ICL3217CAZ-T

Datasheet ICL3207 Low Power, +3V to +5.5V, 250kbps, RS-232 Transmitter/Receiver The ICL3207 is a 3.0V to 5.5V powered RS-232 transmitter/receiver that meets ElA/TIA-232 and V.28/V.24 specifications, even at VCC = 3.0V. The ICL3207 features five transmitters and three receivers. Targeted applications are ISDN Terminal Adapters (TAs), PDAs, Palmtops, peripherals, and notebook and laptop computers where the low operational power and even lower standby power consumption is critical. Small footprint packaging and the use of small, low value capacitors ensure board space savings. Data rates greater than 250kbps are ensured at worst case load conditions. The ICL3207 is fully compatible with 3.3V only systems, mixed 3.3V and 5.0V systems, and 5.0V only systems. The ICL3207 is a lower power, pin-for-pin replacement for the MAX207, HIN207, and HIN237. Table 1 summarizes the features of the ICL3207. AN9863 summarizes the features of each device in the ICL32xx 3V family. Related Literature Features • Pb-free (RoHS compliant) • 15kV ESD protected (Human Body Model) • 5V lower power replacement for the MAX207, HIN207, and HIN237 • Meets EIA/TIA-232 and V.28/V.24 specifications at 3V • Latch-up free • On-chip voltage converters require only four external 0.1µF capacitors • Receiver hysteresis for improved noise immunity • Ensured minimum data rate: 250kbps • Ensured minimum slew rate: 6V/µs • Wide power supply range: Single +3V to +5.5V Applications • Any system requiring RS-232 communication ports For a full list of related documents, visit our website: ○ Battery powered, hand-held, and portable equipment • ICL3207 device page ○ Laptop computers, notebooks, and Palmtops ○ Modems, printers, and other peripherals ○ ISDN Terminal Adapters (TAs) and set top boxes Table 1. Summary of Features Part Number No. of Tx. No. of Rx. No. of Monitor Rx. (ROUTB) Data Rate (kbps) Rx. Enable Function? Manual Powerdown? Automatic Powerdown Function? ICL3207 5 3 0 250 No No No FN4892 Rev.8.00 May.16.19 Page 1 of 17 ICL3207 Contents 1. Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.1 1.2 1.3 1.4 2. Typical Operating Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pinout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pin Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 3 4 4 Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2.1 2.2 2.3 2.4 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Thermal Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Recommended Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 5 5 6 3. Typical Performance Curves. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 4. Application Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 4.1 4.1.1 4.2 4.3 4.4 4.4.1 4.5 4.6 4.7 4.8 Charge Pump. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Charge Pump Abs Max Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Transmitters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Receivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Low Power Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Low Power, Pin Compatible Replacement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Capacitor Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Power Supply Decoupling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 High Data Rates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Interconnection with 3V and 5V Logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 5. Die Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 6. Revision History. