ET721

05124 ET721 STEERING DIODE ARRAY APPLICATIONS ✔ Ethernet - 10/100/1000 Base T ✔ Set Top Box Interfac ✔ Handheld Electronics ✔ FireWire ✔ USB Interface ✔ Sensor Interface IEC COMPATIBILITY ( EN61000-4) ✔ 61000-4-2 (ESD): Air - 15kV, Contact - 8kV ✔ 61000-4-4 (EFT): 40A - 5/50ns ✔ 61000-4-5 (Surge): 12A, 8/20µs - Level 1(Line-Gnd) & Level 2(Line-Line) SO-8 FEATURES ✔ ✔ ✔ ✔ ✔ ✔ ESD Protection > 40 kilovolts Low Clamping Voltage Provides Six (6) Lines of Protection Low Leakage Current < 200nA Low Capacitance: 3pF Typical RoHS Compliant MECHANICAL CHARACTERISTICS ✔ Molded JEDEC SO-8 ✔ Weight 70 milligrams (Approximate) ✔ Available in Lead-Free Pure-Tin Plating(Annealed) ✔ Solder Reflow Temperature: Pure-Tin - Sn, 100: 260-270°C ✔ Consult Factory for Leaded Device Availability ✔ Flammability Rating UL 94V-0 ✔ 12mm Tape and Reel Per EIA Standard 481 ✔ Marking: Marking Code, Logo, Date Code & Pin One Defined By Dot on Top of Package PIN CONFIGURATION +VCC I/O 6 I/O 5 I/O 4 8 7 6 5 1 I/O 1 2 I/O 2 3 I/O 3 4 -VEE 05124.R8 2/07 1 www.protekdevices.com ET721 DEVICE CHARACTERISTICS MAXIMUM RATINGS @ 25°C Unless Otherwise Specified PARAMETER Operating Temperature Storage Temperature Continuous Power Dissipation SYMBOL TA TSTG PPC VALUE -55 to 150 -55 to 150 145 UNITS °C °C mW ELECTRICAL CHARACTERISTICS PER LINE PART NUMBER DEVICE MARKING REPETITIVE PEAK REVERSE VOLTAGE (See Note 1) VRRM VOLTS ET721 STA 50 TYPICAL FORWARD VOLTAGE 8/20µs @1A VF VOLTS 2 @ 25°C Unless Otherwise Specified MAXIMUM REVERSE LEAKAGE CURRENT (See Note 2) @VRRM IR nA 20 MAXIMUM QUIESCENT SUPPLY CURRENT (See Note 3) @20V IRQ nA 200 TYPICAL CAPACITANCE MAXIMUM PEAK PULSE FORWARD CURRENT 8/20µs IFM AMPS 12 @0V, 1MHz Cj pF 3 Note 1: VRRM is +VCC for pin 8, -VEE for pin 4. Note 2: +20V from pin 8 to 1, 2, 3, 5, 6, and 7. -20V from pin 4 to 1, 2, 3, 5, 6 and 7. Note 3: +20V from pin 8 to 4. FIGURE 1 NON-REPETITIVE PEAK PULSE CURRENT CAPABILITY 8 IPP - Peak Pulse Current - % of IPP Peak Pulse Current - Amps 120 100 80 60 40 20 0 tf FIGURE 2 PULSE WAVE FORM Peak Value IPP TEST WAVEFORM PARAMETERS tf = 8µs td = 20µs 6 e-t 4 2 td = t I /2 PP 0 0.001 0.01 0.1 1 Square Wave Pulse - ms 10 100 0 5 10 15 t - Time - µs 20 25 30 05124.R8 2/07 2 www.protekdevices.com ET721 GRAPHS 200 FIGURE 3 TYPICAL LOW CURRENT FORWARD VOLTAGE DROP TA = 25°C SINGLE PULSE See Figure 2 Forward Current - mA 160 120 80 40 0 600 800 1,000 Forward Voltage Drop - mV 1,200 5 FIGURE 4 TYPICAL HIGH CURRENT FORWARD VOLTAGE DROP TA = 25°C SINGLE PULSE See Figure 2 4 Forward Current - A 3 2 1 0 0 1 2 Forward Voltage Drop - V 3 05124.R8 2/07 3 www.protekdevices.com ET721 SO-8 PACKAGE OUTLINE & DIMENSIONS PACKAGE OUTLINE -A- SO-8 8 5 -B - P + 0.010” (0.25 MM) M B M 4 PL DIM A B C D F G J K P R NOTES 1. 2. 3. 4. 5. 6. PACKAGE DIMENSIONS MILLIMETERS MIN MAX 4.80 3.80 1.35 0.35 0.40 1.27 BSC 0.18 0.10 5.80 0.25 INCHES MIN MAX 1 4 G D C R x 45° 0° - 10° K 0.010” (0.25 MM) M T B S A S 8 PL -T- + J F 0.196 5.00 0.189 0.150 0.157 4.00 1.75 0.054 0.068 0.49 0.014 0.019 0.049 1.250 0.016 1.27 BSC 0.05 BSC 0.05 BSC 0.25 0.007 0.009 0.004 0.008 0.25 6.20 0.229 0.244 0.019 0.50 0.010 MOUNTING PAD 0.050 ± 0.005” 0.030 ± 0.005” - T - = Seating Plane and Datum Surface. Dimensions “A” and “B” are Datum. Dimensions “A” and “B” do not include mold protrusion. Maximum mold protrusion is 0.015” (0.380 mm) per side. Dimensioning and tolerances per ANSI Y14.5M, 1982. Dimensions are exclusive of mold flash and metal burrs. TAPE & REEL/BULK ORDERING NOMENCLATURE 1. Surface mount product is taped and reeled in accordance with EIA-481. 2. Suffix-T7 = 7 Inch Reel - 1,000 pieces per 12mm tape, i.e. ET721-T7. 3. Suffix-T13 = 13 Inch Reel - 2,500 pieces per 12mm tape, i.e., ET721-T13. 4. Suffix - LF = Lead-Free, Pure-Tin Plating, i.e., ET721-LF-T7. 5. No Suffix = Product Shipped in Tubes of 98 pcs per Tube. 0.160 ± 0.005” 0.245” MIN 0.045 ± 0.005” Outline & Dimensions: Rev 1 - 11/01, 06009 COPYRIGHT © ProTek Devices 2007 SPECIFICATIONS: ProTek reserves the right to change the electrical and or mechanical characteristics described herein without notice (except JEDEC). DESIGN CHANGES: ProTek reserves the right to discontinue product lines without notice, and that the final judgement concerning selection and specifications is the buyer’s and that in furnishing engineering and technical assistance, ProTek assumes no responsibility with respect to the selection or specifications of such products. ProTek Devices 2929 South Fair Lane, Tempe, AZ 85282 Tel: 602-431-8101 Fax: 602-431-2288 E-Mail: sales@protekdevices.com Web Site: www.protekdevices.com www.protekdevices.com 05124.R8 2/07 4