ISL9000IRMMZ

W DESIGNS D E D FO R N E N E M M O C E MENT PART N OT R D REPLACE E D N E M M O REC ISL9000A ISL9000 DATASHEET FN9217 Rev 4.00 March 11, 2008 Dual LDO with Low Noise, Very High PSRR and Low IQ ISL9000 is a high performance dual LDO capable of sourcing 300mA current from each output. It has a low standby current and very high PSRR and is stable with output capacitance of 1µF to 10µF with ESR of up to 200m. Features The device integrates an individual Power-On-Reset (POR) function for each output. The POR delay for VO2 can be externally programmed by connecting a timing capacitor to the CPOR pin. The POR delay for VO1 is internally fixed at approximately 2ms. A reference bypass pin is also provided for connecting a noise filtering capacitor for low noise and high-PSRR applications. • ±1.8% accuracy over all operating conditions The quiescent current is typically only 42µA with both LDOs enabled and active. Separate enable pins control each individual LDO output. When both enable pins are low, the device is in shutdown, typically drawing less than 0.1µA. Several combinations of voltage outputs are standard. Output voltage options for each LDO range are from 1.5V to 3.3V. Other output voltage options may be available upon request. • Integrates two 300mA high performance LDOs • Excellent transient response to large current steps • Excellent load regulation: < 0.1% voltage change across full range of load current • Low output noise: typically 30µVRMS @ 100µA (1.5V) • Very high PSRR: 90dB @ 1kHz • Extremely low quiescent current: 42µA (both LDOs active) • Wide input voltage capability: 2.3V to 6.5V • Low dropout voltage: typically 200mV @ 300mA • Stable with 1µF to 10µF ceramic capacitors • Separate enable and POR pins for each LDO • Soft-start and staged turn-on to limit input current surge during enable • Current limit and overheat protection Pinout • Tiny 10 Ld 3mmx3mm DFN package ISL9000 (10 LD 3X3 DFN) TOP VIEW • -40°C to +85°C operating temperature range • Pb-free (RoHS compliant) VIN 1 10 VO1 Applications EN1 2 9 VO2 • PDAs, Cell Phones and Smart Phones EN2 3 8 POR2 • Portable Instruments, MP3 Players CBYP 4 7 POR1 • Handheld Devices including Medical Handhelds CPOR 5 6 GND FN9217 Rev 4.00 March 11, 2008 Page 1 of 11 ISL9000 Ordering Information PART NUMBER (Notes 1, 2, 3) PART MARKING VO1 VOLTAGE (V) VO2 VOLTAGE (V) TEMP RANGE (°C) PACKAGE (Pb-Free) PKG DWG. # ISL9000IRNNZ DCGA 3.3 3.3 -40 to +85 10 Ld 3x3 DFN L10.3x3C ISL9000IRNJZ DAAA 3.3 2.8 -40 to +85 10 Ld 3x3 DFN L10.3x3C ISL9000IRNFZ DBAA 3.3 2.5 -40 to +85 10 Ld 3x3 DFN L10.3x3C ISL9000IRNCZ DABH 3.3 1.8 -40 to +85 10 Ld 3x3 DFN L10.3x3C ISL9000IRMNZ DCHA 3.0 3.3 -40 to +85 10 Ld 3x3 DFN L10.3x3C ISL9000IRMMZ DSAA 3.0 3.0 -40 to +85 10 Ld 3x3 DFN L10.3x3C ISL9000IRMGZ DCJA 3.0 2.7 -40 to +85 10 Ld 3x3 DFN L10.3x3C ISL9000IRLLZ DRAA 2.9 2.9 -40 to +85 10 Ld 3x3 DFN L10.3x3C ISL9000IRKNZ DABF 