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 7. Package Outline Drawings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 FN4892 Rev.8.00 May.16.19 Page 2 of 17 ICL3207 1.1 Overview Typical Operating Circuit VCC † C3 (Optional Connection) + 9 0.1µF C1 † C2 † T1IN T2IN T3IN T4IN TTL/CMOS Logic Levels T5IN R1OUT 10 C1+ + 12 C113 C2+ + 14 C2- VCC V+ V- 7 6 18 R2OUT 2 3 T3 1 19 T4 24 21 T5 20 4 5 C3 † C4 † T1OUT T2OUT T3OUT RS-232 Levels T4OUT T5OUT R1IN 5kΩ 22 23 R2IN 5kΩ 17 16 RS-232 Levels R3IN 5kΩ R3 † - For VCC = 3.3V, C1 - C4 = 0.1µF or 0.22µF + 15 T2 R2 R3OUT 11 + T1 R1 GND For VCC = 5V, C1 - C4 = 0.1µF or 1µF 1.2 + 1. 1. Overview 8 Ordering Information Part Number (Notes 2, 3) Part Marking Temperature Range (°C) Tape and Reel (Units) (Note 1) Package (RoHS Compliant) Pkg. Dwg. # ICL3207CAZ No longer available or supported, recommended replacement: ICL3207ECAZ ICL3207 CAZ 0 to +70 - 24 Ld SSOP M24.209 ICL3207CAZ-T No longer available or supported, recommended replacement: ICL3207ECAZ-T ICL3207 CAZ 0 to +70 1k 24 Ld SSOP M24.209 ICL3207CBZ No longer available or supported, recommended replacement: ICL3207ECBZ ICL3207CBZ 0 to +70 - 24 Ld SOIC M24.3 ICL3207CBZ-T No longer available or supported, recommended replacement: ICL3207ECBZ-T ICL3207CBZ 0 to +70 1k 24 Ld SOIC M24.3 ICL3207IAZ ICL3207 IAZ -40 to +85 - 24 Ld SSOP M24.209 ICL3207IAZ-T ICL3207 IAZ -40 to +85 1k 24 Ld SSOP M24.209 Notes: 1. See TB347 for details about reel specifications. 2. These Pb-free plus anneal products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 3. For Moisture Sensitivity Level (MSL), see the ICL3207 device page. For more information about MSL, see TB363. FN4892 Rev.8.00 May.16.19 Page 3 of 17 ICL3207 1.3 1. Overview Pinout 24 Ld SOIC, SSOP Top View T3OUT 1 24 T4OUT T1OUT 2 23 R2IN T2OUT 3 22 R2OUT R1IN 4 R1OUT 5 20 T5OUT T2IN 6 19 T4IN T1IN 7 18 T3IN GND 8 17 R3OUT VCC 9 16 R3IN C1+ 10 1.4 21 T5IN 15 V- V+ 11 14 C2- C1- 12 13 C2+ Pin Descriptions Pin Function VCC System power supply input (3.0V to 5.5V). V+ Internally generated positive transmitter supply (+5.5V). V- Internally generated negative transmitter supply (-5.5V). GND Ground connection. C1+ External capacitor (voltage doubler) is connected to this lead. C1- External capacitor (voltage doubler) is connected to this lead. C2+ External capacitor (voltage inverter) is connected to this lead. C2- External capacitor (voltage inverter) is connected to this lead. T1IN, T2IN, T3IN, T4IN, T5IN TTL/CMOS compatible transmitter Inputs. T1OUT, T2OUT, T3OUT, T4OUT, RS-232 level (nominally ±5.5V) transmitter outputs. T5OUT R1IN, R2IN, R3IN RS-232 compatible receiver inputs. R1OUT, R2OUT, R3OUT TTL/CMOS level receiver outputs. FN4892 Rev.8.00 May.16.19 Page 4 of 17 ICL3207 2. 2. Specifications Specifications 2.1 Absolute Maximum Ratings Minimum Maximum Unit VCC to GND Parameter -0.3 +6 V V+ to GND -0.3 +7 V V- to GND +0.3 -7 V +14 V +6 V ±25 V ±13.2 V VCC + 0.3 V V+ to VInput Voltages -0.3 TIN RIN Output Voltages TOUT -0.3 ROUT Short-Circuit Duration Continuous TOUT See “ESD Performance” on page 6 ESD Rating CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions can adversely impact product reliability and result in failures not covered by warranty. 