ISL9005IRFZ-T

DATASHEET NOT RECOMMENDED FOR NEW DESIGNS RECOMMENDED REPLACEMENT PART ISL9005A ISL9005 FN9234 Rev 2.00 May 5, 2008 LDO with Low ISUPPLY, High PSRR ISL9005 is a high performance Low Dropout linear regulator capable of sourcing 300mA current. It has a low standby current and high-PSRR and is stable with output capacitance of 1µF to 10µF with ESR of up to 200m. Features The ISL9005 has a high PSRR of 75dB and output noise less than 45µVRMS. When coupled with a no load quiescent current of 50µA (typical), and 0.1µA shutdown current, the ISL9005 is an ideal choice for portable wireless equipment. • Excellent load regulation: 2.8V 200 325 mV TSD+ 145 °C TSD- 110 °C @ 1kHz 75 dB @ 10kHz 60 dB @ 100kHz 40 dB IO = 100µA, VO = 1.5V, TA = +25°C BW = 10Hz to 100kHz 45 µVRMS AC CHARACTERISTICS Ripple Rejection (Note 6) Output Noise Voltage (Note 6) FN9234 Rev 2.00 May 5, 2008 IO = 10mA, VIN = 2.8V (min), VO = 1.8V Page 2 of 9 ISL9005 Electrical Specifications PARAMETER Unless otherwise noted, all parameters are guaranteed over the operational supply voltage and temperature range of the device as follows: TA = -40°C to +85°C; VIN = (VO + 0.5V) to 5.5V with a minimum VIN of 2.3V; CIN = 1µF; CO = 1µF. (Continued) MIN MAX (Note 8) TYP (Note 8) UNITS Time from assertion of the ENx pin to when the output voltage reaches 95% of the VO (nom) 250 500 µs Slope of linear portion of LDO output voltage ramp during start-up 30 60 µs/V SYMBOL TEST CONDITIONS DEVICE START-UP CHARACTERISTICS Device Enable Time LDO Soft-start Ramp Rate tEN tSSR EN PIN CHARACTERISTICS Input Low Voltage VIL -0.3 0.5 V Input High Voltage VIH 1.4 VIN + 0.3 V 0.1 µA Input Leakage Current IIL, IIH Pin Capacitance CPIN Informative 5 pF NOTES: 6. Limits established by characterization and are not production tested. 7. VOx = 0.98*VOx(NOM); Valid for VOx greater than 1.85V. 8. Parts are 100% tested at +25°C. Temperature limits established by characterization and are not production tested. FN9234 Rev 2.00 May 5, 2008 Page 3 of 9 ISL9005 Typical Performance Curves 0.10 0.8 VO = 3.3V ILOAD = 0mA 0.4 0.2 -40°C 0.0 +25°C -0.2 +85°C -0.4 VIN = 3.8V VO = 3.3V 0.08 OUTPUT VOLTAGE CHANGE (%) OUTPUT VOLTAGE, VO (%) 0.6 -0.6 0.06 0.04 -40°C 0.02 +25°C 0.00 -0.02 +85°C -0.04 -0.06 -0.08 -0.8 3.4 3.8 4.6 4.2 5.0 5.4 5.8 6.2 -0.10 6.6 0 100 50 FIGURE 1. OUTPUT VOLTAGE vs INPUT VOLTAGE (3.3V OUTPUT) 250 300 400 350 FIGURE 2. OUTPUT VOLTAGE CHANGE vs LOAD CURRENT 0.10 3.4 VIN = 3.8V VO = 3.3V ILOAD = 0mA 0.08 0.06 0.04 0.02 0.00 -0.02 -0.04 -0.06 VO = 3.3V IO = 0mA 3.3 OUTPUT VOLTAGE, VO (V) OUTPUT VOLTAGE CHANGE (%) 200 150 LOAD CURRENT - IO (mA) INPUT VOLTAGE (V) 3.2 IO = 150mA 3.1 IO = 300mA 3.0 2.9 -0.08 -0.10 -40 2.8 -25 5 -10 20 35 50 65 TEMPERATURE (°C) 80 95 110 125 DROPOUT VOLTAGE, VDO (mV) OUTPUT VOLTAGE, VO (V) 2.7 IO = 150mA 2.6 IO = 300mA 2.5 2.4 3.6 4.1 4.6 5.1 5.6 6.1 INPUT VOLTAGE (V) FIGURE 5. OUTPUT VOLTAGE vs INPUT VOLTAGE (2.8V OUTPUT) FN9234 Rev 2.00 May 5, 2008 4.6 5.1 5.6 6.1 6.5 350 VO = 2.8V 2.8 3.1 4.1 FIGURE 4. OUTPUT VOLTAGE vs INPUT VOLTAGE (3.3V OUTPUT) 2.9 2.3 2.6 3.6 INPUT VOLTAGE (V) FIGURE 3. OUTPUT VOLTAGE CHANGE vs TEMPERATURE IO = 0mA 3.1 6.5 300 250 VO = 2.8V 200 VO = 3.3V 150 100 50 0 0 50 100 150 200 250 OUTPUT LOAD (mA) 300 350 FIGURE 6. DROPOUT VOLTAGE vs LOAD CURRENT Page 4 of 9 400 ISL9005 Typical Performance Curves (Continued) 80 350 VO = 3.3V 70 GROUND CURRENT (µA) DROPOUT VOLTAGE, VDO (mV) 300 250 +85°C +25°C -40°C 200 150 100 +125°C 60 +25°C 50 -40°C 40 VO = 3.3V 30 50 0 0 50 100 150 200 250 OUTPUT LOAD (mA) 300 350 20 400 3.0 3.5 4.0 4.58 5.0 5.5 6.5 6.0 INPUT VOLTAGE (V) FIGURE 7. DROPOUT VOLTAGE vs LOAD CURRENT FIGURE 8. GROUND CURRENT vs INPUT VOLTAGE 80 200 180 70 140 GROUND CURRENT (µA) GROUND CURRENT (µA) 160 +25°C +85°C 120 -40°C 100 80 60 40 50 40 VIN = 3.8V VO = 3.3V 20 0 60 0 50 100 150 200 250 300 350 VIN = 3.8V VO = 3.3V ILOAD = 0µA 30 20 -40 -25 400 -10 5 LOAD CURRENT (mA) FIGURE 9. GROUND CURRENT vs LOAD 20 35 50 65 TEMPERATURE (°C) 80 5 VIN = 5.0V VO = 2.85V IL = 150mA CL = 1µF 3 4 2 VO (V) VOLTAGE (V) 110 125 FIGURE 10. GROUND CURRENT vs TEMPERATURE VO = 2.85V IL = 150mA VIN 3 VO 2 VEN (V) 0 0.5 1 0 1 0 95 1.0 1.5 2.0 2.5 TIME (s) 3.0 3.5 4.0 FIGURE 11. POWER-UP/POWER-DOWN FN9234 Rev 2.00 May 5, 2008 4.5 5.0 5 0 0 0.2 0.4 0.6 0.8 1.0 1.2 TIME (ms) 1.4 1.6 1.8 2.0 FIGURE 12. TURN-ON/TURN-OFF RESPONSE Page 5 of 9 ISL9005 Typical Performance Curves (Continued) VO = 3.3V ILOAD = 300mA VO = 2.8V ILOAD = 300mA CLOAD = 1µF CLOAD = 1µF 4.3V 4.2V 3.6V 3.5V 10mV/DIV 10mV/DIV 400µs/DIV 400µs/DIV FIGURE 13. LINE TRANSIENT RESPONSE, 3.3V OUTPUT FIGURE 14. LINE TRANSIENT RESPONSE, 2.8V OUTPUT VO (25mV/DIV) VO = 1.8V VIN = 2.8V 300mA ILOAD SPECTRAL NOISE DENSITY (µV/Hz) 10 1 0.1 VIN = 3.6V VO = 1.8V ILOAD = 10mA CIN = 1µF CLOAD = 1µF 0.01 100µA 0.001 10 100 1k 10k FREQUENCY (Hz) 100µs/DIV FIGURE 15. LOAD TRANSIENT RESPONSE 100k FIGURE 16. SPECTRAL NOISE DENSITY vs FREQUENCY 100 VIN = 3.6V VO = 1.8V IO = 10mA CLOAD = 1µF 90 80 PSRR (dB) 70 60 50 40 30 20 10 0 100 1k 10k FREQUENCY (Hz) 100k 1M FIGURE 17. PSRR vs FREQUENCY FN9234 Rev 2.00 May 5, 2008 1M Page 6 of 9 ISL9005 Pin Description PIN NUMBER PIN NAME 1 VIN Supply Voltage/LDO Input: Connect a 1µF capacitor to GND. 2 EN LDO Enable. 3 NC Do not connect. 4 NC Do not connect. 5 GND 6 NC Do not connect. 7 NC Do not connect. 8 VO LDO Output: Connect capacitor of value 1µF to 10µF to GND (1µF recommended). DESCRIPTION GND is the connection to system ground. Connect to PCB Ground plane. Typical Application ISL9005 1 VIN (2.3 TO 5V) ON 2 ENABLE OFF 3 C1 4 VIN VO EN NC NC NC NC GND 8 VOUT 7 6 5 C2 C1, C2: 1µF X5R CERAMIC CAPACITOR © Copyright Intersil Americas LLC 2005-2008. All Rights Reserved. All trademarks and registered trademarks are the property of their respective owners. For additional products, see www.intersil.com/en/products.html Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as noted in the quality certifications found at www.intersil.com/en/support/qualandreliability.html Intersil products are sold by description only. Intersil may modify the circuit design and/or specifications of products at any time without notice, provided that such modification does not, in Intersil's sole judgment, affect the form, fit or function of the product. Accordingly, the reader is cautioned to verify that datasheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com FN9234 Rev 2.00 May 5, 2008 Page 7 of 9 ISL9005 During operation, whenever the VIN voltage drops below about 1.84V, the ISL9005 immediately disables the LDO output. When VIN rises back above 2.1V, the device re-initiates its start-up sequence and LDO operation will resume automatically. Block Diagram VIN VO UVLO CONTROL LOGIC Reference Generation The reference generation circuitry includes a trimmed bandgap, a trimmed voltage reference divider, a trimmed current reference generator, and an RC noise filter. SHORT CIRCUIT, THERMAL PROTECTION, SOFT-START The bandgap generates a zero temperature coefficient (TC) voltage for the reference divider. The reference divider provides the regulation reference and other voltage references required for current generation and overtemperature detection. + EN The current generator outputs references required for adaptive biasing as well as references for LDO output current limit and thermal shutdown determination. LDO Regulation and Programmable Output Divider GND BANDGAP AND TEMPERATURE SENSOR VOLTAGE AND REFERENCE GENERATOR 1.0V 0.94V 0.9V GND Functional Description The ISL9005 contains all circuitry required to implement a high performance LDO. High performance is achieved through a circuit that delivers fast transient response to varying load conditions. In a quiescent condition, the ISL9005 adjusts its biasing to