2.85 3.3 -40 to +85 10 Ld 3x3 DFN L10.3x3C ISL9000IRKKZ DCAA 2.85 2.85 -40 to +85 10 Ld 3x3 DFN L10.3x3C ISL9000IRKJZ DDAA 2.85 2.8 -40 to +85 10 Ld 3x3 DFN L10.3x3C ISL9000IRKFZ DEAA 2.85 2.5 -40 to +85 10 Ld 3x3 DFN L10.3x3C ISL9000IRKPZ DABG 2.85 1.85 -40 to +85 10 Ld 3x3 DFN L10.3x3C ISL9000IRKCZ DHAA 2.85 1.8 -40 to +85 10 Ld 3x3 DFN L10.3x3C ISL9000IRJNZ DCKA 2.8 3.3 -40 to +85 10 Ld 3x3 DFN L10.3x3C ISL9000IRJMZ DPAA 2.8 3.0 -40 to +85 10 Ld 3x3 DFN L10.3x3C ISL9000IRJRZ DNAA 2.8 2.6 -40 to +85 10 Ld 3x3 DFN L10.3x3C ISL9000IRJCZ DMAA 2.8 1.8 -40 to +85 10 Ld 3x3 DFN L10.3x3C ISL9000IRJBZ DFAA 2.8 1.5 -40 to +85 10 Ld 3x3 DFN L10.3x3C ISL9000IRGPZ DABE 2.7 1.85 -40 to +85 10 Ld 3x3 DFN L10.3x3C ISL9000IRGCZ DLAA 2.7 1.8 -40 to +85 10 Ld 3x3 DFN L10.3x3C ISL9000IRFJZ DGAA 2.5 2.8 -40 to +85 10 Ld 3x3 DFN L10.3x3C ISL9000IRFDZ DCLA 2.5 2.0 -40 to +85 10 Ld 3x3 DFN L10.3x3C ISL9000IRFCZ DCMA 2.5 1.8 -40 to +85 10 Ld 3x3 DFN L10.3x3C ISL9000IRPLZ DKAA 1.85 2.9 -40 to +85 10 Ld 3x3 DFN L10.3x3C ISL9000IRPPZ DABJ 1.85 1.85 -40 to +85 10 Ld 3x3 DFN L10.3x3C ISL9000IRCJZ DCNA 1.8 2.8 -40 to +85 10 Ld 3x3 DFN L10.3x3C ISL9000IRCCZ DCPA 1.8 1.8 -40 to +85 10 Ld 3x3 DFN L10.3x3C ISL9000IRBLZ DABD 1.5 2.9 -40 to +85 10 Ld 3x3 DFN L10.3x3C ISL9000IRBJZ DJAA 1.5 2.8 -40 to +85 10 Ld 3x3 DFN L10.3x3C ISL9000IRBCZ DABC 1.5 1.8 -40 to +85 10 Ld 3x3 DFN L10.3x3C ISL9000IRBBZ DABB 1.5 1.5 -40 to +85 10 Ld 3x3 DFN L10.3x3C NOTES: 1. Add “-T” suffix for tape and reel. Please refer to TB347 for details on reel specifications. 2. For other output voltages, contact Intersil Marketing. 3. These Intersil Pb-free plastic packaged products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate PLUS ANNEAL - e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. FN9217 Rev 4.00 March 11, 2008 Page 2 of 11 ISL9000 Absolute Maximum Ratings Thermal Information Supply Voltage (VIN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +7.1V VO1, VO2 Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +3.6V All Other Pins . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to (VIN + 0.3)V Thermal Resistance (Notes 4, 5) Recommended Operating Conditions Ambient Temperature Range (TA) . . . . . . . . . . . . . . .-40°C to +85°C Supply Voltage (VIN) . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.3V to 6.5V JA (°C/W) JC (°C/W) 10 Ld 3x3 DFN Package . . . . . . . . . . . 50 10 Junction Temperature Range . . . . . . . . . . . . . . . . .-40°C to +125°C Operating Temperature Range . . . . . . . . . . . . . . . . .-40°C to +85°C Storage Temperature Range . . . . . . . . . . . . . . . . . .-65°C to +150°C Pb-free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . .see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty. NOTES: 4. JA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See Tech Brief TB379. 