2.2 Thermal Information Thermal Resistance (Typical) (Note 4) θJA (°C/W) 24 Ld SOIC Package 74 24 Ld SSOP Package 100 Note: 4. θJA is measured with the component mounted on a low-effective thermal conductivity test board in free air. See TB379 for details. Parameter Minimum Maximum Junction Temperature (Plastic Package) Maximum Storage Temperature Range -65 Pb-Free Reflow Profile 2.3 Maximum Unit +150 °C +150 °C see TB493 Recommended Operating Conditions Parameter Minimum Maximum Unit ICL3207Cx 0 +70 °C ICL3207Ix -40 +85 °C Temperature Range FN4892 Rev.8.00 May.16.19 Page 5 of 17 ICL3207 2.4 2. Specifications Electrical Specifications Test Conditions: VCC = 3V to 5.5V, C1 - C4 = 0.1µF; unless otherwise specified. Typicals are at TA = 25°C Parameter Temp (°C) Min Typ Max Unit 25 - 0.3 1.0 mA Full - - 0.8 V VCC = 3.3V Full 2.0 - - V VCC = 5.0V Full 2.4 - - V Test Conditions DC Characteristics Supply Current All Outputs Unloaded Transmitter Inputs and Receiver Outputs Input Logic Threshold Low TIN Input Logic Threshold High TIN Input Leakage Current TIN Full - ±0.01 ±1.0 µA Output Voltage Low IOUT = 1.6mA Full - - 0.4 V Output Voltage High IOUT = -1.0mA Full - V VCC - 0.6 VCC - 0.1 Receiver Inputs Input Voltage Range Full -25 - 25 V VCC = 3.3V 25 0.6 1.2 - V VCC = 5.0V 25 0.8 1.5 - V VCC = 3.3V 25 - 1.5 2.4 V VCC = 5.0V 25 - 1.8 2.4 V Input Hysteresis 25 - 0.3 - V Input Resistance 25 3 5 7 kΩ Input Threshold Low Input Threshold High Transmitter Outputs Output Voltage Swing All Transmitter Outputs Loaded with 3kΩ to Ground Full ±5.0 ±5.4 - V Output Resistance VCC = V+ = V- = 0V, Transmitter Output = ±2V Full 300 10M - W Full - ±35 ±60 mA VCC = 3.15V, C1 - C4 = 0.1µF, RL = 3kΩCL = 1000pF Full 250 500 - kbps VCC = 3.0V, C1 - C4 = 0.22µF, RL = 3kΩCL = 1000pF Full 250 286 - kbps VCC  4.5V, C1 - C4 = 0.1µF, RL = 3kΩCL = 1000pF Full 250 310 - kbps Receiver Input to Receiver Output, CL = 150pF tPHL 25 - 0.3 - µs tPLH 25 - 0.3 - µs Output Short-Circuit Current Timing Characteristics Maximum Data Rate (One Transmitter Switching) Receiver Propagation Delay Transmitter Skew tPHL - tPLH Full - 200 1000 ns Receiver Skew tPHL - tPLH Full - 100 500 ns Transition Region Slew Rate VCC = 3.3V, RL = 3kΩto 7kΩ Measured From +3V to -3V or -3V to +3V CL = 200pF to 2500pF 25 4 15 30 V/µs CL = 200pF to 1000pF 25 6 15 30 V/µs Human Body Model 25 - ±15 - kV IEC61000-4-2 Contact Discharge 25 - ±8 - kV IEC61000-4-2 Air Gap Discharge 25 - ±6 - kV Human Body Model 25 - ±2 - kV ESD Performance RS-232 Pins (TOUT, RIN) All Other Pins FN4892 Rev.8.00 May.16.19 Page 6 of 17 ICL3207 3. 3. Typical Performance Curves Typical Performance Curves VCC = 3.3V, TA = 25°C 25 VOUT+ 4.0 20 2.0 Slew Rate (V/µs) Transmitter Output Voltage (V) 6.0 1 Transmitter at 250kbps Other Transmitters at 30kbps 0 -2.0 15 +Slew 10 VOUT - -4.0 -Slew -Slew -6.0 0 1000 2000 3000 4000 5 5000 0 1000 2000 3000 Figure 1. Transmitter Output Voltage vs Load Capacitance 3.5 1 Transmitter Switching No Load All Outputs Static 50 3.0 Supply Current (mA) Supply Current (mA) 250kbps 40 35 120kbps 30 25 5000 Figure 2. Slew Rate vs Load Capacitance 55 45 4000 Load Capacitance (pF) Load Capacitance (pF) 20kbps 20 2.5 2.0 1.5 1.0 0.5 15 0 1000 2000 3000 4000 5000 Load Capacitance (pF) Figure 3. Supply Current vs Load Capacitance When Transmitting Data FN4892 Rev.8.00 May.16.19 0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 Supply Voltage (V) Figure 4. Supply Current vs Supply Voltage Page 7 of 17 ICL3207 4. 