SM4002

VOLTAGE RANGE 50 to 1000 Volts CURRENT 1.0 Ampere FEATURES * * * * * * G lass p assivated d evic e I deal f or s urface m ounted a pplication s L ow l eakage c urren t M etallurgically b onded c onstructio n M ounting p osition: A n y W eight: 0 .015 g ram SURFACE MOUNT GLASS PASSIVATED SILICON RECTIFIER SM4001 THR U SM4007 MECHANICAL DATA DISCONTINUED- * Epoxy : Device has UL flammability classification 94V-0 D co is ed inu nt .205 ( 5.2 ) .190 ( 4.8 ) SOLDERABLE ENDS MELF "This series is replaced by the FM400X series that meets to the same fit and function parameters and share the same solder pad layout. The FM400X series is preferred for error-free vacuum pick-up and PCB assembly.＂ .024 ( 0.6 ) .016 ( 0.4 ) .106 ( 2.7 ) .095 ( 2.4 ) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings a t 2 5 OC a mbient t emperature u nless o therwise s pecfied . Single p hase, h alf w ave, 6 0 H z, r esistive o r i nductive l oad . For c apacitive l oad, d erate c urrent b y 2 0% . Dimensions i n i nches a nd ( millimeters ) MAXIMUM RAT INGS (@ TA=25 OC u nless o therwise n oted ) R ATING S Maximum R ecurrent P eak R everse Voltag e Maximum R MS Voltag e Maximum D C B locking Voltag e Maximum Average F orward R ectified C urren t at A mbient Temperatur e Peak F orward S urge C urrent 8 .3 m s s ingle h alf s ine-wav e superimposed o n r ated l oad ( JEDEC m ethod ) Typical T hermal R esistance ( Note 1 ) Typical T hermal R esistance ( Note 1 ) Typical J unction C apacitance ( Note 2 ) Operating Te mperature Ran g e Storage Temperature R an g e O SYMBO L VRRM VRM S VDC IO I FS M RqJA RqJC CJ TJ T ST G SM4001 SM4002 SM4003 SM4004 SM4005 SM4006 SM4007 UNIT S Volt s Volt s Volt s Amp s Amp s 0 0 50 35 50 100 70 100 200 140 200 400 280 400 1.0 30 50 20 15 150 -55 to + 150 600 420 600 800 560 800 1000 700 1000 C/W C/W pF 0 0 C C ELECTRICAL C HARACTERISTICS (@TA=25 C u nless o therwise n oted ) CHARACTERISTIC S Maximum I nstantaneous F orward Voltage a t 1 .0A D C Maximum Average R everse C urren t at Rated DC Blocking Voltag e @T A = 25 oC @TA = 100 C o SYMBO L VF IR SM4001 SM4002 SM4003 SM4004 SM4005 SM4006 SM4007 UNIT S Volt s uA uA 2007- 3 1.1 5.0 100 NOTES : 1. Thermal Resistance :Mounted on PCB. 2. Measured at 1 MHz and applied reverse voltage of 4.0 volts. 3. " Fully R OHS c ompliant","100% S n p lating ( Pb-free)". RATING AND CHARACTERISTICS CURVES ( SM4001 THRU SM4007 ) INSTANTANEOUS FORWARD CURRENT, (mA) AVERAGE FORWARD CURRENT, (A) 2.0 1000 100 TA = 100 OC 10 1.0 0.1 0.01 0 T A = 7 5 OC T A = 2 5 OC 1.5 1.0 0.5 Single Phase Half Wave 60H z Resistive or Inductive Loa d 0.375" (9.5mm) Lead Lengt h 0 0 25 50 75 100 125 150 175 20 40 60 80 100 120 140 AMBIENT TEMPERATURE, (OC) PERCENT OF RATED PEAK REVERSE VOLTAGE, (%) INSTANTANEOUS REVERSE CURRENT, (A) 10 CJ, JUNCTION CAPACITANCE, (pF) 20 FIG.1 TYPICAL FORWARD CURRENT DERATING CURVE 40 20 10 8 6 4 2 1 FIG.2 TYPICAL REVERSE CHARACTERISTICS T J = 2 5 OC 1.0 0.1 T J = 2 5 OC Pulse width=30 0 S 1% Duty Cycl e 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 0.1 0.4 1.0 4 10 40 80 INSTANTANEOUS FORWARD VOLTAGE, (V) REVERSE VOLTAGE, (V) FIG.3 FIG.3 TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PEAK FORWARD SURGE CURRENT, (A) FIG.4 FIG.4 TYPICAL JUNCTION CAPACITANCE 30 25 20 15 10 0 1 8.3mS Single Half Sine-Wav e JEDEC Method 2 4 6 8 10 20 40 80 100 NUMBER OF CYCLES AT 60Hz FIG.5 MAXIMUM NON-REPETITIVE FORWARD NON-REPETITIVE SURGE CURRENT Mounting Pad Layout .100 (2.54) F-SLOT WIDTH OPTIMUM PAD SIZE .100 (2.54) .100 (2.54) .200 (5.08) .300 (7.62) Dimensions in inches and (millimeters) DISCLAIMER NOTICE Rectron Inc reserves the right to make changes without notice to any product specification herein, to make corrections, modifications, enhancements or other changes. Rectron Inc or anyone on its behalf assumes no responsibility or liability for any errors or inaccuracies. Data sheet specifications and its information contained are intended to provide a product description only. "Typical" parameters which may be included on RECTRON data sheets and/ or specifications can and do vary in different applications and actual performance may vary over time. Rectron Inc does not assume any liability arising out of the application or use of any product or circuit. Rectron products are not designed, intended or authorized for use in medical, life-saving implant or other applications intended for life-sustaining or other related applications where a failure or malfunction of component or circuitry may directly or indirectly cause injury or threaten a life without expressed written approval of Rectron Inc. Customers using or selling Rectron components for use in such applications do so at their own risk and shall agree to fully indemnify Rectron Inc and its subsidiaries harmless against all claims, damages and expenditures.