5. For JC, the “case temp” location is the center of the exposed metal pad on the package underside. Electrical Specifications PARAMETER Unless otherwise noted, all parameters are guaranteed over the operational supply voltage and temperature range of the device as follows: TA = -40°C to +85°C; VIN = (VO + 0.5V) to 6.5V with a minimum VIN of 2.3V; CIN = 1µF; CO = 1µF; CBYP = 0.01µF; CPOR = 0.01µF. SYMBOL TEST CONDITIONS MIN (Note 8) TYP MAX (Note 8) UNITS 6.5 V DC CHARACTERISTICS Supply Voltage 2.3 VIN Ground Current Quiescent condition: IO1 = 0µA; IO2 = 0µA IDD1 One LDO active 25 32 µA IDD2 Both LDO active 42 52 µA Shutdown Current IDDS @ +25°C 0.1 1.0 µA UVLO Threshold VUV+ 1.9 2.1 2.3 V VUV- 1.6 1.8 2.0 V Regulation Voltage Accuracy Maximum Output Current IMAX Internal Current Limit ILIM Dropout Voltage (Note 7) Thermal Shutdown Temperature Initial accuracy at VIN = VO + 0.5V, IO = 10mA, TJ = +25°C -0.7 +0.7 % VIN = VO + 0.5V to 5.5V, IO = 10µA to 300mA, TJ = +25°C -0.8 +0.8 % VIN = VO + 0.5V to 5.5V, IO = 10µA to 300mA, TJ = -40°C to +125°C -1.8 +1.8 % Continuous 300 350 mA 475 600 mA VDO1 IO = 300mA; VO  2.5V 300 500 mV VDO2 IO = 300mA; 2.5V  VO  2.8V 250 400 mV VDO3 IO = 300mA; VO > 2.8V 200 325 mV TSD+ 145 °C TSD- 110 °C @ 1kHz 90 dB @ 10kHz 70 dB @ 100kHz 50 dB IO = 100µA, VO = 1.5V, TA = +25°C, CBYP = 0.1µF BW = 10Hz to 100kHz 30 µVRMS AC CHARACTERISTICS Ripple Rejection (Note 6) Output Noise Voltage (Note 6) IO = 10mA, VIN = 2.8V(min), VO = 1.8V, CBYP = 0.1µF DEVICE START-UP CHARACTERISTICS FN9217 Rev 4.00 March 11, 2008 Page 3 of 11 ISL9000 Electrical Specifications PARAMETER Unless otherwise noted, all parameters are guaranteed over the operational supply voltage and temperature range of the device as follows: TA = -40°C to +85°C; VIN = (VO + 0.5V) to 6.5V with a minimum VIN of 2.3V; CIN = 1µF; CO = 1µF; CBYP = 0.01µF; CPOR = 0.01µF. (Continued) TYP MAX (Note 8) UNITS Time from assertion of the ENx pin to when the output voltage reaches 95% of the VO(nom) 250 500 µs Slope of linear portion of LDO output voltage ramp during start-up 30 60 µs/V SYMBOL Device Enable Time tEN LDO Soft-Start Ramp Rate tSSR MIN (Note 8) TEST CONDITIONS EN1, EN2 PIN CHARACTERISTICS Input Low Voltage VIL -0.3 0.5 V Input High Voltage VIH 1.4 VIN + 0.3 V 0.1 µA Input Leakage Current IIL, IIH Pin Capacitance CPIN Informative 5 pF POR1, POR2 PIN CHARACTERISTICS POR1, POR2 Thresholds POR1 Delay VPOR+ As a percentage of nominal output voltage 91 94 97 % VPOR- 87 90 93 % tP1LH 1.0 2.0 3.0 ms tP1HL POR2 Delay tP2LH 25 CPOR = 0.01µF 100 POR1, POR2 Pin Internal Pull-Up Resistance VOL 300 25 tP2HL POR1, POR2 Pin Output Low Voltage 200 µs @IOL = 1.0mA RPOR 78 100 ms µs 0.2 V 180 k NOTES: 6. Limits established by characterization and are not production tested. 7. VOx = 0.98*VOx(NOM); Valid for VOx greater than 1.85V. 8. Parts are 100% tested at +25°C. Temperature limits established by characterization and are not production tested. EN1 EN2 tEN VPOR+ VPOR- VPOR+ VPOR-