4. Application Information Application Information The ICL3207 operates from a single +3V to +5.5V power supply, ensures a 250kbps minimum data rate, requires only four small external 0.1µF capacitors, features low power consumption, and meets all ElA RS-232C and V.28 specifications. 4.1 Charge Pump The ICL3207 uses regulated on-chip dual charge pumps as voltage doublers. It uses voltage inverters to generate ±5.5V transmitter supplies from a VCC supply as low as 3.0V. The charge pumps allow the ICL3207 to maintain RS-232 compliant output levels over the ±10% tolerance range of 3.3V powered systems. The efficient on-chip power supplies require only four small, external 0.1µF capacitors for the voltage doubler and inverter functions at VCC = 3.3V. See “Capacitor Selection” on page 10 and Table 5 on page 10 for capacitor recommendations for other operating conditions. The charge pumps operate discontinuously (turning off as soon as the V+ and Vsupplies are pumped up to the nominal values) and provide significant power savings. 4.1.1 Charge Pump Abs Max Ratings The ICL3207 is fully characterized for 3.0V to 3.6V operation, and at critical points for 4.5V to 5.5V operation. Furthermore, load conditions were favorable using static logic states only. The specified maximum values for V+ and V- are +7V and -7V, respectively. These limits apply for VCC values set to 3.0V and 3.6V (see Table 2). For VCC values set to 4.5V and 5.5V, the maximum values for V+ and V- can approach +9V and -7V, respectively (see Table 3 on page 9). The breakdown characteristics for V+ and V- were measured with ±13V. Table 2. V+ and V- Values for VCC = 3.0V to 3.6V C1 (μF) C2, C3, C4 (μF) Load T1IN (Logic State) 0.1 0.1 Open H 3kΩ // 1000pF 0.047 0.33 Open 3kΩ // 1000pF 1 1 Open 3kΩ // 1000pF FN4892 Rev.8.00 May.16.19 V+ (V) V- (V) VCC = 3.0V VCC = 3.6V VCC = 3.0V VCC = 3.6V 5.80 6.56 -5.60 -5.88 L 5.80 6.56 -5.60 -5.88 2.4kbps 5.80 6.56 -5.60 -5.88 H 5.88 6.60 -5.56 -5.92 L 5.76 6.36 -5.56 -5.76 2.4kbps 6.00 6.64 -5.64 -5.96 H 5.68 6.00 -5.60 -5.60 L 5.68 6.00 -5.60 -5.60 2.4kbps 5.68 6.00 -5.60 -5.60 H 5.76 6.08 -5.64 -5.64 L 5.68 6.04 -5.60 -5.60 2.4kbps 5.84 6.16 -5.64 -5.72 H 5.88 6.24 -5.60 -5.60 L 5.88 6.28 -5.60 -5.64 2.4kbps 5.80 6.20 -5.60 -5.60 H 5.88 6.44 -5.64 -5.72 L 5.88 6.04 -5.64 -5.64 2.4kbps 5.92 6.40 -5.64 -5.64 Page 8 of 17 ICL3207 Table 3. 4. Application Information V+ and V- Values for VCC = 4.5V to 5.5V V+ (V) V- (V) C1 (μF) C2, C3, C4 (μF) Load T1IN (Logic State) 0.1 0.1 Open H 7.44 8.48 -6.16 -6.40 L 7.44 8.48 -6.16 -6.44 2.4kbps 7.44 8.48 -6.17 -6.44 H 7.76 8.88 -6.36 -6.72 3kΩ // 1000pF 0.047 0.33 Open 3kΩ // 1000pF 1 1 Open 3kΩ // 1000pF VCC = 4.5V VCC = 5.5V VCC = 4.5V VCC = 5.5V L 7.08 8.00 -5.76 -5.76 2.4kbps 7.76 8.84 -6.40 -6.64 H 6.44 6.88 -5.80 -5.88 L 6.48 6.88 -5.84 -5.88 2.4kbps 6.44 6.88 -5.80 -5.88 H 6.64 7.28 -5.92 -6.04 L 6.24 6.60 -5.52 -5.52 2.4kbps 6.72 7.16 -5.92 -5.96 H 6.84 7.60 -5.76 -5.76 L 6.88 7.60 -5.76 -5.76 2.4kbps 6.92 7.56 -5.72 -5.76 H 7.28 8.16 -5.80 -5.92 L 6.44 6.84 -5.64 -6.84 2.4kbps 7.08 7.76 -5.80 -5.80 The resulting new maximum voltages at V+ and V- are listed in Table 4. Table 4. 