achieve the lowest standby current consumption. The device also integrates current limit protection, smart thermal shutdown protection, and soft-start. Smart Thermal shutdown protects the device against overheating. Power Control The ISL9005 has an enable pin (EN) to control power to the LDO output. When EN is low, the device is in shutdown mode. During this condition, all on-chip circuits are off, and the device draws minimum current, typically less than 0.1µA. When the enable pin is asserted, the device first polls the output of the UVLO detector to ensure that VIN voltage is at least about 2.1V. Once verified, the device initiates a start-up sequence. During the start-up sequence, trim settings are first read and latched. Then, sequentially, the bandgap, reference voltage and current generation circuitry power-up. Once the references are stable, a fast-start circuit powers up the LDO. FN9234 Rev 2.00 May 5, 2008 The LDO Regulator is implemented with a high-gain operational amplifier driving a PMOS pass transistor. The design of the ISL9005 provides a regulator that has low quiescent current, fast transient response, and overall stability across all operating and load current conditions. LDO stability is guaranteed for a 1µF to 10µF output capacitor that has a tolerance better than 20% and ESR less than 200m. The design is performance-optimized for a 1µF capacitor. Unless limited by the application, use of an output capacitor value above 4.7µF is not recommended as LDO performance improvement is minimal. Soft-start circuitry integrated into each LDO limits the initial ramp-up rate to about 30µs/V to minimize current surge. The ISL9005 provides short-circuit protection by limiting the output current to about 425mA. The LDO uses an independently trimmed 1V reference as its input. An internal resistor divider drops the LDO output voltage down to 1V. This is compared to the 1V reference for regulation. The resistor division ratio is programmed in the factory. Overheat Detection The bandgap outputs a proportional-to-temperature current that is indicative of the temperature of the silicon. This current is compared with references to determine if the device is in danger of damage due to overheating. When the die temperature reaches about +140°C, if the LDO is sourcing more than 50mA it shuts down until the die cools sufficiently. Once the die temperature falls back below about +110°C, the disabled LDO is re-enabled and soft-start automatically takes place. Page 8 of 9 ISL9005 Dual Flat No-Lead Plastic Package (DFN) L8.2x3 2X 8 LEAD DUAL FLAT NO-LEAD PLASTIC PACKAGE 0.15 C A A D 2X 0.15 C B E MILLIMETERS SYMBOL MIN A 0.80 A1 - 6 A3 INDEX AREA b TOP VIEW D2 // 0.10 A SIDE VIEW C SEATING PLANE D2 (DATUM B) C 0.08 C 0.20 A3 7 8 0.90 1.00 - - 0.05 - 0.25 0.32 1 5,8 1.50 1.65 1.75 7,8 3.00 BSC 1.65 e 1.80 1.90 7,8 0.50 BSC - k 0.20 - - - L 0.30 0.40 0.50 8 N 8 Nd 4 D2/2 6 INDEX AREA NOTES 2.00 BSC E E2 MAX 0.20 REF D B NOMINAL 2 3 Rev. 0 6/04 2 NX k NOTES: 1. Dimensioning and tolerancing conform to ASME Y14.5-1994. 2. N is the number of terminals. 3. Nd refers to the number of terminals on D. (DATUM A) E2 4. All dimensions are in millimeters. Angles are in degrees. E2/2 5. Dimension b applies to the metallized terminal and is measured between 0.25mm and 0.30mm from the terminal tip. NX L N N-1 NX b e 8 6. The configuration of the pin #1 identifier is optional, but must be located within the zone indicated. The pin #1 identifier may be either a mold or mark feature. 5 0.10 (Nd-1)Xe REF. M C A B 7. Dimensions D2 and E2 are for the exposed pads which provide improved electrical and thermal performance. 8. Nominal dimensions are provided to assist with PCB Land Pattern Design efforts, see Intersil Technical Brief TB389. BOTTOM VIEW CL (A1) NX (b) L 5 SECTION "C-C" C C e TERMINAL TIP FOR EVEN TERMINAL/SIDE FN9234 Rev 2.00 May 5, 2008 Page 9 of 9