Figure 9. Isolation – RF1 to RF2, RF2 to RF1 0 0 -20 -20 RF2 Isolation (dB) Isolation (dB) -40 -40 RF1 -60 -60 -80 -80 - 100 0 500 1000 1500 2000 2500 3000 3500 4000 - 100 0 500 1000 1500 2000 2500 3000 3500 4000 F requency (MHz) F requency (MHz) Figure 10. Return Loss – RFC to RF1, RF2 Figure 11. Return Loss – RF1, RF2 0 0 -10 Return Loss (dB) Return Loss (dB) -10 RF2 -20 RF1 -30 -20 -30 -40 0 500 1000 1500 2000 2500 3000 3500 4000 -40 0 500 1000 1500 2000 2500 3000 3500 4000 Frequency (MHz) F requency (MHz) ©2003-2008 Peregrine Semiconductor Corp. All rights reserved. Page 4 of 8 Document No. 70-0071-05 │ U ltraCMOS™ RFIC Solutions PE4237 Product Specification Evaluation Kit The SPDT Switch Evaluation Kit board was designed to ease customer evaluation of the PE4237 SPDT switch. The RF common port is connected through a 50 Ω transmission line to the top left SMA connector, J1. Port 1 and Port 2 are connected through 50 Ω transmission lines to the top two SMA connectors on the right side of the board, J2 and J3. A through transmission line connects SMA connectors J4 and J5. This transmission line can be used to estimate the loss of the PCB over the environmental conditions being evaluated. The board is constructed of a two metal layer FR4 material with a total thickness of 0.031”. The bottom layer provides ground for the RF transmission lines. The transmission lines were designed using a coplanar waveguide with ground plane model using a trace width of 0.0476”, trace gaps of 0.030”, dielectric thickness of 0.028”, metal thickness of 0.0021” and εr of 4.4. J6 provides a means for controlling DC and digital inputs to the device. Starting from the lower left pin, the second pin to the right (J6-3) is connected to the device CNTL input. The fourth pin to the right (J6-7) is connected to the device VDD input. A decoupling capacitor (100 pF) is provided on both CTRL and VDD traces. It is the responsibility of the customer to determine proper supply decoupling for their design application. Removing these components from the evaluation board has not been shown to degrade RF performance. Figure 12. Evaluation Board Layouts Peregrine Specification 101/0085 Figure 13. Evaluation Board Schematic Peregrine Specification 102/0110 Document No. 70-0071-05 │ www.psemi.com ©2003-2008 Peregrine Semiconductor Corp. All rights reserved. Page 5 of 8 PE4237 Product Specification Figure 14. Package Drawing 6-lead DFN NOTE: The exposed solder pad (on the bottom of the package) is electrically connected to pin 2 (fused.) ©2003-2008 Peregrine Semiconductor Corp. All rights reserved. Page 6 of 8 Document No. 70-0071-05 │ U ltraCMOS™ RFIC Solutions PE4237 Product Specification Figure 15. Tape and Reel Specifications 6-lead DFN Table 6. Dimensions Dimension Ao Bo Ko P W T R7 Quantity R13 Quantity DFN 3x3 mm 3.23 ± 0.1 3.17 ± 0.1 1.37 ± 0.1 4 ± 0.1 8 +0.3, -0.1 0.254 ± 0.02 3000 N.A. Note: R7 = 7 inch Lock Reel, R13 = 13 inch Lock Reel Table 7. Ordering Information Order Code 4237-51 4237-52 4237-00 Part Marking 4237 4237 PE4237-EK Description PE4237G-06DFN 3x3mm-12800F PE4237G-06DFN 3x3mm-3000C PE4237-06DFN 3x3mm-EK Package Green 6-lead 3x3 mm DFN Green 6-lead 3x3 mm DFN Evaluation Kit Shipping Method Tape or loose 3000 units / T&R 1 / Box Document No. 70-0071-05 │ www.psemi.com ©2003-2008 Peregrine Semiconductor Corp. All rights reserved. Page 7 of 8 PE4237 Product Specification Sales Offices The Americas Peregrine Semiconductor Corporation 9380 Carroll Park Drive San Diego, CA 92121 Tel: 858-731-9400 Fax: 858-731-9499 North Asia Pacific Peregrine Semiconductor K.K. Teikoku Hotel Tower 10B-6 1-1-1 Uchisaiwai-cho, Chiyoda-ku Tokyo 100-0011 Japan Tel: +81-3-3502-5211 Fax: +81-3-3502-5213 Europe Peregrine Semiconductor Europe Bâtiment Maine 13-15 rue des Quatre Vents F-92380 Garches, France Tel: +33-1-47-41-91-73 Fax : +33-1-47-41-91-73 Peregrine Semiconductor, Korea #B-2402, Kolon Tripolis, #210 Geumgok-dong, Bundang-gu, Seongnam-si Gyeonggi-do, 463-480 S. Korea Tel: +82-31-728-4300 Fax: +82-31-728-4305 South Asia Pacific Peregrine Semiconductor, China Shanghai, 200040, P.R. China Tel: +86-21-5836-8276 Fax: +86-21-5836-7652 Space and Defense Products Americas: Tel: 858-731-9453 Europe, Asia Pacific: 180 Rue Jean de Guiramand 13852 Aix-En-Provence Cedex 3, France Tel: +33(0) 4 4239 3361 Fax: +33(0) 4 4239 7227 For a list of representatives in your area, please refer to our Web site at: www.psemi.com Data Sheet Identification Advance Information The product is in a formative or design stage. The data sheet contains design target specifications for product development. Specifications and features may change in any manner without notice. The information in this data sheet is believed to be reliable. However, Peregrine assumes no liability for the use of this information. Use shall be entirely at the user’s own risk. No patent rights or licenses to any circuits described in this data sheet are implied or granted to any third party. Peregrine’s products are not designed or intended for use in devices or systems intended for surgical implant, or in other applications intended to support or sustain life, or in any application in which the failure of the Peregrine product could create a situation in which personal injury or death might occur. Peregrine assumes no liability for damages, including consequential or incidental damages, arising out of the use of its products in such applications. The Peregrine name, logo, and UTSi are registered trademarks and UltraCMOS and HaRP are trademarks of Peregrine Semiconductor Corp. Preliminary Specification The data sheet contains preliminary data. Additional data may be added at a later date. Peregrine reserves the right to change specifications at any time without notice in order to supply the best possible product. Product Specification The data sheet contains final data. In the event Peregrine decides to change the specifications, Peregrine will notify customers of the intended changes by issuing a DCN (Document Change Notice). ©2003-2008 Peregrine Semiconductor Corp. All rights reserved. Page 8 of 8 Document No. 70-0071-05 │ U ltraCMOS™ RFIC Solutions