4.2 New Measured Withstanding Voltages V+, V- to Ground ±13V V+ to V- 20V Transmitters The transmitters are proprietary, low dropout, inverting drivers that translate TTL/CMOS inputs to EIA/TIA-232 output levels. The transmitters are coupled with the on-chip ±5.5V supplies to deliver true RS-232 levels across a wide range of single supply system voltages. The ICL3207 ensures a 250kbps data rate for full load conditions (3kΩ and 1000pF), VCC ≥ 3.0V, with one transmitter operating at full speed. Under more typical conditions of VCC ≥ 3.3V, RL = 3kΩ, and CL = 250pF, one transmitter easily operates at 800kbps. Transmitter inputs float if they are not connected and can cause ICC to increase. Connect unused inputs to GND for the best performance. FN4892 Rev.8.00 May.16.19 Page 9 of 17 ICL3207 4.3 4. Application Information Receivers The ICL3207 has inverting receivers that convert RS-232 signals to CMOS output levels and accept inputs up to ±25V while presenting the required 3kΩ to 7kΩ input impedance (see Figure 5) even if the power is off (VCC = 0V). The receivers’ Schmitt trigger input stage uses hysteresis to increase noise immunity and decrease errors due to slow input signal transitions. Receivers on the ICL3207 are always active. VCC RXIN -25V ≤ VRIN ≤ +25V RXOUT 5kΩ GND ≤ VROUT ≤ VCC GND Figure 5. Inverting Receiver Connections 4.4 Low Power Operation The 3V ICL3207 requires a nominal supply current of 0.3mA, even at VCC = 5.5V, during normal operation. This supply current is considerably less than the 11mA current required by comparable 5V RS-232 devices and allows you to reduce system power by replacing the old style device with the ICL3207. 4.4.1 Low Power, Pin Compatible Replacement Pin compatibility with existing 5V products (such as the MAX207), coupled with the wide operating supply range, makes the ICL3207 a potential lower power, higher performance drop-in replacement for existing 5V applications. As long as the ±5V RS-232 output swings are acceptable, the ICL3207 works in most 5V applications. When replacing a device in an existing 5V application, it is acceptable to terminate C3 to VCC as shown in the “Typical Operating Circuit” on page 3. Terminate C3 to GND if possible, as slightly better performance results from this configuration. 4.5 Capacitor Selection The charge pumps require 0.1µF or greater capacitors for 3.3V operation. With 0.1µF capacitors, 5% tolerance supplies (3.14V minimum) deliver greater than ±5V transmitter swings at full data rate. 10% tolerance supplies (2.97V minimum) deliver ±4.95V transmitter swings. If greater than ±5V transmitter swings are required with a 10% tolerance 3.3V supply, 0.22µF capacitors are recommended (see Table 5). Existing 5V applications typically use either 0.1µF or 1µF capacitors, and the ICL3207 works well with either value. New 5V designs should use 0.22µF capacitors for the best results. For other supply voltages, see Table 5 for capacitor values. Do not use values smaller than those listed in Table 5. Increasing the capacitor values (by a factor of 2) reduces ripple on the transmitter outputs and slightly reduces power consumption. C2, C3, and C4 can be increased without increasing C1’s value; however, do not increase C1 without also increasing