KD3008-CF10A

KD3008-CF10A Printheads For Gaming Equipment, ATMs : CF, CG series KD3008-CF10A Applications Plain-paper printers Low speed ticket vendors Measuring terminal printers Features Utilizing the ideal element structure for each model (CF series: 100mm/s, CG series: 150mm/s) ensures perfect print quality and efficient energy consumption. In addition, the units feature a high-frequency clock, enabling advance control. Dimensions (Unit : mm) 230.5±0.3 (HEATSINK WIDTH) 230 (SUBSTRATE WIDTH) 219.5424 (EFFECTIVE PRINT WIDTH) Dot #2592 CL MAX.20.1 Dot #1 RESIN COATING FOR PROTECTION IC No.15 CONNECTOR.B No.1 No.15 CONNECTOR.A No.1 5.1±0.2 5±0.2 2-M3 (EFFECTIVE DEPTH 3) 220.5±0.2 CENTER OF HEAT ELEMENT Rev.A (10.2) 2.6±0.1 1/4 KD3008-CF10A Printheads Equivalent circuit DOT #2592 DOT #1 VH VH GND 2592 1873 1872 1297 1296 721 720 1 GND Vdd /STB4 /STB3 /STB1 /STB2 LATCH RESISTER /LAT DI1 DO1 SHIFT RESISTER SHIFT RESISTER DI2 DO2 CLK TM CONNECTOR B ＴHＥＲＭＩＳＴＯＲ 30ｋΩ Ｂ：3950K CONNECTOR A Pin assignments CONNECTOR B No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Circuit GND GND GND GND VDD /STB3 /STB4 CLK DI1 DO1 VH VH VH VH VH CONNECTOR A No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Circuit VH VH VH VH DI2 DO2 /LAT /STB1 /STB2 TM GND GND GND GND GND Rev.A 2/4 KD3008-CF10A Printheads Timing chart tw CLK CLK(CLOCK) tsetup DI thold DI DI(DATA IN) "High":Black "Low" :White td DO DO(DATA OUT) "High":Black "Low" :White tsetup LAT thold LAT min.10µsec* /LAT(LATCH) "High": Hold "Low":T hrough tw LAT tsetup ST B /STB(STROBE) tdo tdo DRIVER OUT * If delay time for Driver Out can not be secured enough, there is a possibility that VH w ould fluctuate greatly. Please design the circuit so that VH does not exceed peak voltage (Vp). Characteristics Parameter Effective printing width Dot pitch Total dot number Average resistance value Applied voltage Applied power Print cycle Pulse width Maximum number of dots energized simultaneously Maximum clock frequency Maximum roller diameter Running life / pulse life Operating temperature Symbol − − − Rave VH PO SLT TON − − − − − Typical 219.542 0.0847 2592 1250 24.0 0.23 1.11 0.51 1296 16 φ20.0 50 / 1×108 5 to 45 Unit mm mm dots Ω V W / dot ms ms dots MHz mm km / pulses °C Rev.A 3/4 KD3008-CF10A Printheads Electrical characteristic curves 0.2 0.18 0.16 Supply E0 : (mj / dot) 0.2 0.18 0.16 0.14 0.12 0.1 0.25 0.08 0.06 0.04 0.02 0 0 0.9 1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2 SLT : (ms) 180 160 140 RESISTANCE : (kΩ) Max. E0 : (mj / dot) 0.14 0.12 0.1 0.25 0.08 0.06 0.04 0.02 0 0 0.9 1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2 SLT : (ms) 120 100 80 60 40 20 0 −20 −10 0 10 20 30 40 50 60 70 TEMPERATURE : (°C) Fig.1 Adaptive speed chart Fig.2 Maximum energy curve Fig. 3 Thermistor curve Rev.A 4/4 Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of which would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. It is our top priority to supply products with the utmost quality and reliability. However, there is always a chance of failure due to unexpected factors. Therefore, please take into account the derating characteristics and allow for sufficient safety features, such as extra margin, anti-flammability, and fail-safe measures when designing in order to prevent possible accidents that may result in bodily harm or fire caused by component failure. ROHM cannot be held responsible for any damages arising from the use of the products under conditions out of the range of the specifications or due to non-compliance with the NOTES specified in this catalog. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact your nearest sales office. ROHM Customer Support System www.rohm.com Copyright © 2007 ROHM CO.,LTD. THE AMERICAS / EUPOPE / ASIA / JAPAN Contact us : webmaster@ rohm.co. jp 21, Saiin Mizosaki-cho, Ukyo-ku, Kyoto 615-8585, Japan TEL : +81-75-311-2121 FAX : +81-75-315-0172 Appendix1-Rev2.0