C2, C3, and C4 to maintain the proper ratios (C1 to the other capacitors). When using minimum required capacitor values, make sure that capacitor values do not degrade excessively with temperature. If in doubt, use capacitors with a larger nominal value. The capacitor’s Equivalent Series Resistance (ESR) usually rises at low temperatures and influences the amount of ripple on V+ and V-. Table 5. Required Capacitor Values VCC (V) C1 (µF) C2, C3, C4 (µF) 3.15 to 3.6 0.1 0.1 3.0 to 3.6 0.22 0.22 4.5 to 5.5 0.1 to 1.0 0.1 to 1.0 3.0 to 5.5 0.22 0.22 FN4892 Rev.8.00 May.16.19 Page 10 of 17 ICL3207 4.6 4. Application Information Power Supply Decoupling In most circumstances, a 0.1µF bypass capacitor is adequate. In applications that are particularly sensitive to power supply noise, decouple VCC to ground with a capacitor of the same value as the charge pump capacitor C1. Connect the bypass capacitor as close as possible to the IC. 4.7 High Data Rates The ICL3207 maintains the RS-232 ±5V minimum transmitter output voltages even at high data rates. Figure 6 shows a transmitter loopback test circuit, and Figure 7 illustrates the loopback test result at 120kbps. For this test, all transmitters were simultaneously driving RS-232 loads in parallel with 1000pF, at 120kbps. Figure 8 shows the loopback results for a single transmitter driving 1000pF and an RS-232 load at 250kbps. The static transmitters were also loaded with an RS-232 receiver. VCC + 0.1µF + C1 C1+ VCC V+ C1+ C2 ICL3207 V- C2+ C2TIN ROUT + C3 C4 + TOUT RIN 1000pF 5k Figure 6. Transmitter Loopback Test Circuit 5V/Div 5V/Div T1IN T1IN T1OUT T1OUT R1OUT R1OUT VCC = +3.3V C1 - C4 = 0.1µF VCC = +3.3V C1 - C4 = 0.1µF 5µs/Div Figure 7. Loopback Test at 120kbps FN4892 Rev.8.00 May.16.19 2µs/Div Figure 8. Loopback Test at 250kbps Page 11 of 17 ICL3207 4.8 4. Application Information Interconnection with 3V and 5V Logic The ICL3207 directly interfaces with most 5V logic families, including ACT and HCT CMOS. See Table 6 for more information about possible combinations of interconnections. Table 6. Logic Family Compatibility With Various Supply Voltages System Power-Supply Voltage (V) VCC Supply Voltage (V) 3.3 3.3 5 5 5 3.3 FN4892 Rev.8.00 May.16.19 Compatibility Compatible with all CMOS families. Compatible with all TTL and CMOS logic families. Compatible with ACT and HCT CMOS, and with TTL. Incompatible with AC, HC, or CD4000 CMOS. Page 12 of 17 ICL3207 5. 5. Die Characteristics Die Characteristics Substrate Potential (Powered Up) GND Transistor Count 469 Process Si Gate CMOS FN4892 Rev.8.00 May.16.19 Page 13 of 17 ICL3207 6. 6. Revision History Revision History Revision Date 8.00 May.16.19 Removed information about the ICL3217 throughout the datasheet Updated related literature section on page 1. Updated the ordering information table on page 3: -Changed Note 1 and added Note 3 -Added tape and reel column -Removed the retired ICL3217CAZ, ICL3217CBZ, ICL3217IAZ, and ICL3217IBZ -Added information about recommended replacements for end of life parts: ICL3207CAZ, ICL3207CAZ-T, ICL3207CBZ, and ICL3207CBZ-T Added Charge Pump Abs Max Ratings section starting on page 8. Removed About Intersil section. Applied new template. Updated disclaimer. 7.00 Aug.21.15 Updated Ordering Information table on page 4. Added Revision History and About Intersil sections. Updated Package Outline Drawing M24.3 to the latest revision updates are as follows: -Revision 0 to Revision 1, Removed µ symbol which is overlapping the alpha symbol in the diagram. -Revision 1 to Revision 2, Updated to new POD standard by removing table listing dimensions and putting dimensions on drawing. Added Land Pattern. FN4892 Rev.8.00 May.16.19 Change Page 14 of 17 ICL3207 7. 7. Package Outline Drawings Package Outline Drawings For the most recent package outline drawing, see M24.209. M24.209 (JEDEC MO-150-AG ISSUE B) 24 LEAD SHRINK SMALL OUTLINE PLASTIC PACKAGE INCHES N INDEX AREA H 0.25(0.010) M GAUGE PLANE -B1 2 3 0.25 0.010 SEATING PLANE -A- B M E A D -C- e  C 0.10(0.004) C A M SYMBOL MIN MAX MIN MAX NOTES A - 0.078 - 2.00 - A1 0.002 0.05 - - A2 0.065 0.072 1.65 1.85 - B 0.009 0.014 0.22 0.38 9 C 0.004 0.009 0.09 0.25 - D 0.312 0.334 7.90 8.50 3 E 0.197 0.220 5.00 5.60 4 e A2 A1 B 0.25(0.010) M L B S NOTES: 5. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of Publication Number 95. MILLIMETERS - 0.026 BSC 0.65 BSC - H 0.292 0.322 7.40 8.20 - L 0.022 0.037 0.55 0.95 6 N  24 0o 24 8o 0o 7 8o Rev. 1 3/95 6. Dimensioning and tolerancing per ANSI Y14.5M-1982. 7. Dimension “D” does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.20mm (0.0078 inch) per side. 8. Dimension “E” does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.20mm (0.0078 inch) per side. 9. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 10. “L” is the length of terminal for soldering to a substrate. 11. “N” is the number of terminal positions. 12. Terminal numbers are shown for reference only. 13. Dimension “B” does not include dambar protrusion. Allowable dambar protrusion shall be 0.13mm (0.005 inch) total in excess of “B” dimension at maximum material condition. 14. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. FN4892 Rev.8.00 May.16.19 Page 15 of 17 ICL3207 7. Package Outline Drawings For the most recent package outline drawing, see M24.3. M24.3 24 LEAD WIDE BODY SMALL OUTLINE PLASTIC PACKAGE (SOIC) Rev 2, 3/11 24 INDEX AREA 7.60 (0.299) 7.40 (0.291) 10.65 (0.419) 10.00 (0.394) DETAIL "A" 1 2 3 TOP VIEW 1.27 (0.050) 0.40 (0.016) SEATING PLANE 2.65 (0.104) 2.35 (0.093) 15.60 (0.614) 15.20 (0.598) 0.75 (0.029) x 45° 0.25 (0.010) 0.30 (0.012) 0.10 (0.004) 1.27 (0.050) 0.51 (0.020) 0.33 (0.013) 8° 0° 0.32 (0.012) 0.23 (0.009) SIDE VIEW “B” SIDE VIEW “A” 1.981 (0.078) 9.373 (0.369) 1.27 (0.050) NOTES: 15. Dimensioning and tolerancing per ANSI Y14.5M-1982. 16. Package length does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 17. Package width does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm (0.010 inch) per side. 18. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 19. Terminal numbers are shown for reference only. 20. The lead width as measured 0.36mm (0.014 inch) or greater above the seating plane, shall not exceed a maximum value of 0.61mm (0.024 inch). 21. Controlling dimension: MILLIMETER. Converted inch dimensions in ( ) are not necessarily exact. 22. This outline conforms to JEDEC publication MS-013-AD ISSUE C. 0.533 (0.021) TYPICAL RECOMMENDED LAND PATTERN FN4892 Rev.8.00 May.16.19 Page 16 of 17 1RWLFH  'HVFULSWLRQVRIFLUFXLWVVRIWZDUHDQGRWKHUUHODWHGLQIRUPDWLRQLQWKLVGRFXPHQWDUHSURYLGHGRQO\WRLOOXVWUDWHWKHRSHUDWLRQRIVHPLFRQGXFWRUSURGXFWV DQGDSSOLFDWLRQH[DPSOHV